chrome ec: Update EC header from EC repository

- Updated ec_commands.h is copied in directly from EC repo
- Removed "old" interface and update resources for "new" interface
- Updated temp sensor constants and added "not calibrated"
- Update mainboards to remove check for EC_SWITCH_KEYBOARD_RECOVERY

Change-Id: Ic93c1914f86b6f5bc224178270624ed92b5c1e15
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/3743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>

src/ec/google/chromeec/acpi/ec.asl

@@ -29,9 +29,10 @@ Device (EC0)
 	Name (_UID, 1)
 	Name (_GPE, EC_SCI_GPI)
 	Name (TOFS, EC_TEMP_SENSOR_OFFSET)
-	Name (TNOP, 0xFD)	// Thermal sensor has no power
+	Name (TNCA, EC_TEMP_SENSOR_NOT_CALIBRATED)
-	Name (TBAD, 0xFE)	// Thermal sensor bad reading
+	Name (TNOP, EC_TEMP_SENSOR_NOT_POWERED)
-	Name (TNPR, 0xFF)	// Thermal sensor not present
+	Name (TBAD, EC_TEMP_SENSOR_ERROR)
+	Name (TNPR, EC_TEMP_SENSOR_NOT_PRESENT)
 	Name (DWRN, 15)		// Battery capacity warning at 15%
 	Name (DLOW, 10)		// Battery capacity low at 10%
 

src/ec/google/chromeec/acpi/superio.asl

@@ -29,8 +29,8 @@
  * SIO_EC_HOST_ENABLE       : Enable EC host command interface resources
  * EC_LPC_ADDR_HOST_DATA    : EC host command interface data port
  * EC_LPC_ADDR_HOST_CMD     : EC host command interface command port
- * EC_LPC_ADDR_OLD_PARAM    : EC host command parameter range base (old)
+ * EC_LPC_ADDR_HOST_ARGS    : EC host command arguments
- * EC_OLD_PARAM_SIZE        : Parameter buffer size (old)
+ * EC_LPC_ADDR_HOST_PARAM   : EC host command parameter buffer
  */
 
 // Scope is \_SB.PCI0.LPCB
@@ -75,8 +75,9 @@ Device (SIO) {
 		{
 			FixedIO (EC_LPC_ADDR_HOST_DATA, 1)
 			FixedIO (EC_LPC_ADDR_HOST_CMD, 1)
-			FixedIO (EC_LPC_ADDR_OLD_PARAM,
+			FixedIO (EC_LPC_ADDR_HOST_ARGS, 4)
-				 EC_OLD_PARAM_SIZE)
+			FixedIO (EC_LPC_ADDR_HOST_PARAM,
+				 EC_HOST_PARAM_SIZE)
 		})
 
 		Name (_PRS, ResourceTemplate ()
@@ -84,8 +85,9 @@ Device (SIO) {
 			StartDependentFn (0, 0) {
 				FixedIO (EC_LPC_ADDR_HOST_DATA, 1)
 				FixedIO (EC_LPC_ADDR_HOST_CMD, 1)
-				FixedIO (EC_LPC_ADDR_OLD_PARAM,
+				FixedIO (EC_LPC_ADDR_HOST_ARGS, 4)
-					 EC_OLD_PARAM_SIZE)
+				FixedIO (EC_LPC_ADDR_HOST_PARAM,
+					 EC_HOST_PARAM_SIZE)
 			}
 			EndDependentFn ()
 		})

src/ec/google/chromeec/ec_commands.h

@@ -1,4 +1,4 @@
-/* Copyright (c) 2012 The Chromium OS Authors. All rights reserved.
+/* Copyright (c) 2013 The Chromium OS Authors. All rights reserved.
  * Use of this source code is governed by a BSD-style license that can be
  * found in the LICENSE file.
  */
@@ -46,10 +46,6 @@
 #define EC_LPC_ADDR_HOST_PARAM 0x804
 #define EC_HOST_PARAM_SIZE     0x0fc  /* Size of param area in bytes */
 
