libpayload: Add UART for qcs405
TEST=build Change-Id: I43164cf9eacc844af1d048f7b6ebbda96fc9d202 Signed-off-by: Prudhvi Yarlagadda <pyarlaga@codeaurora.org> Signed-off-by: Sricharan R <sricharan@codeaurora.org> Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/29957 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This commit is contained in:
Prudhvi Yarlagadda
Patrick Georgi
parent
12f0e42cb4
commit
1b05479a7f
|
|
@ -258,6 +258,11 @@ config IPQ40XX_SERIAL_CONSOLE
|
|||
depends on SERIAL_CONSOLE
|
||||
default n
|
||||
|
||||
config QCS405_SERIAL_CONSOLE
|
||||
bool "QCS405 SOC compatible serial port driver"
|
||||
depends on SERIAL_CONSOLE
|
||||
default n
|
||||
|
||||
config PL011_SERIAL_CONSOLE
|
||||
bool "PL011 compatible serial port driver"
|
||||
depends on 8250_SERIAL_CONSOLE
|
||||
|
|
|
|||
|
|
@ -1,3 +1,5 @@
|
|||
CONFIG_LP_CHROMEOS=y
|
||||
CONFIG_LP_ARCH_ARM64=y
|
||||
CONFIG_LP_TIMER_ARM64_ARCH=y
|
||||
CONFIG_LP_SERIAL_CONSOLE=y
|
||||
CONFIG_LP_QCS405_SERIAL_CONSOLE=y
|
||||
|
|
|
|||
|
|
@ -37,6 +37,7 @@ libc-$(CONFIG_LP_8250_SERIAL_CONSOLE) += serial/8250.c serial/serial.c
|
|||
libc-$(CONFIG_LP_S5P_SERIAL_CONSOLE) += serial/s5p.c serial/serial.c
|
||||
libc-$(CONFIG_LP_IPQ806X_SERIAL_CONSOLE) += serial/ipq806x.c serial/serial.c
|
||||
libc-$(CONFIG_LP_IPQ40XX_SERIAL_CONSOLE) += serial/ipq40xx.c serial/serial.c
|
||||
libc-$(CONFIG_LP_QCS405_SERIAL_CONSOLE) += serial/qcs405.c serial/serial.c
|
||||
libc-$(CONFIG_LP_PC_KEYBOARD) += i8042/keyboard.c
|
||||
libc-$(CONFIG_LP_PC_MOUSE) += i8042/mouse.c
|
||||
libc-$(CONFIG_LP_PC_I8042) += i8042/i8042.c
|
||||
|
|
|
|||
|
|
@ -0,0 +1,555 @@
|
|||
/*
|
||||
* Copyright (c) 2010-2012, 2014, 2016, 2019, The Linux Foundation.
|
||||
* All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions are
|
||||
* met:
|
||||
* * Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* * Redistributions in binary form must reproduce the above
|
||||
* copyright notice, this list of conditions and the following
|
||||
* disclaimer in the documentation and/or other materials provided
|
||||
* with the distribution.
