diff --git a/Documentation/mainboard/hp/compaq_8300_usdt.md b/Documentation/mainboard/hp/compaq_8300_usdt.md new file mode 100644 index 0000000000..1d4a0c7e8b --- /dev/null +++ b/Documentation/mainboard/hp/compaq_8300_usdt.md @@ -0,0 +1,66 @@ +# HP Compaq 8300 Elite USDT + +This page describes how to run coreboot on the [Compaq 8300 Elite USDT] desktop +from [HP]. + +## Flashing coreboot + +```eval_rst ++---------------------+-------------+ +| Type | Value | ++=====================+=============+ +| Socketed flash | no | ++---------------------+-------------+ +| Model | W25Q128BVFG | ++---------------------+-------------+ +| Size | 16 MiB | ++---------------------+-------------+ +| In circuit flashing | yes | ++---------------------+-------------+ +| Package | SOIC-16 | ++---------------------+-------------+ +| Write protection | No | ++---------------------+-------------+ +| Dual BIOS feature | No | ++---------------------+-------------+ +``` + +### Internal programming + +TODO: investigate + +The board has two jumpers that might be relevant: FDO (Flash Descriptor Override) and BB (?). + +### External programming + +Remove the lid. The flash chip can be found on the edge opposite to the CPU. +There is a spot for a "ROM RCVRY" header next to the flash chip but it is +unpopulated. If you don't feel like using a clip, you can easily solder +a standard pin header there yourself and use it for programming. + +Programming powers some parts of the board. Programming when +Wake on LAN is active works great. + +## Technology + +```eval_rst ++------------------+--------------------------------------------------+ +| Northbridge | :doc:`../../northbridge/intel/sandybridge/index` | ++------------------+--------------------------------------------------+ +| Southbridge | bd82x6x | ++------------------+--------------------------------------------------+ +| CPU | model_206ax | ++------------------+--------------------------------------------------+ +| SuperIO | NPCD379HAKFX | ++------------------+--------------------------------------------------+ +| Coprocessor | Intel ME | ++------------------+--------------------------------------------------+ +``` + +### SuperIO + +This board has a Nuvoton NPCD379 SuperIO chip. Fan speed and PS/2 keyboard work +fine using coreboot's existing code for :doc:`../../superio/nuvoton/npcd378`. + +[Compaq 8300 USDT]: https://support.hp.com/gb-en/product/hp-compaq-elite-8300-ultra-slim-pc/5232866 +[HP]: https://www.hp.com/ diff --git a/Documentation/mainboard/hp/compaq_8300_usdt_rom_header.jpg b/Documentation/mainboard/hp/compaq_8300_usdt_rom_header.jpg new file mode 100644 index 0000000000..967f91ca30 Binary files /dev/null and b/Documentation/mainboard/hp/compaq_8300_usdt_rom_header.jpg differ diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/Kconfig b/src/mainboard/hp/compaq_elite_8300_usdt/Kconfig new file mode 100644 index 0000000000..911bed01d2 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/Kconfig @@ -0,0 +1,38 @@ +if BOARD_HP_COMPAQ_ELITE_8300_USDT + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select BOARD_ROMSIZE_KB_16384 + select HAVE_ACPI_RESUME + select HAVE_ACPI_TABLES + select