mb/google/hatch/vr/puff: Add psys_pmax calculation
This patch adds psys_pmax calculation. There are two types of power sources. One is barrel jack and the other is USB TYPE-C. The voltage level is fixed for a barrel jack while TYPE-C may vary depending on power ratings. We need to get voltage information from EC and calculate correct psys_pmax value. The psys_pmax needs to be set before FSP-S since FSP-S will handle the setting passing to pcode, so move the routine ahead to variant_ramstage_init. BUG=b:151972149 TEST=emerge-puff coreboot chromeos-bootimage check firmware log and ensure psys_pmax is passed to FSP check the data from dump_intel_rapl_consumption in the OS and ensure the power data is close to an external power meter. Change-Id: Iff767d4b44a01e766258345545438a54a16d1af5 Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40828 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
This commit is contained in:
parent
52e56e8479
commit
4c7bc8db74
|
@ -31,23 +31,6 @@ static void wait_for_hpd(gpio_t gpio, long timeout)
|
|||
stopwatch_duration_msecs(&sw));
|
||||
}
|
||||
|
||||
void variant_ramstage_init(void)
|
||||
{
|
||||
static const long display_timeout_ms = 3000;
|
||||
|
||||
/* This is reconfigured back to whatever FSP-S expects by
|
||||
gpio_configure_pads. */
|
||||
gpio_input(GPIO_HDMI_HPD);
|
||||
gpio_input(GPIO_DP_HPD);
|
||||
if (display_init_required()
|
||||
&& !gpio_get(GPIO_HDMI_HPD)
|
||||
&& !gpio_get(GPIO_DP_HPD)) {
|
||||
/* This has to be done before FSP-S runs. */
|
||||
if (google_chromeec_wait_for_displayport(display_timeout_ms))
|
||||
wait_for_hpd(GPIO_DP_HPD, display_timeout_ms);
|
||||
}
|
||||
}
|
||||
|
||||
/*
|
||||
* For type-C chargers, set PL2 to 90% of max power to account for
|
||||
* cable loss and FET Rdson loss in the path from the source.
|
||||
|
@ -86,6 +69,24 @@ void variant_ramstage_init(void)
|
|||
* | n (U22) | 29 | .9n | .9n | x(43) |
|
||||
* +-------------+-----+---------+---------+-------+
|
||||
*/
|
||||
|
||||
/*
|
||||
* Psys_pmax considerations
|
||||
*
|
||||
* Given the hardware design in puff, the serial shunt resistor is 0.01ohm.
|
||||
* The full scale of hardware PSYS signal 0.8v maps to system current 9.6A
|
||||
* instead of real system power. The equation is shown below:
|
||||
* PSYS = 0.8v = (0.01ohm x Iinput) x 50 (INA213, gain 50V/V) x 15k/(15k + 75k)
|
||||
* Hence, Iinput (Amps) = 9.6A
|
||||
* Since there is no voltage information from PSYS, different voltage input
|
||||
* would map to different Psys_pmax settings:
|
||||
* For Type-C 15V, the Psys_pmax sholud be 15v x 9.6A = 144W
|
||||
* For Type-C 20V, the Psys_pmax should be 20v x 9.6A = 192W
|
||||
* For a barral jack, the Psys_pmax should be 19v x 9.6A = 182.4W
|
||||
*/
|
||||
#define PSYS_IMAX 9600
|
||||
#define BJ_VOLTS_MV 19000
|
||||
|
||||
static void mainboard_set_power_limits(config_t *conf)
|
||||
{
|
||||
enum usb_chg_type type;
|
||||
|
@ -108,15 +109,33 @@ static void mainboard_set_power_limits(config_t *conf)
|
|||
/* set minimum duty cycle */
|
||||
conf->tdp_psyspl3_dutycycle = PUFF_MIN_DUTYCYCLE;
|
||||
conf->tdp_pl4 = SET_PSYSPL2(psyspl2);
|
||||
} else {
|
||||
/* Input type is barrel jack */
|
||||
volts_mv = BJ_VOLTS_MV;
|
||||
}
|
||||
/* voltage unit is milliVolts and current is in milliAmps */
|
||||
conf->psys_pmax = (u16)(((u32)PSYS_IMAX * volts_mv) / 1000000);
|
||||
|
||||
conf->tdp_pl2_override = PUFF_PL2;
|
||||
/* set psyspl2 to 90% of max adapter power */
|
||||
conf->tdp_psyspl2 = SET_PSYSPL2(psyspl2);
|
||||
}
|
||||
|
||||
void variant_mainboard_enable(struct device *dev)
|
||||
void variant_ramstage_init(void)
|
||||
{
|
||||
static const long display_timeout_ms = 3000;
|
||||
config_t *conf = config_of_soc();
|
||||
|
||||
/* This is reconfigured back to whatever FSP-S expects by gpio_configure_pads. */
