soc/intel/cannonlake: Add postcar stage support

Initialize postcar frame once finish FSP memoryinit

Change-Id: I888d471fa620b7fc9f8975524a31f662e1fc5079
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/20534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>

src/drivers/intel/fsp2_0/Makefile.inc

@@ -43,6 +43,7 @@ postcar-$(CONFIG_CACHE_RELOCATED_RAMSTAGE_OUTSIDE_CBMEM) += stage_cache.c
 postcar-$(CONFIG_FSP_CAR) += temp_ram_exit.c
 postcar-$(CONFIG_FSP_CAR) += util.c
 postcar-$(CONFIG_DISPLAY_FSP_HEADER) += header_display.c
+postcar-y += hand_off_block.c
 
 CPPFLAGS_common += -I$(src)/drivers/intel/fsp2_0/include
 

src/soc/intel/cannonlake/Kconfig

@@ -23,6 +23,8 @@ config CPU_SPECIFIC_OPTIONS
 	select HAVE_INTEL_FIRMWARE
 	select INTEL_CAR_NEM_ENHANCED
 	select PLATFORM_USES_FSP2_0
+	select POSTCAR_CONSOLE
+	select POSTCAR_STAGE
 	select RELOCATABLE_RAMSTAGE
 	select SOC_INTEL_COMMON
 	select SOC_INTEL_COMMON_BLOCK_SA

src/soc/intel/cannonlake/Makefile.inc

@@ -5,20 +5,23 @@ subdirs-y += ../../../cpu/intel/microcode
 subdirs-y += ../../../cpu/x86/mtrr
 subdirs-y += ../../../cpu/x86/tsc
 
-bootblock-$(CONFIG_DRIVERS_UART_8250MEM) += uart.c
 bootblock-y += bootblock/bootblock.c
 bootblock-y += bootblock/cpu.c
 bootblock-y += bootblock/pch.c
 bootblock-y += bootblock/report_platform.c
 bootblock-y += gpio.c
+bootblock-$(CONFIG_UART_DEBUG) += uart.c
 
 romstage-y += cbmem.c
 romstage-y += reset.c
-romstage-$(CONFIG_DRIVERS_UART_8250MEM) += uart.c
+romstage-$(CONFIG_UART_DEBUG) += uart.c
 
 ramstage-y += cbmem.c
 ramstage-$(CONFIG_PLATFORM_USES_FSP2_0) += reset.c
-ramstage-$(CONFIG_DRIVERS_UART_8250MEM) += uart.c
+ramstage-$(CONFIG_UART_DEBUG) += uart.c
+
+postcar-y += memmap.c
+postcar-$(CONFIG_UART_DEBUG) += uart.c
 
 CPPFLAGS_common += -I$(src)/soc/intel/cannonlake/include/fsp20
 CPPFLAGS_common += -I$(src)/vendorcode/intel/fsp/fsp2_0/cannonlake

src/soc/intel/cannonlake/romstage/romstage.c

@@ -14,6 +14,10 @@
  */
 
 #include <arch/io.h>
+#include <arch/symbols.h>
+#include <assert.h>
+#include <cpu/x86/mtrr.h>
+#include <cpu/x86/msr.h>
 #include <cbmem.h>
 #include <console/console.h>
 #include <fsp/util.h>
@@ -25,6 +29,8 @@
 asmlinkage void car_stage_entry(void)
 {
 	bool s3wake;
+	struct postcar_frame pcf;
+	uintptr_t top_of_ram;
 	struct chipset_power_state *ps;
 
 	console_init();
@@ -36,7 +42,25 @@ asmlinkage void car_stage_entry(void)
 	timestamp_add_now(TS_START_ROMSTAGE);
 	s3wake = ps->prev_sleep_state == ACPI_S3;
 	fsp_memory_init(s3wake);
-	die("Get out from FSP memoryinit. \n");
+	if (postcar_frame_init(&pcf, 1 * KiB))
+		die("Unable to initialize postcar frame.\n");
+
+	/*
+	 * We need to make sure ramstage will be run cached. At this
+	 * point exact location of ramstage in cbmem is not known.
+	 * Instruct postcar to cache 16 megs under cbmem top which is
+	 * a safe bet to cover ramstage.
+	 */
+	top_of_ram = (uintptr_t) cbmem_top();
+	printk(BIOS_DEBUG, "top_of_ram = 0x%lx\n", top_of_ram);
+	top_of_ram -= 16*MiB;
+	postcar_frame_add_mtrr(&pcf, top_of_ram, 16*MiB, MTRR_TYPE_WRBACK);
+
+	/* Cache the ROM as WP just below 4GiB. */
+	postcar_frame_add_mtrr(&pcf, 0xFFFFFFFF - CONFIG_ROM_SIZE + 1,
+				CONFIG_ROM_SIZE, MTRR_TYPE_WRPROT);
+
+	run_postcar_phase(&pcf);
 }
 
 void platform_fsp_memory_init_params_cb(FSPM_UPD *mupd, uint32_t version)

src/soc/intel/cannonlake/uart.c

@@ -13,6 +13,8 @@
  * GNU General Public License for more details.
  */
 
+#define __SIMPLE_DEVICE__
+
 #include <assert.h>
 #include <console/uart.h>
 #include <device/pci_def.h>
@@ -60,8 +62,10 @@ void pch_uart_init(void)
 	gpio_configure_pads(p->pads, ARRAY_SIZE(p->pads));
 }
 
+#if IS_ENABLED(CONFIG_DRIVERS_UART_8250MEM)
 uintptr_t uart_platform_base(int idx)
 {
 	/* We can only have one serial console at a time */
 	return UART_DEBUG_BASE_ADDRESS;
 }
+#endif