diff --git a/src/mainboard/amd/quartet/Config.lb b/src/mainboard/amd/quartet/Config.lb
index b6d65b4cb5..a358c25841 100644
--- a/src/mainboard/amd/quartet/Config.lb
+++ b/src/mainboard/amd/quartet/Config.lb
@@ -1,36 +1,180 @@
 uses HAVE_MP_TABLE
 uses HAVE_PIRQ_TABLE
 uses USE_FALLBACK_IMAGE
-#
-#
+uses MAINBOARD
+uses ARCH
+uses FALLBACK_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+
 ###
-### Set all of the defaults for an x86 architecture
+### Build options
 ###
-#
-#
+
+##
+## Build code for the fallback boot
+##
+option HAVE_FALLBACK_BOOT=1
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+option HAVE_HARD_RESET=1
+
+##
+## Build code to export a programmable irq routing table
+##
+option HAVE_PIRQ_TABLE=1
+option IRQ_SLOT_COUNT=7
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+option HAVE_MP_TABLE=1
+
+##
+## Build code to export a CMOS option table
+##
+option HAVE_OPTION_TABLE=1
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+option CONFIG_SMP=1
+option CONFIG_MAX_CPUS=4
+
+##
+## Build code to setup a generic IOAPIC
+##
+option CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+option MAINBOARD_PART_NUMBER="QUARTET"
+option MAINBOARD_VENDOR="AMD"
+
 ###
-### Build the objects we have code for in this directory.
+### LinuxBIOS layout values
 ###
-##object mainboard.o
-driver mainboard.o
-object static_devices.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
-#
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+option ROM_SIZE = 524288
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+option ROM_IMAGE_SIZE = 65536
+
+##
+## Use a small 8K stack
+##
+option STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+option HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+option USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+
+##
+## Compute the location and size of where this firmware image
+## (linuxBIOS plus bootloader) will live in the boot rom chip.
+##
+if USE_FALLBACK_IMAGE
+	option ROM_SECTION_SIZE   = FALLBACK_SIZE
+	option ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+else
+	option ROM_SECTION_SIZE   = ( ROM_SIZE - FALLBACK_SIZE )
+	option ROM_SECTION_OFFSET = 0
+end
+
+##
+## Compute the start location and size size of
+## The linuxBIOS bootloader.
+##
+option PAYLOAD_SIZE            = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+option CONFIG_ROM_STREAM     = 1
+
+##
+## Compute where this copy of linuxBIOS will start in the boot rom
+##
+option _ROMBASE      = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up linuxBIOS,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+option XIP_ROM_SIZE=65536
+option XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+##
+## Set all of the defaults for an x86 architecture
+##
+
 arch i386 end
 #cpu k8 end
-#
-###
-### Build our 16 bit and 32 bit linuxBIOS entry code
-###
+
+##
+## Build the objects we have code for in this directory.
+##
+
+#object mainboard.o
+driver mainboard.o
+#object static_devices.o
+if HAVE_MP_TABLE object mptable.o end
+if HAVE_PIRQ_TABLE object irq_tables.o end
+object reset.o
+
+##
+## Romcc output
+##
+makerule ./failover.E
+	depends "$(MAINBOARD)/failover.c" 
+	action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E"
+end
+
+makerule ./failover.inc
+	depends "./failover.E ./romcc"
+	action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"
+end
+
+makerule ./auto.E 
+	depends	"$(MAINBOARD)/auto.c" 
+	action	"$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+end
+makerule ./auto.inc 
+	depends "./auto.E ./romcc"
+	action	"./romcc -mcpu=k8  -O ./auto.E > auto.inc"
+end
+
+##
+## Build our 16 bit and 32 bit linuxBIOS entry code
+##
 mainboardinit cpu/i386/entry16.inc
 mainboardinit cpu/i386/entry32.inc
 ldscript /cpu/i386/entry16.lds
 ldscript /cpu/i386/entry32.lds
-#
-###
-### Build our reset vector (This is where linuxBIOS is entered)
-###
+
+##
+## Build our reset vector (This is where linuxBIOS is entered)
+##