|
||||
* * Neither the name of The Linux Foundation nor the names of its
|
||||
* contributors may be used to endorse or promote products derived
|
||||
* from this software without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
|
||||
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
||||
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
|
||||
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
|
||||
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
||||
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
||||
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
|
||||
* BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
|
||||
* WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
|
||||
* OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
|
||||
* IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||||
*/
|
||||
|
||||
#include <libpayload.h>
|
||||
|
||||
#define UART_DM_CLK_RX_TX_BIT_RATE 0xFF
|
||||
|
||||
enum MSM_BOOT_UART_DM_PARITY_MODE {
|
||||
MSM_BOOT_UART_DM_NO_PARITY,
|
||||
MSM_BOOT_UART_DM_ODD_PARITY,
|
||||
MSM_BOOT_UART_DM_EVEN_PARITY,
|
||||
MSM_BOOT_UART_DM_SPACE_PARITY
|
||||
};
|
||||
|
||||
/* UART Stop Bit Length */
|
||||
enum MSM_BOOT_UART_DM_STOP_BIT_LEN {
|
||||
MSM_BOOT_UART_DM_SBL_9_16,
|
||||
MSM_BOOT_UART_DM_SBL_1,
|
||||
MSM_BOOT_UART_DM_SBL_1_9_16,
|
||||
MSM_BOOT_UART_DM_SBL_2
|
||||
};
|
||||
|
||||
/* UART Bits per Char */
|
||||
enum MSM_BOOT_UART_DM_BITS_PER_CHAR {
|
||||
MSM_BOOT_UART_DM_5_BPS,
|
||||
MSM_BOOT_UART_DM_6_BPS,
|
||||
MSM_BOOT_UART_DM_7_BPS,
|
||||
MSM_BOOT_UART_DM_8_BPS
|
||||
};
|
||||
|
||||
/* 8-N-1 Configuration */
|
||||
#define MSM_BOOT_UART_DM_8_N_1_MODE (MSM_BOOT_UART_DM_NO_PARITY | \
|
||||
(MSM_BOOT_UART_DM_SBL_1 << 2) | \
|
||||
(MSM_BOOT_UART_DM_8_BPS << 4))
|
||||
|
||||
/* UART_DM Registers */
|
||||
|
||||
/* UART Operational Mode Register */
|
||||
#define MSM_BOOT_UART_DM_MR1(base) ((base) + 0x00)
|
||||
#define MSM_BOOT_UART_DM_MR2(base) ((base) + 0x04)
|
||||
#define MSM_BOOT_UART_DM_RXBRK_ZERO_CHAR_OFF (1 << 8)
|
||||
#define MSM_BOOT_UART_DM_LOOPBACK (1 << 7)
|
||||
|
||||
#define PERIPH_BLK_BLSP 1
|
||||
|
||||
/* UART Clock Selection Register */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_CSR(base) ((base) + 0xA0)
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_CSR(base) ((base) + 0x08)
|
||||
#endif
|
||||
|
||||
/* UART DM TX FIFO Registers - 4 */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_TF(base, x) ((base) + 0x100+(4*(x)))
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_TF(base, x) ((base) + 0x70+(4*(x)))
|
||||
#endif
|
||||
|
||||
/* UART Command Register */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_CR(base) ((base) + 0xA8)
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_CR(base) ((base) + 0x10)
|
||||
#endif
|
||||
#define MSM_BOOT_UART_DM_CR_RX_ENABLE (1 << 0)
|
||||
