soc/qualcomm/ipq40xx: Enable USB
BUG=chrome-os-partner:49249 TEST=Compiles and Boots and detect USB storage BRANCH=none Change-Id: I9f33adccaabf436c8a8ba08033ff1221ace71aaa Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: f6b18062b7570b6aa71a72ad6185edaf00b48e2d Original-Change-Id: I86a297fc915d4886958f8490dda2c1fa00a6c9d3 Original-Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org> Original-Reviewed-on: https://chromium-review.googlesource.com/333312 Original-Commit-Ready: David Hendricks <dhendrix@chromium.org> Original-Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-on: https://review.coreboot.org/14675 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This commit is contained in:
Varadarajan Narayanan
Patrick Georgi
parent
fce799c1b2
commit
3939acaa77
|
|
@ -20,203 +20,275 @@
|
|||
#include <soc/iomap.h>
|
||||
#include <soc/usb.h>
|
||||
|
||||
#define CRPORT_TX_OVRD_DRV_LO 0x1002
|
||||
#define CRPORT_RX_OVRD_IN_HI 0x1006
|
||||
#define CRPORT_TX_ALT_BLOCK 0x102d
|
||||
/**
|
||||
* USB Hardware registers
|
||||
*/
|
||||
#define PHY_CTRL0_ADDR 0x000
|
||||
#define PHY_CTRL1_ADDR 0x004
|
||||
#define PHY_CTRL2_ADDR 0x008
|
||||
#define PHY_CTRL3_ADDR 0x00C
|
||||
#define PHY_CTRL4_ADDR 0x010
|
||||
#define PHY_MISC_ADDR 0x024
|
||||
#define PHY_IPG_ADDR 0x030
|
||||
|
||||
static u32 * const tcsr_usb_sel = (void *)0x1a4000b0;
|
||||
#define PHY_CTRL0_VAL 0xA4600015
|
||||
#define PHY_CTRL1_VAL 0x09500000
|
||||
#define PHY_CTRL2_VAL 0x00058180
|
||||
#define PHY_CTRL3_VAL 0x6DB6DCD6
|
||||
#define PHY_CTRL4_VAL 0x836DB6DB
|
||||
#define PHY_MISC_VAL 0x3803FB0C
|
||||
#define PHY_IPG_VAL 0x47323232
|
||||
|
||||
struct usb_qc_phy {
|
||||
u32 ipcat;
|
||||
u32 ctrl;
|
||||
u32 general_cfg;
|
||||
u32 ram1;
|
||||
u32 hs_phy_ctrl;
|
||||
u32 param_ovrd;
|
||||
u32 chrg_det_ctrl;
|
||||
u32 chrg_det_output;
|
||||
u32 alt_irq_en;
|
||||
u32 hs_phy_irq_stat;
|
||||
u32 cgctl;
|
||||
u32 dbg_bus;
|
||||
u32 ss_phy_ctrl;
|
||||
u32 ss_phy_param1;
|
||||
u32 ss_phy_param2;
|
||||
u32 crport_data_in;
|
||||
u32 crport_data_out;
|
||||
u32 crport_cap_addr;
|
||||
u32 crport_cap_data;
|
||||
u32 crport_ack_read;
|
||||
u32 crport_ack_write;
|
||||
};
|
||||
check_member(usb_qc_phy, crport_ack_write, 0x50);
|
||||
#define USB_HOST3_PHY_BASE ((void *)0x8a00000)
|
||||
#define USB_HOST3_BALDUR_PHY_BASE ((void *)0xa6000)
|
||||
#define GCC_USB3_RST_CTRL ((void *)0x0181E038)
|
||||
|
||||
static struct usb_qc_phy * const usb_host1_phy = (void *)USB_HOST1_PHY_BASE;
|
||||
static struct usb_qc_phy * const usb_host2_phy = (void *)USB_HOST2_PHY_BASE;