 if USE_FALLBACK_IMAGE 
 	mainboardinit cpu/i386/reset16.inc 
 	ldscript /cpu/i386/reset16.lds 
@@ -38,81 +182,130 @@ else
 	mainboardinit cpu/i386/reset32.inc 
 	ldscript /cpu/i386/reset32.lds 
 end
-#
-#### Should this be in the northbridge code?
+
+### Should this be in the northbridge code?
 mainboardinit arch/i386/lib/cpu_reset.inc
-###
-### Setup the serial port
-###
-#mainboardinit superiowinbond/w83627hf/setup_serial.inc
-mainboardinit pc80/serial.inc
-mainboardinit arch/i386/lib/console.inc
-#
-###
-### Include an id string (For safe flashing)
-###
+
+##
+## Include an id string (For safe flashing)
+##
 mainboardinit arch/i386/lib/id.inc
 ldscript /arch/i386/lib/id.lds
-#
-####
-#### This is the early phase of linuxBIOS startup 
-#### Things are delicate and we test to see if we should
-#### failover to another image.
-####
-#option MAX_REBOOT_CNT=2
-if USE_FALLBACK_IMAGE
-  ldscript /arch/i386/lib/failover.lds 
-end
-#
-###
-### Setup our mtrrs
-###
-mainboardinit cpu/k8/earlymtrr.inc
-#
-#
-####
-#### O.k. We aren't just an intermediary anymore!
-####
-#
-###
-### When debugging disable the watchdog timer
-###
-##option MAXIMUM_CONSOLE_LOGLEVEL=7
-#default MAXIMUM_CONSOLE_LOGLEVEL=7
-#
-if USE_FALLBACK_IMAGE mainboardinit arch/i386/lib/noop_failover.inc  end
-#
-###
-### Romcc output
-###
-#makerule ./failover.E dep "$(MAINBOARD)/failover.c" act "$(CPP) -I$(TOP)/src $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failever.E"
-#makerule ./failover.inc dep "./romcc ./failover.E" act "./romcc -O ./failover.E > failover.inc"
-#mainboardinit .failover.inc
-makerule ./auto.E 
-	depends	"$(MAINBOARD)/auto.c" 
-	action	"$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
-end
-makerule ./auto.inc 
-	depends "./romcc ./auto.E" 
-	action	"./romcc -O ./auto.E > auto.inc"
-end
-mainboardinit ./auto.inc
-#
-###
-### Include the secondary Configuration files 
-###
-northbridge amd/amdk8
-end
-southbridge amd/amd8111
-end
-#mainboardinit archi386/smp/secondary.inc
-superio NSC/pc87360
-	register ".com1={1}, .com2={0}, .floppy=1, .lpt=1, .keyboard=1"
-end
-dir /pc80
-##dir /src/superio/winbond/w83627hf
-cpu p5 end
-cpu p6 end
-cpu k7 end
-cpu k8 end
+
+##
+## Setup our mtrrs
+##
+mainboardinit cpu/k8/earlymtrr.inc
+
+###
+### This is the early phase of linuxBIOS startup 
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if USE_FALLBACK_IMAGE
+	ldscript /arch/i386/lib/failover.lds 
+	mainboardinit ./failover.inc
+end
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+mainboardinit cpu/k8/enable_mmx_sse.inc
+mainboardinit ./auto.inc
+mainboardinit cpu/k8/disable_mmx_sse.inc
+
+##
+## Include the secondary Configuration files 
+##
+dir /pc80
+config chip.h
+
+northbridge amd/amdk8 "mc0"
+	pci 0:18.0
+	pci 0:18.0
+	pci 0:18.0
+	pci 0:18.1
+	pci 0:18.2
+	pci 0:18.3
+	southbridge amd/amd8131 "amd8131"
+		pci 0:0.0
+		pci 0:0.1
+		pci 0:1.0
+		pci 0:1.1
+	end
+	southbridge amd/amd8111 "amd8111"
+		pci 0:0.0
+		pci 0:1.0
+		pci 0:1.1
+		pci 0:1.2
+		pci 0:1.3
+		pci 0:1.5
+		pci 0:1.6
+		superio NSC/pc87360
+			pnp 1:2e.0
+			pnp 1:2e.1
+			pnp 1:2e.2
+			pnp 1:2e.3
+			pnp 1:2e.4
+			pnp 1:2e.5
+			pnp 1:2e.6
+			pnp 1:2e.7
+			pnp 1:2e.8
+			pnp 1:2e.9
+			pnp 1:2e.a
+			register "com1" = "{1, 0, 0x3f8, 4}"
+			register "lpt" = "{1}"
+		end
+	end
+end
+
+northbridge amd/amdk8 "mc1"
+	pci 0:19.0
+	pci 0:19.0
+	pci 0:19.0
+	pci 0:19.1
+	pci 0:19.2
+	pci 0:19.3
+end
+
+northbridge amd/amdk8 "mc2"
+	pci 0:1a.0
+	pci 0:1a.0
+	pci 0:1a.0
+	pci 0:1a.1
+	pci 0:1a.2
+	pci 0:1a.3
+end
+
+northbridge amd/amdk8 "mc3"
+	pci 0:1b.0
+	pci 0:1b.0
+	pci 0:1b.0
+	pci 0:1b.1
+	pci 0:1b.2
+	pci 0:1b.3
+end
+
+cpu k8 "cpu0"
+	register "up" = "{ .chip = &amd8131, .ht_width=16, .ht_speed=600 }"
+end
+
+cpu k8 "cpu1" 
+end
+
+cpu k8 "cpu2" 
+end
+
+cpu k8 "cpu3" 
+end
+
+##
+## Include the old serial code for those few places that still need it.
+##
+mainboardinit pc80/serial.inc
+mainboardinit arch/i386/lib/console.inc
 