HAVE_CMOS_DEFAULT + select HAVE_OPTION_TABLE + select INTEL_INT15 + select MAINBOARD_HAS_TPM1 + select MAINBOARD_HAS_LIBGFXINIT + select MAINBOARD_USES_IFD_GBE_REGION + select MEMORY_MAPPED_TPM + select NORTHBRIDGE_INTEL_SANDYBRIDGE + select SERIRQ_CONTINUOUS_MODE + select SOUTHBRIDGE_INTEL_C216 + select SUPERIO_NUVOTON_NPCD378 + select USE_NATIVE_RAMINIT + +config CBFS_SIZE + default 0x570000 + +config MAINBOARD_DIR + default "hp/compaq_elite_8300_usdt" + +config MAINBOARD_PART_NUMBER + default "HP Compaq Elite 8300 USDT" + +config VGA_BIOS_ID + default "8086,0152" + +config DRAM_RESET_GATE_GPIO + default 60 + +config USBDEBUG_HCD_INDEX # FIXME: check this + default 2 +endif diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/Kconfig.name b/src/mainboard/hp/compaq_elite_8300_usdt/Kconfig.name new file mode 100644 index 0000000000..030d8560ab --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/Kconfig.name @@ -0,0 +1,2 @@ +config BOARD_HP_COMPAQ_ELITE_8300_USDT + bool "Compaq Elite 8300 USDT" diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/Makefile.inc b/src/mainboard/hp/compaq_elite_8300_usdt/Makefile.inc new file mode 100644 index 0000000000..18391d8b18 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/Makefile.inc @@ -0,0 +1,5 @@ +bootblock-y += early_init.c +bootblock-y += gpio.c +romstage-y += early_init.c +romstage-y += gpio.c +ramstage-$(CONFIG_MAINBOARD_USE_LIBGFXINIT) += gma-mainboard.ads diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/acpi/ec.asl b/src/mainboard/hp/compaq_elite_8300_usdt/acpi/ec.asl new file mode 100644 index 0000000000..73fa78ef14 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/acpi/ec.asl @@ -0,0 +1 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/acpi/platform.asl b/src/mainboard/hp/compaq_elite_8300_usdt/acpi/platform.asl new file mode 100644 index 0000000000..aff432b6f4 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/acpi/platform.asl @@ -0,0 +1,10 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +Method(_WAK, 1) +{ + Return(Package() {0, 0}) +} + +Method(_PTS, 1) +{ +} diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/acpi/superio.asl b/src/mainboard/hp/compaq_elite_8300_usdt/acpi/superio.asl new file mode 100644 index 0000000000..54f8e3fe95 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/acpi/superio.asl @@ -0,0 +1,29 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +/* Copied over from compaq_8200_elite_sff/acpi/superio.asl */ + +#include + +Scope (\_GPE) +{ + Method (_L0D, 0, NotSerialized) + { + Notify (\_SB.PCI0.EHC1, 0x02) + Notify (\_SB.PCI0.EHC2, 0x02) + //FIXME: Add GBE device + //Notify (\_SB.PCI0.GBE, 0x02) + } + + Method (_L09, 0, NotSerialized) + { + Notify (\_SB.PCI0.RP01, 0x02) + Notify (\_SB.PCI0.RP02, 0x02) + Notify (\_SB.PCI0.RP03, 0x02) + Notify (\_SB.PCI0.RP04, 0x02) + Notify (\_SB.PCI0.RP05, 0x02) + Notify (\_SB.PCI0.RP06, 0x02) + Notify (\_SB.PCI0.RP07, 0x02) + Notify (\_SB.PCI0.RP08, 0x02) + Notify (\_SB.PCI0.PEGP, 0x02) + } +} diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/acpi_tables.c b/src/mainboard/hp/compaq_elite_8300_usdt/acpi_tables.c new file mode 100644 index 0000000000..8f4f83b826 