mb/google/brya/variants/redrix: Init devicetree for redrix
Init basic override devicetree based on schematics BUG=b:192052098 TEST=FW_NAME=redrix emerge-brya coreboot chromeos-bootimage Change-Id: I9fb752fe8280893b84c172d8a519578fa4220184 Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/56656 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This commit is contained in:
Wisley Chen
Tim Wawrzynczak
parent
37d14cfd30
commit
5d74ccf1c3
|
|
@ -20,6 +20,8 @@ config BOARD_GOOGLE_GIMBLE
|
|||
config BOARD_GOOGLE_REDRIX
|
||||
bool "-> Redrix"
|
||||
select BOARD_GOOGLE_BASEBOARD_BRYA
|
||||
select CHROMEOS_DSM_CALIB if CHROMEOS
|
||||
select DRIVERS_I2C_MAX98390
|
||||
|
||||
config BOARD_GOOGLE_KANO
|
||||
bool "-> Kano"
|
||||
|
|
|
|||
|
|
@ -2,3 +2,5 @@
|
|||
bootblock-y += gpio.c
|
||||
|
||||
ramstage-y += gpio.c
|
||||
|
||||
ramstage-$(CONFIG_FW_CONFIG) += fw_config.c
|
||||
|
|
|
|||
|
|
@ -0,0 +1,56 @@
|
|||
/* SPDX-License-Identifier: GPL-2.0-only */
|
||||
|
||||
#include <bootstate.h>
|
||||
#include <console/console.h>
|
||||
#include <fw_config.h>
|
||||
#include <gpio.h>
|
||||
|
||||
static const struct pad_config dmic_enable_pads[] = {
|
||||
PAD_CFG_NF(GPP_R4, NONE, DEEP, NF3), /* DMIC_CLK0_R */
|
||||
PAD_CFG_NF(GPP_R5, NONE, DEEP, NF3), /* DMIC_DATA0_R */
|
||||
|
||||
};
|
||||
|
||||
static const struct pad_config dmic_disable_pads[] = {
|
||||
PAD_NC(GPP_R4, NONE),
|
||||
PAD_NC(GPP_R5, NONE),
|
||||
};
|
||||
|
||||
static const struct pad_config i2s_enable_pads[] = {
|
||||
PAD_CFG_NF(GPP_R0, NONE, DEEP, NF2), /* I2S_HP_SCLK_R */
|
||||
PAD_CFG_NF(GPP_R1, NONE, DEEP, NF2), /* I2S_HP_SFRM_R */
|
||||
PAD_CFG_NF(GPP_R2, DN_20K, DEEP, NF2), /* I2S_PCH_TX_HP_RX_STRAP */
|
||||
PAD_CFG_NF(GPP_R3, NONE, DEEP, NF2), /* I2S_PCH_RX_HP_TX */
|
||||
PAD_CFG_NF(GPP_S0, NONE, DEEP, NF4), /* I2S_SPKR_SCLK_R */
|
||||
PAD_CFG_NF(GPP_S1, NONE, DEEP, NF4), /* I2S_SPKR_SFRM_R */
|
||||
PAD_CFG_NF(GPP_S2, NONE, DEEP, NF4), /* I2S_PCH_TX_SPKR_RX_R */
|
||||
PAD_CFG_NF(GPP_S3, NONE, DEEP, NF4), /* I2S_PCH_RX_SPKR_TX */
|
||||
};
|
||||
|
||||
static const struct pad_config i2s_disable_pads[] = {
|
||||
PAD_NC(GPP_R0, NONE),
|
||||
PAD_NC(GPP_R1, NONE),
|
||||
PAD_NC(GPP_R2, NONE),
|
||||
PAD_NC(GPP_R3, NONE),
|
||||
PAD_NC(GPP_S0, NONE),
|
||||
PAD_NC(GPP_S1, NONE),
|
||||
PAD_NC(GPP_S2, NONE),
|
||||
PAD_NC(GPP_S3, NONE),
|
||||
};
|
||||
|
||||
static void fw_config_handle(void *unused)
|
||||
{
|
||||
if (!fw_config_is_provisioned() || fw_config_probe(FW_CONFIG(AUDIO, AUDIO_UNKNOWN))) {
|
||||
printk(BIOS_INFO, "Disable audio related GPIO pins.\n");
|
||||
gpio_configure_pads(i2s_disable_pads, ARRAY_SIZE(i2s_disable_pads));
|
||||
gpio_configure_pads(dmic_disable_pads, ARRAY_SIZE(dmic_disable_pads));
|
||||
return;
|
||||
}
|
||||
|
||||
if (fw_config_probe(FW_CONFIG(AUDIO, MAX98390_ALC5682I_I2S))) {
|
||||
printk(BIOS_INFO, "Configure audio over I2S with MAX98390 ALC5682I.\n");
|
||||
gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads));
|
||||
gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads));
|
||||
}
|
||||
}
|
||||
BOOT_STATE_INIT_ENTRY(BS_DEV_ENABLE, BS_ON_ENTRY, fw_config_handle, NULL);
|
||||
|
|
@ -1,6 +1,339 @@
|
|||
chip soc/intel/alderlake
|
||||
|
||||
device domain 0 on
|
||||
fw_config
|
||||
field DB_SD 0 1
|
||||
option SD_ABSENT 0
|
||||
option SD_GL9755S 1
|
||||
end
|
||||
field KB_BL 2 2
|
||||
option KB_BL_ABSENT 0
|
||||
option KB_BL_PRESENT 1
|
||||
end
|
||||
field AUDIO 3 5
|
||||
option AUDIO_UNKNOWN 0
|
||||
option MAX98390_ALC5682I_I2S 1
|