diff --git a/src/mainboard/amd/quartet/auto.c b/src/mainboard/amd/quartet/auto.c
index 3166f7ad3c..5632dfcfd3 100644
--- a/src/mainboard/amd/quartet/auto.c
+++ b/src/mainboard/amd/quartet/auto.c
@@ -25,6 +25,8 @@ static void memreset_setup(void)
 	outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 28);
 	/* Ensure the BIOS has control of the memory lines */
 	outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 29);
+	outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 30);
+	outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 31);
 }
 
 static void memreset(int controllers, const struct mem_controller *ctrl)
@@ -211,7 +213,7 @@ static void main(void)
 	enable_lapic();
 	init_timer();
 	if (!boot_cpu()) {
-		notify_bsp_ap_is_stopped();
+//		notify_bsp_ap_is_stopped();
 		stop_this_cpu();
 	}
 	pc87360_enable_serial();
diff --git a/src/mainboard/amd/quartet/chip.h b/src/mainboard/amd/quartet/chip.h
new file mode 100644
index 0000000000..191eb65e5c
--- /dev/null
+++ b/src/mainboard/amd/quartet/chip.h
@@ -0,0 +1,5 @@
+struct chip_control mainboard_amd_quartet_control;
+
+struct mainboard_amd_quartet_config {
+	int nothing;
+};
diff --git a/src/mainboard/amd/quartet/irq_tables.c b/src/mainboard/amd/quartet/irq_tables.c
index 286905c26f..5e4437ca11 100644
--- a/src/mainboard/amd/quartet/irq_tables.c
+++ b/src/mainboard/amd/quartet/irq_tables.c
@@ -7,25 +7,37 @@
 