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/acpi_tables.c @@ -0,0 +1,12 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include +#include + +void mainboard_fill_gnvs(struct global_nvs *gnvs) +{ + /* Temperature at which OS will shutdown */ + gnvs->tcrt = 100; + /* Temperature at which OS will throttle CPU */ + gnvs->tpsv = 90; +} diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/board_info.txt b/src/mainboard/hp/compaq_elite_8300_usdt/board_info.txt new file mode 100644 index 0000000000..f47ea980b1 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/board_info.txt @@ -0,0 +1,6 @@ +Category: mini +ROM protocol: SPI +ROM socketed: n +ROM package: SOIC-16 +Flashrom support: y +Release year: 2012 diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/cmos.default b/src/mainboard/hp/compaq_elite_8300_usdt/cmos.default new file mode 100644 index 0000000000..6f3cec735e --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/cmos.default @@ -0,0 +1,6 @@ +boot_option=Fallback +debug_level=Debug +power_on_after_fail=Enable +nmi=Enable +sata_mode=AHCI +gfx_uma_size=32M diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/cmos.layout b/src/mainboard/hp/compaq_elite_8300_usdt/cmos.layout new file mode 100644 index 0000000000..bdc06faed6 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/cmos.layout @@ -0,0 +1,73 @@ +## SPDX-License-Identifier: GPL-2.0-only + +# ----------------------------------------------------------------- +entries + +# ----------------------------------------------------------------- +0 120 r 0 reserved_memory + +# ----------------------------------------------------------------- +# RTC_BOOT_BYTE (coreboot hardcoded) +384 1 e 4 boot_option +388 4 h 0 reboot_counter + +# ----------------------------------------------------------------- +# coreboot config options: console +395 4 e 6 debug_level + +# coreboot config options: southbridge +408 1 e 1 nmi +409 2 e 7 power_on_after_fail + +421 1 e 9 sata_mode + +# coreboot config options: northbridge +432 3 e 11 gfx_uma_size + +448 128 r 0 vbnv + +# SandyBridge MRC Scrambler Seed values +896 32 r 0 mrc_scrambler_seed +928 32 r 0 mrc_scrambler_seed_s3 +960 16 r 0 mrc_scrambler_seed_chk + +# coreboot config options: check sums +984 16 h 0 check_sum + +# ----------------------------------------------------------------- + +enumerations + +#ID value text +1 0 Disable +1 1 Enable +2 0 Enable +2 1 Disable +4 0 Fallback +4 1 Normal +6 0 Emergency +6 1 Alert +6 2 Critical +6 3 Error +6 4 Warning +6 5 Notice +6 6 Info +6 7 Debug +6 8 Spew +7 0 Disable +7 1 Enable +7 2 Keep +9 0 AHCI +9 1 IDE +11 0 32M +11 1 64M +11 2 96M +11 3 128M +11 4 160M +11 5 192M +11 6 224M + +# ----------------------------------------------------------------- +checksums + +checksum 392 415 984 diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/devicetree.cb b/src/mainboard/hp/compaq_elite_8300_usdt/devicetree.cb new file mode 100644 index 0000000000..ba4ac6d7f2 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/devicetree.cb @@ -0,0 +1,144 @@ +chip northbridge/intel/sandybridge + register "gpu_dp_b_hotplug" = "4" + register "gpu_dp_c_hotplug" = "4" + device domain 0x0 on + chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH + register "docking_supported" = "0" + register "gen1_dec" = "0x00fc0a01" + register "gen2_dec" = "0x00fc0801" + register "pcie_hotplug_map" = "{ 0, 0, 0, 0, 0, 0, 0, 0 }" + register "pcie_port_coalesce" = "1" + register "sata_interface_speed_support" = "0x3" + register "sata_port_map" = "0x3" # 0x1: 2.5" slot + # 0x2: DVD + # 0x?: mSATA + register "spi_lvscc" = "0x2005" + register "spi_uvscc" = "0x2005" + register "superspeed_capable_ports" = "0x0000000f" + register "xhci_overcurrent_mapping" = "0x00000c03" + register "xhci_switchable_ports" = "0x0000000f" + device ref xhci on # USB 3.0 Controller + subsystemid 0x103c 0x3398 + end + device ref mei1 off # Management Engine Interface 1 + end + device ref gbe on # Intel Gigabit Ethernet + subsystemid 0x103c 0x3398 + end + device ref ehci2 on # USB2 EHCI #2 + subsystemid 0x103c 0x3398 + end + device ref hda on # High Definition Audio + subsystemid 0x103c 0x3398 + end + device ref pcie_rp1 on # Mini-PCIe WLAN + end + device ref ehci1 on # USB2 EHCI #1 + subsystemid 0x103c 0x3398 + end + device ref pci_bridge on # PCI bridge + subsystemid 0x103c 0x3398 + end + device ref lpc on # LPC bridge + chip superio/common # Super I/O grabbed from 8200SFF devicetree + device pnp 2e.ff on # passes SIO base addr to SSDT gen + chip superio/nuvoton/npcd378 + device pnp 2e.0 off end # Floppy + device pnp 2e.1 off end # Parallel + device pnp 2e.2 off # COM1 + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 2e.3 on # COM2, IR + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 2e.4 on # LED control + io 0x60 = 0x600 + # IOBASE[0h] = bit0 LED red / green + # IOBASE[0h] = bit1-4 LED PWM duty cycle + # IOBASE[1h] = bit6 SWCC + + io 0x62 = 0x610 + # IOBASE [0h] = GPES + # IOBASE [1h] = GPEE + # IOBASE [4h:7h] = 32bit upcounter at 1Mhz + # IOBASE [8h:bh] = GPS + # IOBASE [ch:fh] = GPE + end + device pnp 2e.5 on # Mouse + irq 0x70 = 0xc + end + device pnp 2e.6 on # Keyboard + io 0x60 = 0x0060 + io 0x62 = 0x0064 + irq 0x70 = 0x01 + # serialice: Vendor writes: + drq 0xf0 = 0x40 + end + device pnp 2e.7 on # WDT ? + io 0x60 = 0x620 + end + device pnp 2e.8 on # HWM + io 0x60 = 0x800 + # IOBASE[0h:feh] HWM page + # IOBASE[ffh] bit0-bit3 page selector + + drq 0xf0 = 0x20 + drq 0xf1 = 0x01 + drq 0xf2 = 0x40 + drq 0xf3 = 0x01 + + drq 0xf4 = 0x66 + drq 0xf5 = 0x67 + drq 0xf6 = 0x66 + drq 0xf7 = 0x01 + end + device pnp 2e.f on # GPIO OD ? + drq 0xf1 = 0x97 + drq 0xf2 = 0x01 + drq 0xf5 = 0x08 + drq 0xfe = 0x80 + end + device pnp 2e.15 on # BUS ? + io 0x60 = 0x0680 + io 0x62 = 0x0690 + end + device pnp 2e.1c on # Suspend Control ? + io 0x60 = 0x640 + # writing to IOBASE[5h] + # 0x0: Power off + # 0x9: Power off and bricked until CMOS battery removed + end + device pnp 2e.1e on # GPIO ? + io 0x60 = 0x660 + drq 0xf4 = 0x01 + # skip the following, as it + # looks like remapped registers + #drq 0xf5 = 0x06 + #drq 0xf6 = 0x60 + #drq 0xfe = 0x03 + end + end + end + end + chip drivers/pc80/tpm + device pnp 4e.0 on end # TPM module + end + end + device ref sata1 on # SATA Controller 1 + subsystemid 0x103c 0x3398 + end + device ref smbus on # SMBus + subsystemid 0x103c 0x3398 + end + end + device ref host_bridge on # Host bridge Host bridge + subsystemid 0x103c 0x3398 + end + device ref peg10 on end # PEG + device ref igd on # iGPU + subsystemid 0x103c 0x3398 + end + end +end diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/dsdt.asl b/src/mainboard/hp/compaq_elite_8300_usdt/dsdt.asl new file mode 100644 index 0000000000..3a656e8b55 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/dsdt.asl @@ -0,0 +1,30 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include + +#define BRIGHTNESS_UP \_SB.PCI0.GFX0.INCB +#define BRIGHTNESS_DOWN \_SB.PCI0.GFX0.DECB + +DefinitionBlock( + "dsdt.aml", + "DSDT", + ACPI_DSDT_REV_2, + OEM_ID, + ACPI_TABLE_CREATOR, + 0x20141018 /* OEM revision */ +) +{ + #include + #include "acpi/platform.asl" + #include + #include + #include + #include + + Device (\_SB.PCI0) + { + #include + #include + #include + } +} diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/early_init.c b/src/mainboard/hp/compaq_elite_8300_usdt/early_init.c new file mode 100644 index 0000000000..857c25dd19 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/early_init.c @@ -0,0 +1,39 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + + +#include +#include +#include +#include +#include +#include + + +const struct southbridge_usb_port mainboard_usb_ports[] = { + { 1, 0, 0 }, + { 1, 0, 0 }, + { 1, 0, 1 }, + { 1, 0, 1 }, + { 1, 0, 2 }, + { 1, 0, 2 }, + { 1, 0, 3 }, + { 1, 0, 3 }, + { 1, 0, 4 }, + { 1, 0, 4 }, + { 1, 0, 6 }, + { 1, 0, 5 }, + { 1, 0, 5 }, + { 1, 0, 6 }, +}; + +void bootblock_mainboard_early_init(void) +{ + pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x82, 0x1408); + pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x80, 0x0010); +} + +void mainboard_get_spd(spd_raw_data *spd, bool id_only) +{ + read_spd(&spd[3], 0x50, id_only); + read_spd(&spd[1], 0x52, id_only); +} diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/gma-mainboard.ads b/src/mainboard/hp/compaq_elite_8300_usdt/gma-mainboard.ads new file mode 100644 index 0000000000..74b50645e6 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/gma-mainboard.ads @@ -0,0 +1,19 @@ +-- SPDX-License-Identifier: GPL-2.0-or-later + +with HW.GFX.GMA; +with HW.GFX.GMA.Display_Probing; + +use HW.GFX.GMA; +use HW.GFX.GMA.Display_Probing; + +private package GMA.Mainboard is + + ports : constant Port_List := + (DP1, + DP2, + HDMI1, + HDMI2, + Analog, + others => Disabled); + +end GMA.Mainboard; diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/gpio.c b/src/mainboard/hp/compaq_elite_8300_usdt/gpio.c new file mode 100644 index 0000000000..2ae852ae51 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/gpio.c @@ -0,0 +1,191 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include + +static const struct pch_gpio_set1 pch_gpio_set1_mode = { + .gpio0 = GPIO_MODE_GPIO, + .gpio1 = GPIO_MODE_GPIO, + .gpio2 = GPIO_MODE_NATIVE, + .gpio3 = GPIO_MODE_NATIVE, + .gpio4 = GPIO_MODE_NATIVE, + .gpio5 = GPIO_MODE_NATIVE, + .gpio6 = GPIO_MODE_GPIO, + .gpio7 = GPIO_MODE_GPIO, + .gpio8 = GPIO_MODE_GPIO, + .gpio9 = GPIO_MODE_NATIVE, + .gpio10 = GPIO_MODE_NATIVE, + .gpio11 = GPIO_MODE_GPIO, + .gpio12 = GPIO_MODE_NATIVE, + .gpio13 = GPIO_MODE_GPIO, + .gpio14 = GPIO_MODE_NATIVE, + .gpio15 = GPIO_MODE_GPIO, + .gpio16 = GPIO_MODE_GPIO, + .gpio17 = GPIO_MODE_GPIO, + .gpio18 = GPIO_MODE_NATIVE, + .gpio19 = GPIO_MODE_NATIVE, + .gpio20 = GPIO_MODE_NATIVE, + .gpio21 = GPIO_MODE_GPIO, + .gpio22 = GPIO_MODE_GPIO, + .gpio23 = GPIO_MODE_NATIVE, + .gpio24 = GPIO_MODE_GPIO, + .gpio25 = GPIO_MODE_NATIVE, + .gpio26 = GPIO_MODE_NATIVE, + .gpio27 = GPIO_MODE_GPIO, + .gpio28 = GPIO_MODE_GPIO, + .gpio29 = GPIO_MODE_GPIO, + .gpio30 = GPIO_MODE_NATIVE, + .gpio31 = GPIO_MODE_GPIO, +}; + +static const struct pch_gpio_set1 pch_gpio_set1_direction = { + .gpio0 = GPIO_DIR_INPUT, + .gpio1 = GPIO_DIR_INPUT, + .gpio6 = GPIO_DIR_INPUT, + .gpio7 = GPIO_DIR_INPUT, + .gpio8 = GPIO_DIR_INPUT, + .gpio11 = GPIO_DIR_INPUT, + .gpio13 = GPIO_DIR_INPUT, + .gpio15 = GPIO_DIR_OUTPUT, + .gpio16 = GPIO_DIR_INPUT, + .gpio17 = GPIO_DIR_OUTPUT, + .gpio21 = GPIO_DIR_INPUT, + .gpio22 = GPIO_DIR_INPUT, + .gpio24 = GPIO_DIR_INPUT, + .gpio27 = GPIO_DIR_INPUT, + .gpio28 = GPIO_DIR_OUTPUT, + .gpio29 = GPIO_DIR_OUTPUT, + .gpio31 = GPIO_DIR_INPUT, +}; + +static const struct pch_gpio_set1 pch_gpio_set1_level = { + .gpio15 = GPIO_LEVEL_LOW, + .gpio17 = GPIO_LEVEL_LOW, + .gpio28 = GPIO_LEVEL_LOW, + .gpio29 = GPIO_LEVEL_HIGH, +}; + +static const struct pch_gpio_set1 pch_gpio_set1_reset = { +}; + +static const struct pch_gpio_set1 pch_gpio_set1_invert = { + .gpio0 = GPIO_INVERT, + .gpio1 = GPIO_INVERT, + .gpio6 = GPIO_INVERT, + .gpio11 = GPIO_INVERT, + .gpio13 = GPIO_INVERT, +}; + +static const struct pch_gpio_set1 pch_gpio_set1_blink = { +}; + +static const struct pch_gpio_set2 pch_gpio_set2_mode = { + .gpio32 = GPIO_MODE_GPIO, + .gpio33 = GPIO_MODE_GPIO, + .gpio34 = GPIO_MODE_GPIO, + .gpio35 = GPIO_MODE_GPIO, + .gpio36 = GPIO_MODE_GPIO, + .gpio37 = GPIO_MODE_GPIO, + .gpio38 = GPIO_MODE_GPIO, + .gpio39 = GPIO_MODE_GPIO, + .gpio40 = GPIO_MODE_NATIVE, + .gpio41 = GPIO_MODE_NATIVE, + .gpio42 = GPIO_MODE_NATIVE, + .gpio43 = GPIO_MODE_GPIO, + .gpio44 = GPIO_MODE_NATIVE, + .gpio45 = GPIO_MODE_NATIVE, + .gpio46 = GPIO_MODE_GPIO, + .gpio47 = GPIO_MODE_NATIVE, + .gpio48 = GPIO_MODE_GPIO, + .gpio49 = GPIO_MODE_GPIO, + .gpio50 = GPIO_MODE_NATIVE, + .gpio51 = GPIO_MODE_NATIVE, + .gpio52 = GPIO_MODE_NATIVE, + .gpio53 = GPIO_MODE_NATIVE, + .gpio54 = GPIO_MODE_GPIO, + .gpio55 = GPIO_MODE_NATIVE, + .gpio56 = GPIO_MODE_NATIVE, + .gpio57 = GPIO_MODE_GPIO, + .gpio58 = GPIO_MODE_NATIVE, + .gpio59 = GPIO_MODE_NATIVE, + .gpio60 = GPIO_MODE_NATIVE, + .gpio61 = GPIO_MODE_GPIO, + .gpio62 = GPIO_MODE_NATIVE, + .gpio63 = GPIO_MODE_NATIVE, +}; + +static const struct pch_gpio_set2 pch_gpio_set2_direction = { + .gpio32 = GPIO_DIR_INPUT, + .gpio33 = GPIO_DIR_INPUT, + .gpio34 = GPIO_DIR_INPUT, + .gpio35 = GPIO_DIR_INPUT, + .gpio36 = GPIO_DIR_INPUT, + .gpio37 = GPIO_DIR_INPUT, + .gpio38 = GPIO_DIR_INPUT, + .gpio39 = GPIO_DIR_INPUT, + .gpio43 = GPIO_DIR_INPUT, + .gpio46 = GPIO_DIR_INPUT, + .gpio48 = GPIO_DIR_INPUT, + .gpio49 = GPIO_DIR_INPUT, + .gpio54 = GPIO_DIR_INPUT, + .gpio57 = GPIO_DIR_INPUT, + .gpio61 = GPIO_DIR_INPUT, +}; + +static const struct pch_gpio_set2 pch_gpio_set2_level = { +}; + +static const struct pch_gpio_set2 pch_gpio_set2_reset = { +}; + +static