||||
end
|
||||
field DB_LTE 6 7
|
||||
option LTE_ABSENT 0
|
||||
option LTE_USB 1
|
||||
option LTE_PCIE 2
|
||||
end
|
||||
end
|
||||
chip soc/intel/alderlake
|
||||
# Intel Common SoC Config
|
||||
#+-------------------+---------------------------+
|
||||
#| Field | Value |
|
||||
#+-------------------+---------------------------+
|
||||
#| chipset_lockdown | CHIPSET_LOCKDOWN_COREBOOT |
|
||||
#| GSPI1 | Fingerprint MCU |
|
||||
#| I2C0 | Audio |
|
||||
#| I2C1 | Touchscreen |
|
||||
#| I2C2 | |
|
||||
#| I2C3 | cr50 TPM. Early init is |
|
||||
#| | required to set up a BAR |
|
||||
#| | for TPM communication |
|
||||
#| I2C5 | Trackpad |
|
||||
#+-------------------+---------------------------+
|
||||
register "common_soc_config" = "{
|
||||
.chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT,
|
||||
.i2c[0] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
},
|
||||
.i2c[1] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
},
|
||||
.i2c[2] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
},
|
||||
.i2c[3] = {
|
||||
.early_init = 1,
|
||||
.speed = I2C_SPEED_FAST,
|
||||
},
|
||||
.i2c[5] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
},
|
||||
}"
|
||||
device domain 0 on
|
||||
device ref dtt on
|
||||
chip drivers/intel/dptf
|
||||
## sensor information
|
||||
register "options.tsr[0].desc" = ""DRAM""
|
||||
register "options.tsr[1].desc" = ""Charger""
|
||||
# TODO: below values are initial reference values only
|
||||
## Active Policy
|
||||
register "policies.active" = "{
|
||||
[0] = {
|
||||
.target = DPTF_CPU,
|
||||
.thresholds = {
|
||||
TEMP_PCT(85, 90),
|
||||
TEMP_PCT(80, 80),
|
||||
TEMP_PCT(75, 70),
|
||||
}
|
||||
}
|
||||
}"
|
||||
## Passive Policy
|
||||
register "policies.passive" = "{
|
||||
[0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
|
||||
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
|
||||
[2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
|
||||
}"
|
||||
## Critical Policy
|
||||
register "policies.critical" = "{
|
||||
[0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
|
||||
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
|
||||
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
|
||||
}"
|
||||
register "controls.power_limits" = "{
|
||||
.pl1 = {
|
||||
.min_power = 3000,
|
||||
.max_power = 15000,
|
||||
.time_window_min = 28 * MSECS_PER_SEC,
|
||||
.time_window_max = 32 * MSECS_PER_SEC,
|
||||
.granularity = 200,
|
||||
},
|
||||
.pl2 = {
|
||||
.min_power = 55000,
|
||||
.max_power = 55000,
|
||||
.time_window_min = 28 * MSECS_PER_SEC,
|
||||
.time_window_max = 32 * MSECS_PER_SEC,
|
||||
.granularity = 1000,
|
||||
}
|
||||
}"
|
||||
## Charger Performance Control (Control, mA)
|
||||
register "controls.charger_perf" = "{
|
||||
[0] = { 255, 1700 },
|
||||
[1] = { 24, 1500 },
|
||||
[2] = { 16, 1000 },
|
||||
[3] = { 8, 500 }
|
||||
}"
|
||||
## Fan Performance Control (Percent, Speed, Noise, Power)
|
||||
register "controls.fan_perf" = "{
|
||||
[0] = { 90, 6700, 220, 2200, },
|
||||
[1] = { 80, 5800, 180, 1800, },
|
||||
[2] = { 70, 5000, 145, 1450, },
|
||||
[3] = { 60, 4900, 115, 1150, },
|
||||
[4] = { 50, 3838, 90, 900, },
|
||||
[5] = { 40, 2904, 55, 550, },
|
||||
[6] = { 30, 2337, 30, 300, },
|
||||
[7] = { 20, 1608, 15, 150, },
|
||||
[8] = { 10, 800, 10, 100, },
|
||||
[9] = { 0, 0, 0, 50, }
|
||||
}"
|
||||
## Fan options
|
||||
register "options.fan.fine_grained_control" = "1"
|
||||
register "options.fan.step_size" = "2"
|
||||
device generic 0 on end
|
||||
end
|
||||
end
|
