diff --git a/src/cpu/p6/Config.lb b/src/cpu/p6/Config.lb index d4918f9147..8242a6e874 100644 --- a/src/cpu/p6/Config.lb +++ b/src/cpu/p6/Config.lb @@ -1,5 +1,10 @@ uses INTEL_PPRO_MTRR +uses CPU_FIXUP dir /cpu/p5 -object cpufixup.o +config chip.h +if CPU_FIXUP + object cpufixup.o + object apic_timer.o +end object mtrr.o object pgtbl.o diff --git a/src/cpu/p6/apic_timer.c b/src/cpu/p6/apic_timer.c new file mode 100644 index 0000000000..fa7e9b905f --- /dev/null +++ b/src/cpu/p6/apic_timer.c @@ -0,0 +1,26 @@ +#include +#include +#include +#include + +void init_timer(void) +{ + /* Set the apic timer to no interrupts and periodic mode */ + apic_write(APIC_LVTT, (1 << 17)|(1<< 16)|(0 << 12)|(0 << 0)); + /* Set the divider to 1, no divider */ + apic_write(APIC_TDCR, APIC_TDR_DIV_1); + /* Set the initial counter to 0xffffffff */ + apic_write(APIC_TMICT, 0xffffffff); +} + +void udelay(unsigned usecs) +{ + uint32_t start, value, ticks; + /* Calculate the number of ticks to run, our FSB runs a 200Mhz */ + ticks = usecs * 200; + start = apic_read(APIC_TMCCT); + do { + value = apic_read(APIC_TMCCT); + } while((start - value) < ticks); + +} diff --git a/src/cpu/p6/chip.h b/src/cpu/p6/chip.h new file mode 100644 index 0000000000..bfcdf79ed7 --- /dev/null +++ b/src/cpu/p6/chip.h @@ -0,0 +1,5 @@ +extern struct chip_control cpu_p6_control; + +struct cpu_p6_config { + int nothing; +}; diff --git a/src/cpu/p6/cpufixup.c b/src/cpu/p6/cpufixup.c index e5cd3fc017..f611524fab 100644 --- a/src/cpu/p6/cpufixup.c +++ b/src/cpu/p6/cpufixup.c @@ -351,3 +351,27 @@ void p6_cpufixup(struct mem_range *mem) printk_debug("Updating microcode\n"); display_cpuid_update_microcode(); } + + +static +void p6_enable(struct chip *chip, enum chip_pass pass) +{ + + struct cpu_p6_config *conf = (struct cpu_p6_config *)chip->chip_info; + + switch (pass) { + case CONF_PASS_PRE_CONSOLE: + break; + case CONF_PASS_PRE_PCI: + init_timer(); + break; + default: + /* nothing yet */ + break; + } +} + +struct chip_control cpu_p6_control = { + .enable = p6_enable, + .name = "Intel P6 CPU", +}; diff --git a/src/cpu/p6/disable_mmx_sse.inc b/src/cpu/p6/disable_mmx_sse.inc new file mode 100644 index 0000000000..5ce9dfdc1f --- /dev/null +++ b/src/cpu/p6/disable_mmx_sse.inc @@ -0,0 +1,27 @@ + /* Clear out an mmx state */ + emms + + /* + * Put the processor back into a reset state + * with respect to the xmm registers. + */ + + pxor %xmm0, %xmm0 + pxor %xmm1, %xmm1 + pxor %xmm2, %xmm2 + pxor %xmm3, %xmm3 + pxor %xmm4, %xmm4 + pxor %xmm5, %xmm5 + pxor %xmm6, %xmm6 + pxor %xmm7, %xmm7 + + /* Disable floating point emulation */ + movl %cr0, %eax + andl $~(1<<2), %eax + movl %eax, %cr0 + + /* Disable sse instructions */ + movl %cr4, %eax + andl $~(3<<9), %eax + movl %eax, %cr4 + diff --git a/src/cpu/p6/enable_mmx_sse.inc b/src/cpu/p6/enable_mmx_sse.inc new file mode 100644 index 0000000000..f0b2487b8c --- /dev/null +++ b/src/cpu/p6/enable_mmx_sse.inc @@ -0,0 +1,25 @@ + /* Save the BIST result */ + movl %eax, %ebp + + /* + * Enabling mmx registers is a noop + * Enable the use of the xmm registers + */ + + /* Enable sse instructions */ + movl %cr4, %eax + orl $(1<<9), %eax + movl %eax, %cr4 + + /* Disable floating point emulation */ + movl %cr0, %eax + andl $~(1<<2), %eax + movl %eax, %cr0 + + /* enable sse extension */ + movl %cr0, %eax + andl $~(1<<1), %eax + movl %eax, %cr0 + + /* Restore the BIST result */ + movl %ebp, %eax diff --git a/src/include/device/pci_ids.h b/src/include/device/pci_ids.h index 586083a966..eeab66cc16 100644 --- a/src/include/device/pci_ids.h +++ b/src/include/device/pci_ids.h @@ -1890,6 +1890,20 @@ #define PCI_DEVICE_ID_INTEL_82801CA_1F5 0x2485 #define PCI_DEVICE_ID_INTEL_82801CA_1D2 0x2487 +#define PCI_DEVICE_ID_INTEL_82801ER_1E0 0x244e +#define PCI_DEVICE_ID_INTEL_82801ER_1F0 0x24d0 +#define PCI_DEVICE_ID_INTEL_82801ER_1F1 0x24db +#define PCI_DEVICE_ID_INTEL_82801ER_1F2 0x24d1 +#define PCI_DEVICE_ID_INTEL_82801ER_1F2_R 0x24df +#define PCI_DEVICE_ID_INTEL_82801ER_1F3 0x24d3 +#define PCI_DEVICE_ID_INTEL_82801ER_1F5 0x24d5 +#define PCI_DEVICE_ID_INTEL_82801ER_1F6 0x24d6 +#define PCI_DEVICE_ID_INTEL_82801ER_1D0 0x24d2 +#define PCI_DEVICE_ID_INTEL_82801ER_1D1 0x24d4 +#define PCI_DEVICE_ID_INTEL_82801ER_1D2 0x24d7 +#define PCI_DEVICE_ID_INTEL_82801ER_1D3 0x24de +#define PCI_DEVICE_ID_INTEL_82801ER_1D7 0x24dd + #define PCI_DEVICE_ID_INTEL_82870_1E0 0x1461 #define PCI_DEVICE_ID_INTEL_82870_1F0 0x1460 diff --git a/src/mainboard/tyan/s2735/Config.lb b/src/mainboard/tyan/s2735/Config.lb new file mode 100644 index 0000000000..2b94689ba6 --- /dev/null +++ b/src/mainboard/tyan/s2735/Config.lb @@ -0,0 +1,222 @@ +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD +uses ARCH +uses HARD_RESET_BUS +uses HARD_RESET_DEVICE +uses HARD_RESET_FUNCTION +# +# +### +### Set all of the defaults for an x86 architecture +### +# +# +### +### Build the objects we have code for in this directory. +### +##object mainboard.o +config chip.h +register "fixup_scsi" = "1" +register "fixup_vga" = "1" + + +## +## Move the default LinuxBIOS cmos range off of AMD RTC registers +## +default LB_CKS_RANGE_START=49 +default LB_CKS_RANGE_END=122 +default LB_CKS_LOC=123 + +driver mainboard.o +#dir /drvers/adaptec/7902 +#dir /drivers/si/3114 +#dir /drivers/intel/82551_ipmi +#dir /drivers/ati/ragexl +if HAVE_MP_TABLE object mptable.o end +if HAVE_PIRQ_TABLE object irq_tables.o end +# +#default HARD_RESET_BUS=1 +#default HARD_RESET_DEVICE=4 +#default HARD_RESET_FUNCTION=0 +# +arch i386 end +# +### +### Build our 16 bit and 32 bit linuxBIOS entry code +### +mainboardinit cpu/i386/entry16.inc +mainboardinit cpu/i386/entry32.inc +mainboardinit cpu/i386/bist32.inc +ldscript /cpu/i386/entry16.lds +ldscript /cpu/i386/entry32.lds +# +### +### Build our reset vector (This is where linuxBIOS is entered) +### +if USE_FALLBACK_IMAGE + mainboardinit cpu/i386/reset16.inc + ldscript /cpu/i386/reset16.lds +else + mainboardinit cpu/i386/reset32.inc + ldscript /cpu/i386/reset32.lds +end +# +#### Should this be in the northbridge code? +mainboardinit arch/i386/lib/cpu_reset.inc +# +### +### Include an id string (For safe flashing) +### +mainboardinit arch/i386/lib/id.inc +ldscript /arch/i386/lib/id.lds +# +#### +#### This is the early phase of linuxBIOS startup +#### Things are delicate and we test to see if we should +#### failover to another image. +#### +#option MAX_REBOOT_CNT=2 +if USE_FALLBACK_IMAGE + ldscript /arch/i386/lib/failover.lds +end +# +### +### Setup our mtrrs +### +#mainboardinit cpu/p6/earlymtrr.inc +### +### Only the bootstrap cpu makes it here. +### Failover if we need to +### +# +if USE_FALLBACK_IMAGE + mainboardinit ./failover.inc +end + +# +# +### +### Setup the serial port +### +mainboardinit pc80/serial.inc +mainboardinit arch/i386/lib/console.inc +mainboardinit cpu/i386/bist32_fail.inc +# +#### +#### O.k. We aren't just an intermediary anymore! +#### +# +### +### When debugging disable the watchdog timer +### +##option MAXIMUM_CONSOLE_LOGLEVEL=7 +#default MAXIMUM_CONSOLE_LOGLEVEL=7 +# +#if USE_FALLBACK_IMAGE mainboardinit arch/i386/lib/noop_failover.inc end +# +### +### Romcc output +### + +makerule ./failover.E + depends "$(MAINBOARD)/failover.c" + action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E" +end + +makerule ./failover.inc + depends "./romcc ./failover.E" + action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E" +end + +makerule ./auto.E + depends "$(MAINBOARD)/auto.c option_table.h" + action "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E" +end +makerule ./auto.inc + depends "./romcc ./auto.E" + action "./romcc -O2 -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E" +# action "./romcc -O2 ./auto.E > auto.inc" +end +mainboardinit cpu/p6/enable_mmx_sse.inc +mainboardinit ./auto.inc +mainboardinit cpu/p6/disable_mmx_sse.inc +# +### +### Include the secondary Configuration files +### + +config chip.h + +northbridge intel/e7501 "e7501" + pci 0:2.0 + pci 0:0.0 + pci 0:0.1 + pci 0:6.0 + southbridge intel/i82870 "i82870" + pci 0:1c.0 + pci 0:1d.0 + pci 0:1e.0 + pci 0:1f.0 + end +end + southbridge intel/i82801er "i82801er" + pci 0:1f.0 + pci 0:1d.0 on + pci 0:1d.1 on + pci 0:1d.2 on + pci 0:1d.3 on + pci 0:1d.7 on + pci 0:1e.0 on + pci 0:1f.1 off + pci 0:1f.2 on + pci 0:1f.3 on + pci 0:1f.5 off + pci 0:1f.6 off +# pci 1:8.0 off + superio winbond/w83627hf + pnp 2e.0 on # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + pnp 2e.1 off # Parallel Port + io 0x60 = 0x378 + irq 0x70 = 7 + pnp 2e.2 on # Com1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + pnp 2e.3 off # Com2 + io 0x60 = 0x2f8 + irq 0x70 = 3 + pnp 2e.5 on # Keyboard + io 0x60 = 0x60 + io 0x62 = 0x64 + irq 0x70 = 1 + irq 0x72 = 12 + pnp 2e.6 off # CIR + pnp 2e.7 off # GAME_MIDI_GIPO1 + pnp 2e.8 off # GPIO2 + pnp 2e.9 off # GPIO3 + pnp 2e.a off # ACPI + pnp 2e.b on # HW Monitor + io 0x60 = 0x290 + end + end +#end +dir /pc80 +#dir /bioscall +cpu p6 "cpu0" +end + +cpu p6 "cpu1" +end + +cpu p6 "cpu2" +end + +cpu p6 "cpu3" +end diff --git a/src/mainboard/tyan/s2735/auto.c b/src/mainboard/tyan/s2735/auto.c new file mode 100644 index 0000000000..3a99aa29a9 --- /dev/null +++ b/src/mainboard/tyan/s2735/auto.c @@ -0,0 +1,135 @@ +#define ASSEMBLY 1 +#include +#include +#include +#include +#include +#include +#include "option_table.h" +#include "pc80/mc146818rtc_early.c" +#include "pc80/serial.c" +#include "arch/i386/lib/console.c" +#include "ram/ramtest.c" +#include "southbridge/intel/i82801er/i82801er_early_smbus.c" +#include "northbridge/intel/e7501/raminit.h" + +#if 1 +#include "cpu/p6/apic_timer.c" +#include "lib/delay.c" +#endif + +#include "cpu/p6/boot_cpu.c" +#include "northbridge/intel/e7501/debug.c" +#include "superio/winbond/w83627hf/w83627hf_early_serial.c" + +#include "cpu/p6/earlymtrr.c" + +#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1) + +static void hard_reset(void) +{ + outb(0x0e, 0x0cf9); +} + +static void memreset_setup(void) +{ +} + +static void memreset(int controllers, const struct mem_controller *ctrl) +{ +} + + + +static inline void activate_spd_rom(const struct mem_controller *ctrl) +{ + /* nothing to do */ +} + +static inline int spd_read_byte(unsigned device, unsigned address) +{ + return smbus_read_byte(device, address); +} + +#include "northbridge/intel/e7501/raminit.c" +#include "northbridge/intel/e7501/reset_test.c" +#include "sdram/generic_sdram.c" + +static void main(void) +{ + static const struct mem_controller memctrl[] = { + { + .d0 = PCI_DEV(0, 0, 0), + .d0f1 = PCI_DEV(0, 0, 1), + .channel0 = { (0xa<<3)|0, (0xa<<3)|1, (0xa<<3)|2, 