|
||||
#define DWC3_GCTL 0xc110
|
||||
#define DWC3_GUSB3PIPECTL(n) (0xc2c0 + (n * 0x04))
|
||||
#define DWC3_GUSB2PHYCFG(n) (0xc200 + (n * 0x04))
|
||||
|
||||
struct usb_dwc3 {
|
||||
u32 sbuscfg0;
|
||||
u32 sbuscfg1;
|
||||
u32 txthrcfg;
|
||||
u32 rxthrcfg;
|
||||
u32 ctl;
|
||||
u32 evten;
|
||||
u32 sts;
|
||||
u8 reserved0[4];
|
||||
u32 snpsid;
|
||||
u32 gpio;
|
||||
u32 uid;
|
||||
u32 uctl;
|
||||
u64 buserraddr;
|
||||
u64 prtbimap;
|
||||
u8 reserved1[32];
|
||||
u32 dbgfifospace;
|
||||
u32 dbgltssm;
|
||||
u32 dbglnmcc;
|
||||
u32 dbgbmu;
|
||||
u32 dbglspmux;
|
||||
u32 dbglsp;
|
||||
u32 dbgepinfo0;
|
||||
u32 dbgepinfo1;
|
||||
u64 prtbimap_hs;
|
||||
u64 prtbimap_fs;
|
||||
u8 reserved2[112];
|
||||
u32 usb2phycfg;
|
||||
u8 reserved3[60];
|
||||
u32 usb2i2cctl;
|
||||
u8 reserved4[60];
|
||||
u32 usb2phyacc;
|
||||
u8 reserved5[60];
|
||||
u32 usb3pipectl;
|
||||
u8 reserved6[60];
|
||||
};
|
||||
check_member(usb_dwc3, usb3pipectl, 0x1c0);
|
||||
/* Global USB3 PIPE Control Register */
|
||||
#define DWC3_GUSB3PIPECTL_PHYSOFTRST (1 << 31)
|
||||
#define DWC3_GUSB3PIPECTL_SUSPHY (1 << 17)
|
||||
#define DWC3_GCTL_CORESOFTRESET (1 << 11)
|
||||
#define DWC3_GCTL_PRTCAPDIR(n) ((n) << 12)
|
||||
#define DWC3_GCTL_PRTCAP_OTG 3
|
||||
#define DWC3_DCTL_CSFTRST (1 << 30)
|
||||
#define DWC3_GSNPSID 0xc120
|
||||
#define DWC3_DCTL 0xc704
|
||||
|
||||
static struct usb_dwc3 * const usb_host1_dwc3 = (void *)USB_HOST1_DWC3_BASE;
|
||||
static struct usb_dwc3 * const usb_host2_dwc3 = (void *)USB_HOST2_DWC3_BASE;
|
||||
|
||||
static void setup_dwc3(struct usb_dwc3 *dwc3)
|
||||
/* Global USB2 PHY Configuration Register */
|
||||
#define DWC3_GUSB2PHYCFG_PHYSOFTRST (1 << 31)
|
||||
#define DWC3_GUSB2PHYCFG_SUSPHY (1 << 6)
|
||||
#define DWC3_GSNPSID_MASK 0xffff0000
|
||||
#define DWC3_GEVTEN 0xc114
|
||||
|
||||
|
||||
#define DWC3_GCTL_SCALEDOWN(n) ((n) << 4)
|
||||
#define DWC3_GCTL_SCALEDOWN_MASK DWC3_GCTL_SCALEDOWN(3)
|
||||
#define DWC3_GCTL_DISSCRAMBLE (1 << 3)
|
||||
#define DWC3_GCTL_DSBLCLKGTNG (1 << 0)
|
||||
#define DWC3_GCTL_U2RSTECN (1 << 16)
|
||||
#define DWC3_REVISION_190A 0x5533190a
|
||||
|
||||
#define USB30_HS_PHY_CTRL 0x00000010
|
||||
#define SW_SESSVLD (0x01 << 0x1C)
|
||||
#define UTMI_OTG_VBUS_VALID (0x01 << 0x14)
|
||||
|
||||
#define USB30_SS_PHY_CTRL 0x00000030
|
||||
#define LANE0_PWR_PRESENT (0x01 << 0x18)
|
||||
|
||||
static void setup_dwc3(void);
|
||||
|
||||
/**
|
||||
* Write register.
|
||||
*
|
||||
* @base - PHY base virtual address.
|
||||
* @offset - register offset.
|
||||
* @val - value to write.