-/* I/O addresses for host command params, old interface */
-#define EC_LPC_ADDR_OLD_PARAM  0x880
-#define EC_OLD_PARAM_SIZE      0x080  /* Size of param area in bytes */
-
 /* EC command register bit functions */
 #define EC_LPC_CMDR_DATA	(1 << 0)  /* Data ready for host to read */
 #define EC_LPC_CMDR_PENDING	(1 << 1)  /* Write pending to EC */
@@ -96,10 +92,11 @@
  *
  * Valid only if EC_MEMMAP_THERMAL_VERSION returns >= 2.
  */
-#define EC_TEMP_SENSOR_B_ENTRIES   8
+#define EC_TEMP_SENSOR_B_ENTRIES      8
-#define EC_TEMP_SENSOR_NOT_PRESENT 0xff
+#define EC_TEMP_SENSOR_NOT_PRESENT    0xff
-#define EC_TEMP_SENSOR_ERROR       0xfe
+#define EC_TEMP_SENSOR_ERROR          0xfe
-#define EC_TEMP_SENSOR_NOT_POWERED 0xfd
+#define EC_TEMP_SENSOR_NOT_POWERED    0xfd
+#define EC_TEMP_SENSOR_NOT_CALIBRATED 0xfc
 /*
  * The offset of temperature value stored in mapped memory.  This allows
  * reporting a temperature range of 200K to 454K = -73C to 181C.
@@ -121,8 +118,8 @@
 #define EC_SWITCH_LID_OPEN               0x01
 #define EC_SWITCH_POWER_BUTTON_PRESSED   0x02
 #define EC_SWITCH_WRITE_PROTECT_DISABLED 0x04
-/* Recovery requested via keyboard */
+/* Was recovery requested via keyboard; now unused. */
-#define EC_SWITCH_KEYBOARD_RECOVERY      0x08
+#define EC_SWITCH_IGNORE1		 0x08
 /* Recovery requested via dedicated signal (from servo board) */
 #define EC_SWITCH_DEDICATED_RECOVERY     0x10
 /* Was fake developer mode switch; now unused.  Remove in next refactor. */
@@ -135,6 +132,7 @@
 /* Wireless switch flags */
 #define EC_WIRELESS_SWITCH_WLAN      0x01
 #define EC_WIRELESS_SWITCH_BLUETOOTH 0x02
+#define EC_WIRELESS_SWITCH_WWAN      0x04
 
 /*
  * This header file is used in coreboot both in C and ACPI code.  The ACPI code
@@ -186,6 +184,10 @@ enum ec_status {
 	EC_RES_INVALID_RESPONSE = 5,
 	EC_RES_INVALID_VERSION = 6,
 	EC_RES_INVALID_CHECKSUM = 7,
+	EC_RES_IN_PROGRESS = 8,		/* Accepted, command in progress */
+	EC_RES_UNAVAILABLE = 9,		/* No response available */
+	EC_RES_TIMEOUT = 10,		/* We got a timeout */
+	EC_RES_OVERFLOW = 11,		/* Table / data overflow */
 };
 
 /*
@@ -388,6 +390,25 @@ struct ec_response_get_cmd_versions {
 	uint32_t version_mask;
 } __packed;
 
+/*
+ * Check EC communcations status (busy). This is needed on i2c/spi but not
+ * on lpc since it has its own out-of-band busy indicator.
+ *
+ * lpc must read the status from the command register. Attempting this on
+ * lpc will overwrite the args/parameter space and corrupt its data.
+ */
+#define EC_CMD_GET_COMMS_STATUS		0x09
+
+/* Avoid using ec_status which is for return values */
+enum ec_comms_status {
+	EC_COMMS_STATUS_PROCESSING	= 1 << 0,	/* Processing cmd */
+};
+
+struct ec_response_get_comms_status {
+	uint32_t flags;		/* Mask of enum ec_comms_status */
+} __packed;
+
+
 /*****************************************************************************/
 /* Flash commands */
 
@@ -468,8 +489,8 @@ struct ec_params_flash_erase {
  * be changed.
  */
 #define EC_FLASH_PROTECT_RO_NOW             (1 << 1)
-/* RW flash code protected now, until reboot. */
+/* Entire flash code protected now, until reboot. */
-#define EC_FLASH_PROTECT_RW_NOW             (1 << 2)
+#define EC_FLASH_PROTECT_ALL_NOW            (1 << 2)
 /* Flash write protect GPIO is asserted now */
 #define EC_FLASH_PROTECT_GPIO_ASSERTED      (1 << 3)
 /* Error - at least one bank of flash is stuck locked, and cannot be unlocked */
@@ -480,8 +501,8 @@ struct ec_params_flash_erase {
  * re-requesting the desired flags, or by a hard reset if that fails.
  */
 #define EC_FLASH_PROTECT_ERROR_INCONSISTENT (1 << 5)
-/* RW flash code protected when the EC boots */
+/* Entile flash code protected when the EC boots */
-#define EC_FLASH_PROTECT_RW_AT_BOOT         (1 << 6)
+#define EC_FLASH_PROTECT_ALL_AT_BOOT        (1 << 6)
 
 struct ec_params_flash_protect {
 	uint32_t mask;   /* Bits in flags to apply */
@@ -531,6 +552,24 @@ struct ec_response_flash_region_info {
 	uint32_t size;
 } __packed;
 