0 }, + .channel1 = { (0xa<<3)|4, (0xa<<3)|5, (0xa<<3)|6, 0 }, + }, + }; + +#if 1 + enable_lapic(); + init_timer(); +#endif + + w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE); + uart_init(); + console_init(); +// setup_default_resource_map(); +#if 0 + print_pci_devices(); +#endif + if(!bios_reset_detected()) { + enable_smbus(); +#if 0 +// dump_spd_registers(&memctrl[0]); + dump_smbus_registers(); +#endif + + memreset_setup(); + sdram_initialize(sizeof(memctrl)/sizeof(memctrl[0]), memctrl); + } +#if 0 + else { + /* clear memory 1meg */ + __asm__ volatile( + "1: \n\t" + "movl %0, %%fs:(%1)\n\t" + "addl $4,%1\n\t" + "subl $4,%2\n\t" + "jnz 1b\n\t" + : + : "a" (0), "D" (0), "c" (1024*1024) + ); + + } +#endif + +#if 0 + dump_pci_devices(); +#endif +#if 0 + dump_pci_device(PCI_DEV(0, 0, 0)); +#endif + +#if 0 + msr_t msr; + msr = rdmsr(TOP_MEM2); + print_debug("TOP_MEM2: "); + print_debug_hex32(msr.hi); + print_debug_hex32(msr.lo); + print_debug("\r\n"); +#endif +/* +#if 0 + ram_check(0x00000000, msr.lo+(msr.hi<<32)); +#else +#if 0 + // Check 16MB of memory @ 0 + ram_check(0x00000000, 0x01000000); +#else + // Check 16MB of memory @ 2GB + ram_check(0x80000000, 0x81000000); +#endif +#endif +*/ +} diff --git a/src/mainboard/tyan/s2735/chip.h b/src/mainboard/tyan/s2735/chip.h new file mode 100644 index 0000000000..f3a2ec6962 --- /dev/null +++ b/src/mainboard/tyan/s2735/chip.h @@ -0,0 +1,6 @@ +extern struct chip_control mainboard_tyan_s2735_control; + +struct mainboard_tyan_s2735_config { + int fixup_scsi; + int fixup_vga; +}; diff --git a/src/mainboard/tyan/s2735/cmos.layout b/src/mainboard/tyan/s2735/cmos.layout new file mode 100644 index 0000000000..2252e6720c --- /dev/null +++ b/src/mainboard/tyan/s2735/cmos.layout @@ -0,0 +1,96 @@ +entries + +#start-bit length config config-ID name +#0 8 r 0 seconds +#8 8 r 0 alarm_seconds +#16 8 r 0 minutes +#24 8 r 0 alarm_minutes +#32 8 r 0 hours +#40 8 r 0 alarm_hours +#48 8 r 0 day_of_week +#56 8 r 0 day_of_month +#64 8 r 0 month +#72 8 r 0 year +#80 4 r 0 rate_select +#84 3 r 0 REF_Clock +#87 1 r 0 UIP +#88 1 r 0 auto_switch_DST +#89 1 r 0 24_hour_mode +#90 1 r 0 binary_values_enable +#91 1 r 0 square-wave_out_enable +#92 1 r 0 update_finished_enable +#93 1 r 0 alarm_interrupt_enable +#94 1 r 0 periodic_interrupt_enable +#95 1 r 0 disable_clock_updates +#96 288 r 0 temporary_filler +0 384 r 0 reserved_memory +384 1 e 4 boot_option +385 1 e 4 last_boot +386 1 e 1 ECC_memory +388 4 r 0 reboot_bits +392 3 e 5 baud_rate +395 1 e 2 hyper_threading +396 1 e 1 thermal_monitoring +397 1 e 1 remap_memory_high +400 1 e 1 power_on_after_fail +412 4 e 6 debug_level +416 4 e 7 boot_first +420 4 e 7 boot_second +424 4 e 7 boot_third +428 4 h 0 boot_index +432 8 h 0 boot_countdown +#440 4 e 9 slow_cpu +444 1 e 1 nmi +728 256 h 0 user_data +984 16 h 0 check_sum +# Reserve the extended AMD configuration registers +1000 24 r 0 reserved_memory + + + +enumerations + +#ID value text +1 0 Disable +1 1 Enable +2 0 Enable +2 1 Disable +4 0 Fallback +4 1 Normal +5 0 115200 +5 1 57600 +5 2 38400 +5 3 19200 +5 4 9600 +5 5 4800 +5 6 2400 +5 7 1200 +6 6 Notice +6 7 Info +6 8 Debug +6 9 Spew +7 0 Network +7 1 HDD +7 2 Floppy +7 8 Fallback_Network +7 9 Fallback_HDD +7 10 Fallback_Floppy +#7 3 ROM +#8 0 200Mhz +#8 1 166Mhz +#8 2 133Mhz +#8 3 100Mhz +#9 0 off +#9 1 87.5% +#9 2 75.0% +#9 3 62.5% +#9 4 50.0% +#9 5 37.5% +#9 6 25.0% +#9 7 12.5% + +checksums + +checksum 392 983 984 + + diff --git a/src/mainboard/tyan/s2735/failover.c b/src/mainboard/tyan/s2735/failover.c new file mode 100644 index 0000000000..6ba3cae62a --- /dev/null +++ b/src/mainboard/tyan/s2735/failover.c @@ -0,0 +1,59 @@ +#define ASSEMBLY 1 +#include +#include +#include +#include +#include +#include +#include "pc80/mc146818rtc_early.c" +#include "southbridge/intel/i82801er/cmos_failover.c" +#include "cpu/p6/boot_cpu.c" +#include "northbridge/intel/e7501/reset_test.c" + +#define HAVE_REGPARM_SUPPORT 0 +#if HAVE_REGPARM_SUPPORT +static unsigned long main(unsigned long bist) +{ +#else +static void main(void) +{ + unsigned long bist = 0; + +#endif + /* Is this a deliberate reset by the bios */ + if (bios_reset_detected() && last_boot_normal()) { + goto normal_image; + } + /* This is the primary cpu how should I boot? */ + else { + + check_cmos_failed(); + + if (do_normal_boot()) { + goto normal_image; + } + else { + goto fallback_image; + } + } + normal_image: + asm volatile ("jmp __normal_image" + : /* outputs */ + : "a" (bist) /* inputs */ + : /* clobbers */ + ); +#if 0 + cpu_reset: + asm volatile ("jmp __cpu_reset" + : /* outputs */ + : "a"(bist) /* inputs */ + : /* clobbers */ + ); +#endif + fallback_image: +#if HAVE_REGPARM_SUPPORT + return bist; +#else + return; +#endif +} diff --git a/src/mainboard/tyan/s2735/irq_tables.c b/src/mainboard/tyan/s2735/irq_tables.c new file mode 100644 index 0000000000..b85847e9aa --- /dev/null +++ b/src/mainboard/tyan/s2735/irq_tables.c @@ -0,0 +1,40 @@ +/* This file was generated by getpir.c, do not modify! + (but if you do, please run checkpir on it to verify) + Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up + + Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM +*/ + +#include + +const struct irq_routing_table intel_irq_routing_table = { + PIRQ_SIGNATURE, /* u32 signature */ + PIRQ_VERSION, /* u16 version */ + 32+16*15, /* there can be total 15 devices on the bus */ + 0x00, /* Where the interrupt router lies (bus) */ + (0x1f<<3)|0x0, /* Where the interrupt router lies (dev) */ + 0, /* IRQs devoted exclusively to PCI usage */ + 0x8086, /* Vendor */ + 0x24d0, /* Device */ + 0, /* Crap (miniport) */ + { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */ + 0x9a, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */ + { + /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */ + {0x04,(0x08<<3)|0x0, {{0x68, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, + {0x00,(0x1f<<3)|0x0, {{0x62, 0xdcf8}, {0x61, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, + {0x00,(0x1d<<3)|0x0, {{0x60, 0xdcf8}, {0x63, 0xdcf8}, {0x62, 0xdcf8}, {0x6b, 0x0dcf8}}, 0x0, 0x0}, + {0x04,(0x03<<3)|0x0, {{0x62, 0xdcf8}, {0x63, 0xdcf8}, {0x60, 0xdcf8}, {0x61, 0x0dcf8}}, 0x3, 0x0}, + {0x04,(0x02<<3)|0x0, {{0x62, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, + {0x03,(0x1f<<3)|0x0, {{0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, + {0x02,(0x1f<<3)|0x0, {{0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, + {0x03,(0x03<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x1, 0x0}, + {0x03,(0x06<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x2, 0x0}, + {0x02,(0x01<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, + {0x02,(0x02<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, + {0x04,(0x01<<3)|0x0, {{0x61, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0}, + {0x04,(0x04<<3)|0x0, {{0x63, 0xdcf8}, {0x60, 0xdcf8}, {0x61, 0xdcf8}, {0x62, 0x0dcf8}}, 0x4, 0x0}, + {0x03,(0x04<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x5, 0x0}, + {0x03,(0x05<<3)|0x0, {{0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0xdcf8}, {0x60, 0x0dcf8}}, 0x6, 0x0}, + } +}; diff --git a/src/mainboard/tyan/s2735/mainboard.c b/src/mainboard/tyan/s2735/mainboard.c new file mode 100644 index 0000000000..143909f1a5 --- /dev/null +++ b/src/mainboard/tyan/s2735/mainboard.c @@ -0,0 +1,183 @@ +#include +#include +#include +#include +#include +#include +#include "chip.h" +//#include +//#include "lsi_scsi.c" +unsigned long initial_apicid[CONFIG_MAX_CPUS] = +{ + 0, 6, 1, 7 +}; +#if 0 +static void fixup_lsi_53c1030(struct device *pdev) +{ +// uint8_t byte; + uint16_t word; + + byte = 1; + pci_write_config8(pdev, 0xff, byte); + // Set the device id +// pci_write_config_word(pdev, PCI_DEVICE_ID, PCI_DEVICE_ID_LSILOGIC_53C1030); + // Set the subsytem vendor id +// pci_write_config16(pdev, PCI_SUBSYSTEM_VENDOR_ID, PCI_VENDOR_ID_TYAN); + word = 0x10f1; + pci_write_config16(pdev, PCI_SUBSYSTEM_VENDOR_ID, word); + // Set the subsytem id + word = 0x2880; + pci_write_config16(pdev, PCI_SUBSYSTEM_ID, word); + // Disable writes to the device id + byte = 0; + pci_write_config8(pdev, 0xff, byte); + +// lsi_scsi_init(pdev); + +} +#endif +//extern static void lsi_scsi_init(struct device *dev); +#if 0 +static void print_pci_regs(struct device *dev) +{ + uint8_t byte; + int i; + + for(i=0;i<256;i++) { + byte = pci_read_config8(dev, i); + + if((i%16)==0) printk_info("\n%02x:",i); + printk_debug(" %02x",byte); + } + printk_debug("\n"); + +// pci_write_config8(dev, 0x4, byte); + +} +#endif +#if 0 +static void print_mem(void) +{ + int i; + int low_1MB = 0; + for(i=low_1MB;ichip_info; + + switch (pass) { + default: break; +// case CONF_PASS_PRE_CONSOLE: +// case CONF_PASS_PRE_PCI: + case CONF_PASS_POST_PCI: + case CONF_PASS_PRE_BOOT: +// if (conf->fixup_scsi) +// onboard_scsi_fixup(); +// if (conf->fixup_vga) +// vga_fixup(); +// printk_debug("mainboard fixup pass %d done\r\n",pass); + break; + } + +} + +static int +mainboard_scan_bus(device_t root, int maxbus) +{ + int retval; + printk_spew("%s: root %p maxbus %d\n", __FUNCTION__, root, maxbus); + retval = pci_scan_bus(root->bus, 0, 0xff, maxbus); + printk_spew("DONE %s: return %d\n", __FUNCTION__, maxbus); + return maxbus; +} + +static struct device_operations mainboard_operations = { + .read_resources = root_dev_read_resources, + .set_resources = root_dev_set_resources, + .enable_resources = enable_childrens_resources, + .init = 0, + .scan_bus = mainboard_scan_bus, + .enable = 0, +}; + +static void enumerate(struct chip *chip) +{ + struct chip *child; + dev_root.ops = &mainboard_operations; + chip->dev = &dev_root; + chip->bus = 0; + for(child = chip->children; child; child = child->next) { + child->bus = &dev_root.link[0]; + } +} +struct chip_control mainboard_tyan_s2735_control = { + .enable = enable, + .enumerate = enumerate, + .name = "Tyan s2735 mainboard ", +}; + diff --git a/src/mainboard/tyan/s2735/mptable.c b/src/mainboard/tyan/s2735/mptable.c new file mode 100644 index 0000000000..25b1929eba --- /dev/null +++ b/src/mainboard/tyan/s2735/mptable.c @@ -0,0 +1,165 @@ +#include +#include +#include +#include +#include + +void *smp_write_config_table(void *v, unsigned long * processor_map) +{ + static const char sig[4] = "PCMP"; + static const char oem[8] = "TYAN "; + static const char productid[12] = "S2735 "; + struct mp_config_table *mc; + + mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); + memset(mc, 0, sizeof(*mc)); + + memcpy(mc->mpc_signature, sig, sizeof(sig)); + mc->mpc_length = sizeof(*mc); /* initially just the header */ + mc->mpc_spec = 0x04; + mc->mpc_checksum = 0; /* not yet computed */ + memcpy(mc->mpc_oem, oem, sizeof(oem)); + memcpy(mc->mpc_productid, productid, sizeof(productid)); + mc->mpc_oemptr = 0; + mc->mpc_oemsize = 0; + mc->mpc_entry_count = 0; /* No entries yet... */ + mc->mpc_lapic = LAPIC_ADDR; + mc->mpe_length = 0; + mc->mpe_checksum = 0; + mc->reserved = 0; + + smp_write_processors(mc, processor_map); + + +/*Bus: Bus ID Type*/ + smp_write_bus(mc, 0, "PCI "); + smp_write_bus(mc, 1, "PCI "); + smp_write_bus(mc, 2, "PCI "); + smp_write_bus(mc, 3, "PCI "); + smp_write_bus(mc, 4, "PCI "); + smp_write_bus(mc, 5, "ISA "); +/*I/O APICs: APIC ID Version State Address*/ + smp_write_ioapic(mc, 8, 0x20, 0xfec00000); + { + struct pci_dev *dev; + uint32_t base; + dev = dev_find_slot(1, PCI_DEVFN(0x1e,0)); + if (dev) { + base = pci_read_config32(dev, PCI_BASE_ADDRESS_0); + base &= PCI_BASE_ADDRESS_MEM_MASK; + smp_write_ioapic(mc, 9, 0x20, base); + } + dev = dev_find_slot(1, PCI_DEVFN(0x1c,0)); + if (dev) { + base = pci_read_config32(dev, PCI_BASE_ADDRESS_0); + base &= PCI_BASE_ADDRESS_MEM_MASK; + smp_write_ioapic(mc, 0xa, 0x20, base); + } + } +/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# +*/ + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x0, 0x8, 0x0); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x1, 0x8, 0x1); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x0, 0x8, 0x2); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x3, 0x8, 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x4, 0x8, 0x4); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x6, 0x8, 0x6); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x8, 0x8, 0x8); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0x9, 0x8, 0x9); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0xc, 0x8, 0xc); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0xd, 0x8, 0xd); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0xe, 0x8, 0xe); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x5, 0xf, 0x8, 0xf); +//USB + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x7c, 0x8, 0x12); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x7d, 0x8, 0x11); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x74, 0x8, 0x10); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x75, 0x8, 0x13); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x77, 0x8, 0x17); + +//onboard ati + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, 0x8, 0x8, 0x12); + +//onboard intel 82551 10/100 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, 0x4, 0x8, 0x11); + +// onboard Intel 82547 1000 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x4, 0xa, 0x0); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x5, 0xa, 0x1); + +//Slot 4 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|0, 0x8, 0x12); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|1, 0x8, 0x13); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|2, 0x8, 0x10); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x3<<2)|3, 0x8, 0x11); +//Slot 3 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|0, 0x8, 0x13); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|1, 0x8, 0x10); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|2, 0x8, 0x11); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x4, (0x4<<2)|3, 0x8, 0x12); +//Slot 1 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|0, 0x9, 0x0); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|1, 0x9, 0x1); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|2, 0x9, 0x2); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x3<<2)|3, 0x9, 0x3); +//Slot 2 + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|0, 0x9, 0x4); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|1, 0x9, 0x5); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|2, 0x9, 0x6); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, (0x6<<2)|3, 0x9, 0x7); + +/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/ + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x0, 0x0, MP_APIC_ALL, 0x0); + smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x0, 0x0, MP_APIC_ALL, 0x1); +/* +MP Config Extended Table Entries: + +-- +System Address Space + bus ID: 0 address type: I/O address + address base: 0x9000 + address range: 0x6000 +-- +System Address Space + bus ID: 0 address type: I/O address + address base: 0x0 + address range: 0x100 +-- +System Address Space + bus ID: 0 address type: memory address + address base: 0xa0000 + address range: 0x20000 +-- +System Address Space + bus ID: 0 address type: memory address + address base: 0xfc700000 + address range: 0x2500000 +-- +System Address Space + bus ID: 0 address type: prefetch address + address base: 0xff600000 + address range: 0x500000 +-- +Bus Heirarchy + bus ID: 5 bus info: 0x01 parent bus ID: 0-- +Compatibility Bus Address + bus ID: 0 address modifier: add + predefined range: 0x00000000-- +Compatibility Bus Address + bus ID: 0 address modifier: add + predefined range: 0x00000001 // There is no extension information... +*/ + /* Compute the checksums */ + mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length); + mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length); + printk_debug("Wrote the mp table end at: %p - %p\n", + mc, smp_next_mpe_entry(mc)); + return smp_next_mpe_entry(mc); +} + +unsigned long write_smp_table(unsigned long addr, unsigned long *processor_map) +{ + void *v; + v = smp_write_floating_table(addr); + return (unsigned long)smp_write_config_table(v, processor_map); +} diff --git a/src/northbridge/intel/e7501/Config.lb b/src/northbridge/intel/e7501/Config.lb new file mode 100644 index 0000000000..f101a921fd --- /dev/null +++ b/src/northbridge/intel/e7501/Config.lb @@ -0,0 +1,4 @@ +config chip.h +object northbridge.o +#driver misc_control.o + diff --git a/src/northbridge/intel/e7501/chip.h b/src/northbridge/intel/e7501/chip.h new file mode 100644 index 0000000000..4fa6df49b3 --- /dev/null +++ b/src/northbridge/intel/e7501/chip.h @@ -0,0 +1,5 @@ +struct northbridge_intel_e7501_config +{ +}; + +extern struct chip_control northbridge_intel_e7501_control; diff --git a/src/northbridge/intel/e7501/debug.c b/src/northbridge/intel/e7501/debug.c new file mode 100644 index 0000000000..67670f9844 --- /dev/null +++ b/src/northbridge/intel/e7501/debug.c @@ -0,0 +1,164 @@ +/* + * generic K8 debug code, used by mainboard specific auto.c + * + */ +#if 1 +static void print_debug_pci_dev(unsigned dev) +{ + print_debug("PCI: "); + print_debug_hex8((dev >> 16) & 0xff); + print_debug_char(':'); + print_debug_hex8((dev >> 11) & 0x1f); + print_debug_char('.'); + print_debug_hex8((dev >> 8) & 7); +} + +static void print_pci_devices(void) +{ + device_t dev; + for(dev = PCI_DEV(0, 0, 0); + dev <= PCI_DEV(0, 0x1f, 0x7); + dev += PCI_DEV(0,0,1)) { + uint32_t id; + id = pci_read_config32(dev, PCI_VENDOR_ID); + if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) || + (((id >> 16) & 0xffff) == 0xffff) || + (((id >> 16) & 0xffff) == 0x0000)) { + continue; + } + print_debug_pci_dev(dev); + print_debug("\r\n"); + } +} + +static void dump_pci_device(unsigned dev) +{ + int i; + print_debug_pci_dev(dev); + print_debug("\r\n"); + + for(i = 0; i <= 255; i++) { + unsigned char val; + if ((i & 0x0f) == 0) { + print_debug_hex8(i); + print_debug_char(':'); + } + val = pci_read_config8(dev, i); + print_debug_char(' '); + print_debug_hex8(val); + if ((i & 0x0f) == 0x0f) { + print_debug("\r\n"); + } + } +} + +static void dump_pci_devices(void) +{ + device_t dev; + for(dev = PCI_DEV(0, 0, 0); + dev <= PCI_DEV(0, 0x1f, 0x7); + dev += PCI_DEV(0,0,1)) { + uint32_t id; + id = pci_read_config32(dev, PCI_VENDOR_ID); + if (((id & 0xffff) == 0x0000) || ((id & 0xffff) == 0xffff) || + (((id >> 16) & 0xffff) == 0xffff) || + (((id >> 16) & 0xffff) == 0x0000)) { + continue; + } + dump_pci_device(dev); + } +} + +static void dump_spd_registers(const struct mem_controller *ctrl) +{ + int i; + print_debug("\r\n"); + for(i = 0; i < 4; i++) { + unsigned device; + device = ctrl->channel0[i]; + if (device) { + int j; + print_debug("dimm: "); + print_debug_hex8(i); + print_debug(".0: "); + print_debug_hex8(device); + for(j = 0; j < 256; j++) { + int status; + unsigned char byte; + if ((j & 0xf) == 0) { + print_debug("\r\n"); + print_debug_hex8(j); + print_debug(": "); + } + status = smbus_read_byte(device, j); + if (status < 0) { + print_debug("bad device\r\n"); + break; + } + byte = status & 0xff; + print_debug_hex8(byte); + print_debug_char(' '); + } + print_debug("\r\n"); + } +#if 0 + device = ctrl->channel1[i]; + if (device) { + int j; + print_debug("dimm: "); + print_debug_hex8(i); + print_debug(".1: "); + print_debug_hex8(device); + for(j = 0; j < 256; j++) { + int status; + unsigned char byte; + if ((j & 0xf) == 0) { + print_debug("\r\n"); + print_debug_hex8(j); + print_debug(": "); + } + status = smbus_read_byte(device, j); + if (status < 0) { + print_debug("bad device\r\n"); + break; + } + byte = status & 0xff; + print_debug_hex8(byte); + print_debug_char(' '); + } + print_debug("\r\n"); + } +#endif + } +} +static void dump_smbus_registers(void) +{ + int i; + print_debug("\r\n"); + for(i = 1; i < 0x80; i++) { + unsigned device; + device = i; + int j; + print_debug("smbus: "); + print_debug_hex8(device); + for(j = 0; j < 256; j++) { + int status; + unsigned char byte; + if ((j & 0xf) == 0) { + print_debug("\r\n"); + print_debug_hex8(j); + print_debug(": "); + } + status = smbus_read_byte(device, j); + if (status < 0) { + print_debug("bad device\r\n"); + break; + } + byte = status & 0xff; + print_debug_hex8(byte); + print_debug_char(' '); + } + print_debug("\r\n"); + } +} +#endif diff --git a/src/northbridge/intel/e7501/e7501.h b/src/northbridge/intel/e7501/e7501.h new file mode 100644 index 0000000000..e69de29bb2 diff --git a/src/northbridge/intel/e7501/northbridge.c b/src/northbridge/intel/e7501/northbridge.c new file mode 100644 index 0000000000..452166ba28 --- /dev/null +++ b/src/northbridge/intel/e7501/northbridge.c @@ -0,0 +1,151 @@ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "chip.h" + +struct mem_range *sizeram(void) +{ + static struct mem_range mem[4]; + /* the units of tolm are 64 KB */ + /* the units of drb16 are 64 MB */ + uint16_t tolm, remapbase, remaplimit, drb16; + uint16_t tolm_r, remapbase_r, remaplimit_r; + uint8_t drb; + int remap_high; + device_t dev; + + dev = dev_find_slot(0, 0); // d0f0 + if (!dev) { + printk_err("Cannot find PCI: 0:0\n"); + return 0; + } + + /* Calculate and report the top of low memory and + * any remapping. + */ + /* Test if the remap memory high option is set */ + remap_high = 0; +// if(get_option(&remap_high, "remap_memory_high")){ +// remap_high = 0; +// } + printk_debug("remap_high is %d\n", remap_high); + /* get out the value of the highest DRB. This tells the end of + * physical memory. The units are ticks of 64 MB i.e. 1 means + * 64 MB. + */ + drb = pci_read_config8(dev, 0x67); + drb16 = (uint16_t)drb; + if(remap_high && (drb16 > 0x08)) { + /* We only come here if we have at least 512MB of memory, + * so it is safe to hard code tolm. + * 0x2000 means 512MB + */ + + tolm = 0x2000; + /* i.e 0x40 * 0x40 is 0x1000 which is 4 GB */ + if(drb16 > 0x0040) { + /* There is more than 4GB of memory put + * the remap window at the end of ram. + */ + remapbase = drb16; + remaplimit = remapbase + 0x38; + } + else { + remapbase = 0x0040; + remaplimit = remapbase + (drb16-8); + } + } + else { + tolm = (uint16_t)((dev_root.resource[1].base >> 16)&0x0f800); + if((tolm>>8) >= (drb16<<2)) { + tolm = (drb16<<10); + remapbase = 0x3ff; + remaplimit = 0; + } + else { + remapbase = drb16; + remaplimit = remapbase + ((0x0040-(tolm>>10))-1); + } + } + /* Write the ram configruation registers, + * preserving the reserved bits. + */ + tolm_r = pci_read_config16(dev, 0xc4); + tolm |= (tolm_r & 0x7ff); + pci_write_config16(dev, 0xc4, tolm); + remapbase_r = pci_read_config16(dev, 0xc6); + remapbase |= (remapbase_r & 0xfc00); + pci_write_config16(dev, 0xc6, remapbase); + remaplimit_r = pci_read_config16(dev, 0xc8); + remaplimit |= (remaplimit_r & 0xfc00); + pci_write_config16(dev, 0xc8, remaplimit); + +#if 0 + printk_debug("mem info tolm = %x, drb = %x, pci_memory_base = %x, remap = %x-%x\n",tolm,drb,pci_memory_base,remapbase,remaplimit); +#endif + + mem[0].basek = 0; + mem[0].sizek = 640; + mem[1].basek = 768; + /* Convert size in 64K bytes to size in K bytes */ + mem[1].sizek = (tolm << 6) - mem[1].basek; + mem[2].basek = 0; + mem[2].sizek = 0; + if ((drb << 16) > (tolm << 6)) { + /* We don't need to consider the remap window + * here because we put it immediately after the + * rest of ram. + * All we must do is calculate the amount + * of unused memory and report it at 4GB. + */ + mem[2].basek = 4096*1024; + mem[2].sizek = (drb << 16) - (tolm << 6); + } + mem[3].basek = 0; + mem[3].sizek = 0; + + return mem; +} +static void enumerate(struct chip *chip) +{ + extern struct device_operations default_pci_ops_bus; + chip_enumerate(chip); + chip->dev->ops = &default_pci_ops_bus; +} +#if 0 +static void northbridge_init(struct chip *chip, enum chip_pass pass) +{ + + struct northbridge_intel_e7501_config *conf = + (struct northbridge_intel_e7501_config *)chip->chip_info; + + switch (pass) { + case CONF_PASS_PRE_PCI: + break; + + case CONF_PASS_POST_PCI: + break; + + case CONF_PASS_PRE_BOOT: + break; + + default: + /* nothing yet */ + break; + } +} +#endif + +struct chip_control northbridge_intel_e7501_control = { + .enumerate = enumerate, +// .enable = northbridge_init, + .name = "intel E7501 Northbridge", +}; diff --git a/src/northbridge/intel/e7501/raminit.c b/src/northbridge/intel/e7501/raminit.c new file mode 100644 index 0000000000..09743ba5fd --- /dev/null +++ b/src/northbridge/intel/e7501/raminit.c @@ -0,0 +1,2099 @@ + +/* This was originally for the e7500, modified for e7501 + * The primary differences are that 7501 apparently can + * support single channel RAM (i haven't tested), + * CAS1.5 is no longer supported, The ECC scrubber + * now supports a mode to zero RAM and init ECC in one step + * and the undocumented registers at 0x80 require new + * (undocumented) values determined by guesswork and + * comparison w/ OEM BIOS values. + * Steven James 02/06/2003 + */ + +/* converted to C 6/2004 yhlu */ + +#define DEBUG_RAM_CONFIG 0 + +#define dumpnorth() dump_pci_device(PCI_DEV(0, 0, 0)) + +/* DDR DIMM Mode register Definitions */ + +#define BURST_2 (1<<0) +#define BURST_4 (2<<0) +#define BURST_8 (3<<0) + +#define BURST_SEQUENTIAL (0<<3) +#define BURST_INTERLEAVED (1<<3) + +#define CAS_2_0 (0x2<<4) +#define CAS_3_0 (0x3<<4) +#define CAS_1_5 (0x5<<4) +#define CAS_2_5 (0x6<<4) + +#define MODE_NORM (0 << 7) +#define MODE_DLL_RESET (2 << 7) +#define MODE_TEST (1 << 7) + +#define BURST_LENGTH BURST_4 +#define BURST_TYPE BURST_INTERLEAVED +#define CAS_LATENCY CAS_2_0 +//#define CAS_LATENCY CAS_2_5 +//#define CAS_LATENCY CAS_1_5 + +#define MRS_VALUE (MODE_NORM | CAS_LATENCY | BURST_TYPE | BURST_LENGTH) +#define EMRS_VALUE 0x000 + +#define MD_SHIFT 4 + +#define RAM_COMMAND_NONE 0x0 +#define RAM_COMMAND_NOP 0x1 +#define RAM_COMMAND_PRECHARGE 0x2 +#define RAM_COMMAND_MRS 0x3 +#define RAM_COMMAND_EMRS 0x4 +#define RAM_COMMAND_CBR 0x6 +#define RAM_COMMAND_NORMAL 0x7 + + +static inline void do_ram_command (const struct mem_controller *ctrl, uint32_t value) { + uint32_t dword; + uint8_t byte; + int i; + uint32_t result; +#if DEBUG_RAM_CONFIG >= 2 + print_debug("P:"); + print_debug_hex8(value); + print_debug("\r\n"); +#endif + /* %ecx - initial address to read from */ + /* Compute the offset */ + dword = value >> 16; + for(i=0;i<8;i++) { + /* Set the ram command */ + byte = pci_read_config8(ctrl->d0, 0x7c); + byte &= 0x8f; + byte |= (uint8_t)(value & 0xff); + pci_write_config8(ctrl->d0, 0x7c, byte); + + /* Assert the command to the memory */ +#if DEBUG_RAM_CONFIG >= 2 + print_debug("R:"); + print_debug_hex32(dword); + print_debug("\r\n"); +#endif + + result = read32(dword); + + /* Go to the next base address */ + dword += 0x04000000; + + } + + /* The command has been sent to all dimms so get out */ +} + + +static inline void RAM_CMD(const struct mem_controller *ctrl, uint32_t command, uint32_t offset) { + uint32_t value = ((offset) << (MD_SHIFT + 16))|((command << 4) & 0x70) ; + do_ram_command(ctrl, value); +} + +#define RAM_NOP(ctrl) RAM_CMD(ctrl, RAM_COMMAND_NOP, 0) +#define RAM_PRECHARGE(ctrl) RAM_CMD(ctrl, RAM_COMMAND_PRECHARGE, 0) +#define RAM_CBR(ctrl) RAM_CMD(ctrl, RAM_COMMAND_CBR, 0) +#define RAM_EMRS(ctrl) RAM_CMD(ctrl, RAM_COMMAND_EMRS, EMRS_VALUE) + +static const uint8_t ram_cas_latency[] = { + CAS_2_5, CAS_2_0, CAS_1_5, CAS_2_5 + }; + +static inline void ram_mrs(const struct mem_controller *ctrl, uint32_t value){ + /* Read the cas latency setting */ + uint8_t byte; + uint32_t dword; + byte = pci_read_config8(ctrl->d0, 0x78); + /* Transform it into the form expected by SDRAM */ + dword = ram_cas_latency[(byte>>4) & 3]; + + value |= (dword<<(16+MD_SHIFT)); + + value |= (MODE_NORM | BURST_TYPE | BURST_LENGTH) << (16+MD_SHIFT); + + do_ram_command(ctrl, value); +} + +#define RAM_MRS(ctrl, dll_reset) ram_mrs( ctrl, (dll_reset << (8+MD_SHIFT+ 16)) | ((RAM_COMMAND_MRS <<4)& 0x70) ) + +static void RAM_NORMAL(const struct mem_controller *ctrl) { + uint8_t byte; + byte = pci_read_config8(ctrl->d0, 0x7c); + byte &= 0x8f; + byte |= (RAM_COMMAND_NORMAL << 4); + pci_write_config8(ctrl->d0, 0x7c, byte); +} + +static void RAM_RESET_DDR_PTR(const struct mem_controller *ctrl) { + uint8_t byte; + byte = pci_read_config8(ctrl->d0, 0x88); + byte |= (1 << 4 ); + pci_write_config8(ctrl->d0, 0x88, byte); + byte = pci_read_config8(ctrl->d0, 0x88); + byte &= ~(1 << 4); + pci_write_config8(ctrl->d0, 0x88, byte); +} + +static void ENABLE_REFRESH(const struct mem_controller *ctrl) +{ + uint32_t dword; + dword = pci_read_config32(ctrl->d0, 0x7c); + dword |= (1 << 29); + pci_write_config32(ctrl->d0, 0x7c, dword); +} + + /* + * Table: constant_register_values + */ +static const long register_values[] = { + /* SVID - Subsystem Vendor Identification Register + * 0x2c - 0x2d + * [15:00] Subsytem Vendor ID (Indicates system board vendor) + */ + /* SID - Subsystem Identification Register + * 0x2e - 0x2f + * [15:00] Subsystem ID + */ + 0x2c, 0, (0x15d9 << 0) | (0x3580 << 16), + + /* Undocumented + * 0x80 - 0x80 + * This register has something to do with CAS latencies, + * possibily this is the real chipset control. + * At 0x00 CAS latency 1.5 works. + * At 0x06 CAS latency 2.5 works. + * At 0x01 CAS latency 2.0 works. + */ + /* This is still undocumented in e7501, but with different values + * CAS 2.0 values taken from Intel BIOS settings, others are a guess + * and may be terribly wrong. Old values preserved as comments until I + * figure this out for sure. + * e7501 docs claim that CAS1.5 is unsupported, so it may or may not + * work at all. + * Steven James 02/06/2003 + */ +#if CAS_LATENCY == CAS_2_5 +// 0x80, 0xfffffe00, 0x06 /* Intel E7500 recommended */ + 0x80, 0xfffff000, 0x0662, /* from Factory Bios */ +#elif CAS_LATENCY == CAS_2_0 +// 0x80, 0xfffffe00, 0x0d /* values for register 0x80 */ + 0x80, 0xfffff000, 0x0bb1, /* values for register 0x80 */ +#endif + + /* Enable periodic memory recalibration */ + 0x88, 0xffffff00, 0x80, + + /* FDHC - Fixed DRAM Hole Control + * 0x58 + * [7:7] Hole_Enable + * 0 == No memory Hole + * 1 == Memory Hole from 15MB to 16MB + * [6:0] Reserved + * + * PAM - Programmable Attribute Map + * 0x59 [1:0] Reserved + * 0x59 [5:4] 0xF0000 - 0xFFFFF + * 0x5A [1:0] 0xC0000 - 0xC3FFF + * 0x5A [5:4] 0xC4000 - 0xC7FFF + * 0x5B [1:0] 0xC8000 - 0xCBFFF + * 0x5B [5:4] 0xCC000 - 0xCFFFF + * 0x5C [1:0] 0xD0000 - 0xD3FFF + * 0x5C [5:4] 0xD4000 - 0xD7FFF + * 0x5D [1:0] 0xD8000 - 0xDBFFF + * 0x5D [5:4] 0xDC000 - 0xDFFFF + * 0x5E [1:0] 0xE0000 - 0xE3FFF + * 0x5E [5:4] 0xE4000 - 0xE7FFF + * 0x5F [1:0] 0xE8000 - 0xEBFFF + * 0x5F [5:4] 0xEC000 - 0xEFFFF + * 00 == DRAM Disabled (All Access go to memory mapped I/O space) + * 01 == Read Only (Reads to DRAM, Writes to memory mapped I/O space) + * 10 == Write Only (Writes to DRAM, Reads to memory mapped I/O space) + * 11 == Normal (All Access go to DRAM) + */ + 0x58, 0xcccccf7f, (0x00 << 0) | (0x30 << 8) | (0x33 << 16) | (0x33 << 24), + 0x5C, 0xcccccccc, (0x33 << 0) | (0x33 << 8) | (0x33 << 16) | (0x33 << 24), + + /* DRB - DRAM Row Boundary Registers + * 0x60 - 0x6F + * An array of 8 byte registers, which hold the ending + * memory address assigned to each pair of DIMMS, in 64MB + * granularity. + */ + /* Conservatively say each row has 64MB of ram, we will fix this up later */ + 0x60, 0x00000000, (0x01 << 0) | (0x02 << 8) | (0x03 << 16) | (0x04 << 24), + 0x64, 0x00000000, (0x05 << 0) | (0x06 << 8) | (0x07 << 16) | (0x08 << 24), + 0x68, 0xffffffff, 0, + 0x6C, 0xffffffff, 0, + + /* DRA - DRAM Row Attribute Register + * 0x70 Row 0,1 + * 0x71 Row 2,3 + * 0x72 Row 4,5 + * 0x73 Row 6,7 + * [7:7] Device width for Odd numbered rows + * 0 == 8 bits wide x8 + * 1 == 4 bits wide x4 + * [6:4] Row Attributes for Odd numbered rows + * 010 == 8KB + * 011 == 16KB + * 100 == 32KB + * 101 == 64KB + * Others == Reserved + * [3:3] Device width for Even numbered rows + * 0 == 8 bits wide x8 + * 1 == 4 bits wide x4 + * [2:0] Row Attributes for Even numbered rows + * 010 == 8KB + * 011 == 16KB + * 100 == 32KB + * 101 == 64KB (This page size appears broken) + * Others == Reserved + */ + 0x70, 0x00000000, + (((0<<3)|(0<<0))<< 0) | + (((0<<3)|(0<<0))<< 4) | + (((0<<3)|(0<<0))<< 8) | + (((0<<3)|(0<<0))<<12) | + (((0<<3)|(0<<0))<<16) | + (((0<<3)|(0<<0))<<20) | + (((0<<3)|(0<<0))<<24) | + (((0<<3)|(0<<0))<<28), + 0x74, 0xffffffff, 0, + + /* DRT - DRAM Time Register + * 0x78 + * [31:30] Reserved + * [29:29] Back to Back Write-Read Turn Around + * 0 == 3 clocks between WR-RD commands + * 1 == 2 clocks between WR-RD commands + * [28:28] Back to Back Read-Write Turn Around + * 0 == 5 clocks between RD-WR commands + * 1 == 4 clocks between RD-WR commands + * [27:27] Back to Back Read Turn Around + * 0 == 4 clocks between RD commands + * 1 == 3 clocks between RD commands + * [26:24] Read Delay (tRD) + * 000 == 7 clocks + * 001 == 6 clocks + * 010 == 5 clocks + * Others == Reserved + * [23:19] Reserved + * [18:16] DRAM idle timer + * 000 == infinite + * 011 == 16 dram clocks + * 001 == Datasheet says reserved, but Intel BIOS sets it + * [15:11] Reserved + * [10:09] Active to Precharge (tRAS) + * 00 == 7 clocks + * 01 == 6 clocks + * 10 == 5 clocks + * 11 == Reserved + * [08:06] Reserved + * [05:04] Cas Latency (tCL) + * 00 == 2.5 Clocks + * 01 == 2.0 Clocks + * 10 == 1.5 Clocks + * 11 == Reserved + * [03:03] Write Ras# to Cas# Delay (tRCD) + * 0 == 3 DRAM Clocks + * 1 == 2 DRAM Clocks + * [02:01] Read RAS# to CAS# Delay (tRCD) + * 00 == reserved + * 01 == reserved + * 10 == 3 DRAM Clocks + * 11 == 2 DRAM Clocks + * [00:00] DRAM RAS# to Precharge (tRP) + * 0 == 3 DRAM Clocks + * 1 == 2 DRAM Clocks + */ +#define DRT_CAS_2_5 (0<<4) +#define DRT_CAS_2_0 (1<<4) +#define DRT_CAS_1_5 (2<<4) +#define DRT_CAS_MASK (3<<4) + +#if CAS_LATENCY == CAS_2_5 +#define DRT_CL DRT_CAS_2_5 +#elif CAS_LATENCY == CAS_2_0 +#define DRT_CL DRT_CAS_2_0 +#elif CAS_LATENCY == CAS_1_5 +#define DRT_CL DRT_CAS_1_5 +#endif + + /* Most aggressive settings possible */ +// 0x78, 0xc0fff8c4, (1<<29)|(1<<28)|(1<<27)|(2<<24)|(2<<9)|DRT_CL|(1<<3)|(1<<1)|(1<<0), +// 0x78, 0xc0f8f8c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|DRT_CL|(1<<3)|(3<<1)|(1<<0), + 0x78, 0xc0f8f9c0, (1<<29)|(1<<28)|(1<<27)|(1<<24)|(1<<16)|(2<<9)|DRT_CL|(1<<3)|(3<<1)|(1<<0), + + /* FIXME why was I attempting to set a reserved bit? */ + /* 0x0100040f */ + + /* DRC - DRAM Contoller Mode Register + * 0x7c + * [31:30] Reserved + * [29:29] Initialization Complete + * 0 == Not Complete + * 1 == Complete + * [28:23] Reserved + * [22:22] Channels + * 0 == Single channel + * 1 == Dual Channel + * [21:20] DRAM Data Integrity Mode + * 00 == Disabled, no ECC + * 01 == Reserved + * 10 == Error checking, using chip-kill, with correction + * 11 == Reserved + * [19:18] Reserved + * Must equal 01 + * [17:17] (Intel Undocumented) should always be set to 1 + * [16:16] Command Per Clock - Address/Control Assertion Rule (CPC) + * 0 == 2n Rule + * 1 == 1n rule + * [15:11] Reserved + * [10:08] Refresh mode select + * 000 == Refresh disabled + * 001 == Refresh interval 15.6 usec + * 010 == Refresh interval 7.8 usec + * 011 == Refresh interval 64 usec + * 111 == Refresh every 64 clocks (fast refresh) + * [07:07] Reserved + * [06:04] Mode Select (SMS) + * 000 == Self Refresh Mode + * 001 == NOP Command + * 010 == All Banks Precharge + * 011 == Mode Register Set + * 100 == Extended Mode Register Set + * 101 == Reserved + * 110 == CBR Refresh + * 111 == Normal Operation + * [03:00] Reserved + */ +// .long 0x7c, 0xffcefcff, (1<<22)|(2 << 20)|(1 << 16)| (0 << 8), +// .long 0x7c, 0xff8cfcff, (1<<22)|(2 << 20)|(1 << 17)|(1 << 16)| (0 << 8), +// .long 0x7c, 0xff80fcff, (1<<22)|(2 << 20)|(1 << 18)|(1 << 17)|(1 << 16)| (0 << 8), + 0x7c, 0xff82fcff, (1<<22)|(2 << 20)|(1 << 18)|(1 << 16)| (0 << 8), + + + /* Another Intel undocumented register */ + 0x88, 0x080007ff, (1<<31)|(1 << 30)|(1<<28)|(0 << 26)|(0x10 << 21)|(10 << 16)|(0x13 << 11), + + /* CLOCK_DIS - CK/CK# Disable Register + * 0x8C + * [7:4] Reserved + * [3:3] CK3 + * 0 == Enable + * 1 == Disable + * [2:2] CK2 + * 0 == Enable + * 1 == Disable + * [1:1] CK1 + * 0 == Enable + * 1 == Disable + * [0:0] CK0 + * 0 == Enable + * 1 == Disable + */ + 0x8C, 0xfffffff0, 0xf, + + /* TOLM - Top of Low Memory Register + * 0xC4 - 0xC5 + * [15:11] Top of low memory (TOLM) + * The address below 4GB that should be treated as RAM, + * on a 128MB granularity. + * [10:00] Reserved + */ + /* REMAPBASE - Remap Base Address Regsiter + * 0xC6 - 0xC7 + * [15:10] Reserved + * [09:00] Remap Base Address [35:26] 64M aligned + * Bits [25:0] are assumed to be 0. + */ + 0xc4, 0xfc0007ff, (0x2000 << 0) | (0x3ff << 16), + /* REMAPLIMIT - Remap Limit Address Register + * 0xC8 - 0xC9 + * [15:10] Reserved + * [09:00] Remap Limit Address [35:26] 64M aligned + * When remaplimit < remapbase this register is disabled. + */ + 0xc8, 0xfffffc00, 0, + + /* DVNP - Device Not Present Register + * 0xE0 - 0xE1 + * [15:05] Reserved + * [04:04] Device 4 Function 1 Present + * 0 == Present + * 1 == Absent + * [03:03] Device 3 Function 1 Present + * 0 == Present + * 1 == Absent + * [02:02] Device 2 Function 1 Present + * 0 == Present + * 1 == Absent + * [01:01] Reserved + * [00:00] Device 0 Function 1 Present + * 0 == Present + * 1 == Absent + */ + 0xe0, 0xffffffe2, (1<<4)|(1<<3)|(1<<2)|(0<<0), + 0xd8, 0xffff9fff, 0x00000000, + 0xf4, 0x3f8ffffd, 0x40300002, + 0x1050, 0xffffffcf, 0x00000030, +}; + + + /* + * Routine: ram_set_registers + * Arguments: none + * Results: none + * Trashed: %eax, %ebx, %ecx, %edx, %esi, %eflags + * Effects: Do basic ram setup that does not depend on serial + * presence detect information. + * This sets PCI configuration registers to known good + * values based on the table: + * constant_register_values + * Which are a triple of configuration regiser, mask, and value. + * + */ +/* from 1M or 512K */ +#define RCOMP_MMIO 0x100000 + + /* DDR RECOMP table */ + +static const long ddr_rcomp_1[] = { + 0x44332211, 0xc9776655, 0xffffffff, 0xffffffff, + 0x22111111, 0x55444332, 0xfffca876, 0xffffffff, +}; +static const long ddr_rcomp_2[] = { + 0x00000000, 0x76543210, 0xffffeca8, 0xffffffff, + 0x21000000, 0xa8765432, 0xffffffec, 0xffffffff, +}; +static const long ddr_rcomp_3[] = { + 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, + 0x88888888, 0x88888888, 0x88888888, 0x88888888, +}; + +#define rcomp_init_str "Setting RCOMP registers.\r\n" + +static void write_8dwords(uint32_t src_addr, uint32_t dst_addr) { + int i; + uint32_t dword; + for(i=0;i<8;i++) { + dword = read32(src_addr); + write32(dst_addr, dword); + src_addr+=4; + dst_addr+=4; + + } +} + +//#define SLOW_DOWN_IO inb(0x80); +#define SLOW_DOWN_IO udelay(40); + +static void ram_set_rcomp_regs(const struct mem_controller *ctrl) { + uint32_t dword; +#if DEBUG_RAM_CONFIG + print_debug(rcomp_init_str); +#endif + + /*enable access to the rcomp bar */ + dword = pci_read_config32(ctrl->d0, 0x0f4); + dword &= ~(1<<31); + dword |=((1<<30)|1<<22); + pci_write_config32(ctrl->d0, 0x0f4, dword); + + + /* Set the MMIO address to 512K */ + pci_write_config32(ctrl->d0, 0x14, RCOMP_MMIO); + + dword = read32(RCOMP_MMIO + 0x20); + dword |= (1<<9); + write32(RCOMP_MMIO + 0x20, dword); + + + /* Begin to write the RCOMP registers */ + + write8(RCOMP_MMIO + 0x2c, 0xff); + write32(RCOMP_MMIO + 0x30, 0x01040444); + write8(RCOMP_MMIO + 0x34, 0x04); + write32(RCOMP_MMIO + 0x40, 0); + write16(RCOMP_MMIO + 0x44, 0); + write16(RCOMP_MMIO + 0x48, 0); + write16(RCOMP_MMIO + 0x50, 0); + write_8dwords((uint32_t)ddr_rcomp_1, RCOMP_MMIO + 0x60); + write_8dwords((uint32_t)ddr_rcomp_2, RCOMP_MMIO + 0x80); + write_8dwords((uint32_t)ddr_rcomp_2, RCOMP_MMIO + 0xa0); + write_8dwords((uint32_t)ddr_rcomp_2, RCOMP_MMIO + 0x140); + write_8dwords((uint32_t)ddr_rcomp_2, RCOMP_MMIO + 0x1c0); + write_8dwords((uint32_t)ddr_rcomp_3, RCOMP_MMIO + 0x180); + +#if 0 /* Print the RCOMP registers */ + movl $RCOMP_MMIO, %ecx +1: movl %ecx, %eax + andb $0x0f, %al + jnz 2f + CONSOLE_INFO_TX_CHAR($'\r') + CONSOLE_INFO_TX_CHAR($'\n') + CONSOLE_INFO_TX_HEX32(%ecx) + CONSOLE_INFO_TX_CHAR($' ') + CONSOLE_INFO_TX_CHAR($'-') + CONSOLE_INFO_TX_CHAR($' ') +2: movl (%ecx), %eax + CONSOLE_INFO_TX_HEX32(%eax) + CONSOLE_INFO_TX_CHAR($' ') + addl $4, %ecx + cmpl $(RCOMP_MMIO + 0x1e0), %ecx + jnz 1b + CONSOLE_INFO_TX_CHAR($'\r') + CONSOLE_INFO_TX_CHAR($'\n') +#endif + + dword = read32(RCOMP_MMIO + 0x20); + dword &= ~(3); + dword |= 1; + write32(RCOMP_MMIO + 0x20, dword); + + /* Wait 40 usec */ + SLOW_DOWN_IO; + + /* unblock updates */ + dword = read32(RCOMP_MMIO + 0x20); + dword &= ~(1<<9); + write32(RCOMP_MMIO+0x20, dword); + dword |= (1<<8); + write32(RCOMP_MMIO+0x20, dword); + dword &= ~(1<<8); + write32(RCOMP_MMIO+0x20, dword); + + /* Wait 40 usec */ + SLOW_DOWN_IO; + + /*disable access to the rcomp bar */ + dword = pci_read_config32(ctrl->d0, 0x0f4); + dword &= ~(1<<22); + pci_write_config32(ctrl->d0, 0x0f4, dword); + +} + +static void ram_set_d0f0_regs(const struct mem_controller *ctrl) { +#if DEBUG_RAM_CONFIG + dumpnorth(); +#endif + int i; + int max; + max = sizeof(register_values)/sizeof(register_values[0]); + for(i = 0; i < max; i += 3) { + uint32_t reg; +#if DEBUG_RAM_CONFIG + print_debug_hex32(register_values[i]); + print_debug(" <-"); + print_debug_hex32(register_values[i+2]); + print_debug("\r\n"); +#endif + reg = pci_read_config32(ctrl->d0,register_values[i]); + reg &= register_values[i+1]; + reg |= register_values[i+2] & ~(register_values[i+1]); + pci_write_config32(ctrl->d0,register_values[i], reg); + + + } +#if DEBUG_RAM_CONFIG + dumpnorth(); +#endif +} +static void sdram_set_registers(const struct mem_controller *ctrl){ + ram_set_rcomp_regs(ctrl); + ram_set_d0f0_regs(ctrl); +} + + + /* + * Routine: sdram_spd_get_page_size + * Arguments: %bl SMBUS_MEM_DEVICE + * Results: + * %edi log base 2 page size of DIMM side 1 in bits + * %esi log base 2 page size of DIMM side 2 in bits + * + * Preserved: %ebx (except %bh), %ebp + * + * Trashed: %eax, %bh, %ecx, %edx, %esp, %eflags + * Used: %eax, %ebx, %ecx, %edx, %esi, %edi, %esp, %eflags + * + * Effects: Uses serial presence detect to set %edi & %esi + * to the page size of a dimm. + * Notes: + * %bl SMBUS_MEM_DEVICE + * %edi holds the page size for the first side of the DIMM. + * %esi holds the page size for the second side of the DIMM. + * memory size is represent as a power of 2. + * + * This routine may be worth moving into generic code somewhere. + */ +struct dimm_page_size { + unsigned long side1; + unsigned long side2; +}; + +static struct dimm_page_size sdram_spd_get_page_size(unsigned device) { + + uint32_t ecx; + int value; + struct dimm_page_size pgsz; + + pgsz.side1 = 0; + pgsz.side2 = 0; + + value = spd_read_byte(device, 4); /* columns */ + if(value < 0) goto hw_err; + pgsz.side1 = value & 0xf; + + /* Get the module data width and convert it to a power of two */ + value = spd_read_byte(device,7); /* (high byte) */ + if(value < 0) goto hw_err; + ecx = value & 0xff; + ecx <<= 8; + + value = spd_read_byte(device, 6); /* (low byte) */ + if(value < 0) goto hw_err; + ecx |= (value & 0xff); + + pgsz.side1 += log2(ecx); /* compute cheap log base 2 */ + + /* side two */ + value = spd_read_byte(device, 5); /* number of physical banks */ + if(value < 0) goto hw_err; + if(value==1) goto out; + if(value!