|
||||
*/
|
||||
static inline void qscratch_write(void *base, u32 offset, u32 val)
|
||||
{
|
||||
write32(&dwc3->usb3pipectl,
|
||||
0x1 << 31 | /* assert PHY soft reset */
|
||||
0x1 << 25 | /* (default) U1/U2 exit fail -> recovery? */
|
||||
0x1 << 24 | /* (default) activate PHY low power states */
|
||||
0x1 << 19 | /* (default) PHY low power delay value */
|
||||
0x1 << 18 | /* (default) activate PHY low power delay */
|
||||
0x1 << 1 | /* (default) Tx deemphasis value */
|
||||
0x1 << 0); /* (default) elastic buffer mode */
|
||||
|
||||
write32(&dwc3->usb2phycfg,
|
||||
0x1 << 31 | /* assert PHY soft reset */
|
||||
0x9 << 10 | /* (default) PHY clock turnaround 8-bit UTMI+ */
|
||||
0x1 << 8 | /* (default) enable PHY sleep in L1 */
|
||||
0x1 << 6); /* (default) enable PHY suspend */
|
||||
|
||||
write32(&dwc3->ctl,
|
||||
0x2 << 19 | /* (default) suspend clock scaling */
|
||||
0x1 << 16 | /* retry SS three times before HS downgrade */
|
||||
0x1 << 12 | /* port capability HOST */
|
||||
0x1 << 11 | /* assert core soft reset */
|
||||
0x1 << 10 | /* (default) sync ITP to refclk */
|
||||
0x1 << 2); /* U2 exit after 8us LFPS (instead of 248ns) */
|
||||
|
||||
write32(&dwc3->uctl,
|
||||
0x32 << 22 | /* (default) reference clock period in ns */
|
||||
0x1 << 15 | /* (default) XHCI compliant device addressing */
|
||||
0x10 << 0); /* (default) devices time out after 32us */
|
||||
|
||||
udelay(5);
|
||||
|
||||
clrbits_le32(&dwc3->ctl, 0x1 << 11); /* deassert core soft reset */
|
||||
clrbits_le32(&dwc3->usb2phycfg, 0x1 << 31); /* PHY soft reset */
|
||||
clrbits_le32(&dwc3->usb3pipectl, 0x1 << 31); /* PHY soft reset */
|
||||
write32(base + offset, val);
|
||||
}
|
||||
|
||||
static void setup_phy(struct usb_qc_phy *phy)
|
||||
/**
|
||||
* Write register and read back masked value to confirm it is written
|
||||
*
|
||||
* @base - base virtual address.
|
||||
* @offset - register offset.
|
||||
* @mask - register bitmask specifying what should be updated
|
||||
* @val - value to write.
|
||||
*/
|
||||
static inline void qscratch_write_readback(void *base, u32 offset,
|
||||
const u32 mask, u32 val)
|
||||
{
|
||||
write32(&phy->ss_phy_ctrl,
|
||||
0x1 << 24 | /* Indicate VBUS power present */
|
||||
0x1 << 8 | /* Enable USB3 ref clock to prescaler */
|
||||
0x1 << 7 | /* assert SS PHY reset */
|
||||
0x19 << 0); /* (default) reference clock multiplier */
|
||||
u32 write_val, tmp = read32(base + offset);
|
||||
|
||||
write32(&phy->hs_phy_ctrl,
|
||||
0x1 << 26 | /* (default) unclamp DPSE/DMSE VLS */
|
||||
0x1 << 25 | /* (default) select freeclk for utmi_clk */
|
||||
0x1 << 24 | /* (default) unclamp DMSE VLS */
|
||||
0x1 << 21 | /* (default) enable UTMI clock */
|
||||
0x1 << 20 | /* set OTG VBUS as valid */
|
||||
0x1 << 18 | /* use ref clock from core */
|
||||
0x1 << 17 | /* (default) unclamp DPSE VLS */
|
||||
0x1 << 11 | /* force xo/bias/pll to stay on in suspend */
|
||||
0x1 << 9 | /* (default) unclamp IDHV */
|
||||