+/* Read/write VbNvContext */
+#define EC_CMD_VBNV_CONTEXT 0x17
+#define EC_VER_VBNV_CONTEXT 1
+#define EC_VBNV_BLOCK_SIZE 16
+
+enum ec_vbnvcontext_op {
+	EC_VBNV_CONTEXT_OP_READ,
+	EC_VBNV_CONTEXT_OP_WRITE,
+};
+
+struct ec_params_vbnvcontext {
+	uint32_t op;
+	uint8_t block[EC_VBNV_BLOCK_SIZE];
+} __packed;
+
+struct ec_response_vbnvcontext {
+	uint8_t block[EC_VBNV_BLOCK_SIZE];
+} __packed;
 
 /*****************************************************************************/
 /* PWM commands */
@@ -573,52 +612,131 @@ struct ec_params_pwm_set_fan_duty {
 
 /*****************************************************************************/
 /*
- * Lightbar commands. This looks worse than it is. Since we only use one LPC
+ * Lightbar commands. This looks worse than it is. Since we only use one HOST
  * command to say "talk to the lightbar", we put the "and tell it to do X" part
  * into a subcommand. We'll make separate structs for subcommands with
  * different input args, so that we know how much to expect.
  */
 #define EC_CMD_LIGHTBAR_CMD 0x28
 
-struct ec_params_lightbar_cmd {
+struct rgb_s {
-	union {
+	uint8_t r, g, b;
-		union {
+};
-			uint8_t cmd;
-			struct {
-				uint8_t cmd;
-			} dump, off, on, init, get_seq;
-			struct num {
-				uint8_t cmd;
-				uint8_t num;
-			} brightness, seq;
 
-			struct reg {
+#define LB_BATTERY_LEVELS 4
-				uint8_t cmd;
+/* List of tweakable parameters. NOTE: It's __packed so it can be sent in a
-				uint8_t ctrl, reg, value;
+ * host command, but the alignment is the same regardless. Keep it that way.
-			} reg;
+ */
-			struct rgb {
+struct lightbar_params {
-				uint8_t cmd;
+	/* Timing */
-				uint8_t led, red, green, blue;
+	int google_ramp_up;
-			} rgb;
+	int google_ramp_down;
-		} in;
+	int s3s0_ramp_up;
-		union {
+	int s0_tick_delay[2];			/* AC=0/1 */
-			struct dump {
+	int s0a_tick_delay[2];			/* AC=0/1 */
-				struct {
+	int s0s3_ramp_down;
-					uint8_t reg;
+	int s3_sleep_for;
-					uint8_t ic0;
+	int s3_ramp_up;
-					uint8_t ic1;
+	int s3_ramp_down;
-				} vals[23];
+
-			} dump;
+	/* Oscillation */
-			struct get_seq {
+	uint8_t new_s0;
-				uint8_t num;
+	uint8_t osc_min[2];			/* AC=0/1 */
-			} get_seq;
+	uint8_t osc_max[2];			/* AC=0/1 */
-			struct {
+	uint8_t w_ofs[2];			/* AC=0/1 */
-				/* no return params */
+
-			} off, on, init, brightness, seq, reg, rgb;
+	/* Brightness limits based on the backlight and AC. */
-		} out;
+	uint8_t bright_bl_off_fixed[2];		/* AC=0/1 */
+	uint8_t bright_bl_on_min[2];		/* AC=0/1 */
+	uint8_t bright_bl_on_max[2];		/* AC=0/1 */
+
+	/* Battery level thresholds */
+	uint8_t battery_threshold[LB_BATTERY_LEVELS - 1];
+
+	/* Map [AC][battery_level] to color index */
+	uint8_t s0_idx[2][LB_BATTERY_LEVELS];	/* AP is running */
+	uint8_t s3_idx[2][LB_BATTERY_LEVELS];	/* AP is sleeping */
+
+	/* Color palette */
+	struct rgb_s color[8];			/* 0-3 are Google colors */
+} __packed;
+
+struct ec_params_lightbar {
+	uint8_t cmd;		      /* Command (see enum lightbar_command) */
+	union {
+		struct {
+			/* no args */
+		} dump, off, on, init, get_seq, get_params;
+
+		struct num {
+			uint8_t num;
+		} brightness, seq, demo;
+
+		struct reg {
+			uint8_t ctrl, reg, value;
+		} reg;
+
+		struct rgb {
+			uint8_t led, red, green, blue;
+		} rgb;
+
+		struct lightbar_params set_params;
 	};
 } __packed;
 