#define MSM_BOOT_UART_DM_CR_RX_DISABLE (1 << 1)
|
||||
#define MSM_BOOT_UART_DM_CR_TX_ENABLE (1 << 2)
|
||||
#define MSM_BOOT_UART_DM_CR_TX_DISABLE (1 << 3)
|
||||
|
||||
/* UART Channel Command */
|
||||
#define MSM_BOOT_UART_DM_CR_CH_CMD_LSB(x) ((x & 0x0f) << 4)
|
||||
#define MSM_BOOT_UART_DM_CR_CH_CMD_MSB(x) ((x >> 4) << 11)
|
||||
#define MSM_BOOT_UART_DM_CR_CH_CMD(x) \
|
||||
(MSM_BOOT_UART_DM_CR_CH_CMD_LSB(x) | MSM_BOOT_UART_DM_CR_CH_CMD_MSB(x))
|
||||
#define MSM_BOOT_UART_DM_CMD_NULL MSM_BOOT_UART_DM_CR_CH_CMD(0)
|
||||
#define MSM_BOOT_UART_DM_CMD_RESET_RX MSM_BOOT_UART_DM_CR_CH_CMD(1)
|
||||
#define MSM_BOOT_UART_DM_CMD_RESET_TX MSM_BOOT_UART_DM_CR_CH_CMD(2)
|
||||
#define MSM_BOOT_UART_DM_CMD_RESET_ERR_STAT MSM_BOOT_UART_DM_CR_CH_CMD(3)
|
||||
#define MSM_BOOT_UART_DM_CMD_RES_BRK_CHG_INT MSM_BOOT_UART_DM_CR_CH_CMD(4)
|
||||
#define MSM_BOOT_UART_DM_CMD_START_BRK MSM_BOOT_UART_DM_CR_CH_CMD(5)
|
||||
#define MSM_BOOT_UART_DM_CMD_STOP_BRK MSM_BOOT_UART_DM_CR_CH_CMD(6)
|
||||
#define MSM_BOOT_UART_DM_CMD_RES_CTS_N MSM_BOOT_UART_DM_CR_CH_CMD(7)
|
||||
#define MSM_BOOT_UART_DM_CMD_RES_STALE_INT MSM_BOOT_UART_DM_CR_CH_CMD(8)
|
||||
#define MSM_BOOT_UART_DM_CMD_PACKET_MODE MSM_BOOT_UART_DM_CR_CH_CMD(9)
|
||||
#define MSM_BOOT_UART_DM_CMD_MODE_RESET MSM_BOOT_UART_DM_CR_CH_CMD(C)
|
||||
#define MSM_BOOT_UART_DM_CMD_SET_RFR_N MSM_BOOT_UART_DM_CR_CH_CMD(D)
|
||||
#define MSM_BOOT_UART_DM_CMD_RES_RFR_N MSM_BOOT_UART_DM_CR_CH_CMD(E)
|
||||
#define MSM_BOOT_UART_DM_CMD_RES_TX_ERR MSM_BOOT_UART_DM_CR_CH_CMD(10)
|
||||
#define MSM_BOOT_UART_DM_CMD_CLR_TX_DONE MSM_BOOT_UART_DM_CR_CH_CMD(11)
|
||||
#define MSM_BOOT_UART_DM_CMD_RES_BRKSTRT_INT MSM_BOOT_UART_DM_CR_CH_CMD(12)
|
||||
#define MSM_BOOT_UART_DM_CMD_RES_BRKEND_INT MSM_BOOT_UART_DM_CR_CH_CMD(13)
|
||||
#define MSM_BOOT_UART_DM_CMD_RES_PER_FRM_INT MSM_BOOT_UART_DM_CR_CH_CMD(14)
|
||||
|
||||
/*UART General Command */
|
||||
#define MSM_UART_DM_CR_GENERAL_CMD(x) ((x) << 8)
|
||||
|
||||
#define MSM_BOOT_UART_DM_GCMD_NULL MSM_UART_DM_CR_GENERAL_CMD(0)
|
||||
#define MSM_BOOT_UART_DM_GCMD_CR_PROT_EN MSM_UART_DM_CR_GENERAL_CMD(1)
|
||||
#define MSM_BOOT_UART_DM_GCMD_CR_PROT_DIS MSM_UART_DM_CR_GENERAL_CMD(2)
|
||||
#define MSM_BOOT_UART_DM_GCMD_RES_TX_RDY_INT MSM_UART_DM_CR_GENERAL_CMD(3)
|
||||
#define MSM_BOOT_UART_DM_GCMD_SW_FORCE_STALE MSM_UART_DM_CR_GENERAL_CMD(4)
|
||||
#define MSM_BOOT_UART_DM_GCMD_ENA_STALE_EVT MSM_UART_DM_CR_GENERAL_CMD(5)
|
||||
#define MSM_BOOT_UART_DM_GCMD_DIS_STALE_EVT MSM_UART_DM_CR_GENERAL_CMD(6)
|
||||
|
||||
/* UART Interrupt Mask Register */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_IMR(base) ((base) + 0xB0)
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_IMR(base) ((base) + 0x14)
|
||||
#endif
|
||||
|
||||
#define MSM_BOOT_UART_DM_TXLEV (1 << 0)
|
||||
#define MSM_BOOT_UART_DM_RXHUNT (1 << 1)
|
||||
#define MSM_BOOT_UART_DM_RXBRK_CHNG (1 << 2)
|
||||
#define MSM_BOOT_UART_DM_RXSTALE (1 << 3)
