spi: fix erase in SMM while SPIBAR is locked
The handling of write enable was not entirely correct, the opcode needs to be skipped when the controller is locked down. Addresses were not getting set properly for erase commands which seemed to mostly work when the previous command had set an address. Tested by adding events to the event log at runtime on a freslhy flashed device (with locked down SPI controller) until the log log shrink happens to ensure it does not hang: hexdump -C elog.event.kernel_clean 00000000 01 00 00 00 ad de 00 00 00 00 for x in $(seq 1 232); do cat elog.event.kernel_clean > /sys/firmware/gsmi/append_to_eventlog done mosys eventlog list | tail -6 154 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown 155 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown 156 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown 157 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown 158 | 2012-09-01 13:54:43 | Log area cleared | 1030 159 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown Change-Id: I3a50dae54422a9ff37daefce3632f8bcbe4eb89f Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1717 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit is contained in:
parent
00ba25decb
commit
3beb6db6dd
|
@ -627,13 +627,14 @@ int spi_xfer(struct spi_slave *slave, const void *dout,
|
||||||
if ((with_address = spi_setup_offset(&trans)) < 0)
|
if ((with_address = spi_setup_offset(&trans)) < 0)
|
||||||
return -1;
|
return -1;
|
||||||
|
|
||||||
if (!ichspi_lock && trans.opcode == SPI_OPCODE_WREN) {
|
if (trans.opcode == SPI_OPCODE_WREN) {
|
||||||
/*
|
/*
|
||||||
* Treat Write Enable as Atomic Pre-Op if possible
|
* Treat Write Enable as Atomic Pre-Op if possible
|
||||||
* in order to prevent the Management Engine from
|
* in order to prevent the Management Engine from
|
||||||
* issuing a transaction between WREN and DATA.
|
* issuing a transaction between WREN and DATA.
|
||||||
*/
|
*/
|
||||||
writew_(trans.opcode, cntlr.preop);
|
if (!ichspi_lock)
|
||||||
|
writew_(trans.opcode, cntlr.preop);
|
||||||
return 0;
|
return 0;
|
||||||
}
|
}
|
||||||
|
|
||||||
|
@ -645,6 +646,10 @@ int spi_xfer(struct spi_slave *slave, const void *dout,
|
||||||
control |= SPIC_ACS;
|
control |= SPIC_ACS;
|
||||||
|
|
||||||
if (!trans.bytesout && !trans.bytesin) {
|
if (!trans.bytesout && !trans.bytesin) {
|
||||||
|
/* SPI addresses are 24 bit only */
|
||||||
|
if (with_address)
|
||||||
|
writel_(trans.offset & 0x00FFFFFF, cntlr.addr);
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* This is a 'no data' command (like Write Enable), its
|
* This is a 'no data' command (like Write Enable), its
|
||||||
* bitesout size was 1, decremented to zero while executing
|
* bitesout size was 1, decremented to zero while executing
|
||||||
|
|
Loading…
Reference in New Issue