+struct ec_response_lightbar {
+	union {
+		struct dump {
+			struct {
+				uint8_t reg;
+				uint8_t ic0;
+				uint8_t ic1;
+			} vals[23];
+		} dump;
+
+		struct get_seq {
+			uint8_t num;
+		} get_seq;
+
+		struct lightbar_params get_params;
+
+		struct {
+			/* no return params */
+		} off, on, init, brightness, seq, reg, rgb, demo, set_params;
+	};
+} __packed;
+
+/* Lightbar commands */
+enum lightbar_command {
+	LIGHTBAR_CMD_DUMP = 0,
+	LIGHTBAR_CMD_OFF = 1,
+	LIGHTBAR_CMD_ON = 2,
+	LIGHTBAR_CMD_INIT = 3,
+	LIGHTBAR_CMD_BRIGHTNESS = 4,
+	LIGHTBAR_CMD_SEQ = 5,
+	LIGHTBAR_CMD_REG = 6,
+	LIGHTBAR_CMD_RGB = 7,
+	LIGHTBAR_CMD_GET_SEQ = 8,
+	LIGHTBAR_CMD_DEMO = 9,
+	LIGHTBAR_CMD_GET_PARAMS = 10,
+	LIGHTBAR_CMD_SET_PARAMS = 11,
+	LIGHTBAR_NUM_CMDS
+};
+
+/*****************************************************************************/
+/* LED control commands */
+
+#define EC_CMD_LED_SET 0x29
+
+#define EC_LED_FLAGS_AUTO (1 << 1)
+
+struct ec_params_led_set {
+	uint8_t r;
+	uint8_t g;
+	uint8_t b; /* Used as yellow if there is no blue LED */
+	uint8_t flags;
+} __packed;
+
 /*****************************************************************************/
 /* Verified boot commands */
 
@@ -651,22 +769,30 @@ struct ec_response_vboot_hash {
 } __packed;
 
 enum ec_vboot_hash_cmd {
-	EC_VBOOT_HASH_GET,     /* Get current hash status */
+	EC_VBOOT_HASH_GET = 0,       /* Get current hash status */
-	EC_VBOOT_HASH_ABORT,   /* Abort calculating current hash */
+	EC_VBOOT_HASH_ABORT = 1,     /* Abort calculating current hash */
-	EC_VBOOT_HASH_START,   /* Start computing a new hash */
+	EC_VBOOT_HASH_START = 2,     /* Start computing a new hash */
-	EC_VBOOT_HASH_RECALC,  /* Synchronously compute a new hash */
+	EC_VBOOT_HASH_RECALC = 3,    /* Synchronously compute a new hash */
 };
 
 enum ec_vboot_hash_type {
-	EC_VBOOT_HASH_TYPE_SHA256,  /* SHA-256 */
+	EC_VBOOT_HASH_TYPE_SHA256 = 0, /* SHA-256 */
 };
 
 enum ec_vboot_hash_status {
-	EC_VBOOT_HASH_STATUS_NONE,     /* No hash (not started, or aborted) */
+	EC_VBOOT_HASH_STATUS_NONE = 0, /* No hash (not started, or aborted) */
-	EC_VBOOT_HASH_STATUS_DONE,     /* Finished computing a hash */
+	EC_VBOOT_HASH_STATUS_DONE = 1, /* Finished computing a hash */
-	EC_VBOOT_HASH_STATUS_BUSY,     /* Busy computing a hash */
+	EC_VBOOT_HASH_STATUS_BUSY = 2, /* Busy computing a hash */
 };
 
+/*
+ * Special values for offset for EC_VBOOT_HASH_START and EC_VBOOT_HASH_RECALC.
+ * If one of these is specified, the EC will automatically update offset and
+ * size to the correct values for the specified image (RO or RW).
+ */
+#define EC_VBOOT_HASH_OFFSET_RO 0xfffffffe
+#define EC_VBOOT_HASH_OFFSET_RW 0xfffffffd
+
 /*****************************************************************************/
 /* USB charging control commands */
 
@@ -772,6 +898,32 @@ struct ec_response_thermal_get_threshold {
 /* Toggle automatic fan control */
 #define EC_CMD_THERMAL_AUTO_FAN_CTRL 0x52
 
