2018-10-30 15:02:11 +01:00
|
|
|
# ASRock H81M-HDS
|
|
|
|
|
|
|
|
This page describes how to run coreboot on the [ASRock H81M-HDS].
|
|
|
|
|
|
|
|
## Required proprietary blobs
|
|
|
|
|
2018-12-21 11:47:03 +01:00
|
|
|
```eval_rst
|
|
|
|
Please see :doc:`../../northbridge/intel/haswell/mrc.bin`.
|
2018-10-30 15:02:11 +01:00
|
|
|
```
|
|
|
|
|
|
|
|
## Building coreboot
|
|
|
|
|
|
|
|
A fully working image should be possible just by setting your MAC
|
|
|
|
address and obtaining the Haswell mrc. You can set the basic config
|
|
|
|
with the following commands. However, it is strongly advised to use
|
|
|
|
`make menuconfig` afterwards (or instead), so that you can see all of
|
|
|
|
the settings.
|
|
|
|
|
|
|
|
```bash
|
|
|
|
make distclean # Note: this will remove your current config, if it exists.
|
|
|
|
touch .config
|
|
|
|
./util/scripts/config --enable VENDOR_ASROCK
|
|
|
|
./util/scripts/config --enable BOARD_ASROCK_H81M_HDS
|
|
|
|
./util/scripts/config --enable HAVE_MRC
|
|
|
|
./util/scripts/config --set-str REALTEK_8168_MACADDRESS "xx:xx:xx:xx:xx:xx" # Fill this in!
|
|
|
|
make olddefconfig
|
|
|
|
```
|
|
|
|
|
|
|
|
If you don't plan on using coreboot's serial console to collect logs,
|
|
|
|
you might want to disable it at this point (`./util/scripts/config
|
|
|
|
--disable CONSOLE_SERIAL`). It should reduce the boot time by several
|
|
|
|
seconds. However, a more flexible method is to change the console log
|
|
|
|
level from within an OS using `util/nvramtool`, or with the `nvramcui`
|
|
|
|
payload.
|
|
|
|
|
|
|
|
Now, run `make` to build the coreboot image.
|
|
|
|
|
|
|
|
## Flashing coreboot
|
|
|
|
|
|
|
|
### Internal programming
|
|
|
|
|
|
|
|
The main SPI flash can be accessed using [flashrom]. By default, only
|
|
|
|
the BIOS region of the flash is writable. If you wish to change any
|
|
|
|
other region, such as the Management Engine or firmware descriptor, then
|
|
|
|
an external programmer is required (unless you find a clever way around
|
|
|
|
the flash protection).
|
|
|
|
|
|
|
|
The following command may be used to flash coreboot:
|
|
|
|
|
|
|
|
```bash
|
|
|
|
sudo flashrom -p internal --ifd -i bios --noverify-all -w coreboot.rom
|
|
|
|
```
|
|
|
|
|
|
|
|
The use of `--noverify-all` is required since the Management Engine
|
|
|
|
region is not readable even by the host.
|
|
|
|
|
|
|
|
### External programming
|
|
|
|
|
|
|
|
The flash chip is a 4 MiB socketed DIP-8 chip. Specifically, it's a
|
|
|
|
Winbond W25Q32FV, whose datasheet can be found [here][W25Q32FV].
|
|
|
|
The chip is located to the bottom right-hand side of the board. For
|
|
|
|
a precise location, refer to section 1.4 (Motherboard Layout) of the
|
|
|
|
[board manual], where the chip is labelled "32Mb BIOS". Take note of
|
|
|
|
the chip's orientation, remove it from its socket, and flash it with
|
|
|
|
an external programmer. For reference, the notch in the chip should be
|
|
|
|
facing towards the bottom of the board.
|
|
|
|
|
|
|
|
## Known issues
|
|
|
|
|
|
|
|
- PCIe graphics is non-functional. The PCIe 16x slot doesn't work
|
|
|
|
with other devices, either.
|
|
|
|
|
|
|
|
- The VGA port doesn't work until the OS reinitialises the display.
|
|
|
|
|
|
|
|
- There is no automatic, OS-independent fan control. This is because
|
|
|
|
the super I/O hardware monitor can only obtain valid CPU temperature
|
|
|
|
readings from the PECI agent, but the required driver doesn't exist
|
|
|
|
in coreboot. The `coretemp` driver can still be used for accurate CPU
|
|
|
|
temperature readings from an OS.
|
|
|
|
|
|
|
|
## Untested
|
|
|
|
|
|
|
|
- parallel port
|
|
|
|
- PS/2 keyboard
|
|
|
|
- EHCI debug
|
|
|
|
- TPM
|
|
|
|
- infrared module
|
|
|
|
- chassis intrusion header
|
|
|
|
- chassis speaker header
|
|
|
|
|
|
|
|
## Working
|
|
|
|
|
|
|
|
- USB
|
|
|
|
- S3 suspend/resume
|
|
|
|
- Gigabit Ethernet
|
|
|
|
- integrated graphics
|
|
|
|
- PCIe (but not the 16x slot, see [Known issues](#known-issues))
|
|
|
|
- SATA
|
|
|
|
- PS/2 mouse
|
|
|
|
- serial port
|
|
|
|
- hardware monitor (see [Known issues](#known-issues))
|
|
|
|
- onboard audio
|
|
|
|
- front panel audio
|
|
|
|
- initialisation with Haswell mrc version 1.6.1 build 2
|
|
|
|
- graphics init with libgfxinit (see [Known issues](#known-issues))
|
|
|
|
- flashrom under the vendor firmware
|
|
|
|
- flashrom under coreboot
|
|
|
|
- Wake-on-LAN
|
|
|
|
- Using `me_cleaner`
|
|
|
|
|
|
|
|
## Technology
|
|
|
|
|
|
|
|
```eval_rst
|
|
|
|
+------------------+--------------------------------------------------+
|
|
|
|
| Northbridge | Intel Haswell |
|
|
|
|
+------------------+--------------------------------------------------+
|
|
|
|
| Southbridge | Intel Lynx Point (H81) |
|
|
|
|
+------------------+--------------------------------------------------+
|
|
|
|
| CPU | Intel Haswell (LGA1150) |
|
|
|
|
+------------------+--------------------------------------------------+
|
|
|
|
| Super I/O | Nuvoton NCT6776 |
|
|
|
|
+------------------+--------------------------------------------------+
|
|
|
|
| EC | None |
|
|
|
|
+------------------+--------------------------------------------------+
|
|
|
|
| Coprocessor | Intel Management Engine |
|
|
|
|
+------------------+--------------------------------------------------+
|
|
|
|
```
|
|
|
|
|
|
|
|
[ASRock H81M-HDS]: https://www.asrock.com/mb/Intel/H81M-HDS/
|
|
|
|
[W25Q32FV]: https://www.winbond.com/resource-files/w25q32fv%20revi%2010202015.pdf
|
|
|
|
[flashrom]: https://flashrom.org/Flashrom
|
|
|
|
[Board manual]: http://asrock.pc.cdn.bitgravity.com/Manual/H81M-HDS.pdf
|