=2) goto val_err; + + /* Start with the symmetrical case */ + pgsz.side2 = pgsz.side1; + value = spd_read_byte(device,4); /* columns */ + if(value < 0) goto hw_err; + if((value & 0xf0)==0 ) goto out; + pgsz.side2 -=value & 0xf; /* Subtract out columns on side 1 */ + pgsz.side2 +=(value>>4)& 0xf; /* Add in columns on side 2 */ + goto out; + + val_err: + die("Bad SPD value\r\n"); + /* If an hw_error occurs report that I have no memory */ +hw_err: + pgsz.side1 = 0; + pgsz.side2 = 0; +out: + return pgsz; +} + + + /* + * Routine: sdram_spd_get_width + * Arguments: %bl SMBUS_MEM_DEVICE + * Results: + * %edi width of SDRAM chips on DIMM side 1 in bits + * %esi width of SDRAM chips on DIMM side 2 in bits + * + * Preserved: %ebx (except %bh), %ebp + * + * Trashed: %eax, %bh, %ecx, %edx, %esp, %eflags + * Used: %eax, %ebx, %ecx, %edx, %esi, %edi, %esp, %eflags + * + * Effects: Uses serial presence detect to set %edi & %esi + * to the width of a dimm. + * Notes: + * %bl SMBUS_MEM_DEVICE + * %edi holds the width for the first side of the DIMM. + * %esi holds the width for the second side of the DIMM. + * memory size is represent as a power of 2. + * + * This routine may be worth moving into generic code somewhere. + */ +struct dimm_width { + unsigned side1; + unsigned side2; +}; + +static struct dimm_width sdram_spd_get_width(unsigned device) { + int value; + struct dimm_width wd; + uint32_t ecx; + + wd.side1 = 0; + wd.side2 = 0; + + value = spd_read_byte(device, 13); /* sdram width */ + if(value < 0 ) goto hw_err; + ecx = value; + + wd.side1 = value & 0x7f; + + /* side two */ + value = spd_read_byte(device, 5); /* number of physical banks */ + if(value < 0 ) goto hw_err; + if(value <=1 ) goto out; + + /* Start with the symmetrical case */ + wd.side2 = wd.side1; + + if((ecx & 0x80)==0) goto out; + + wd.side2 <<=1; +hw_err: + wd.side1 = 0; + wd.side2 = 0; + + out: + return wd; +} + + /* + * Routine: sdram_spd_get_dimm_size + * Arguments: %bl SMBUS_MEM_DEVICE + * Results: + * %edi log base 2 size of DIMM side 1 in bits + * %esi log base 2 size of DIMM side 2 in bits + * + * Preserved: %ebx (except %bh), %ebp + * + * Trashed: %eax, %bh, %ecx, %edx, %esp, %eflags + * Used: %eax, %ebx, %ecx, %edx, %esi, %edi, %esp, %eflags + * + * Effects: Uses serial presence detect to set %edi & %esi + * the size of a dimm. + * Notes: + * %bl SMBUS_MEM_DEVICE + * %edi holds the memory size for the first side of the DIMM. + * %esi holds the memory size for the second side of the DIMM. + * memory size is represent as a power of 2. + * + * This routine may be worth moving into generic code somewhere. + */ + +struct dimm_size { + unsigned long side1; + unsigned long side2; +}; + +static struct dimm_size spd_get_dimm_size(unsigned device) +{ + /* Calculate the log base 2 size of a DIMM in bits */ + struct dimm_size sz; + int value, low; + sz.side1 = 0; + sz.side2 = 0; + + /* Note it might be easier to use byte 31 here, it has the DIMM size as + * a multiple of 4MB. The way we do it now we can size both + * sides of an assymetric dimm. + */ + value = spd_read_byte(device, 3); /* rows */ + if (value < 0) goto hw_err; +// if ((value & 0xf) == 0) goto val_err; + sz.side1 += value & 0xf; + + value = spd_read_byte(device, 4); /* columns */ + if (value < 0) goto hw_err; +// if ((value & 0xf) == 0) goto val_err; + sz.side1 += value & 0xf; + + value = spd_read_byte(device, 17); /* banks */ + if (value < 0) goto hw_err; +// if ((value & 0xff) == 0) goto val_err; + value &=0xff; + sz.side1 += log2(value); + + /* Get the module data width and convert it to a power of two */ + value = spd_read_byte(device, 7); /* (high byte) */ + if (value < 0) goto hw_err; + value &= 0xff; + value <<= 8; + + low = spd_read_byte(device, 6); /* (low byte) */ + if (low < 0) goto hw_err; + value |= (low & 0xff); +// if ((value != 72) && (value != 64)) goto val_err; + sz.side1 += log2(value); + + /* side 2 */ + value = spd_read_byte(device, 5); /* number of physical banks */ + if (value < 0) goto hw_err; + if (value == 1) goto out; +// if (value != 2) goto val_err; + + /* Start with the symmetrical case */ + sz.side2 = sz.side1; + + value = spd_read_byte(device, 3); /* rows */ + if (value < 0) goto hw_err; + if ((value & 0xf0) == 0) goto out; /* If symmetrical we are done */ + sz.side2 -= (value & 0x0f); /* Subtract out rows on side 1 */ + sz.side2 += ((value >> 4) & 0x0f); /* Add in rows on side 2 */ + + value = spd_read_byte(device, 4); /* columns */ + if (value < 0) goto hw_err; +// if ((value & 0xff) == 0) goto val_err; + sz.side2 -= (value & 0x0f); /* Subtract out columns on side 1 */ + sz.side2 += ((value >> 4) & 0x0f); /* Add in columsn on side 2 */ + goto out; + + val_err: + die("Bad SPD value\r\n"); + /* If an hw_error occurs report that I have no memory */ +hw_err: + sz.side1 = 0; + sz.side2 = 0; + out: + return sz; +} + + + + /* + * This is a place holder fill this out + * Routine: spd_set_row_attributes + * Arguments: %bl SMBUS_MEM_DEVICE + * Results: + * %edi log base 2 size of DIMM side 1 in bits + * %esi log base 2 size of DIMM side 2 in bits + * + * Preserved: %ebx (except %bh), %ebp + * + * Trashed: %eax, %bh, %ecx, %edx, %esp, %eflags + * Used: %eax, %ebx, %ecx, %edx, %esi, %edi, %esp, %eflags + * + * Effects: Uses serial presence detect to set %edi & %esi + * the size of a dimm. + * Notes: + * %bl SMBUS_MEM_DEVICE + * %edi holds the memory size for the first side of the DIMM. + * %esi holds the memory size for the second side of the DIMM. + * memory size is represent as a power of 2. + * + * This routine may be worth moving into generic code somewhere. + */ +static long spd_set_row_attributes(const struct mem_controller *ctrl, long dimm_mask) { + int i; + uint32_t dword=0; + int value; + + + /* Walk through all dimms and find the interesection of the support + * for ecc sdram and refresh rates + */ + + + for(i = 0; i < DIMM_SOCKETS; i++) { + if (!(dimm_mask & (1 << i))) { + continue; + } + /* Test to see if I have ecc sdram */ + struct dimm_page_size sz; + sz = sdram_spd_get_page_size(ctrl->channel0[i]); /* SDRAM type */ +#if DEBUG_RAM_CONFIG + print_debug("page size ="); + print_debug_hex32(sz.side1); + print_debug(" "); + print_debug_hex32(sz.side2); + print_debug("\r\n"); +#endif + + /* Test to see if the dimm is present */ + if( sz.side1 !=0) { + + /* Test for a valid dimm width */ + if((sz.side1 <15) || (sz.side1>18) ) { + print_err("unsupported page size\r\n"); + } + + /* double because I have 2 channels */ + sz.side1++; + + /* Convert to the format needed for the DRA register */ + sz.side1-=14; + + /* Place in the %ebp the dra place holder */ //i + dword |= sz.side1<<(i<<3); + + /* Test to see if the second side is present */ + + if( sz.side2 !=0) { + + /* Test for a valid dimm width */ + if((sz.side2 <15) || (sz.side2>18) ) { + print_err("unsupported page size\r\n"); + } + + /* double because I have 2 channels */ + sz.side2++; + + /* Convert to the format needed for the DRA register */ + sz.side2-=14; + + /* Place in the %ebp the dra place holder */ //i + dword |= sz.side2<<((i<<3) + 4 ); + + } + } + + /* Now add the SDRAM chip width to the DRA */ + struct dimm_width wd; + wd = sdram_spd_get_width(ctrl->channel0[i]); + +#if DEBUG_RAM_CONFIG + print_debug("width ="); + print_debug_hex32(wd.side1); + print_debug(" "); + print_debug_hex32(wd.side2); + print_debug("\r\n"); +#endif + + if(wd.side1 == 0) continue; + if(wd.side1 == 4) { + /* Enable an x4 device */ + dword |= 0x08 << (i<<3); + } + + if(wd.side2 == 0) continue; + if(wd.side2 == 4) { + /* Enable an x4 device */ + dword |= 0x08 << ((i<<3 ) + 4); + } + + /* go to the next DIMM */ + } + + /* Write the new row attributes register */ + pci_write_config32(ctrl->d0, 0x70, dword); + + return dimm_mask; + +} +#if 0 + /* + * Routine: sdram_read_paired_byte + * Arguments: %esp return address + * %bl device on the smbus to read from + * %bh address on the smbus to read + * Results: + * zf clear + * byte read in %al + * On Error: + * zf set + * %eax trashed + * + * Preserved: %ebx, %esi, %edi + * + * Trashed: %eax, %ecx, %edx, %ebp, %esp, %eflags + * Used: %eax, %ebx, %ecx, %edx, %esp, %eflags + * + * Effects: Reads two spd bytes from both ram channesl + * and errors if they are not equal. + * It then returns the equal result. + */ +static spd_read_paired_byte () { + movl %esp, %ebp + CALLSP(smbus_read_byte) + setnz %cl + movb %al, %ch + addb $(SMBUS_MEM_CHANNEL_OFF), %bl + CALLSP(smbus_read_byte) + movb %ch, %ah + setnz %ch + subb $(SMBUS_MEM_CHANNEL_OFF), %bl + + /* See if dimms on both sides are equally present */ + cmp %cl, %ch + jne sdram_presence_mismatch + + /* Leave if I have no data */ + testb %cl, %cl + jz spd_verify_byte_out + + /* Verify the data is identical */ + cmp %ah, %al + jne sdram_value_mismatch + + /* Clear the zero flag */ + testb %cl, %cl +spd_verify_byte_out: + movl %ebp, %esp + RETSP +} + + /* + * Routine: spd_verify_dimms + * Arguments: none + * Results: none + * Preserved: none + * Trashed: %eax, %ebx, %ecx, %edx, %ebp, %esi, %edi, %esp, %eflags + * Used: %eax, %ebx, %ecx, %edx, %ebp, %esi, %edi, %esp, %eflags + * + * Effects: + * - Verify all interesting spd information + * matches for both dimm channels. + * - Additional error checks that can be easily done + * here are computed as well, so I don't need to + * worry about them later. + */ +static spd_verify_dimms() { + movl $(SMBUS_MEM_DEVICE_START), %ebx +spd_verify_dimm: + /* Verify this is DDR SDRAM */ + movb $2, %bh + CALLSP(spd_read_paired_byte) + jz spd_verify_next_dimm + cmpb $7, %al + jne invalid_dimm_type + + /* Verify the row addresses */ + movb $3, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb $0x0f, %al + jz spd_invalid_data + + /* Column addresses */ + movb $4, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb $0xf, %al + jz spd_invalid_data + + /* Physical Banks */ + movb $5, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + cmp $1, %al + jb spd_invalid_data + cmp $2, %al + ja spd_invalid_data + + /* Module Data Width */ + movb $7, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + cmpb $0, %al + jne spd_invalid_data + + movb $6, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + cmpb $64, %al + je 1f + cmpb $72, %al + je 1f + jmp spd_unsupported_data +1: + + /* Cycle time at highest CAS latency CL=X */ + movb $9, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + + /* SDRAM type */ + movb $11, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + + /* Refresh Interval */ + movb $12, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + + /* SDRAM Width */ + movb $13, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + andb $0x7f, %al + cmpb $4, %al + je 1f + cmpb $8, %al + je 1f + jmp spd_unsupported_data +1: + + /* Back-to-Back Random Column Accesses */ + movb $15, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb %al, %al + jz spd_invalid_data + cmpb $4, %al + ja spd_unsupported_data + + /* Burst Lengths */ + movb $16, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb $(1<<2), %al + jz spd_unsupported_data + + /* Logical Banks */ + movb $17, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb %al, %al + jz spd_invalid_data + + /* Supported CAS Latencies */ + movb $18, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb $(1 << 1), %al /* CL 1.5 */ + jnz 1f + testb $(1 << 2), %al /* CL 2.0 */ + jnz 1f + testb $(1 << 3), %al /* CL 2.5 */ + jnz 1f + jmp spd_unsupported_data +1: + + /* Cycle time at Cas Latency (CLX - 0.5) */ + movb $23, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + + /* Cycle time at Cas Latency (CLX - 1.0) */ + movb $26, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + + /* tRP Row precharge time */ + movb $27, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb $0xfc, %al + jz spd_invalid_data + + + /* tRCD RAS to CAS */ + movb $29, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb $0xfc, %al + jz spd_invalid_data + + /* tRAS Activate to Precharge */ + movb $30, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb %al, %al + jz spd_invalid_data + + /* Module Bank Density */ + movb $31, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + testb $(1<<2), %al /* 16MB */ + jnz spd_unsupported_data + testb $(1<<3), %al + jnz spd_unsupported_data /* 32MB */ + + /* Address and Command Hold Time After Clock */ + movb $33, %bh + CALLSP(spd_read_paired_byte) + jz spd_missing_data + +spd_verify_next_dimm: + /* go to the next DIMM */ + addb $(SMBUS_MEM_DEVICE_INC), %bl /* increment the smbus device */ + cmpb $SMBUS_MEM_DEVICE_END, %bl + jbe spd_verify_dimm +spd_verify_dimms_out: + RET_LABEL(spd_verify_dimms) +} +#endif +#define spd_pre_init "Reading SPD data...\r\n" +#define spd_pre_set "setting based on SPD data...\r\n" +#define spd_post_init "done\r\n" + + +static const uint32_t refresh_rate_rank[]= { + /* Refresh rates ordered from most conservative (lowest) + * to most agressive (highest) + * disabled 0 -> rank 3 + * 15.6usec 1 -> rank 1 + * 7.8 usec 2 -> rank 0 + * 64usec 3 -> rank 2 + */ + 3, 1, 0, 2 }; +static const uint32_t refresh_rate_index[] = { + /* Map the spd refresh rates to memory controller settings + * 15.625us -> 15.6us + * 3.9us -> err + * 7.8us -> 7.8us + * 31.3s -> 15.6us + * 62.5us -> 15.6us + * 125us -> 64us + */ + 1, 0xff, 2, 1, 1, 3 +}; +#define MAX_SPD_REFRESH_RATE 5 + +static long spd_set_dram_controller_mode (const struct mem_controller *ctrl, long dimm_mask) { + + int i; + uint32_t dword; + int value; + uint32_t ecx; + uint32_t edx; + + /* Read the inititial state */ + dword = pci_read_config32(ctrl->d0, 0x7c); + +#if 0 + /* Test if ECC cmos option is enabled */ + movb $RTC_BOOT_BYTE, %al + outb %al, $0x70 + inb $0x71, %al + testb $(1<<2), %al + jnz 1f + /* Clear the ecc enable */ + andl $~(3 << 20), %esi +1: +#endif + + + /* Walk through all dimms and find the interesection of the support + * for ecc sdram and refresh rates + */ + + + for(i = 0; i < DIMM_SOCKETS; i++) { + if (!(dimm_mask & (1 << i))) { + continue; + } + /* Test to see if I have ecc sdram */ + value = spd_read_byte(ctrl->channel0[i], 11); /* SDRAM type */ + if(value < 0) continue; + if(value !=2 ) { + /* Clear the ecc enable */ + dword &= ~(3 << 20); + } + value = spd_read_byte(ctrl->channel0[i], 12); /* SDRAM refresh rate */ + if(value < 0 ) continue; + value &= 0x7f; + if(value > MAX_SPD_REFRESH_RATE) { print_err("unsupported refresh rate\r\n");} +// if(value == 0xff) { print_err("unsupported refresh rate\r\n");} + + ecx = refresh_rate_index[value]; + + /* Isolate the old refresh rate setting */ + /* Load the refresh rate ranks */ + edx = refresh_rate_rank[(dword >> 8) & 3]<<8; + edx |= refresh_rate_rank[ecx] & 0xff; + + /* See if the new refresh rate is more conservative than the old + * refresh rate setting. (Lower ranks are more conservative) + */ + if((edx & 0xff)< ((edx >> 8) & 0xff) ) { + /* Clear the old refresh rate */ + dword &= ~(3<<8); + /* Move in the new refresh rate */ + dword |= (ecx<<8); + } + + value = spd_read_byte(ctrl->channel0[i], 33); /* Address and command hold time after clock */ + if(value < 0) continue; + if(value >= 0xa0) { /* At 133Mhz this constant should be 0x75 */ + dword &= ~(1<<16); /* Use two clock cyles instead of one */ + } + + /* go to the next DIMM */ + } + + /* Now write the controller mode */ + pci_write_config32(ctrl->d0, 0x7c, dword); + + return dimm_mask; + +} +static long spd_enable_clocks(const struct mem_controller *ctrl, long dimm_mask) +{ + int i; + uint32_t dword; + int value; + + /* Read the inititial state */ + dword = pci_read_config32(ctrl->d0, 0x8c); +#if 0 +# Intel clears top bit here, should we? +# No the default is on and for normal timming it should be on. Tom Z + andl $0x7f, %esi +#endif + + + for(i = 0; i < DIMM_SOCKETS; i++) { + if (!(dimm_mask & (1 << i))) { + continue; + } + /* Read any spd byte to see if the dimm is present */ + value = spd_read_byte(ctrl->channel0[i], 5); /* Physical Banks */ + if(value < 0) continue; + + dword &= ~(1<d0, 0x8c, dword); + + return dimm_mask; +} + +static const uint16_t cas_latency_80[] = { + /* For cas latency 2.0 0x01 works and until I see a large test sample + * I am not prepared to change this value, to the intel recommended value + * of 0x0d. Eric Biederman + */ + /* The E7501 requires b1 rather than 01 for CAS2 or memory will be hosed + * CAS 1.5 is claimed to be unsupported, will try to test that + * will need to determine correct values for other CAS values + * (perhaps b5, b1, b6?) + * Steven James 02/06/2003 + */ + +//# .byte 0x05, 0x01, 0x06 +//# .byte 0xb5, 0xb1, 0xb6 + 0x0, 0x0bb1, 0x0662 /* RCVEN */ +}; +static const uint16_t cas_latency_80_4dimms[] = { + 0x0, 0x0bb1, 0x0882 +}; + + +static const uint8_t cas_latency_78[] = { + DRT_CAS_1_5, DRT_CAS_2_0, DRT_CAS_2_5 +}; + +static long spd_set_cas_latency(const struct mem_controller *ctrl, long dimm_mask) { + /* Walk through all dimms and find the interesection of the + * supported cas latencies. + */ + int i; + /* Initially allow cas latencies 2.5, 2.0 + * which the chipset supports. + */ + uint32_t dword = (1<<3)| (1<<2);// esi + uint32_t edi; + uint32_t ecx; + unsigned device; + int value; + uint8_t byte; + uint16_t word; + + + for(i = 0; i < DIMM_SOCKETS; i++) { + if (!(dimm_mask & (1 << i))) { + continue; + } + value = spd_read_byte(ctrl->channel0[i], 18); + if(value < 0) continue; + /* Find the highest supported cas latency */ + ecx = log2(value & 0xff); + edi = (1<< ecx); + + /* Remember the supported cas latencies */ + ecx = (value & 0xff); + + /* Verify each cas latency at 133Mhz */ + /* Verify slowest/highest CAS latency */ + value = spd_read_byte(ctrl->channel0[i], 9); + if(value < 0 ) continue; + if(value > 0x75 ) { + /* The bus is too fast so we cannot support this case latency */ + ecx &= ~edi; + } + + /* Verify the highest CAS latency - 0.5 clocks */ + edi >>= 1; + if(edi != 0) { + value = spd_read_byte(ctrl->channel0[i], 23); + if(value < 0 ) continue; + if(value > 0x75) { + /* The bus is too fast so we cannot support this cas latency */ + ecx &= ~edi; + } + } + + /* Verify the highest CAS latency - 1.0 clocks */ + edi >>=1; + if(edi !=0) { + value = spd_read_byte(ctrl->channel0[i], 25); + if(value < 0 ) continue; + if(value > 0x75) { + /* The bus is too fast so we cannot support this cas latency */ + ecx &= ~edi; + } + } + + /* Now find which cas latencies are supported for the bus */ + dword &= ecx; + /* go to the next DIMM */ + } + + /* After all of the arduous calculation setup with the fastest + * cas latency I can use. + */ + value = __builtin_bsf(dword); // bsrl = log2 how about bsfl? + if(value ==0 ) return -1; + ecx = value -1; + + byte = pci_read_config8(ctrl->d0, 0x78); + byte &= ~(DRT_CAS_MASK); + byte |= cas_latency_78[ecx]; + pci_write_config8(ctrl->d0,0x78, byte); + + /* set master DLL reset */ + dword = pci_read_config32(ctrl->d0, 0x88); + dword |= (1<<26); + + /* the rest of the references are words */ +// ecx<<=1; // don't need shift left, because we already define that in u16 array + pci_write_config32(ctrl->d0, 0x88, dword); + + + dword &= 0x0c0000ff; /* patch try register 88 is undocumented tnz */ + dword |= 0xd2109800; + + pci_write_config32(ctrl->d0, 0x88, dword); + + word = pci_read_config16(ctrl->d0, 0x80); + word &= ~(0x0fff); + word |= cas_latency_80[ecx]; + + dword = pci_read_config32(ctrl->d0, 0x70); + + if((dword & 0xff) !=0 ) { + dword >>=8; + if((dword & 0xff)!=0) { + dword >>=8; + if((dword & 0xff)!=0) { + dword >>= 8; + if( (dword & 0xff)!=0) { + word &=~(0x0fff); /* we have dimms in all 4 slots */ + word |=cas_latency_80_4dimms[ecx]; + } + } + } + } + + pci_write_config16(ctrl->d0, 0x80, word); + + dword = pci_read_config32(ctrl->d0, 0x88); /* reset master DLL reset */ + dword &= ~(1<<26); + pci_write_config32(ctrl->d0, 0x88, dword); + + RAM_RESET_DDR_PTR(ctrl); + + return dimm_mask; + +} + +static long spd_set_dram_timing(const struct mem_controller *ctrl, long dimm_mask) { + /* Walk through all dimms and find the interesection of the + * supported dram timings. + */ + + int i; + uint32_t dword; + int value; + + /* Read the inititial state */ + dword = pci_read_config32(ctrl->d0, 0x78); +#if 0 +# Intel clears top bit here, should we? +# No the default is on and for normal timming it should be on. Tom Z + andl $0x7f, %esi +#endif + + + for(i = 0; i < DIMM_SOCKETS; i++) { + if (!