coreboot-kgpe-d16/src/mainboard/msi/ms7260/Options.lb

##
## This file is part of the LinuxBIOS project.
##
## Copyright (C) 2007 Uwe Hermann <uwe@hermann-uwe.de>
##
## This program is free software; you can redistribute it and/or modify
## it under the terms of the GNU General Public License as published by
## the Free Software Foundation; either version 2 of the License, or
## (at your option) any later version.
##
## This program is distributed in the hope that it will be useful,
## but WITHOUT ANY WARRANTY; without even the implied warranty of
## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
## GNU General Public License for more details.
##
## You should have received a copy of the GNU General Public License
## along with this program; if not, write to the Free Software
## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
##

uses HAVE_MP_TABLE
uses HAVE_PIRQ_TABLE
uses USE_FALLBACK_IMAGE
uses USE_FAILOVER_IMAGE
uses HAVE_FALLBACK_BOOT
uses HAVE_FAILOVER_BOOT
uses HAVE_HARD_RESET
uses IRQ_SLOT_COUNT
uses HAVE_OPTION_TABLE
uses CONFIG_MAX_CPUS
uses CONFIG_MAX_PHYSICAL_CPUS
uses CONFIG_LOGICAL_CPUS
uses CONFIG_IOAPIC
uses CONFIG_SMP
uses FALLBACK_SIZE
uses FAILOVER_SIZE
uses ROM_SIZE
uses ROM_SECTION_SIZE
uses ROM_IMAGE_SIZE
uses ROM_SECTION_SIZE
uses ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_PRECOMPRESSED_PAYLOAD
uses PAYLOAD_SIZE
uses _ROMBASE
uses XIP_ROM_SIZE
uses XIP_ROM_BASE
uses STACK_SIZE
uses HEAP_SIZE
uses USE_OPTION_TABLE
uses LB_CKS_RANGE_START
uses LB_CKS_RANGE_END
uses LB_CKS_LOC
uses MAINBOARD_PART_NUMBER
uses MAINBOARD_VENDOR
uses MAINBOARD
uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
uses LINUXBIOS_EXTRA_VERSION
uses _RAMBASE
uses TTYS0_BAUD
uses TTYS0_BASE
uses TTYS0_LCS
uses DEFAULT_CONSOLE_LOGLEVEL
uses MAXIMUM_CONSOLE_LOGLEVEL
uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
uses CONFIG_CONSOLE_SERIAL8250
uses HAVE_INIT_TIMER			# ?
uses CROSS_COMPILE
uses CC
uses HOSTCC
uses OBJCOPY
uses CONFIG_CHIP_NAME
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_USBDEBUG_DIRECT
uses HW_MEM_HOLE_SIZEK
uses HW_MEM_HOLE_SIZE_AUTO_INC
uses K8_HT_FREQ_1G_SUPPORT
uses HT_CHAIN_UNITID_BASE
uses HT_CHAIN_END_UNITID_BASE
uses SB_HT_CHAIN_ON_BUS0
uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses USE_DCACHE_RAM
uses DCACHE_RAM_BASE
uses DCACHE_RAM_SIZE
uses DCACHE_RAM_GLOBAL_VAR_SIZE
uses CONFIG_USE_INIT
uses SERIAL_CPU_INIT
uses ENABLE_APIC_EXT_ID
uses APIC_ID_OFFSET
uses LIFT_BSP_APIC_ID
uses CONFIG_PCI_64BIT_PREF_MEM
uses CONFIG_LB_MEM_TOPK
uses CONFIG_AP_CODE_IN_CAR
uses MEM_TRAIN_SEQ
uses WAIT_BEFORE_CPUS_INIT
uses CONFIG_USE_PRINTK_IN_CAR