0x1 << 8 | /* (default) unclamp VLS (again???) */
|
||||
0x1 << 7 | /* (default) unclamp HV VLS */
|
||||
0x7 << 4 | /* select frequency (no idea which one) */
|
||||
0x1 << 1); /* (default) "retention enable" */
|
||||
tmp &= ~mask; /* retain other bits */
|
||||
write_val = tmp | val;
|
||||
|
||||
write32(&phy->ss_phy_param1,
|
||||
0x6e << 20 | /* full TX swing amplitude */
|
||||
0x20 << 14 | /* (default) 6dB TX deemphasis */
|
||||
0x17 << 8 | /* 3.5dB TX deemphasis */
|
||||
0x9 << 3); /* (default) LoS detector level */
|
||||
write32(base + offset, write_val);
|
||||
|
||||
write32(&phy->general_cfg, 0x1 << 2); /* set XHCI 1.00 compliance */
|
||||
/* Read back to see if val was written */
|
||||
tmp = read32(base + offset);
|
||||
tmp &= mask; /* clear other bits */
|
||||
|
||||
udelay(5);
|
||||
clrbits_le32(&phy->ss_phy_ctrl, 0x1 << 7); /* deassert SS PHY reset */
|
||||
if (tmp != val) {
|
||||
printk(BIOS_INFO, "write: %x to QSCRATCH: %x FAILED\n",
|
||||
val, offset);
|
||||
}
|
||||
}
|
||||
|
||||
static void crport_handshake(void *capture_reg, void *acknowledge_bit, u32 data)
|
||||
static void dwc3_ipq40xx_enable_vbus_valid(void)
|
||||
{
|
||||
int usec = 100;
|
||||
/* Enable VBUS valid for HS PHY*/
|
||||
qscratch_write_readback((void *)0x8af8800, USB30_HS_PHY_CTRL,
|
||||
SW_SESSVLD, SW_SESSVLD);
|
||||
qscratch_write_readback((void *)0x8af8800, USB30_HS_PHY_CTRL,
|
||||
UTMI_OTG_VBUS_VALID, UTMI_OTG_VBUS_VALID);
|
||||
|
||||
if (capture_reg)
|
||||
write32(capture_reg, data);
|
||||
|
||||
write32(acknowledge_bit, 0x1 << 0);
|
||||
while (read32(acknowledge_bit) && --usec)
|
||||
udelay(1);
|
||||
|
||||
if (!usec)
|
||||
printk(BIOS_ERR, "CRPORT handshake timed out (0x%08x)\n", data);
|
||||
/* Enable VBUS valid for SS PHY*/
|
||||
qscratch_write_readback((void *)0x8af8800, USB30_SS_PHY_CTRL,
|
||||
LANE0_PWR_PRESENT, LANE0_PWR_PRESENT);
|
||||
}
|
||||
|
||||
static void crport_write(struct usb_qc_phy *phy, u16 addr, u16 data)
|
||||
static void qcom_baldur_hs_phy_init(void)
|
||||
{
|
||||
crport_handshake(&phy->crport_data_in, &phy->crport_cap_addr, addr);
|
||||
crport_handshake(&phy->crport_data_in, &phy->crport_cap_data, data);
|
||||
crport_handshake(NULL, &phy->crport_ack_write, 0);
|
||||
u32 reg;
|
||||
|
||||
/* assert HS PHY POR reset */
|
||||
reg = read32(GCC_USB3_RST_CTRL);
|
||||
reg = reg | 0x10;
|
||||
write32(GCC_USB3_RST_CTRL, reg);
|
||||
mdelay(10);
|
||||
|
||||
/* assert HS PHY SRIF reset */
|
||||
reg = read32(GCC_USB3_RST_CTRL);
|
||||
reg = reg | 0x4;
|
||||
write32(GCC_USB3_RST_CTRL, reg);
|
||||
mdelay(10);
|
||||
|
||||
/* deassert HS PHY SRIF reset and program HS PHY registers */
|
||||
reg = read32(GCC_USB3_RST_CTRL);
|
||||
reg = reg & ~0x4;
|
||||
write32(GCC_USB3_RST_CTRL, reg);
|
||||
|
||||
mdelay(10);
|
||||
|
||||
/* perform PHY register writes */
|
||||
write32(USB_HOST3_BALDUR_PHY_BASE + PHY_CTRL0_ADDR, PHY_CTRL0_VAL);
|
||||
write32(USB_HOST3_BALDUR_PHY_BASE + PHY_CTRL1_ADDR, PHY_CTRL1_VAL);