|
||||
gpio_input(GPIO_HDMI_HPD);
|
||||
gpio_input(GPIO_DP_HPD);
|
||||
if (display_init_required()
|
||||
&& !gpio_get(GPIO_HDMI_HPD)
|
||||
&& !gpio_get(GPIO_DP_HPD)) {
|
||||
/* This has to be done before FSP-S runs. */
|
||||
if (google_chromeec_wait_for_displayport(display_timeout_ms))
|
||||
wait_for_hpd(GPIO_DP_HPD, display_timeout_ms);
|
||||
}
|
||||
/* Psys_pmax needs to be setup before FSP-S */
|
||||
mainboard_set_power_limits(conf);
|
||||
}
|
||||
|
|
|
@ -31,23 +31,6 @@ static void wait_for_hpd(gpio_t gpio, long timeout)
|
|||
stopwatch_duration_msecs(&sw));
|
||||
}
|
||||
|
||||
void variant_ramstage_init(void)
|
||||
{
|
||||
static const long display_timeout_ms = 3000;
|
||||
|
||||
/* This is reconfigured back to whatever FSP-S expects by
|
||||
gpio_configure_pads. */
|
||||
gpio_input(GPIO_HDMI_HPD);
|
||||
gpio_input(GPIO_DP_HPD);
|
||||
if (display_init_required()
|
||||
&& !gpio_get(GPIO_HDMI_HPD)
|
||||
&& !gpio_get(GPIO_DP_HPD)) {
|
||||
/* This has to be done before FSP-S runs. */
|
||||
if (google_chromeec_wait_for_displayport(display_timeout_ms))
|
||||
wait_for_hpd(GPIO_DP_HPD, display_timeout_ms);
|
||||
}
|
||||
}
|
||||
|
||||
/*
|
||||
* For type-C chargers, set PL2 to 90% of max power to account for
|
||||
* cable loss and FET Rdson loss in the path from the source.
|
||||
|
@ -86,6 +69,24 @@ void variant_ramstage_init(void)
|
|||
* | n (U22) | 29 | .9n | .9n | x(43) |
|
||||
* +-------------+-----+---------+---------+-------+
|
||||
*/
|
||||
|
||||
/*
|
||||
* Psys_pmax considerations
|
||||
*
|
||||
* Given the hardware design in puff, the serial shunt resistor is 0.01ohm.
|
||||
* The full scale of hardware PSYS signal 0.8v maps to system current 9.6A
|
||||
* instead of real system power. The equation is shown below:
|
||||
* PSYS = 0.8v = (0.01ohm x Iinput) x 50 (INA213, gain 50V/V) x 15k/(15k + 75k)
|
||||
* Hence, Iinput (Amps) = 9.6A
|
||||
* Since there is no voltage information from PSYS, different voltage input
|
||||
* would map to different Psys_pmax settings:
|
||||
* For Type-C 15V, the Psys_pmax sholud be 15v x 9.6A = 144W
|
||||
* For Type-C 20V, the Psys_pmax should be 20v x 9.6A = 192W
|
||||
* For a barral jack, the Psys_pmax should be 19v x 9.6A = 182.4W
|
||||
*/
|
||||
#define PSYS_IMAX 9600
|
||||
#define BJ_VOLTS_MV 19000
|
||||
|
||||
static void mainboard_set_power_limits(config_t *conf)
|
||||
{
|
||||
enum usb_chg_type type;
|
||||
|
@ -108,15 +109,33 @@ static void mainboard_set_power_limits(config_t *conf)
|
|||
/* set minimum duty cycle */
|
||||
conf->tdp_psyspl3_dutycycle = PUFF_MIN_DUTYCYCLE;
|
||||
conf->tdp_pl4 = SET_PSYSPL2(psyspl2);
|
||||
} else {
|
||||
/* Input type is barrel jack */
|
||||
volts_mv = BJ_VOLTS_MV;
|
||||
}
|
||||
/* voltage unit is milliVolts and current is in milliAmps */
|
||||
conf->psys_pmax = (u16)(((u32)PSYS_IMAX * volts_mv) / 1000000);
|
||||
|
||||
conf->tdp_pl2_override = PUFF_PL2;
|
||||
/* set psyspl2 to 90% of max adapter power */
|
||||
conf->tdp_psyspl2 = SET_PSYSPL2(psyspl2);
|
||||
}
|
||||
|
||||
void variant_mainboard_enable(struct device *dev)
|
||||
void variant_ramstage_init(void)
|
||||
{
|
||||
static const long display_timeout_ms = 3000;
|
||||
config_t *conf = config_of_soc();
|
||||
|
||||
/* This is reconfigured back to whatever FSP-S expects by gpio_configure_pads. */
|
||||
gpio_input(GPIO_HDMI_HPD);
|
||||
gpio_input(GPIO_DP_HPD);
|
||||
if (display_init_required()
|
||||
&& !gpio_get(GPIO_HDMI_HPD)
|
||||
&& !gpio_get(GPIO_DP_HPD)) {
|
||||
/* This has to be done before FSP-S runs. */
|
||||
if (google_chromeec_wait_for_displayport(display_timeout_ms))
|
||||
wait_for_hpd(GPIO_DP_HPD, display_timeout_ms);
|
||||
}
|
||||
/* Psys_pmax needs to be setup before FSP-S */
|
||||
mainboard_set_power_limits(conf);
|
||||
}
|
||||
|
|
Loading…
Reference in New Issue