|
||||
#define MSM_BOOT_UART_DM_RXLEV (1 << 4)
|
||||
#define MSM_BOOT_UART_DM_DELTA_CTS (1 << 5)
|
||||
#define MSM_BOOT_UART_DM_CURRENT_CTS (1 << 6)
|
||||
#define MSM_BOOT_UART_DM_TX_READY (1 << 7)
|
||||
#define MSM_BOOT_UART_DM_TX_ERROR (1 << 8)
|
||||
#define MSM_BOOT_UART_DM_TX_DONE (1 << 9)
|
||||
#define MSM_BOOT_UART_DM_RXBREAK_START (1 << 10)
|
||||
#define MSM_BOOT_UART_DM_RXBREAK_END (1 << 11)
|
||||
#define MSM_BOOT_UART_DM_PAR_FRAME_ERR_IRQ (1 << 12)
|
||||
|
||||
#define MSM_BOOT_UART_DM_IMR_ENABLED (MSM_BOOT_UART_DM_TX_READY | \
|
||||
MSM_BOOT_UART_DM_TXLEV | \
|
||||
MSM_BOOT_UART_DM_RXSTALE)
|
||||
|
||||
/* UART Interrupt Programming Register */
|
||||
#define MSM_BOOT_UART_DM_IPR(base) ((base) + 0x18)
|
||||
#define MSM_BOOT_UART_DM_STALE_TIMEOUT_LSB 0x0f
|
||||
#define MSM_BOOT_UART_DM_STALE_TIMEOUT_MSB 0 /* Not used currently */
|
||||
|
||||
/* UART Transmit/Receive FIFO Watermark Register */
|
||||
#define MSM_BOOT_UART_DM_TFWR(base) ((base) + 0x1C)
|
||||
/* Interrupt is generated when FIFO level is less than or equal to this value */
|
||||
#define MSM_BOOT_UART_DM_TFW_VALUE 0
|
||||
|
||||
#define MSM_BOOT_UART_DM_RFWR(base) ((base) + 0x20)
|
||||
/*Interrupt generated when no of words in RX FIFO is greater than this value */
|
||||
#define MSM_BOOT_UART_DM_RFW_VALUE 0
|
||||
|
||||
/* UART Hunt Character Register */
|
||||
#define MSM_BOOT_UART_DM_HCR(base) ((base) + 0x24)
|
||||
|
||||
/* Used for RX transfer initialization */
|
||||
#define MSM_BOOT_UART_DM_DMRX(base) ((base) + 0x34)
|
||||
|
||||
/* Default DMRX value - any value bigger than FIFO size would be fine */
|
||||
#define MSM_BOOT_UART_DM_DMRX_DEF_VALUE 0x220
|
||||
|
||||
/* Register to enable IRDA function */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_IRDA(base) ((base) + 0xB8)
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_IRDA(base) ((base) + 0x38)
|
||||
#endif
|
||||
|
||||
/* UART Data Mover Enable Register */
|
||||
#define MSM_BOOT_UART_DM_DMEN(base) ((base) + 0x3C)
|
||||
|
||||
/* Number of characters for Transmission */
|
||||
#define MSM_BOOT_UART_DM_NO_CHARS_FOR_TX(base) ((base) + 0x040)
|
||||
|
||||
/* UART RX FIFO Base Address */
|
||||
#define MSM_BOOT_UART_DM_BADR(base) ((base) + 0x44)
|
||||
|
||||
/* UART Status Register */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_SR(base) ((base) + 0x0A4)
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_SR(base) ((base) + 0x008)
|
||||
#endif
|
||||
#define MSM_BOOT_UART_DM_SR_RXRDY (1 << 0)
|
||||
#define MSM_BOOT_UART_DM_SR_RXFULL (1 << 1)
|
||||
#define MSM_BOOT_UART_DM_SR_TXRDY (1 << 2)
|
||||
#define MSM_BOOT_UART_DM_SR_TXEMT (1 << 3)
|
||||
#define MSM_BOOT_UART_DM_SR_UART_OVERRUN (1 << 4)
|
||||
#define MSM_BOOT_UART_DM_SR_PAR_FRAME_ERR (1 << 5)
|
||||
#define MSM_BOOT_UART_DM_RX_BREAK (1 << 6)
|
||||
#define MSM_BOOT_UART_DM_HUNT_CHAR (1 << 7)
|