|
||||
write32(USB_HOST3_BALDUR_PHY_BASE + PHY_CTRL2_ADDR, PHY_CTRL2_VAL);
|
||||
write32(USB_HOST3_BALDUR_PHY_BASE + PHY_CTRL3_ADDR, PHY_CTRL3_VAL);
|
||||
write32(USB_HOST3_BALDUR_PHY_BASE + PHY_CTRL4_ADDR, PHY_CTRL4_VAL);
|
||||
write32(USB_HOST3_BALDUR_PHY_BASE + PHY_MISC_ADDR, PHY_MISC_VAL);
|
||||
write32(USB_HOST3_BALDUR_PHY_BASE + PHY_IPG_ADDR, PHY_IPG_VAL);
|
||||
|
||||
mdelay(10);
|
||||
|
||||
/* de-assert USB3 HS PHY POR reset */
|
||||
reg = read32(GCC_USB3_RST_CTRL);
|
||||
reg = reg & ~0x10;
|
||||
write32(GCC_USB3_RST_CTRL, reg);
|
||||
}
|
||||
|
||||
static void tune_phy(struct usb_qc_phy *phy)
|
||||
static void qcom_uni_ss_phy_init(void)
|
||||
{
|
||||
crport_write(phy, CRPORT_RX_OVRD_IN_HI,
|
||||
0x1 << 11 | /* Set RX_EQ override? */
|
||||
0x4 << 8 | /* Set RX_EQ to 4? */
|
||||
0x1 << 7); /* Enable RX_EQ override */
|
||||
crport_write(phy, CRPORT_TX_OVRD_DRV_LO,
|
||||
0x1 << 14 | /* Enable amplitude (override?) */
|
||||
0x17 << 7 | /* Set TX deemphasis to 23 */
|
||||
0x6e << 0); /* Set amplitude to 110 */
|
||||
crport_write(phy, CRPORT_TX_ALT_BLOCK,
|
||||
0x1 << 7); /* ALT block? ("partial RX reset") */
|
||||
u32 reg;
|
||||
|
||||
/* assert SS PHY POR reset */
|
||||
reg = read32(GCC_USB3_RST_CTRL);
|
||||
reg = reg | 0x20;
|
||||
write32(GCC_USB3_RST_CTRL, reg);
|
||||
|
||||
mdelay(100);
|
||||
|
||||
/* deassert SS PHY POR reset */
|
||||
reg = read32(GCC_USB3_RST_CTRL);
|
||||
reg = reg & ~0x20;
|
||||
write32(GCC_USB3_RST_CTRL, reg);
|
||||
}
|
||||
|
||||
void setup_dwc3(void)
|
||||
{
|
||||
u32 reg;
|
||||
u32 revision;
|
||||
|
||||
revision = read32(USB_HOST3_PHY_BASE + DWC3_GSNPSID);
|
||||
/* This should read as U3 followed by revision number */
|
||||
if ((revision & DWC3_GSNPSID_MASK) != 0x55330000)
|
||||
printk(BIOS_INFO, "Error in reading Version\n");
|
||||
|
||||
printk(BIOS_INFO, "Version = %x\n", revision);
|
||||
|
||||
/* issue device SoftReset too */
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_DCTL, DWC3_DCTL_CSFTRST);
|
||||
do {
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_DCTL);
|
||||
if (!(reg & DWC3_DCTL_CSFTRST))
|
||||
break;
|
||||
|
||||
udelay(10);
|
||||
} while (true);
|
||||
printk(BIOS_INFO, "software reset done\n");
|
||||
|
||||
/* Before Resetting PHY, put Core in Reset */
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GCTL);
|
||||
reg |= DWC3_GCTL_CORESOFTRESET;
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GCTL, reg);
|
||||
|
||||
/* Assert USB3 PHY reset */
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GUSB3PIPECTL(0));
|
||||
reg |= DWC3_GUSB3PIPECTL_PHYSOFTRST;
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GUSB3PIPECTL(0), reg);
|
||||
|
||||
/* Assert USB2 PHY reset */
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GUSB2PHYCFG(0));
|
||||
reg |= DWC3_GUSB2PHYCFG_PHYSOFTRST;
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GUSB2PHYCFG(0), reg);
|
||||
|
||||
qcom_baldur_hs_phy_init();
|
||||
qcom_uni_ss_phy_init();