default ROM_SIZE = 512 * 1024
default FALLBACK_SIZE = (256 * 1024) - (4 * 1024)
default FAILOVER_SIZE = 4 * 1024
default CONFIG_LB_MEM_TOPK = 2048	# 1MB more for pgtbl.
default HAVE_FALLBACK_BOOT = 1
default HAVE_FAILOVER_BOOT = 1
default HAVE_HARD_RESET = 1
default HAVE_PIRQ_TABLE = 1
default IRQ_SLOT_COUNT = 11		# TODO: Check if correct.
default HAVE_MP_TABLE = 1		# TODO: Check if correct.
default HAVE_OPTION_TABLE = 1
default CONFIG_SMP = 1
default CONFIG_MAX_CPUS = 2
default CONFIG_MAX_PHYSICAL_CPUS = 1
default CONFIG_LOGICAL_CPUS = 1
# default SERIAL_CPU_INIT = 0
default ENABLE_APIC_EXT_ID = 0
default APIC_ID_OFFSET = 0x10
default LIFT_BSP_APIC_ID = 1
default CONFIG_CHIP_NAME = 1

# Move the default LinuxBIOS CMOS range off of AMD RTC registers.
default LB_CKS_RANGE_START = 49
default LB_CKS_RANGE_END = 122
default LB_CKS_LOC = 123

# Memory hole size. 0 means disable, others will enable the hole. In that
# case, if it is smaller than mmio_basek, it will use mmio_basek instead.
# default HW_MEM_HOLE_SIZEK = 0x200000	# 2GB
default HW_MEM_HOLE_SIZEK = 0x100000	# 1GB
# default HW_MEM_HOLE_SIZEK = 0x80000	# 512MB

# Make auto increase hole size to avoid hole_startk equal to basek so as
# to make some kernel happy.
# default HW_MEM_HOLE_SIZE_AUTO_INC = 1

# Opteron K8 1G HT support.
default K8_HT_FREQ_1G_SUPPORT = 1

# HT Unit ID offset, default is 1, the typical one, 0 means only one HT device.
default HT_CHAIN_UNITID_BASE = 0

# Real SB Unit ID, default is 0x20, mean don't touch it at last.
# default HT_CHAIN_END_UNITID_BASE = 0x6

# Make the SB HT chain on bus 0, default is not (0).
default SB_HT_CHAIN_ON_BUS0 = 2

# Only offset for SB chain? Default is yes (1).
default SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0

# Allow capable device use that above 4GB.
# default CONFIG_PCI_64BIT_PREF_MEM = 1

default CONFIG_CONSOLE_VGA = 1		# Needed for VGA.
default CONFIG_PCI_ROM_RUN = 1		# Needed for VGA.
default CONFIG_USBDEBUG_DIRECT = 0
default USE_DCACHE_RAM = 1
default DCACHE_RAM_BASE = 0xc8000
default DCACHE_RAM_SIZE = 0x08000
default DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000
default CONFIG_USE_INIT = 0
default CONFIG_AP_CODE_IN_CAR = 0
default MEM_TRAIN_SEQ = 2
default WAIT_BEFORE_CPUS_INIT = 0
default CONFIG_IOAPIC = 1
default MAINBOARD_PART_NUMBER = "K9N Neo (MS-7260)"
default MAINBOARD_VENDOR = "MSI"
default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462
default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x7260
default ROM_IMAGE_SIZE = 65536
default STACK_SIZE = 0x2000
default HEAP_SIZE = 0x8000
default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE)
default _RAMBASE = 0x00100000
default CONFIG_ROM_PAYLOAD = 1
default CC = "$(CROSS_COMPILE)gcc -m32"
default HOSTCC = "gcc"
default CONFIG_USE_PRINTK_IN_CAR = 1
default CONFIG_CONSOLE_SERIAL8250 = 1
default TTYS0_BAUD = 115200
default TTYS0_BASE = 0x3f8
default TTYS0_LCS = 0x3
default DEFAULT_CONSOLE_LOGLEVEL = 9
default MAXIMUM_CONSOLE_LOGLEVEL = 9
default MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON"

end