||||
#define MSM_BOOT_UART_DM_RX_BRK_START_LAST (1 << 8)
|
||||
|
||||
/* UART Receive FIFO Registers - 4 in numbers */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_RF(base, x) ((base) + 0x140 + (4*(x)))
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_RF(base, x) ((base) + 0x70 + (4*(x)))
|
||||
#endif
|
||||
|
||||
/* UART Masked Interrupt Status Register */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_MISR(base) ((base) + 0xAC)
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_MISR(base) ((base) + 0x10)
|
||||
#endif
|
||||
|
||||
/* UART Interrupt Status Register */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_ISR(base) ((base) + 0xB4)
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_ISR(base) ((base) + 0x14)
|
||||
#endif
|
||||
|
||||
/* Number of characters received since the end of last RX transfer */
|
||||
#if PERIPH_BLK_BLSP
|
||||
#define MSM_BOOT_UART_DM_RX_TOTAL_SNAP(base) ((base) + 0xBC)
|
||||
#else
|
||||
#define MSM_BOOT_UART_DM_RX_TOTAL_SNAP(base) ((base) + 0x38)
|
||||
#endif
|
||||
|
||||
/* UART TX FIFO Status Register */
|
||||
#define MSM_BOOT_UART_DM_TXFS(base) ((base) + 0x4C)
|
||||
#define MSM_BOOT_UART_DM_TXFS_STATE_LSB(x) \
|
||||
MSM_BOOT_UART_DM_EXTR_BITS(x, 0, 6)
|
||||
#define MSM_BOOT_UART_DM_TXFS_STATE_MSB(x) \
|
||||
MSM_BOOT_UART_DM_EXTR_BITS(x, 14, 31)
|
||||
#define MSM_BOOT_UART_DM_TXFS_BUF_STATE(x) \
|
||||
MSM_BOOT_UART_DM_EXTR_BITS(x, 7, 9)
|
||||
#define MSM_BOOT_UART_DM_TXFS_ASYNC_STATE(x) \
|
||||
MSM_BOOT_UART_DM_EXTR_BITS(x, 10, 13)
|
||||
|
||||
/* UART RX FIFO Status Register */
|
||||
#define MSM_BOOT_UART_DM_RXFS(base) ((base) + 0x50)
|
||||
#define MSM_BOOT_UART_DM_RXFS_STATE_LSB(x) \
|
||||
MSM_BOOT_UART_DM_EXTR_BITS(x, 0, 6)
|
||||
#define MSM_BOOT_UART_DM_RXFS_STATE_MSB(x) \
|
||||
MSM_BOOT_UART_DM_EXTR_BITS(x, 14, 31)
|
||||
#define MSM_BOOT_UART_DM_RXFS_BUF_STATE(x) \
|
||||
MSM_BOOT_UART_DM_EXTR_BITS(x, 7, 9)
|
||||
#define MSM_BOOT_UART_DM_RXFS_ASYNC_STATE(x) \
|
||||
MSM_BOOT_UART_DM_EXTR_BITS(x, 10, 13)
|
||||
|
||||
/* Macros for Common Errors */
|
||||
#define MSM_BOOT_UART_DM_E_FAILURE 1
|
||||
#define MSM_BOOT_UART_DM_E_TIMEOUT 2
|
||||
#define MSM_BOOT_UART_DM_E_INVAL 3
|
||||
#define MSM_BOOT_UART_DM_E_MALLOC_FAIL 4
|
||||
#define MSM_BOOT_UART_DM_E_RX_NOT_READY 5
|
||||
|
||||
#define UART1_DM_BASE ((void *)0x078af000)
|
||||
#define UART2_DM_BASE ((void *)0x078b1000)
|
||||
|
||||
enum {
|
||||
BLSP1_UART1,
|
||||
BLSP1_UART2,
|
||||
};
|
||||
|
||||
#define FIFO_DATA_SIZE 4
|
||||
|
||||
struct uart_params_t {
|
||||
void *uart_dm_base;
|
||||
unsigned int blsp_uart;
|
||||
};
|
||||
|
||||
static struct console_input_driver consin = {
|
||||
.havekey = serial_havechar,
|
||||
.getchar = serial_getchar,
|
||||
};
|
||||
|
||||
static struct console_output_driver consout = {
|
||||
.putchar = serial_putchar,
|
||||
};
|
||||
|
||||