+/* Get TMP006 calibration data */
+#define EC_CMD_TMP006_GET_CALIBRATION 0x53
+
+struct ec_params_tmp006_get_calibration {
+	uint8_t index;
+} __packed;
+
+struct ec_response_tmp006_get_calibration {
+	float s0;
+	float b0;
+	float b1;
+	float b2;
+} __packed;
+
+/* Set TMP006 calibration data */
+#define EC_CMD_TMP006_SET_CALIBRATION 0x54
+
+struct ec_params_tmp006_set_calibration {
+	uint8_t index;
+	uint8_t reserved[3];  /* Reserved; set 0 */
+	float s0;
+	float b0;
+	float b1;
+	float b2;
+} __packed;
+
 /*****************************************************************************/
 /* MKBP - Matrix KeyBoard Protocol */
 
@@ -801,6 +953,112 @@ struct ec_params_mkbp_simulate_key {
 	uint8_t pressed;
 } __packed;
 
+/* Configure keyboard scanning */
+#define EC_CMD_MKBP_SET_CONFIG 0x64
+#define EC_CMD_MKBP_GET_CONFIG 0x65
+
+/* flags */
+enum mkbp_config_flags {
+	EC_MKBP_FLAGS_ENABLE = 1,	/* Enable keyboard scanning */
+};
+
+enum mkbp_config_valid {
+	EC_MKBP_VALID_SCAN_PERIOD		= 1 << 0,
+	EC_MKBP_VALID_POLL_TIMEOUT		= 1 << 1,
+	EC_MKBP_VALID_MIN_POST_SCAN_DELAY	= 1 << 3,
+	EC_MKBP_VALID_OUTPUT_SETTLE		= 1 << 4,
+	EC_MKBP_VALID_DEBOUNCE_DOWN		= 1 << 5,
+	EC_MKBP_VALID_DEBOUNCE_UP		= 1 << 6,
+	EC_MKBP_VALID_FIFO_MAX_DEPTH		= 1 << 7,
+};
+
+/* Configuration for our key scanning algorithm */
+struct ec_mkbp_config {
+	uint32_t valid_mask;		/* valid fields */
+	uint8_t flags;		/* some flags (enum mkbp_config_flags) */
+	uint8_t valid_flags;		/* which flags are valid */
+	uint16_t scan_period_us;	/* period between start of scans */
+	/* revert to interrupt mode after no activity for this long */
+	uint32_t poll_timeout_us;
+	/*
+	 * minimum post-scan relax time. Once we finish a scan we check
+	 * the time until we are due to start the next one. If this time is
+	 * shorter this field, we use this instead.
+	 */
+	uint16_t min_post_scan_delay_us;
+	/* delay between setting up output and waiting for it to settle */
+	uint16_t output_settle_us;
+	uint16_t debounce_down_us;	/* time for debounce on key down */
+	uint16_t debounce_up_us;	/* time for debounce on key up */
+	/* maximum depth to allow for fifo (0 = no keyscan output) */
+	uint8_t fifo_max_depth;
+} __packed;
+
+struct ec_params_mkbp_set_config {
+	struct ec_mkbp_config config;
+} __packed;
+
+struct ec_response_mkbp_get_config {
+	struct ec_mkbp_config config;
+} __packed;
+
+/* Run the key scan emulation */
+#define EC_CMD_KEYSCAN_SEQ_CTRL 0x66
+
+enum ec_keyscan_seq_cmd {
+	EC_KEYSCAN_SEQ_STATUS = 0,	/* Get status information */
+	EC_KEYSCAN_SEQ_CLEAR = 1,	/* Clear sequence */
+	EC_KEYSCAN_SEQ_ADD = 2,		/* Add item to sequence */
+	EC_KEYSCAN_SEQ_START = 3,	/* Start running sequence */
+	EC_KEYSCAN_SEQ_COLLECT = 4,	/* Collect sequence summary data */
+};
+
+enum ec_collect_flags {
+	/*
+	 * Indicates this scan was processed by the EC. Due to timing, some
+	 * scans may be skipped.
+	 */
+	EC_KEYSCAN_SEQ_FLAG_DONE	= 1 << 0,
+};
+
+struct ec_collect_item {
+	uint8_t flags;		/* some flags (enum ec_collect_flags) */
+};
+
+struct ec_params_keyscan_seq_ctrl {
+	uint8_t cmd;	/* Command to send (enum ec_keyscan_seq_cmd) */
+	union {
+		struct {
+			uint8_t active;		/* still active */
+			uint8_t num_items;	/* number of items */
+			/* Current item being presented */
+			uint8_t cur_item;
+		} status;
+		struct {
+			/*
+			 * Absolute time for this scan, measured from the
+			 * start of the sequence.
+			 */
+			uint32_t time_us;
+			uint8_t scan[0];	/* keyscan data */
+		} add;
+		struct {
+			uint8_t start_item;	/* First item to return */
+			uint8_t num_items;	/* Number of items to return */
+		} collect;
+	};
+} __packed;
+
+struct ec_result_keyscan_seq_ctrl {
+	union {
+		struct {
+			uint8_t num_items;	/* Number of items */
+			/* Data for each item */
+			struct ec_collect_item item[0];
+		} collect;
+	};
+} __packed;
+
 /*****************************************************************************/
 /* Temperature sensor commands */
 
