Documentation/acpi: Add new document on adding ACPI devices to devicetree
Change-Id: I9636e65f7d2499b06b1d71e5f8d09c528b850027 Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35080 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This commit is contained in:
parent
5cbaba48e6
commit
66e356c662
|
@ -0,0 +1,234 @@
|
|||
# Adding new devices to a device tree
|
||||
|
||||
## Introduction
|
||||
|
||||
ACPI exposes a platform-independent interface for operating systems to perform
|
||||
power management and other platform-level functions. Some operating systems
|
||||
also use ACPI to enumerate devices that are not immediately discoverable, such
|
||||
as those behind I2C or SPI busses (in contrast to PCI). This document discusses
|
||||
the way that coreboot uses the concept of a "device tree" to generate ACPI
|
||||
tables for usage by the operating system.
|
||||
|
||||
## Devicetree and overridetree (if applicable)
|
||||
|
||||
For mainboards that are organized around a "reference board" or "baseboard"
|
||||
model (see ``src/mainboard/google/octopus`` or ``hatch`` for examples), there is
|
||||
typically a devicetree.cb file that all boards share, and any differences for a
|
||||
specific board ("variant") are captured in the overridetree.cb file. Any
|
||||
settings changed in the overridetree take precedence over those in the main
|
||||
devicetree. Note, not all mainboards will have the devicetree/overridetree
|
||||
distinction, and may only have a devicetree.cb file. Or you can always just
|
||||
write the ASL (ACPI Source Language) code yourself.
|
||||
|
||||
## Device drivers
|
||||
|
||||
Let's take a look at an example entry from
|
||||
``src/mainboard/google/hatch/variant/hatch/overridetree.cb``:
|
||||
|
||||
```
|
||||
device pci 15.0 on
|
||||
chip drivers/i2c/generic
|
||||
register "hid" = ""ELAN0000""
|
||||
register "desc" = ""ELAN Touchpad""
|
||||
register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_A21_IRQ)"
|
||||
register "wake" = "GPE0_DW0_21"
|
||||
device i2c 15 on end
|
||||
end
|
||||
end # I2C #0
|
||||
```
|
||||
|
||||
When this entry is processed during ramstage, it will create a device in the
|
||||
ACPI SSDT table (all devices in devicetrees end up in the SSDT table). The ACPI
|
||||
generation routines in coreboot actually generate the raw bytecode that
|
||||
represents the device's structure, but looking at ASL code is easier to
|
||||
understand; see below for what the disassembled bytecode looks like:
|
||||
|
||||
```
|
||||
Scope (\_SB.PCI0.I2C0)
|
||||
{
|
||||
Device (D015)
|
||||
{
|
||||
Name (_HID, "ELAN0000") // _HID: Hardware ID
|
||||
Name (_UID, Zero) // _UID: Unique ID
|
||||
Name (_DDN, "ELAN Touchpad") // _DDN: DOS Device Name
|
||||
Method (_STA, 0, NotSerialized) // _STA: Status
|
||||
{
|
||||
Return (0x0F)
|
||||
}
|
||||
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
|
||||
{
|
||||
I2cSerialBusV2 (0x0015, ControllerInitiated, 400000,
|
||||
AddressingMode7Bit, "\\_SB.PCI0.I2C0",
|
||||
0x00, ResourceConsumer, , Exclusive, )
|
||||
Interrupt (ResourceConsumer, Edge, ActiveLow, ExclusiveAndWake, ,, )
|
||||
{
|
||||
0x0000002D,
|
||||
}
|
||||
})
|
||||
Name (_S0W, 0x04) // _S0W: S0 Device Wake State
|
||||
Name (_PRW, Package (0x02) // _PRW: Power Resources for Wake
|
||||
{
|
||||
0x15, // GPE #21
|
||||
0x03 // Sleep state S3
|
||||
})
|
||||
}
|
||||
}
|
||||
```
|
||||
|
||||
You can see it generates _HID, _UID, _DDN, _STA, _CRS, _S0W, and _PRW
|
||||
names/methods in the Device's scope.
|
||||
|
||||
## Utilizing a device driver
|
||||
|
||||
The device driver must be enabled for your build. There will be a CONFIG option
|
||||
in the Kconfig file in the directory that the driver is in (e.g.,
|
||||
``src/drivers/i2c/generic`` contains a Kconfig file; the option here is named
|
||||
CONFIG_DRIVERS_I2C_GENERIC). The config option will need to be added to your
|
||||
mainboard's Kconfig file (e.g., ``src/mainboard/google/hatch/Kconfig``) in order
|
||||
to be compiled into your build.
|
||||
|
||||
## Diving into the above example:
|
||||
|
||||
Let's take a look at how the devicetree language corresponds to the generated
|
||||
ASL.
|
||||
|
||||
First, note this:
|
||||
|
||||
```
|
||||
chip drivers/i2c/generic
|
||||
```
|
||||
|
||||
This means that the device driver we're using has a corresponding structure,
|
||||
located at ``src/drivers/i2c/generic/chip.h``, named **struct
|
||||
drivers_i2c_generic_config** and it contains many properties you can specify to
|
||||
be included in the ACPI table.