 #include <arch/pirq_routing.h>
 
+
 const struct irq_routing_table intel_irq_routing_table = {
 	PIRQ_SIGNATURE, /* u32 signature */
 	PIRQ_VERSION,   /* u16 version   */
-	32+16*7,        /* there can be total 7 devices on the bus */
-	0,              /* Where the interrupt router lies (bus) */
-	(5<<3)|3,       /* Where the interrupt router lies (dev) */
-	0xc20,          /* IRQs devoted exclusively to PCI usage */
+	32+16*18,        /* there can be total 18 devices on the bus */
+	0,           /* Where the interrupt router lies (bus) */
+	0x23,           /* Where the interrupt router lies (dev) */
+	0,         /* IRQs devoted exclusively to PCI usage */
 	0x1022,         /* Vendor */
 	0x746b,         /* Device */
-	0,              /* Crap (miniport) */
+	0,         /* Crap (miniport) */
 	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
-	0xdf,           /*  u8 checksum , mod 256 checksum must give zero */
-	{  /* bus, devfn,     {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu  */
-	    {0x02, (5<<3)|0, {{0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x01, 0xdeb8}}, 0x02, 0x00},
-	    {0x02, (6<<3)|0, {{0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x01, 0xdeb8}, {0x02, 0xdeb8}}, 0x03, 0x00},
-	    {0x02, (7<<3)|0, {{0x04, 0xdeb8}, {0x01, 0xdeb8}, {0x02, 0xdeb8}, {0x03, 0xdeb8}}, 0x04, 0x00},
-	    {0x02, (1<<3)|1, {{0x01, 0xdeb8}, {0x01, 0xdeb8}, {0x01, 0xdeb8}, {0x01, 0xdeb8}}, 0x00, 0x00},
-	    {0x00, (5<<3)|1, {{0x01, 0xdeb8}, {0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x04, 0xdeb8}}, 0x00, 0x00},
-	    {0x00, (2<<3)|0, {{0x01, 0xdeb8}, {0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x04, 0xdeb8}}, 0x00, 0x00},
-	    {0xff, 0xff,     {{0xff, 0xffff}, {0xff, 0xffff}, {0xff, 0xffff}, {0xff, 0xffff}}, 0xff, 0xff},
+	0x35,         /*  u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+	{
+		{0,0xc0, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0,0x50, {{0x1, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x2,0x8, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x3, 0},
+		{0x2,0x10, {{0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}}, 0x4, 0},
+		{0x1,0x18, {{0x4, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0x0, 0},
+		{0x1,0x20, {{0x4, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0x0, 0},
+		{0x2,0x28, {{0x2, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0xa, 0},
+		{0,0x58, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x3,0x8, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x1, 0},
+		{0x3,0x10, {{0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}}, 0x2, 0},
+		{0x3,0x18, {{0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}}, 0x9, 0},
+		{0,0x30, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x1,0, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0x4, 0xdef8}}, 0, 0},
+		{0x1,0x28, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x5, 0},
+		{0x1,0x20, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x6, 0},
+		{0x1,0x30, {{0x3, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0xb, 0},
+		{0,0x38, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0,0xc8, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
 	}
 };
diff --git a/src/mainboard/amd/quartet/mainboard.c b/src/mainboard/amd/quartet/mainboard.c
index 0622150d64..6c4d435ee1 100644
--- a/src/mainboard/amd/quartet/mainboard.c
+++ b/src/mainboard/amd/quartet/mainboard.c
@@ -1,11 +1,42 @@
+
 #include <console/console.h>
 #include <device/device.h>
 #include <device/pci.h>
 #include <device/pci_ids.h>
 #include <device/pci_ops.h>
 
+#include <arch/io.h>
+#include <device/chip.h>
+#include "../../../northbridge/amd/amdk8/northbridge.h"
+#include "chip.h"
+
 
 unsigned long initial_apicid[CONFIG_MAX_CPUS] =
 {
-	0, 1, 2, 3
+	0, 1, 2, 3,
 };
+
+static struct device_operations mainboard_operations = {
+	.read_resources   = root_dev_read_resources,
+	.set_resources    = root_dev_set_resources,
+	.enable_resources = enable_childrens_resources,
+	.init             = 0,
+	.scan_bus         = amdk8_scan_root_bus,
+	.enable           = 0,
+};
+
+static void enumerate(struct chip *chip)
+{
+	struct chip *child;
+	dev_root.ops = &mainboard_operations;
+	chip->dev = &dev_root;
+	chip->bus = 0;
+	for(child = chip->children; child; child = child->next) {
+		child->bus = &dev_root.link[0];
+	}
+}
+struct chip_control mainboard_amd_quartet_control = {
+	.enumerate = enumerate, 
+	.name      = "AMD Quartet mainboard ",
+};
+
diff --git a/src/mainboard/amd/quartet/mptable.c b/src/mainboard/amd/quartet/mptable.c
index 847416eec5..94ac735744 100644
--- a/src/mainboard/amd/quartet/mptable.c
+++ b/src/mainboard/amd/quartet/mptable.c
@@ -7,8 +7,8 @@
 void *smp_write_config_table(void *v, unsigned long * processor_map)
 {
 	static const char sig[4] = "PCMP";
-	static const char oem[8] = "AMD     ";
-	static const char productid[12] = "QUARTET     ";
+	static const char oem[8] = "LNXI    ";
+	static const char productid[12] = "HDAMA       ";
 	struct mp_config_table *mc;
 	unsigned char bus_num;
 	unsigned char bus_isa;
@@ -36,40 +36,40 @@ void *smp_write_config_table(void *v, unsigned long * processor_map)
 	smp_write_processors(mc, processor_map);
 
