baskingridge: dev, recovery, and WP switch support

This commit adds support for the deveveloper, recovery,
and write protect querying. It just uses jumpers on the
Basking Ridge board.

Noted ability to togggle jumpers results in toggling the
respective modes.

Change-Id: Iac189a1fa0245654591e2e9075380db422a329a0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2676
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This commit is contained in:
Aaron Durbin 2012-12-13 16:51:41 -06:00 committed by Stefan Reinauer
parent bdd89d0dc2
commit 0160d76152
1 changed files with 26 additions and 19 deletions

View File

@ -27,6 +27,7 @@
#include <device/pci.h>
#endif
#include <southbridge/intel/lynxpoint/pch.h>
#include <southbridge/intel/lynxpoint/gpio.h>
#ifndef __PRE_RAM__
#include <boot/coreboot_tables.h>
@ -44,30 +45,30 @@ void fill_lb_gpios(struct lb_gpios *gpios)
if (!gpio_base)
return;
u32 gp_lvl = inl(gpio_base + 0x0c);
u32 gp_lvl2 = inl(gpio_base + 0x38);
/* u32 gp_lvl3 = inl(gpio_base + 0x48); */
u32 gp_lvl = inl(gpio_base + GP_LVL);
u32 gp_lvl2 = inl(gpio_base + GP_LVL2);
u32 gp_lvl3 = inl(gpio_base + GP_LVL3);
gpios->size = sizeof(*gpios) + (GPIO_COUNT * sizeof(struct lb_gpio));
gpios->count = GPIO_COUNT;
/* Write Protect: GPIO48 */
gpios->gpios[0].port = 48;
/* Write Protect: GPIO22 */
gpios->gpios[0].port = 0;
gpios->gpios[0].polarity = ACTIVE_LOW;
gpios->gpios[0].value = (gp_lvl2 >> (48-32)) & 1;
gpios->gpios[0].value = (gp_lvl >> 22) & 1;
strncpy((char *)gpios->gpios[0].name,"write protect",
GPIO_MAX_NAME_LENGTH);
/* Recovery: GPIO22 */
gpios->gpios[1].port = 22;
gpios->gpios[1].polarity = ACTIVE_LOW;
gpios->gpios[1].value = (gp_lvl >> 22) & 1;
/* Recovery: GPIO69 - SV_DETECT - J8E3 (silkscreen: J8E2) */
gpios->gpios[1].port = 69;
gpios->gpios[1].polarity = ACTIVE_HIGH;
gpios->gpios[1].value = (gp_lvl3 >> (69-64)) & 1;
strncpy((char *)gpios->gpios[1].name,"recovery", GPIO_MAX_NAME_LENGTH);
/* Developer: GPIO57 */
gpios->gpios[2].port = 57;
/* Developer: GPIO48 - BIOS_RESP - J8E4 (silkscreen: J8E3) */
gpios->gpios[2].port = 48;
gpios->gpios[2].polarity = ACTIVE_LOW;
gpios->gpios[2].value = (gp_lvl2 >> (57-32)) & 1;
gpios->gpios[2].value = (gp_lvl2 >> (48-32)) & 1;
strncpy((char *)gpios->gpios[2].name,"developer", GPIO_MAX_NAME_LENGTH);
/* Hard code the lid switch GPIO to open. */
@ -99,10 +100,13 @@ int get_developer_mode_switch(void)
dev = dev_find_slot(0, PCI_DEVFN(0x1f,0));
#endif
u16 gpio_base = pci_read_config32(dev, GPIOBASE) & 0xfffe;
u32 gp_lvl2 = inl(gpio_base + 0x38);
u32 gp_lvl2 = inl(gpio_base + GP_LVL2);
/* Developer: GPIO17, active high */
return (gp_lvl2 >> (57-32)) & 1;
/*
* Developer: GPIO48, Connected to J8E4, however the silkscreen says
* J8E3. The jumper is active low.
*/
return !((gp_lvl2 >> (48-32)) & 1);
}
int get_recovery_mode_switch(void)
@ -114,9 +118,12 @@ int get_recovery_mode_switch(void)
dev = dev_find_slot(0, PCI_DEVFN(0x1f,0));
#endif
u16 gpio_base = pci_read_config32(dev, GPIOBASE) & 0xfffe;
u32 gp_lvl = inl(gpio_base + 0x0c);
u32 gp_lvl3 = inl(gpio_base + GP_LVL3);
/* Recovery: GPIO22, active low */
return !((gp_lvl >> 22) & 1);
/*
* Recovery: GPIO69, Connected to J8E3, however the silkscreen says
* J8E2. The jump is active high.
*/
return (gp_lvl3 >> (69-64)) & 1;
}