@@ -897,7 +1155,7 @@ struct ec_response_gpio_get {
 #define EC_CMD_I2C_READ 0x94
 
 struct ec_params_i2c_read {
-	uint16_t addr;
+	uint16_t addr; /* 8-bit address (7-bit shifted << 1) */
 	uint8_t read_size; /* Either 8 or 16. */
 	uint8_t port;
 	uint8_t offset;
@@ -911,7 +1169,7 @@ struct ec_response_i2c_read {
 
 struct ec_params_i2c_write {
 	uint16_t data;
-	uint16_t addr;
+	uint16_t addr; /* 8-bit address (7-bit shifted << 1) */
 	uint8_t write_size; /* Either 8 or 16. */
 	uint8_t port;
 	uint8_t offset;
@@ -941,6 +1199,177 @@ struct ec_params_force_idle {
  */
 #define EC_CMD_CONSOLE_READ 0x98
 
+/*****************************************************************************/
+
+/*
+ * Cut off battery power output if the battery supports.
+ *
+ * For unsupported battery, just don't implement this command and lets EC
+ * return EC_RES_INVALID_COMMAND.
+ */
+#define EC_CMD_BATTERY_CUT_OFF 0x99
+
+/*****************************************************************************/
+/* USB port mux control. */
+
+/*
+ * Switch USB mux or return to automatic switching.
+ */
+#define EC_CMD_USB_MUX 0x9a
+
+struct ec_params_usb_mux {
+	uint8_t mux;
+} __packed;
+
+/*****************************************************************************/
+/* LDOs / FETs control. */
+
+enum ec_ldo_state {
+	EC_LDO_STATE_OFF = 0,	/* the LDO / FET is shut down */
+	EC_LDO_STATE_ON = 1,	/* the LDO / FET is ON / providing power */
+};
+
+/*
+ * Switch on/off a LDO.
+ */
+#define EC_CMD_LDO_SET 0x9b
+
+struct ec_params_ldo_set {
+	uint8_t index;
+	uint8_t state;
+} __packed;
+
+/*
+ * Get LDO state.
+ */
+#define EC_CMD_LDO_GET 0x9c
+
+struct ec_params_ldo_get {
+	uint8_t index;
+} __packed;
+
+struct ec_response_ldo_get {
+	uint8_t state;
+} __packed;
+
+/*****************************************************************************/
+/* Power info. */
+
+/*
+ * Get power info.
+ */
+#define EC_CMD_POWER_INFO 0x9d
+
+struct ec_response_power_info {
+	uint32_t usb_dev_type;
+	uint16_t voltage_ac;
+	uint16_t voltage_system;
+	uint16_t current_system;
+	uint16_t usb_current_limit;
+} __packed;
+
+/*****************************************************************************/
+/* I2C passthru command */
+
+#define EC_CMD_I2C_PASSTHRU 0x9e
+
+/* Slave address is 10 (not 7) bit */
+#define EC_I2C_FLAG_10BIT	(1 << 16)
+
+/* Read data; if not present, message is a write */
+#define EC_I2C_FLAG_READ	(1 << 15)
+
+/* Mask for address */
+#define EC_I2C_ADDR_MASK	0x3ff
+
+#define EC_I2C_STATUS_NAK	(1 << 0) /* Transfer was not acknowledged */
+#define EC_I2C_STATUS_TIMEOUT	(1 << 1) /* Timeout during transfer */
+
+/* Any error */
+#define EC_I2C_STATUS_ERROR	(EC_I2C_STATUS_NAK | EC_I2C_STATUS_TIMEOUT)
+
+struct ec_params_i2c_passthru_msg {
+	uint16_t addr_flags;	/* I2C slave address (7 or 10 bits) and flags */
+	uint16_t len;		/* Number of bytes to read or write */
+} __packed;
+
+struct ec_params_i2c_passthru {
+	uint8_t port;		/* I2C port number */
+	uint8_t num_msgs;	/* Number of messages */
+	struct ec_params_i2c_passthru_msg msg[];
+	/* Data to write for all messages is concatenated here */
+} __packed;
+
+struct ec_response_i2c_passthru {
+	uint8_t i2c_status;	/* Status flags (EC_I2C_STATUS_...) */
+	uint8_t num_msgs;	/* Number of messages processed */
+	uint8_t data[];		/* Data read by messages concatenated here */
+} __packed;
+
+
+/*****************************************************************************/
+/* Temporary debug commands. TODO: remove this crosbug.com/p/13849 */
+
+/*
+ * Dump charge state machine context.
+ *
+ * Response is a binary dump of charge state machine context.
+ */
+#define EC_CMD_CHARGE_DUMP 0xa0
+
+/*
+ * Set maximum battery charging current.
+ */
+#define EC_CMD_CHARGE_CURRENT_LIMIT 0xa1
+
+struct ec_params_current_limit {
+	uint32_t limit; /* in mA */
+} __packed;
+
+/*
+ * Set maximum external power current.
+ */
+#define EC_CMD_EXT_POWER_CURRENT_LIMIT 0xa2
+
+struct ec_params_ext_power_current_limit {
+	uint32_t limit; /* in mA */
+} __packed;
+
+/*****************************************************************************/
+/* Smart battery pass-through */
+
+/* Get / Set 16-bit smart battery registers */
+#define EC_CMD_SB_READ_WORD   0xb0
+#define EC_CMD_SB_WRITE_WORD  0xb1
+
+/* Get / Set string smart battery parameters
+ * formatted as SMBUS "block".
+ */
+#define EC_CMD_SB_READ_BLOCK  0xb2
+#define EC_CMD_SB_WRITE_BLOCK 0xb3
+
+struct ec_params_sb_rd {
+	uint8_t reg;
+} __packed;
+
+struct ec_response_sb_rd_word {
+	uint16_t value;
+} __packed;
+
+struct ec_params_sb_wr_word {
+	uint8_t reg;
+	uint16_t value;
+} __packed;
+
+struct ec_response_sb_rd_block {
+	uint8_t data[32];
+} __packed;
+
+struct ec_params_sb_wr_block {
+	uint8_t reg;
+	uint16_t data[32];
+} __packed;
+
 /*****************************************************************************/
 /* System commands */
 