|
||||
|
||||
### hid
|
||||
|
||||
```
|
||||
register "hid" = ""ELAN0000""
|
||||
```
|
||||
|
||||
This corresponds to **const char *hid** in the struct. In the ACPI ASL, it
|
||||
translates to:
|
||||
|
||||
```
|
||||
Name (_HID, "ELAN0000") // _HID: Hardware ID
|
||||
```
|
||||
|
||||
under the device. **This property is used to match the device to its driver
|
||||
during enumeration in the OS.**
|
||||
|
||||
### desc
|
||||
|
||||
```
|
||||
register "desc" = ""ELAN Touchpad""
|
||||
```
|
||||
|
||||
corresponds to **const char *desc** and in ASL:
|
||||
|
||||
```
|
||||
Name (_DDN, "ELAN Touchpad") // _DDN: DOS Device Name
|
||||
```
|
||||
|
||||
### irq
|
||||
|
||||
It also adds the interrupt,
|
||||
|
||||
```
|
||||
Interrupt (ResourceConsumer, Edge, ActiveLow, ExclusiveAndWake, ,, )
|
||||
{
|
||||
0x0000002D,
|
||||
}
|
||||
```
|
||||
|
||||
which comes from:
|
||||
|
||||
```
|
||||
register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_A21_IRQ)"
|
||||
```
|
||||
|
||||
The GPIO pin IRQ settings control the "Edge", "ActiveLow", and
|
||||
"ExclusiveAndWake" settings seen above (edge means it is an edge-triggered
|
||||
interrupt as opposed to level-triggered; active low means the interrupt is
|
||||
triggered on a falling edge).
|
||||
|
||||
Note that the ACPI_IRQ_WAKE_EDGE_LOW macro informs the platform that the GPIO
|
||||
will be routed through SCI (ACPI's System Control Interrupt) for use as a wake
|
||||
source. Also note that the IRQ names are SoC-specific, and you will need to
|
||||
find the names in your SoC's header file. The ACPI_* macros are defined in
|
||||
``src/arch/x86/include/arch/acpi_device.h``.
|
||||
|
||||
Using a GPIO as an IRQ requires that it is configured in coreboot correctly.
|
||||
This is often done in a mainboard-specific file named ``gpio.c``.
|
||||
|
||||
### wake
|
||||
|
||||
The last register is:
|
||||
|
||||
```
|
||||
register "wake" = "GPE0_DW0_21"
|
||||
```
|
||||
|
||||
which indicates that the method of waking the system using the touchpad will be
|
||||
through a GPE, #21 associated with DW0, which is set up in devicetree.cb from
|
||||
this example. The "21" indicates GPP_X21, where GPP_X is mapped onto DW0
|
||||
elsewhere in the devicetree.
|
||||
|
||||
The last bit of the definition of that device includes:
|
||||
|
||||
```
|
||||
device i2c 15 on end
|
||||
```
|
||||
|
||||
which means it's an I2C device, with 7-bit address 0x15, and the device is "on",
|
||||
meaning it will be exposed in the ACPI table. The PCI device that the
|
||||
controller is located in determines which I2C bus the device is expected to be
|
||||
found on. In this example, this is I2C bus 0. This also determines the ACPI
|
||||
"Scope" that the device names and methods will live under, in this case
|
||||
"\_SB.PCI0.I2C0".
|
||||
|
||||
## Other auto-generated names
|
||||
|
||||
(see [ACPI specification
|
||||
6.3](https://uefi.org/sites/default/files/resources/ACPI_6_3_final_Jan30.pdf)
|
||||
for more details on ACPI methods)
|
||||
|
||||
### _S0W (S0 Device Wake State)
|
||||
_S0W indicates the deepest S0 sleep state this device can wake itself from,
|
||||
which in this case is 4, representing _D3cold_.
|
||||
|
||||
### _PRW (Power Resources for Wake)
|
||||
_PRW indicates the power resources and events required for wake. There are no
|
||||
dependent power resources, but the GPE (GPE0_DW0_21) is mentioned here (0x15),
|
||||
as well as the deepest sleep state supporting waking the system (3), which is
|
||||
S3.
|
||||
|
||||
### _STA (Status)
|
||||
The _STA method is generated automatically, and its values, 0xF, indicates the
|
||||
following:
|
||||
|
||||
Bit [0] – Set if the device is present.
|
||||
Bit [1] – Set if the device is enabled and decoding its resources.
|
||||
Bit [2] – Set if the device should be shown in the UI.
|
||||
Bit [3] – Set if the device is functioning properly (cleared if device failed its diagnostics).
|
||||
|
||||
### _CRS (Current resource settings)
|
||||
The _CRS method is generated automatically, as the driver knows it is an I2C
|
||||
controller, and so specifies how to configure the controller for proper
|
||||
operation with the touchpad.
|
||||
|
||||
```
|
||||
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
|
||||
{
|
||||
I2cSerialBusV2 (0x0015, ControllerInitiated, 400000,
|
||||
AddressingMode7Bit, "\\_SB.PCI0.I2C0",
|
||||
0x00, ResourceConsumer, , Exclusive, )
|
||||
```
|
||||
|
||||
## Notes
|
||||
|
||||
- **All fields that are left unspecified in the devicetree are initialized to
|
||||
zero.**
|
||||
- **All devices in devicetrees end up in the SSDT table, and are generated in
|
||||
coreboot's ramstage**
|
|
@ -172,6 +172,7 @@ Contents:
|
|||
* [Intel IFD Binary Extraction](Binary_Extraction.md)
|
||||
* [Dealing with Untrusted Input in SMM](technotes/2017-02-dealing-with-untrusted-input-in-smm.md)
|
||||
* [GPIO toggling in ACPI AML](acpi/gpio.md)
|
||||
* [Adding devices to a device tree](acpi/devicetree.md)
|
||||
* [Native Graphics Initialization with libgfxinit](gfx/libgfxinit.md)
|
||||
* [Display panel-specific documentation](gfx/display-panel.md)
|
||||
* [Architecture-specific documentation](arch/index.md)
|
||||
|
|
Loading…
Reference in New Issue