coreboot-kgpe-d16/Documentation/mainboard/sifive/hifive-unleashed.md

105 lines
3.5 KiB
Markdown
Raw Normal View History

# SiFive HiFive Unleashed
This page describes how to run coreboot on the [HiFive Unleashed] development
board from [SiFive], the first RISC-V board on the market with enough resources
to run a multiuser operating system.
For general setup instructions, please refer to the [Getting Started Guide].
## TODO
The following things are still missing from this coreboot port:
- Trampoline in the MBR block to support boot mode 1
- SiFive UART driver
- CBMEM support
- FU540 clock configuration
- FU540 RAM init
- Placing the ramstage in DRAM
- Starting the U54 cores
- FU540 PIN configuration and GPIO access macros
- FU540 OTP driver and serial number read-out
- Support for booting Linux on RISC-V
## Configuration
Run `make menuconfig` and select _SiFive_/_HiFive Unleashed_ in the _Mainboard_
menu.
### Boot modes
A total of 16 boot modes can be configured using the switches labeled `MSEL0`
through `MSEL3`. The most important ones are as follows:
- **MSEL=1**: Jump directly into the SPI flash, bypassing ROM1
- **MSEL=11**: Load FSBL from SD-card
- **MSEL=15**: Default boot mode; Load FSBL/coreboot from a GPT partition on
SPI flash
## Flashing coreboot
The HiFive Unleashed has an 32 MiB SPI flash (**ISSI IS25WP256D**), that can be
programmed from within Linux running on the board, via USB/JTAG, or directly
with an SPI programmer.
### Internal programming
The SPI flash can be accessed as `/dev/mtd0` from Linux.
### USB/JTAG
To program the flash via USB/JTAG, connect the USB port to a computer. If the
board is powered on, two new serial ports, for example `/dev/ttyUSB0` and
`/dev/ttyUSB1` will appear. The first is JTAG, and the second is connected to
the SoC's UART.
- Download and build the [RISC-V fork of OpenOCD].
- Download the [OpenOCD script] for Freedom Unleashed.
- Start OpenOCD with `openocd -f openocd.cfg`
- Connect to OpenOCD's command interface (via telnet) and enter the line
marked with `> `:
```
> flash write_image erase unlock build/coreboot.rom 0x20000000
auto erase enabled
auto unlock enabled
wrote 33554432 bytes from file build/coreboot.rom in 1524.943848s (21.488 KiB/s)
```
Note that programming the whole flash with OpenOCD isn't fast. In this
example it took just over 25 minutes. This process can be sped up
considerably by building/flashing a smaller image; OpenOCD does not check if
the image and the flash have the same size.
### External programming
External programming with an SPI adapter and [flashrom] may work, but has not
been tested. Please study the [schematics] before going this route.
## Error codes
The zeroth-stage bootloader (ZSBL) in ROM1 can print error codes on the serial
console in certain situations.
```
// Error codes are formatted as follows:
// [63:60] [59:56] [55:0]
// bootstage trap errorcode
// If trap == 1, then errorcode is actually the mcause register with the
// interrupt bit shifted to bit 55.
```
(--- from the [SiFive forum](https://forums.sifive.com/t/loading-fsbl-from-sd/1156/4))
[HiFive Unleashed]: https://www.crowdsupply.com/sifive/hifive-unleashed
[SiFive]: https://www.sifive.com/
[Getting Started Guide]: https://www.sifive.com/documentation/boards/hifive-unleashed/hifive-unleashed-getting-started-guide/
[RISC-V fork of OpenOCD]: https://github.com/riscv/riscv-openocd
[OpenOCD script]: https://github.com/sifive/freedom-u-sdk/blob/057a47f657fa33e2c60df7f183884a68e90381cc/bsp/env/freedom-u500-unleashed/openocd.cfg
[flashrom]: https://flashrom.org/Flashrom
[schematics]: https://www.sifive.com/documentation/boards/hifive-unleashed/hifive-unleashed-schematics/