|
||||
mdelay(100);
|
||||
|
||||
/* Clear USB3 PHY reset */
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GUSB3PIPECTL(0));
|
||||
reg &= ~DWC3_GUSB3PIPECTL_PHYSOFTRST;
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GUSB3PIPECTL(0), reg);
|
||||
|
||||
/* Clear USB2 PHY reset */
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GUSB2PHYCFG(0));
|
||||
reg &= ~DWC3_GUSB2PHYCFG_PHYSOFTRST;
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GUSB2PHYCFG(0), reg);
|
||||
|
||||
mdelay(100);
|
||||
|
||||
/* After PHYs are stable we can take Core out of reset state */
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GCTL);
|
||||
reg &= ~DWC3_GCTL_CORESOFTRESET;
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GCTL, reg);
|
||||
|
||||
#if 0
|
||||
/* Enable Suspend USB2.0 HS/FS/LS PHY (SusPHY) */
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GUSB2PHYCFG(0));
|
||||
reg |= DWC3_GUSB2PHYCFG_SUSPHY;
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GUSB2PHYCFG(0), reg);
|
||||
|
||||
/* Enable Suspend USB3.0 SS PHY (Suspend_en) */
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GUSB3PIPECTL(0));
|
||||
reg |= DWC3_GUSB3PIPECTL_SUSPHY;
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GUSB3PIPECTL(0), reg);
|
||||
#endif
|
||||
|
||||
/* configure controller in Host mode */
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GCTL);
|
||||
reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
|
||||
reg |= DWC3_GCTL_PRTCAPDIR(0x1); /* host mode */
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GCTL, reg);
|
||||
printk(BIOS_INFO, "USB Host mode reg = %x\n", reg);
|
||||
|
||||
reg = read32(USB_HOST3_PHY_BASE + DWC3_GCTL);
|
||||
reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
|
||||
reg &= ~DWC3_GCTL_DISSCRAMBLE;
|
||||
|
||||
reg &= ~DWC3_GCTL_DSBLCLKGTNG;
|
||||
/*
|
||||
* WORKAROUND: DWC3 revisions <1.90a have a bug
|
||||
* where the device can fail to connect at SuperSpeed
|
||||
* and falls back to high-speed mode which causes
|
||||
* the device to enter a Connect/Disconnect loop
|
||||
*/
|
||||
if (revision < DWC3_REVISION_190A)
|
||||
reg |= DWC3_GCTL_U2RSTECN;
|
||||
|
||||
write32(USB_HOST3_PHY_BASE + DWC3_GCTL, reg);
|
||||
}
|
||||
|
||||
void setup_usb_host1(void)
|
||||
{
|
||||
printk(BIOS_INFO, "Setting up USB HOST1 controller...\n");
|
||||
setbits_le32(tcsr_usb_sel, 1 << 0); /* Select DWC3 controller */
|
||||
setup_phy(usb_host1_phy);
|
||||
setup_dwc3(usb_host1_dwc3);
|
||||
tune_phy(usb_host1_phy);
|
||||
}
|
||||
|
||||
void setup_usb_host2(void)
|
||||
{
|
||||
printk(BIOS_INFO, "Setting up USB HOST2 controller...\n");
|
||||
setbits_le32(tcsr_usb_sel, 1 << 1); /* Select DWC3 controller */
|
||||
setup_phy(usb_host2_phy);
|
||||
setup_dwc3(usb_host2_dwc3);
|
||||
tune_phy(usb_host2_phy);
|
||||
printk(BIOS_INFO, "Setting up USB HOST1 controller.\n");
|
||||
setup_dwc3();
|
||||
dwc3_ipq40xx_enable_vbus_valid();
|
||||
}
|
||||
|
|
|
|||
Loading…
Reference in New Issue