static struct uart_params_t uart_board_param = {};
|
||||
|
||||
/**
|
||||
* msm_boot_uart_dm_init_rx_transfer - Init Rx transfer
|
||||
* @uart_dm_base: UART controller base address
|
||||
*/
|
||||
static unsigned int msm_boot_uart_dm_init_rx_transfer(void *uart_dm_base)
|
||||
{
|
||||
/* Reset receiver */
|
||||
write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_CMD_RESET_RX);
|
||||
|
||||
/* Enable receiver */
|
||||
write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_CR_RX_ENABLE);
|
||||
write32(MSM_BOOT_UART_DM_DMRX(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_DMRX_DEF_VALUE);
|
||||
|
||||
/* Clear stale event */
|
||||
write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_CMD_RES_STALE_INT);
|
||||
|
||||
/* Enable stale event */
|
||||
write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_GCMD_ENA_STALE_EVT);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static unsigned int msm_boot_uart_dm_init(void *uart_dm_base);
|
||||
|
||||
static int valid_data = 0;
|
||||
|
||||
static unsigned int word = 0;
|
||||
|
||||
/**
|
||||
* msm_boot_uart_dm_read - reads a word from the RX FIFO.
|
||||
* @data: location where the read data is stored
|
||||
* @count: no of valid data in the FIFO
|
||||
*
|
||||
* Reads a word from the RX FIFO. If no data is available
|
||||
* returns %MSM_BOOT_UART_DM_E_RX_NOT_READY.
|
||||
*/
|
||||
static unsigned int
|
||||
msm_boot_uart_dm_read(unsigned int *data, int *count)
|
||||
{
|
||||
static int total_rx_data = 0;
|
||||
static int rx_data_read = 0;
|
||||
void *base;
|
||||
uint32_t status_reg;
|
||||
|
||||
base = uart_board_param.uart_dm_base;
|
||||
|
||||
if (data == NULL)
|
||||
return MSM_BOOT_UART_DM_E_INVAL;
|
||||
|
||||
status_reg = read32(MSM_BOOT_UART_DM_MISR(base));
|
||||
|
||||
/* Check for DM_RXSTALE for RX transfer to finish */
|
||||
while (!(status_reg & MSM_BOOT_UART_DM_RXSTALE)) {
|
||||
status_reg = read32(MSM_BOOT_UART_DM_MISR(base));
|
||||
return MSM_BOOT_UART_DM_E_RX_NOT_READY;
|
||||
}
|
||||
|
||||
/* Check for Overrun error. We'll just reset Error Status */
|
||||
if (read32(MSM_BOOT_UART_DM_SR(base)) &
|
||||
MSM_BOOT_UART_DM_SR_UART_OVERRUN) {
|
||||
write32(MSM_BOOT_UART_DM_CR(base),
|
||||
MSM_BOOT_UART_DM_CMD_RESET_ERR_STAT);
|
||||
total_rx_data = rx_data_read = 0;
|
||||
msm_boot_uart_dm_init(base);
|
||||
return MSM_BOOT_UART_DM_E_RX_NOT_READY;
|
||||
}
|
||||
|
||||
/* Read UART_DM_RX_TOTAL_SNAP for actual number of bytes received */
|
||||
if (total_rx_data == 0)
|
||||
total_rx_data = read32(MSM_BOOT_UART_DM_RX_TOTAL_SNAP(base));
|
||||
|
||||
/* Data available in FIFO; read a word. */
|
||||
*data = read32(MSM_BOOT_UART_DM_RF(base, 0));
|
||||
|
||||
/* increment the total count of chars we've read so far */
|
||||
rx_data_read += FIFO_DATA_SIZE;
|
||||
|
||||
/* actual count of valid data in word */
|
||||
*count = ((total_rx_data < rx_data_read) ?