@@ -953,23 +1382,31 @@ struct ec_params_force_idle {
 /* Command */
 enum ec_reboot_cmd {
 	EC_REBOOT_CANCEL = 0,        /* Cancel a pending reboot */
-	EC_REBOOT_JUMP_RO,           /* Jump to RO without rebooting */
+	EC_REBOOT_JUMP_RO = 1,       /* Jump to RO without rebooting */
-	EC_REBOOT_JUMP_RW,           /* Jump to RW without rebooting */
+	EC_REBOOT_JUMP_RW = 2,       /* Jump to RW without rebooting */
 	/* (command 3 was jump to RW-B) */
 	EC_REBOOT_COLD = 4,          /* Cold-reboot */
-	EC_REBOOT_DISABLE_JUMP,      /* Disable jump until next reboot */
+	EC_REBOOT_DISABLE_JUMP = 5,  /* Disable jump until next reboot */
+	EC_REBOOT_HIBERNATE = 6      /* Hibernate EC */
 };
 
 /* Flags for ec_params_reboot_ec.reboot_flags */
 #define EC_REBOOT_FLAG_RESERVED0      (1 << 0)  /* Was recovery request */
-#define EC_REBOOT_FLAG_ON_AP_SHUTDOWN (1 << 1)
+#define EC_REBOOT_FLAG_ON_AP_SHUTDOWN (1 << 1)  /* Reboot after AP shutdown */
-#define EC_REBOOT_FLAG_POWER_ON       (1 << 2)
 
 struct ec_params_reboot_ec {
 	uint8_t cmd;           /* enum ec_reboot_cmd */
 	uint8_t flags;         /* See EC_REBOOT_FLAG_* */
 } __packed;
 
+/*
+ * Get information on last EC panic.
+ *
+ * Returns variable-length platform-dependent panic information.  See panic.h
+ * for details.
+ */
+#define EC_CMD_GET_PANIC_INFO 0xd3
+
 /*****************************************************************************/
 /*
  * ACPI commands
@@ -1052,6 +1489,15 @@ struct ec_params_reboot_ec {
  */
 #define EC_CMD_REBOOT 0xd1  /* Think "die" */
 