 	{
-		struct pci_dev *dev;
-		uint32_t base;
+		device_t dev;
+
 		/* 8111 */
-		dev = dev_find_slot(0, PCI_DEVFN(0x03,0));
+		dev = dev_find_slot(1, PCI_DEVFN(0x03,0));
 		if (dev) {
 			bus_8111_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
 			bus_isa	   = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
 			bus_isa++;
 		}
 		else {
-			printk_debug("ERROR - could not find PCI 0:03.0, using defaults\n");
+			printk_debug("ERROR - could not find PCI 1:03.0, using defaults\n");
 
 			bus_8111_1 = 3;
 			bus_isa = 4;
 		}
 		/* 8131-1 */
-		dev = dev_find_slot(0, PCI_DEVFN(0x01,0));
+		dev = dev_find_slot(1, PCI_DEVFN(0x01,0));
 		if (dev) {
 			bus_8131_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
 
 		}
 		else {
-			printk_debug("ERROR - could not find PCI 0:01.0, using defaults\n");
+			printk_debug("ERROR - could not find PCI 1:01.0, using defaults\n");
 
 			bus_8131_1 = 1;
 		}
 		/* 8131-2 */
-		dev = dev_find_slot(0, PCI_DEVFN(0x02,0));
+		dev = dev_find_slot(1, PCI_DEVFN(0x02,0));
 		if (dev) {
 			bus_8131_2 = pci_read_config8(dev, PCI_SECONDARY_BUS);
 
 		}
 		else {
-			printk_debug("ERROR - could not find PCI 0:02.0, using defaults\n");
+			printk_debug("ERROR - could not find PCI 1:02.0, using defaults\n");
 
 			bus_8131_2 = 2;
 		}
@@ -85,17 +85,17 @@ void *smp_write_config_table(void *v, unsigned long * processor_map)
 
 	smp_write_ioapic(mc, 2, 0x11, 0xfec00000);
 	{
-		struct pci_dev *dev;
+		device_t dev;
 		uint32_t base;
 		/* 8131 apic 3 */
-		dev = dev_find_slot(0, PCI_DEVFN(0x01,1));
+		dev = dev_find_slot(1, PCI_DEVFN(0x01,1));
 		if (dev) {
 			base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
 			base &= PCI_BASE_ADDRESS_MEM_MASK;
 			smp_write_ioapic(mc, 0x03, 0x11, base);
 		}
 		/* 8131 apic 4 */
-		dev = dev_find_slot(0, PCI_DEVFN(0x02,1));
+		dev = dev_find_slot(1, PCI_DEVFN(0x02,1));
 		if (dev) {
 			base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
 			base &= PCI_BASE_ADDRESS_MEM_MASK;
@@ -150,43 +150,43 @@ void *smp_write_config_table(void *v, unsigned long * processor_map)
 
 	/* PCI Slot 1 */
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_2, (1<<2)|0, 0x04, 0x1);
+		bus_8131_2, (1<<2)|0, 0x02, 0x11);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_2, (1<<2)|1, 0x04, 0x2);
+		bus_8131_2, (1<<2)|1, 0x02, 0x12);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_2, (1<<2)|2, 0x04, 0x3);
+		bus_8131_2, (1<<2)|2, 0x02, 0x13);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_2, (1<<2)|3, 0x04, 0x0);
+		bus_8131_2, (1<<2)|3, 0x02, 0x10);
 
