mb/google/brya/var/kano: swap TPM i2c with TS i2c for the next build phase

Kano EVT will exchange i2c port for touchscreen and cr50.

BUG=b:195853169
TEST=build pass

Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I500f0721689ca66b65b8fb1deb79bef2bd988465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>

src/mainboard/google/brya/Kconfig

@@ -72,7 +72,16 @@ config DEVICETREE
 
 config DRIVER_TPM_I2C_BUS
 	hex
-	default 0x3
+	default 0x3 if BOARD_GOOGLE_BRYA0
+	default 0x3 if BOARD_GOOGLE_BRASK
+	default 0x3 if BOARD_GOOGLE_PRIMUS
+	default 0x3 if BOARD_GOOGLE_GIMBLE
+	default 0x3 if BOARD_GOOGLE_REDRIX
+	default 0x1 if BOARD_GOOGLE_KANO
+	default 0x3 if BOARD_GOOGLE_TAEKO
+	default 0x3 if BOARD_GOOGLE_FELWINTER
+	default 0x3 if BOARD_GOOGLE_ANAHERA
+	default 0x3 if BOARD_GOOGLE_VELL
 
 config DRIVER_TPM_I2C_ADDR
 	hex

src/mainboard/google/brya/variants/kano/gpio.c

@@ -108,10 +108,6 @@ static const struct pad_config early_gpio_table[] = {
 	PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT),
 	/* B4  : PROC_GP3 ==> SSD_PERST_L */
 	PAD_CFG_GPO(GPP_B4, 0, DEEP),
-	/* B7  : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */
-	PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2),
-	/* B8  : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */
-	PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2),
 	/*
 	 * D1  : ISH_GP1 ==> FP_RST_ODL
 	 * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down.
@@ -133,6 +129,10 @@ static const struct pad_config early_gpio_table[] = {
 	PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP),
 	/* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */
 	PAD_CFG_GPI(GPP_F18, NONE, DEEP),
+	/* H6  : I2C1_SDA ==> PCH_I2C_TPM_SDA */
+	PAD_CFG_NF(GPP_H6, NONE, DEEP, NF1),
+	/* H7  : I2C1_SCL ==> PCH_I2C_TPM_SCL */
+	PAD_CFG_NF(GPP_H7, NONE, DEEP, NF1),
 	/* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */
 	PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2),
 	/* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */

src/mainboard/google/brya/variants/kano/overridetree.cb

@@ -36,14 +36,30 @@ chip soc/intel/alderlake
 	#+-------------------+---------------------------+
 	#| GSPI1             | Fingerprint MCU           |
 	#| I2C0              | Audio                     |
-	#| I2C1              | Touchscreen               |
+	#| I2C1              | cr50 TPM. Early init is   |
-	#| I2C2              | SAR0                      |
-	#| I2C3              | cr50 TPM. Early init is   |
 	#|                   | required to set up a BAR  |
 	#|                   | for TPM communication     |
+	#| I2C2              | SAR0                      |
+	#| I2C3              | Touchscreen               |
 	#| I2C5              | Trackpad                  |
 	#+-------------------+---------------------------+
 
+	register "common_soc_config" = "{
+		.i2c[1] = {
+			.early_init = 1,
+			.speed = I2C_SPEED_FAST,
+			.rise_time_ns = 600,
+			.fall_time_ns = 400,
+			.data_hold_time_ns = 50,
+		},
+		.i2c[3] = {
+			.speed = I2C_SPEED_FAST,
+			.rise_time_ns = 650,
+			.fall_time_ns = 400,
+			.data_hold_time_ns = 50,
+		},
+	}"
+
 	device domain 0 on
 		device ref dtt on
 			chip drivers/intel/dptf
@@ -232,37 +248,10 @@ chip soc/intel/alderlake
 			end
 		end #I2C0
 		device ref i2c1 on
-			chip drivers/i2c/hid
+			chip drivers/i2c/tpm
-				register "generic.hid" = ""ELAN90FC""
+				register "hid" = ""GOOG0005""
-				register "generic.desc" = ""ELAN Touchscreen""
+				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
-				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+				device i2c 50 on end
-				register "generic.probed" = "1"
-				register "generic.reset_gpio" =
-							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
-				register "generic.reset_delay_ms" = "300"
-				register "generic.reset_off_delay_ms" = "1"
-				register "generic.enable_gpio" =
-							"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
-				register "generic.enable_delay_ms" = "6"
-				register "generic.stop_gpio" =
-							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
-				register "generic.stop_off_delay_ms" = "1"
-				register "generic.has_power_resource" = "1"
-				register "hid_desc_reg_offset" = "0x01"
-				device i2c 0x10 on end
-			end
-			chip drivers/generic/gpio_keys
-				register "name" = ""PENH""
-				# GPP_D6 is the IRQ source, and GPP_D17 is the wake source
-				register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_D6)"
-				register "key.wake_gpe" = "GPE0_DW1_17"
-				register "key.wakeup_route" = "WAKEUP_ROUTE_SCI"
-				register "key.wakeup_event_action" = "EV_ACT_DEASSERTED"
-				register "key.dev_name" = ""EJCT""
-				register "key.linux_code" = "SW_PEN_INSERTED"
-				register "key.linux_input_type" = "EV_SW"
-				register "key.label" = ""pen_eject""
-				device generic 0 on end
 			end
 		end
 		device ref i2c2 on
@@ -421,10 +410,37 @@ chip soc/intel/alderlake
                         end
 		end
 		device ref i2c3 on
-			chip drivers/i2c/tpm
+			chip drivers/i2c/hid
-				register "hid" = ""GOOG0005""
+				register "generic.hid" = ""ELAN90FC""
-				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
+				register "generic.desc" = ""ELAN Touchscreen""
-				device i2c 50 on end
+				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+				register "generic.probed" = "1"
+				register "generic.reset_gpio" =
+							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+				register "generic.reset_delay_ms" = "300"
+				register "generic.reset_off_delay_ms" = "1"
+				register "generic.enable_gpio" =
+							"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+				register "generic.enable_delay_ms" = "6"
+				register "generic.stop_gpio" =
+							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+				register "generic.stop_off_delay_ms" = "1"
+				register "generic.has_power_resource" = "1"
+				register "hid_desc_reg_offset" = "0x01"
+				device i2c 0x10 on end
+			end
+			chip drivers/generic/gpio_keys
+				register "name" = ""PENH""
+				# GPP_D6 is the IRQ source, and GPP_D17 is the wake source
+				register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_D6)"
+				register "key.wake_gpe" = "GPE0_DW1_17"
+				register "key.wakeup_route" = "WAKEUP_ROUTE_SCI"
+				register "key.wakeup_event_action" = "EV_ACT_DEASSERTED"
+				register "key.dev_name" = ""EJCT""
+				register "key.linux_code" = "SW_PEN_INSERTED"
+				register "key.linux_input_type" = "EV_SW"
+				register "key.label" = ""pen_eject""
+				device generic 0 on end
 			end
 		end
 		device ref i2c5 on