|
||||
(FIFO_DATA_SIZE - (rx_data_read - total_rx_data)) :
|
||||
FIFO_DATA_SIZE);
|
||||
|
||||
/* If there are still data left in FIFO we'll read them before
|
||||
* initializing RX Transfer again
|
||||
*/
|
||||
if (rx_data_read < total_rx_data)
|
||||
return 0;
|
||||
|
||||
msm_boot_uart_dm_init_rx_transfer(base);
|
||||
total_rx_data = rx_data_read = 0;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
void serial_putchar(unsigned int data)
|
||||
{
|
||||
int num_of_chars = 1;
|
||||
void *base = uart_board_param.uart_dm_base;
|
||||
|
||||
if (data == '\n') {
|
||||
num_of_chars++;
|
||||
data = (data << 8) | '\r';
|
||||
}
|
||||
|
||||
/* Wait until transmit FIFO is empty. */
|
||||
while (!(read32(MSM_BOOT_UART_DM_SR(base)) &
|
||||
MSM_BOOT_UART_DM_SR_TXEMT))
|
||||
udelay(1);
|
||||
/*
|
||||
* TX FIFO is ready to accept new character(s). First write number of
|
||||
* characters to be transmitted.
|
||||
*/
|
||||
write32(MSM_BOOT_UART_DM_NO_CHARS_FOR_TX(base), num_of_chars);
|
||||
|
||||
/* And now write the character(s) */
|
||||
write32(MSM_BOOT_UART_DM_TF(base, 0), data);
|
||||
}
|
||||
|
||||
/*
|
||||
* msm_boot_uart_dm_reset - resets UART controller
|
||||
* @base: UART controller base address
|
||||
*/
|
||||
static unsigned int msm_boot_uart_dm_reset(void *base)
|
||||
{
|
||||
write32(MSM_BOOT_UART_DM_CR(base), MSM_BOOT_UART_DM_CMD_RESET_RX);
|
||||
write32(MSM_BOOT_UART_DM_CR(base), MSM_BOOT_UART_DM_CMD_RESET_TX);
|
||||
write32(MSM_BOOT_UART_DM_CR(base),
|
||||
MSM_BOOT_UART_DM_CMD_RESET_ERR_STAT);
|
||||
write32(MSM_BOOT_UART_DM_CR(base), MSM_BOOT_UART_DM_CMD_RES_TX_ERR);
|
||||
write32(MSM_BOOT_UART_DM_CR(base), MSM_BOOT_UART_DM_CMD_RES_STALE_INT);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
/*
|
||||
* msm_boot_uart_dm_init - initilaizes UART controller
|
||||
* @uart_dm_base: UART controller base address
|
||||
*/
|
||||
unsigned int msm_boot_uart_dm_init(void *uart_dm_base)
|
||||
{
|
||||
/* Configure UART mode registers MR1 and MR2 */
|
||||
/* Hardware flow control isn't supported */
|
||||
write32(MSM_BOOT_UART_DM_MR1(uart_dm_base), 0x0);
|
||||
|
||||
/* 8-N-1 configuration: 8 data bits - No parity - 1 stop bit */
|
||||
write32(MSM_BOOT_UART_DM_MR2(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_8_N_1_MODE);
|
||||
|
||||
/* Configure Interrupt Mask register IMR */
|
||||
write32(MSM_BOOT_UART_DM_IMR(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_IMR_ENABLED);
|
||||
|
||||
/*
|
||||
* Configure Tx and Rx watermarks configuration registers
|
||||
* TX watermark value is set to 0 - interrupt is generated when
|
||||
* FIFO level is less than or equal to 0
|
||||
*/
|
||||
write32(MSM_BOOT_UART_DM_TFWR(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_TFW_VALUE);
|
||||
|
||||
/* RX watermark value */
|
||||