+/*
+ * Resend last response (not supported on LPC).
+ *
+ * Returns EC_RES_UNAVAILABLE if there is no response available - for example,
+ * there was no previous command, or the previous command's response was too
+ * big to save.
+ */
+#define EC_CMD_RESEND_RESPONSE 0xdb
+
 /*
  * This header byte on a command indicate version 0. Any header byte less
  * than this means that we are talking to an old EC which doesn't support

src/ec/google/chromeec/ec_lpc.c

@@ -50,52 +50,6 @@ static int google_chromeec_wait_ready(u16 port)
 	return 0;
 }
 
-static int google_chromeec_cmd_args_supported(void)
-{
-	if (inb(EC_LPC_ADDR_MEMMAP + EC_MEMMAP_ID) == 'E' &&
-	    inb(EC_LPC_ADDR_MEMMAP + EC_MEMMAP_ID + 1) == 'C' &&
-	    (inb(EC_LPC_ADDR_MEMMAP + EC_MEMMAP_HOST_CMD_FLAGS) &
-	     EC_HOST_CMD_FLAG_LPC_ARGS_SUPPORTED))
-		return 1;
-
-	return 0;
-}
-
-static int google_chromeec_command_old(struct chromeec_command *cec_command)
-{
-	int i;
-
-	if (cec_command->cmd_version) {
-		printk(BIOS_ERR, "Invalid version for command protocol!\n");
-		return 1;
-	}
-
-	if (google_chromeec_wait_ready(EC_LPC_ADDR_HOST_CMD)) {
-		printk(BIOS_ERR, "Timeout waiting for EC ready!\n");
-		return 1;
-	}
-
-	/* Copy command data, if any. */
-	for (i = 0; i < cec_command->cmd_size_in; i++)
-		outb(((char*)cec_command->cmd_data_in)[i],
-		     EC_LPC_ADDR_OLD_PARAM + i);
-
-	/* Issue the command. */
-	outb(cec_command->cmd_code, EC_LPC_ADDR_HOST_CMD);
-
-	if (google_chromeec_wait_ready(EC_LPC_ADDR_HOST_CMD)) {
-		printk(BIOS_ERR, "Timeout waiting for EC process command %d!\n",
-		       cec_command->cmd_code);
-		return 1;
-	}
-
-	for (i = 0; i < cec_command->cmd_size_out; i++)
-		((char*)cec_command->cmd_data_out)[i] =
-			inb(EC_LPC_ADDR_OLD_PARAM + i);
-	cec_command->cmd_code = inb(EC_LPC_ADDR_HOST_DATA);
-	return 0;
-}
-
 int google_chromeec_command(struct chromeec_command *cec_command)
 {
 	struct ec_lpc_host_args args;
@@ -105,10 +59,6 @@ int google_chromeec_command(struct chromeec_command *cec_command)
 	int csum;
 	int i;
 
-	/* Fall back to old command protocol if necessary */
-	if (!google_chromeec_cmd_args_supported())
-		return google_chromeec_command_old(cec_command);
-
 	/* Fill in args */
 	args.flags = EC_HOST_ARGS_FLAG_FROM_HOST;
 	args.command_version = cec_command->cmd_version;

src/mainboard/google/link/acpi/thermal.asl

@@ -48,6 +48,11 @@ Scope (\_TZ)
 			// Get CPU Temperature from TIN9/PECI via EC
 			Store (\_SB.PCI0.LPCB.EC0.TIN9, Local0)
 
+			// Check for sensor not calibrated
+			If (LEqual (Local0, \_SB.PCI0.LPCB.EC0.TNCA)) {
+				Return (CTOK(0))
+			}
+
 			// Check for sensor not present
 			If (LEqual (Local0, \_SB.PCI0.LPCB.EC0.TNPR)) {
 				Return (CTOK(0))

src/mainboard/google/link/chromeos.c

@@ -107,8 +107,7 @@ int get_recovery_mode_switch(void)
 	u32 ec_events;
 
 	/* If a switch is set, we don't need to look at events. */
-	if (ec_switches & (EC_SWITCH_KEYBOARD_RECOVERY |
+	if (ec_switches & (EC_SWITCH_DEDICATED_RECOVERY))
-			   EC_SWITCH_DEDICATED_RECOVERY))
 		return 1;
 
 	/* Else check if the EC has posted the keyboard recovery event. */