||||
device ref cnvi_wifi on
|
||||
chip drivers/wifi/generic
|
||||
register "wake" = "GPE0_PME_B0"
|
||||
device generic 0 on end
|
||||
end
|
||||
end
|
||||
device ref tcss_dma0 on
|
||||
chip drivers/intel/usb4/retimer
|
||||
register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
|
||||
use tcss_usb3_port1 as dfp[0].typec_port
|
||||
device generic 0 on end
|
||||
end
|
||||
end
|
||||
device ref tcss_dma1 on
|
||||
chip drivers/intel/usb4/retimer
|
||||
register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
|
||||
use tcss_usb3_port3 as dfp[0].typec_port
|
||||
device generic 0 on end
|
||||
end
|
||||
end
|
||||
device ref pcie_rp8 on
|
||||
chip soc/intel/common/block/pcie/rtd3
|
||||
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
|
||||
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)"
|
||||
register "srcclk_pin" = "3"
|
||||
device generic 0 on end
|
||||
end
|
||||
end #PCIE8 SD card
|
||||
device ref i2c0 on
|
||||
chip drivers/i2c/generic
|
||||
register "hid" = ""10EC5682""
|
||||
register "name" = ""RT58""
|
||||
register "desc" = ""Headset Codec""
|
||||
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
|
||||
# Set the jd_src to RT5668_JD1 for jack detection
|
||||
register "property_count" = "1"
|
||||
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
|
||||
register "property_list[0].name" = ""realtek,jd-src""
|
||||
register "property_list[0].integer" = "1"
|
||||
device i2c 1a on
|
||||
end
|
||||
end
|
||||
end #I2C0
|
||||
device ref i2c1 on
|
||||
chip drivers/i2c/hid
|
||||
register "generic.hid" = ""ELAN2513""
|
||||
register "generic.desc" = ""ELAN Touchscreen""
|
||||
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
|
||||
register "generic.probed" = "1"
|
||||
register "generic.reset_gpio" =
|
||||
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
|
||||
register "generic.reset_delay_ms" = "300"
|
||||
register "generic.reset_off_delay_ms" = "1"
|
||||
register "generic.enable_gpio" =
|
||||
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
|
||||
register "generic.enable_delay_ms" = "6"
|
||||
register "generic.stop_gpio" =
|
||||
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
|
||||
register "generic.stop_off_delay_ms" = "1"
|
||||
register "generic.has_power_resource" = "1"
|
||||
register "hid_desc_reg_offset" = "0x01"
|
||||
device i2c 0x15 on end
|
||||
end
|
||||
end
|
||||
device ref i2c5 on
|
||||
chip drivers/i2c/generic
|
||||
register "hid" = ""ELAN0000""
|
||||
register "desc" = ""ELAN Touchpad""
|
||||
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
|
||||
register "wake" = "GPE0_DW2_14"
|
||||
register "probed" = "1"
|
||||
device i2c 15 on end
|
||||
end
|
||||
end
|
||||
device ref hda on
|
||||
chip drivers/i2c/max98390
|
||||
register "desc" = ""MAX98390 Speaker Amp 0""
|
||||
register "uid" = "0"
|
||||
register "name" = ""MXW0""
|
||||
register "r0_calib_key" = ""dsm_calib_r0_0""
|
||||
register "temperature_calib_key" = ""dsm_calib_temp_0""
|
||||
device i2c 0x70 on end
|
||||
end
|
||||
chip drivers/i2c/max98390
|
||||
register "desc" = ""MAX98390 Speaker Amp 1""
|
||||
register "uid" = "1"
|
||||
register "name" = ""MXW1""
|
||||
register "r0_calib_key" = ""dsm_calib_r0_1""
|
||||
register "temperature_calib_key" = ""dsm_calib_temp_1""
|
||||
device i2c 0x72 on end
|
||||
end
|
||||
chip drivers/i2c/max98390
|
||||
register "desc" = ""MAX98390 Speaker Amp 2""
|
||||
register "uid" = "2"
|
||||
register "name" = ""MXW2""
|
||||
register "r0_calib_key" = ""dsm_calib_r0_2""
|
||||