write32(MSM_BOOT_UART_DM_RFWR(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_RFW_VALUE);
|
||||
|
||||
/* Configure Interrupt Programming Register */
|
||||
/* Set initial Stale timeout value */
|
||||
write32(MSM_BOOT_UART_DM_IPR(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_STALE_TIMEOUT_LSB);
|
||||
|
||||
/* Configure IRDA if required */
|
||||
/* Disabling IRDA mode */
|
||||
write32(MSM_BOOT_UART_DM_IRDA(uart_dm_base), 0x0);
|
||||
|
||||
/* Configure hunt character value in HCR register */
|
||||
/* Keep it in reset state */
|
||||
write32(MSM_BOOT_UART_DM_HCR(uart_dm_base), 0x0);
|
||||
|
||||
/*
|
||||
* Configure Rx FIFO base address
|
||||
* Both TX/RX shares same SRAM and default is half-n-half.
|
||||
* Sticking with default value now.
|
||||
* As such RAM size is (2^RAM_ADDR_WIDTH, 32-bit entries).
|
||||
* We have found RAM_ADDR_WIDTH = 0x7f
|
||||
*/
|
||||
|
||||
/* Issue soft reset command */
|
||||
msm_boot_uart_dm_reset(uart_dm_base);
|
||||
|
||||
/* Enable/Disable Rx/Tx DM interfaces */
|
||||
/* Data Mover not currently utilized. */
|
||||
write32(MSM_BOOT_UART_DM_DMEN(uart_dm_base), 0x0);
|
||||
|
||||
/* Enable transmitter */
|
||||
write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
|
||||
MSM_BOOT_UART_DM_CR_TX_ENABLE);
|
||||
|
||||
/* Initialize Receive Path */
|
||||
msm_boot_uart_dm_init_rx_transfer(uart_dm_base);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
/**
|
||||
* serial_havechar - checks if data available for reading
|
||||
*
|
||||
* Returns 1 if data available, 0 otherwise
|
||||
*/
|
||||
int serial_havechar(void)
|
||||
{
|
||||
/* Return if data is already read */
|
||||
if (valid_data)
|
||||
return 1;
|
||||
|
||||
/* Read data from the FIFO */
|
||||
if (msm_boot_uart_dm_read(&word, &valid_data) != 0)
|
||||
return 0;
|
||||
|
||||
return 1;
|
||||
}
|
||||
|
||||
/**
|
||||
* qcs405_serial_getc - reads a character
|
||||
*
|
||||
* Returns the character read from serial port.
|
||||
*/
|
||||
int serial_getchar(void)
|
||||
{
|
||||
uint8_t byte;
|
||||
|
||||
while (!serial_havechar())
|
||||
; /* wait for incoming data */
|
||||
|
||||
byte = (uint8_t)(word & 0xff);
|
||||
word = word >> 8;
|
||||
valid_data--;
|
||||
|
||||
return byte;
|
||||
}
|
||||
|
||||
/* For simplicity sake let's rely on coreboot initalizing the UART. */
|
||||
void serial_console_init(void)
|
||||
{
|
||||
struct cb_serial *sc_ptr = lib_sysinfo.serial;
|
||||
|
||||
if (!sc_ptr)
|
||||
return;
|
||||
|
||||
uart_board_param.uart_dm_base = (void *)(uintptr_t)sc_ptr->baseaddr;
|
||||
|
||||
/* TODO: We should rely on coreboot init. */
|
||||
msm_boot_uart_dm_init(uart_board_param.uart_dm_base);
|
||||
|
||||
console_add_output_driver(&consout);
|
||||
console_add_input_driver(&consin);
|
||||
}
|
||||
Loading…
Reference in New Issue