GNUBoot
/
coreboot-kgpe-d16
2
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

mb/google/brya/var/kano: swap TPM i2c with TS i2c for the next build phase 

Kano EVT will exchange i2c port for touchscreen and cr50.

BUG=b:195853169
TEST=build pass

Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I500f0721689ca66b65b8fb1deb79bef2bd988465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This commit is contained in:
David Wu 2021-11-23 11:26:44 +08:00 committed by Felix Held
parent 19072dcd6f
commit 02cef7a4a8
3 changed files with 68 additions and 43 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

11
src/mainboard/google/brya/Kconfig
View File

@ -72,7 +72,16 @@ config DEVICETREE
config DRIVER_TPM_I2C_BUS
hex
default 0x3
default 0x3 if BOARD_GOOGLE_BRYA0
default 0x3 if BOARD_GOOGLE_BRASK
default 0x3 if BOARD_GOOGLE_PRIMUS
default 0x3 if BOARD_GOOGLE_GIMBLE
default 0x3 if BOARD_GOOGLE_REDRIX
default 0x1 if BOARD_GOOGLE_KANO
default 0x3 if BOARD_GOOGLE_TAEKO
default 0x3 if BOARD_GOOGLE_FELWINTER
default 0x3 if BOARD_GOOGLE_ANAHERA
default 0x3 if BOARD_GOOGLE_VELL
config DRIVER_TPM_I2C_ADDR
hex

8
src/mainboard/google/brya/variants/kano/gpio.c
View File

@ -108,10 +108,6 @@ static const struct pad_config early_gpio_table[] = {
PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT),
/* B4 : PROC_GP3 ==> SSD_PERST_L */
PAD_CFG_GPO(GPP_B4, 0, DEEP),
/* B7 : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */
PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2),
/* B8 : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */
PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2),
/*
* D1 : ISH_GP1 ==> FP_RST_ODL
* FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down.
@ -133,6 +129,10 @@ static const struct pad_config early_gpio_table[] = {
PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP),
/* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */
PAD_CFG_GPI(GPP_F18, NONE, DEEP),
/* H6 : I2C1_SDA ==> PCH_I2C_TPM_SDA */
PAD_CFG_NF(GPP_H6, NONE, DEEP, NF1),
/* H7 : I2C1_SCL ==> PCH_I2C_TPM_SCL */
PAD_CFG_NF(GPP_H7, NONE, DEEP, NF1),
/* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */
PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2),
/* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */

92
src/mainboard/google/brya/variants/kano/overridetree.cb
View File

@ -36,14 +36,30 @@ chip soc/intel/alderlake
#+-------------------+---------------------------+
#| GSPI1 | Fingerprint MCU |
#| I2C0 | Audio |
#| I2C1 | Touchscreen |
#| I2C2 | SAR0 |
#| I2C3 | cr50 TPM. Early init is |
#| I2C1 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| I2C2 | SAR0 |
#| I2C3 | Touchscreen |
#| I2C5 | Trackpad |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.i2c[1] = {
.early_init = 1,
.speed = I2C_SPEED_FAST,
.rise_time_ns = 600,
.fall_time_ns = 400,
.data_hold_time_ns = 50,
},
.i2c[3] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 650,
.fall_time_ns = 400,
.data_hold_time_ns = 50,
},
}"
device domain 0 on
device ref dtt on
chip drivers/intel/dptf
@ -232,37 +248,10 @@ chip soc/intel/alderlake
end
end #I2C0
device ref i2c1 on
chip drivers/i2c/hid
register "generic.hid" = ""ELAN90FC""
register "generic.desc" = ""ELAN Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
register "generic.reset_delay_ms" = "300"
register "generic.reset_off_delay_ms" = "1"
register "generic.enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
register "generic.enable_delay_ms" = "6"
register "generic.stop_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
register "generic.stop_off_delay_ms" = "1"
register "generic.has_power_resource" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 0x10 on end
end
chip drivers/generic/gpio_keys
register "name" = ""PENH""
# GPP_D6 is the IRQ source, and GPP_D17 is the wake source
register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_D6)"
register "key.wake_gpe" = "GPE0_DW1_17"
register "key.wakeup_route" = "WAKEUP_ROUTE_SCI"
register "key.wakeup_event_action" = "EV_ACT_DEASSERTED"
register "key.dev_name" = ""EJCT""
register "key.linux_code" = "SW_PEN_INSERTED"
register "key.linux_input_type" = "EV_SW"
register "key.label" = ""pen_eject""
device generic 0 on end
chip drivers/i2c/tpm
register "hid" = ""GOOG0005""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
device i2c 50 on end
end
end
device ref i2c2 on
@ -421,10 +410,37 @@ chip soc/intel/alderlake
end
end
device ref i2c3 on
chip drivers/i2c/tpm
register "hid" = ""GOOG0005""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
device i2c 50 on end
chip drivers/i2c/hid
register "generic.hid" = ""ELAN90FC""
register "generic.desc" = ""ELAN Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
register "generic.reset_delay_ms" = "300"
register "generic.reset_off_delay_ms" = "1"
register "generic.enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
register "generic.enable_delay_ms" = "6"
register "generic.stop_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
register "generic.stop_off_delay_ms" = "1"
register "generic.has_power_resource" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 0x10 on end
end
chip drivers/generic/gpio_keys
register "name" = ""PENH""
# GPP_D6 is the IRQ source, and GPP_D17 is the wake source
register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_D6)"
register "key.wake_gpe" = "GPE0_DW1_17"
register "key.wakeup_route" = "WAKEUP_ROUTE_SCI"
register "key.wakeup_event_action" = "EV_ACT_DEASSERTED"
register "key.dev_name" = ""EJCT""
register "key.linux_code" = "SW_PEN_INSERTED"
register "key.linux_input_type" = "EV_SW"
register "key.label" = ""pen_eject""
device generic 0 on end
end
end
device ref i2c5 on