register "temperature_calib_key" = ""dsm_calib_temp_2""
|
||||
device i2c 0x74 on end
|
||||
end
|
||||
chip drivers/i2c/max98390
|
||||
register "desc" = ""MAX98390 Speaker Amp 3""
|
||||
register "uid" = "3"
|
||||
register "name" = ""MXW3""
|
||||
register "r0_calib_key" = ""dsm_calib_r0_3""
|
||||
register "temperature_calib_key" = ""dsm_calib_temp_3""
|
||||
device i2c 0x76 on end
|
||||
end
|
||||
end
|
||||
device ref gspi1 on
|
||||
chip drivers/spi/acpi
|
||||
register "name" = ""CRFP""
|
||||
register "hid" = "ACPI_DT_NAMESPACE_HID"
|
||||
register "uid" = "1"
|
||||
register "compat_string" = ""google,cros-ec-spi""
|
||||
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)"
|
||||
register "wake" = "GPE0_DW2_15"
|
||||
device spi 0 on end
|
||||
end # FPMCU
|
||||
end
|
||||
device ref pch_espi on
|
||||
chip ec/google/chromeec
|
||||
use conn0 as mux_conn[0]
|
||||
use conn1 as mux_conn[1]
|
||||
device pnp 0c09.0 on end
|
||||
end
|
||||
end
|
||||
device ref pmc hidden
|
||||
chip drivers/intel/pmc_mux
|
||||
device generic 0 on
|
||||
chip drivers/intel/pmc_mux/conn
|
||||
register "usb2_port_number" = "1"
|
||||
register "usb3_port_number" = "1"
|
||||
device generic 0 alias conn0 on end
|
||||
end
|
||||
chip drivers/intel/pmc_mux/conn
|
||||
register "usb2_port_number" = "3"
|
||||
register "usb3_port_number" = "3"
|
||||
device generic 1 alias conn1 on end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
device ref tcss_xhci on
|
||||
chip drivers/usb/acpi
|
||||
device ref tcss_root_hub on
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-C Port C0 (MLB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "group" = "ACPI_PLD_GROUP(1, 1)"
|
||||
device ref tcss_usb3_port1 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-C Port C2 (MLB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "group" = "ACPI_PLD_GROUP(3, 1)"
|
||||
device ref tcss_usb3_port3 on end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
device ref xhci on
|
||||
chip drivers/usb/acpi
|
||||
device ref xhci_root_hub on
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-C Port C0 (MLB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "group" = "ACPI_PLD_GROUP(1, 1)"
|
||||
device ref usb2_port1 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-C Port C2 (MLB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "group" = "ACPI_PLD_GROUP(3, 1)"
|
||||
device ref usb2_port3 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 WWAN""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
device ref usb2_port4 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Camera""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
device ref usb2_port6 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-A Port (MLB)""
|
||||
register "type" = "UPC_TYPE_A"
|
||||
register "group" = "ACPI_PLD_GROUP(4, 1)"
|
||||
device ref usb2_port9 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Bluetooth""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
register "reset_gpio" =
|
||||
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
|
||||
device ref usb2_port10 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-A Port (MLB)""
|
||||
register "type" = "UPC_TYPE_USB3_A"
|
||||
register "group" = "ACPI_PLD_GROUP(4, 1)"
|
||||
device ref usb3_port1 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 WWAN""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
device ref usb3_port4 on end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
|
||||
end
|
||||
|
|
|
|||
Loading…
Reference in New Issue