 	/* PCI Slot 2 */
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_2, (2<<2)|0, 0x04, 0x2);
+		bus_8131_2, (2<<2)|0, 0x02, 0x12);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_2, (2<<2)|1, 0x04, 0x3);
+		bus_8131_2, (2<<2)|1, 0x02, 0x13);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_2, (2<<2)|2, 0x04, 0x0);
+		bus_8131_2, (2<<2)|2, 0x02, 0x10);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_2, (2<<2)|3, 0x04, 0x1);
+		bus_8131_2, (2<<2)|3, 0x02, 0x11);
 
 	/* PCI Slot 3 */
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_1, (1<<2)|0, 0x03, 0x1);
+		bus_8131_1, (1<<2)|0, 0x02, 0x11);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_1, (1<<2)|1, 0x03, 0x2);
+		bus_8131_1, (1<<2)|1, 0x02, 0x12);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_1, (1<<2)|2, 0x03, 0x3);
+		bus_8131_1, (1<<2)|2, 0x02, 0x13);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_1, (1<<2)|3, 0x03, 0x0);
+		bus_8131_1, (1<<2)|3, 0x02, 0x10);
 
 	/* PCI Slot 4 */
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_1, (2<<2)|0, 0x03, 0x2);
+		bus_8131_1, (2<<2)|0, 0x02, 0x12);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_1, (2<<2)|1, 0x03, 0x3);
+		bus_8131_1, (2<<2)|1, 0x02, 0x13);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_1, (2<<2)|2, 0x03, 0x0);
+		bus_8131_1, (2<<2)|2, 0x02, 0x10);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT,
-		bus_8131_1, (2<<2)|3, 0x03, 0x1);
+		bus_8131_1, (2<<2)|3, 0x02, 0x11);
 
 	/* PCI Slot 5 */
 #warning "FIXME get the irqs right, it's just hacked to work for now"
diff --git a/src/mainboard/amd/quartet/resourcemap.c b/src/mainboard/amd/quartet/resourcemap.c
index bf1e388238..f34e6f5327 100644
--- a/src/mainboard/amd/quartet/resourcemap.c
+++ b/src/mainboard/amd/quartet/resourcemap.c
@@ -34,10 +34,10 @@ static void setup_quartet_resource_map(void)
 	 *         This field defines the upper address bits of a 40 bit  address
 	 *         that define the end of the DRAM region.
 	 */
-	PCI_ADDR(0, 0x18, 1, 0x44), 0x0000f8f8, 0x00f00000,
-	PCI_ADDR(0, 0x18, 1, 0x4C), 0x0000f8f8, 0x01f00001,
-	PCI_ADDR(0, 0x18, 1, 0x54), 0x0000f8f8, 0x02f00002,
-	PCI_ADDR(0, 0x18, 1, 0x5C), 0x0000f8f8, 0x03f00003,
+	PCI_ADDR(0, 0x18, 1, 0x44), 0x0000f8f8, 0x000f0000,
+	PCI_ADDR(0, 0x18, 1, 0x4C), 0x0000f8f8, 0x001f0001,
+	PCI_ADDR(0, 0x18, 1, 0x54), 0x0000f8f8, 0x002f0002,
+	PCI_ADDR(0, 0x18, 1, 0x5C), 0x0000f8f8, 0x003f0003,
 	PCI_ADDR(0, 0x18, 1, 0x64), 0x0000f8f8, 0x00000004,
 	PCI_ADDR(0, 0x18, 1, 0x6C), 0x0000f8f8, 0x00000005,
 	PCI_ADDR(0, 0x18, 1, 0x74), 0x0000f8f8, 0x00000006,
@@ -256,7 +256,7 @@ static void setup_quartet_resource_map(void)
 	PCI_ADDR(0, 0x18, 1, 0xE0), 0x0000FC88, 0x07000203,
 	PCI_ADDR(0, 0x18, 1, 0xE4), 0x0000FC88, 0xff080113,
 	PCI_ADDR(0, 0x18, 1, 0xE8), 0x0000FC88, 0xffff0040,
-	PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0xffff0330,
+	PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0xffff0270,
 	};
 	int max;
 	max = sizeof(register_values)/sizeof(register_values[0]);