const struct pch_gpio_set3 pch_gpio_set3_mode = { + .gpio64 = GPIO_MODE_NATIVE, + .gpio65 = GPIO_MODE_NATIVE, + .gpio66 = GPIO_MODE_NATIVE, + .gpio67 = GPIO_MODE_NATIVE, + .gpio68 = GPIO_MODE_GPIO, + .gpio69 = GPIO_MODE_GPIO, + .gpio70 = GPIO_MODE_GPIO, + .gpio71 = GPIO_MODE_GPIO, + .gpio72 = GPIO_MODE_GPIO, + .gpio73 = GPIO_MODE_NATIVE, + .gpio74 = GPIO_MODE_NATIVE, + .gpio75 = GPIO_MODE_NATIVE, +}; + +static const struct pch_gpio_set3 pch_gpio_set3_direction = { + .gpio68 = GPIO_DIR_INPUT, + .gpio69 = GPIO_DIR_INPUT, + .gpio70 = GPIO_DIR_INPUT, + .gpio71 = GPIO_DIR_OUTPUT, + .gpio72 = GPIO_DIR_INPUT, +}; + +static const struct pch_gpio_set3 pch_gpio_set3_level = { + .gpio71 = GPIO_LEVEL_LOW, +}; + +static const struct pch_gpio_set3 pch_gpio_set3_reset = { +}; + +const struct pch_gpio_map mainboard_gpio_map = { + .set1 = { + .mode = &pch_gpio_set1_mode, + .direction = &pch_gpio_set1_direction, + .level = &pch_gpio_set1_level, + .blink = &pch_gpio_set1_blink, + .invert = &pch_gpio_set1_invert, + .reset = &pch_gpio_set1_reset, + }, + .set2 = { + .mode = &pch_gpio_set2_mode, + .direction = &pch_gpio_set2_direction, + .level = &pch_gpio_set2_level, + .reset = &pch_gpio_set2_reset, + }, + .set3 = { + .mode = &pch_gpio_set3_mode, + .direction = &pch_gpio_set3_direction, + .level = &pch_gpio_set3_level, + .reset = &pch_gpio_set3_reset, + }, +}; diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/hda_verb.c b/src/mainboard/hp/compaq_elite_8300_usdt/hda_verb.c new file mode 100644 index 0000000000..a0c534c198 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/hda_verb.c @@ -0,0 +1,32 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include + +const u32 cim_verb_data[] = { + 0x10ec0221, /* Codec Vendor / Device ID: Realtek */ + 0x103c3398, /* Subsystem ID */ + 11, /* Number of 4 dword sets */ + AZALIA_SUBVENDOR(0, 0x103c3398), + AZALIA_PIN_CFG(0, 0x12, 0x411111f0), + AZALIA_PIN_CFG(0, 0x14, 0x01014020), + AZALIA_PIN_CFG(0, 0x17, 0x90170110), + AZALIA_PIN_CFG(0, 0x18, 0x411111f0), + AZALIA_PIN_CFG(0, 0x19, 0x411111f0), + AZALIA_PIN_CFG(0, 0x1a, 0x02a11c3f), + AZALIA_PIN_CFG(0, 0x1b, 0x01813c30), + AZALIA_PIN_CFG(0, 0x1d, 0x598301f0), + AZALIA_PIN_CFG(0, 0x1e, 0x411111f0), + AZALIA_PIN_CFG(0, 0x21, 0x0221102f), + + 0x80862806, /* Codec Vendor / Device ID: Intel */ + 0x80860101, /* Subsystem ID */ + 4, /* Number of 4 dword sets */ + AZALIA_SUBVENDOR(3, 0x80860101), + AZALIA_PIN_CFG(3, 0x05, 0x18560010), + AZALIA_PIN_CFG(3, 0x06, 0x18560020), + AZALIA_PIN_CFG(3, 0x07, 0x58560030), +}; + +const u32 pc_beep_verbs[0] = {}; + +AZALIA_ARRAY_SIZES; diff --git a/src/mainboard/hp/compaq_elite_8300_usdt/mainboard.c b/src/mainboard/hp/compaq_elite_8300_usdt/mainboard.c new file mode 100644 index 0000000000..8dbd95ef96 --- /dev/null +++ b/src/mainboard/hp/compaq_elite_8300_usdt/mainboard.c @@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include +#include +#include + +static void mainboard_enable(struct device *dev) +{ + install_intel_vga_int15_handler(GMA_INT15_ACTIVE_LFP_NONE, + GMA_INT15_PANEL_FIT_DEFAULT, + GMA_INT15_BOOT_DISPLAY_DEFAULT, 0); +} + +struct chip_operations mainboard_ops = { + .enable_dev = mainboard_enable, +};