72 lines
2.4 KiB
Markdown
72 lines
2.4 KiB
Markdown
|
# Flashing with fwupd
|
||
|
|
|
||
|
|
#### **Requirements:**
|
||
|
|
|
||
|
|
* fwupd version 1.5.6 or later
|
||
|
|
* The battery must be charged to at least 30%
|
||
|
|
* The charger must be connected (either USB-C or DC Jack)
|
||
|
|
* BIOS Lock must be disabled
|
||
|
|
* Supported Linux distribution (Ubuntu 20.04 +, Linux Mint 20.1 + elementaryOS 6 +, Manjaro 21+)
|
||
|
|
|
||
|
|
**fwupd 1.5.6 or later**
|
||
|
|
To check the version of **fwupd** you have installed, open a terminal window and enter the below command:
|
||
|
|
|
||
|
|
```
|
||
|
|
fwupdmgr --version
|
||
|
|
```
|
||
|
|
|
||
|
|
This will show the version number. **1.5.6** or greater will work.
|
||
|
|
|
||
|
|
On Ubuntu 20.04, Ubuntu 20.10, Linux Mint 20.1 and elementaryOS 6, fwupd 1.5.6 can be installed from our PPA with the below terminal commands:
|
||
|
|
|
||
|
|
```
|
||
|
|
sudo add-apt-repository ppa:starlabs/ppa
|
||
|
|
sudo apt update
|
||
|
|
sudo apt install fwupd
|
||
|
|
```
|
||
|
|
|
||
|
|
On Manjaro:
|
||
|
|
|
||
|
|
```
|
||
|
|
sudo pacman -Sy fwupd-git flashrom-starlabs
|
||
|
|
```
|
||
|
|
|
||
|
|
Instructions for other distributions will be added once fwupd 1.5.6 is available. If you are not using one of the distributions listed above, it is possible to install coreboot using a Live USB.
|
||
|
|
|
||
|
|
**Disable BIOS Lock**
|
||
|
|
BIOS Lock must be disabled when switching from the standard AMI (American Megatrends Inc.) firmware to coreboot. To disable BIOS Lock:
|
||
|
|
|
||
|
|
1\. Start with your LabTop turned off\. Turn it on whilst holding the **F2** key to access the BIOS settings.
|
||
|
|
2\. When the BIOS settings load, use the arrow keys to navigate to the **Advanced** tab\. Here you will see **BIOS Lock**\.
|
||
|
|
3\. Press `Enter` to change this setting from **Enabled** to **Disabled**
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
4\. Next, press the `F10` key to **Save & Exit** and then `Enter` to confirm.
|
||
|
|
|
||
|
|
#### **Switching Branch**
|
||
|
|
|
||
|
|
Switching branch refers to changing from AMI firmware to coreboot, or vice versa.
|
||
|
|
|
||
|
|
First, check for new firmware files with the below terminal command:
|
||
|
|
|
||
|
|
```
|
||
|
|
fwupdmgr refresh --force
|
||
|
|
```
|
||
|
|
|
||
|
|
Then, to change branch, enter the below terminal command:
|
||
|
|
|
||
|
|
```
|
||
|
|
fwupdmgr switch-branch
|
||
|
|
```
|
||
|
|
|
||
|
|
You can then select which branch you would like to use, by typing in the corresponding number:
|
||
|
|
|
||
|
|
You will be prompted to confirm, press `y` to continue or `n` to cancel.
|
||
|
|
|
||
|
|
Once the switch has been completed, you will be prompted to restart.
|
||
|
|
|
||
|
|
The next reboot can take up to **5 minutes,** do not interrupt this process or disconnect the charger. Once the reboot is complete, that's it - you'll continue to receive updates for whichever branch you are using.
|
||
|
|
|
||
|
|
You can switch branch at any time.
|