(dimm_mask & (1 << i))) { + continue; + } + /* Trp */ + value = spd_read_byte(ctrl->channel0[i], 27); + if(value < 0) continue; + if(value > (15<<2)) { + /* At 133Mhz if row precharge time is above than 15ns than we + * need 3 clocks not 2 clocks. + */ + dword &= ~(1<<0); + } + /* Trcd */ + value = spd_read_byte(ctrl->channel0[i],29); + if(value < 0 ) continue; + if(value > (15<<2)) { + /* At 133Mhz if the Minimum ras to cas delay is about 15ns we + * need 3 clocks not 2 clocks. + */ + dword &= ~((1<<3)|(1<<1)); + } + /* Tras */ + value = spd_read_byte(ctrl->channel0[i],30); + if(value < 0 ) continue; + /* Convert tRAS from ns to 133Mhz clock cycles */ + value <<=1; /* mult by 2 to make 7.5 15 */ + value += 15; /* Make certain we round up */ + value --; + value &= 0xff; /* Clear the upper bits of eax */ + value /= 15; + + /* Don't even process small timings */ + if(value >5) { + uint32_t tmp; + /* Die if the value is to large */ + if(value>7) { + die ("unsupported_rcd\r\n"); + } + /* Convert to clocks - 5 */ + value -=5; + /* Convert the existing value into clocks - 5 */ + tmp = (~((dword>>9) & 3) - 1) & 3; + /* See if we need a slower timing */ + if(value > tmp ) { + /* O.k. put in our slower timing */ + dword &= ~(3<<9); + dword |= ((~(value + 1)) & 3)<<9 ; + } + } + + /* Trd */ + /* Set to a 7 clock read delay. This is for 133Mhz + * with a CAS latency of 2.5 if 2.0 a 6 clock + * delay is good */ + if( (pci_read_config8(ctrl->d0, 0x78) & 0x30) ==0 ){ + dword &= ~(7<<24); /* CAS latency is 2.5, make 7 clks */ + } + + /* + * Back to Back Read Turn Around + */ + /* Set to a 3 clock back to back read turn around. This + * is good for CAS latencys 2.5 and 2.0 */ + dword |= (1<<27); + /* + * Back to Back Read-Write Turn Around + */ + /* Set to a 5 clock back to back read to write turn around. + * 4 is a good delay if the CAS latency is 2.0 */ + if( ( pci_read_config8(ctrl->d0, 0x78) & (1<<4)) == 0) { + dword &= ~(1<<28); + } + /* + * Back to Back Write-Read Turn Around + */ + /* Set to a 2 clock back to back write to read turn around. + * This is good for 2.5 and 2.0 CAS Latencies. */ + dword |= (1<<29); + } + + pci_write_config32(ctrl->d0, 0x78, dword); + + return dimm_mask; + +} +static unsigned int spd_detect_dimms(const struct mem_controller *ctrl) +{ + unsigned dimm_mask; + int i; + dimm_mask = 0; +#if DEBUG_RAM_CONFIG + print_debug("spd_detect_dimms:\r\n"); +#endif + for(i = 0; i < DIMM_SOCKETS; i++) { + int byte; + unsigned device; +#if DEBUG_RAM_CONFIG + print_debug_hex32(i); + print_debug("\r\n"); +#endif + device = ctrl->channel0[i]; + if (device) { + byte = spd_read_byte(ctrl->channel0[i], 2); /* Type */ + if (byte == 7) { + dimm_mask |= (1 << i); + } + } +#if 1 + device = ctrl->channel1[i]; + if (device) { + byte = spd_read_byte(ctrl->channel1[i], 2); + if (byte == 7) { + dimm_mask |= (1 << (i + DIMM_SOCKETS)); + } + } +#endif + } +#if 1 + i = (dimm_mask>>DIMM_SOCKETS); + if(i != (dimm_mask & ( (1<= (25 + 4)) { + memsz += (1 << (sz.side1 - (25 + 4)) ) ; + } + /* Write the size of side 1 of the dimm */ + byte = memsz; + pci_write_config8(ctrl->d0, 0x60+(index<<1), byte); + + /* Make certain side2 of the dimm is at least 64MB */ + if (sz.side2 >= (25 + 4)) { + memsz += (1 << (sz.side2 - (25 + 4)) ) ; + } + + /* Write the size of side 2 of the dimm */ + byte = memsz; + pci_write_config8(ctrl->d0, 0x61+(index<<1), byte); + + /* now, fill in DRBs where no physical slot exists */ + + for(i=index+1;i<4;i++) { + pci_write_config8(ctrl->d0, 0x60+(i<<1),byte); + pci_write_config8(ctrl->d0, 0x61+(i<<1),byte); + + } + + return memsz; + +} +/* LAST_DRB_SLOT is a constant for any E7500 board */ +#define LAST_DRB_SLOT 0x67 + +static long spd_set_ram_size(const struct mem_controller *ctrl, long dimm_mask) +{ + int i; + uint32_t memsz=0; + uint16_t word; + + for(i = 0; i < DIMM_SOCKETS; i++) { + struct dimm_size sz; + if (!(dimm_mask & (1 << i))) { + continue; + } + sz = spd_get_dimm_size(ctrl->channel0[i]); +#if DEBUG_RAM_CONFIG + print_debug("dimm size ="); + print_debug_hex32(sz.side1); + print_debug(" "); + print_debug_hex32(sz.side2); + print_debug("\r\n"); +#endif + + if (sz.side1 == 0) { + return -1; /* Report SPD error */ + } + memsz = set_dimm_size(ctrl, sz, memsz, i); + } + /* For now hardset everything at 128MB boundaries */ + /* %ebp has the ram size in multiples of 64MB */ +// cmpl $0, %ebp /* test if there is no mem - smbus went bad */ +// jz no_memory_bad_smbus + if(memsz < 0x30) { + /* I should really adjust all of this in C after I have resources + * to all of the pcie devices. + */ + + /* Round up to 128M granularity */ + memsz++; + memsz &= 0xfe; + memsz<<= 10; + word = memsz; + pci_write_config16(ctrl->d0, 0xc4, word); + } else { + + /* FIXME will this work with 3.5G of ram? */ + /* Put TOLM at 3G */ + pci_write_config16(ctrl->d0, 0xc4, 0xc000); + /* Hard code a 1G remap window, right after the ram */ + if(memsz< 0x40){ + word = 0x40; /* Ensure we are over 4G */ + } else { + word = memsz; + } + pci_write_config16(ctrl->d0, 0xc6, word); + word += 0x10; + pci_write_config16(ctrl->d0, 0xc8, word); + + } + + return dimm_mask; +} + +static void sdram_set_spd_registers(const struct mem_controller *ctrl) { + long dimm_mask; +#if DEBUG_RAM_CONFIG + print_debug(spd_pre_init); +#endif + //activate_spd_rom(ctrl); + dimm_mask = spd_detect_dimms(ctrl); + if (!(dimm_mask & ((1 << DIMM_SOCKETS) - 1))) { + print_debug("No memory for this controller\n"); + return; + } + dimm_mask = spd_enable_clocks(ctrl, dimm_mask); + if (dimm_mask < 0) + goto hw_spd_err; + //spd_verify_dimms(ctrl); +#if DEBUG_RAM_CONFIG + print_debug(spd_pre_set); +#endif + dimm_mask = spd_set_row_attributes(ctrl,dimm_mask); + if (dimm_mask < 0) + goto hw_spd_err; + dimm_mask = spd_set_dram_controller_mode(ctrl,dimm_mask); + if (dimm_mask < 0) + goto hw_spd_err; + dimm_mask = spd_set_cas_latency(ctrl,dimm_mask); + if (dimm_mask < 0) + goto hw_spd_err; + dimm_mask = spd_set_dram_timing(ctrl,dimm_mask); + if (dimm_mask < 0) + goto hw_spd_err; +#if DEBUG_RAM_CONFIG + print_debug(spd_post_init); +#endif + //moved from dram_post_init + spd_set_ram_size(ctrl, dimm_mask); + return; + hw_spd_err: + /* Unrecoverable error reading SPD data */ + print_err("SPD error - reset\r\n"); + hard_reset(); + return; +} + + + /* I have finally seen ram bad enough to cause LinuxBIOS + * to die in mysterious ways, before booting up far + * enough to run a memory tester. This code attempts + * to catch this blatantly bad ram, with a spot check. + * For most cases you should boot all of the way up + * and run a memory tester. + */ + /* Ensure I read/write each stick of bank of memory && + * that I do more than 1000 bytes to avoid the northbridge cache. + * Only 64M of each side of each DIMM is currently mapped, + * so we can handle > 4GB of ram here. + */ +#if 0 +#define bank_msg "Bank " +#define side_msg " Side " +static void verify_ram() { + xorl %ecx, %ecx + /* Check to see if the RAM is present, + * in the specified bank and side. + */ +1: movl %ecx, %ebx + shrl $1, %ebx + addl $((5<<8) | SMBUS_MEM_DEVICE_START), %ebx + CALLSP(smbus_read_byte) + jz 5f + testl $1, %ecx + jz 2f + cmpb $2, %al + jne 5f + + /* Display the bank and side we are spot checking. + */ +2: CONSOLE_INFO_TX_STRING($bank_msg) + movl %ecx, %ebx + shrl $1, %ebx + incl %ebx + CONSOLE_INFO_TX_HEX8(%bl) + CONSOLE_INFO_TX_STRING($side_msg) + movl %ecx, %ebx + andl $1, %ebx + CONSOLE_INFO_TX_HEX8(%bl) + + /* Compute the memory address to spot check. */ + movl %ecx, %ebx + xorl %eax, %eax +3: testl %ebx, %ebx + jz 4f + addl $0x04000000, %eax + decl %ebx + jmp 3b +4: + /* Spot check 512K of RAM */ + movl %eax, %ebx + addl $0x0007ffff, %ebx + CALLSP(spot_check) +5: + /* Now find the next bank and side to spot check */ + incl %ecx + cmpl $((SMBUS_MEM_DEVICE_END - SMBUS_MEM_DEVICE_START)<<1), %ecx + jb 1b + RET_LABEL(verify_ram) + +} +#endif + +#if 0 +static void ram_postinit(const struct mem_controller *ctrl) { +#if DEBUG_RAM_CONFIG + dumpnorth(); +#endif + /* Include a test to verify that memory is more or less working o.k. + * This test is to catch programming errors and hardware that is out of + * spec, not a test to see if the memory dimms are working 100% + */ +//# CALL_LABEL(verify_ram) + spd_set_ram_size(ctrl); +} +#define FIRST_NORMAL_REFERENCE() CALL_LABEL(ram_postinit) + +#define SPECIAL_FINISHUP() CALL_LABEL(dram_finish) + +#endif + +#define ecc_pre_init "Initializing ECC state...\r\n" +#define ecc_post_init "ECC state initialized.\r\n" +static void dram_finish(const struct mem_controller *ctrl) +{ + uint32_t dword; + uint8_t byte; + /* Test to see if ECC support is enabled */ + dword = pci_read_config32(ctrl->d0, 0x7c); + dword >>=20; + dword &=3; + if(dword == 2) { + +#if DEBUG_RAM_CONFIG + print_debug(ecc_pre_init); +#endif + /* Initialize ECC bits , use ECC zero mode (new to 7501)*/ + pci_write_config8(ctrl->d0, 0x52, 0x06); + pci_write_config8(ctrl->d0, 0x52, 0x07); + do { + byte = pci_read_config8(ctrl->d0, 0x52); + + } while ( (byte & 0x08 ) == 0); + + pci_write_config8(ctrl->d0, 0x52, byte & 0xfc); +#if DEBUG_RAM_CONFIG + print_debug(ecc_post_init); +#endif + + /* Clear the ECC error bits */ + pci_write_config8(ctrl->d0f1, 0x80, 0x03); /* dev 0, function 1, offset 80 */ + pci_write_config8(ctrl->d0f1, 0x82, 0x03); /* dev 0, function 1, offset 82 */ + + pci_write_config32(ctrl->d0f1, 0x40, 1<<18); /* clear dev 0, function 1, offset 40; bit 18 by writing a 1 to it */ + pci_write_config32(ctrl->d0f1, 0x44, 1<<18); /* clear dev 0, function 1, offset 44; bit 18 by writing a 1 to it */ + + pci_write_config8(ctrl->d0, 0x52, 0x0d); + } + + dword = pci_read_config32(ctrl->d0, 0x7c); /* FCS_EN */ + dword |= (1<<17); + pci_write_config32(ctrl->d0, 0x7c, dword); + + +#if DEBUG_RAM_CONFIG + dumpnorth(); +#endif + +// verify_ram(); +} +#if 0 +#define ERRFUNC(x, str) mem_err(x, str) + + +ERRFUNC(invalid_dimm_type, "Invalid dimm type") +ERRFUNC(spd_missing_data, "Missing sdram spd data") +ERRFUNC(spd_invalid_data, "Invalid sdram spd data") +ERRFUNC(spd_unsupported_data, "Unsupported sdram spd value") +ERRFUNC(unsupported_page_size, "Unsupported page size") +ERRFUNC(sdram_presence_mismatch, "DIMM presence mismatch") +ERRFUNC(sdram_value_mismatch, "spd data does not match") +ERRFUNC(unsupported_refresh_rate, "Unsuported spd refresh rate") +ERRFUNC(inconsistent_cas_latencies, "No cas latency supported by all dimms") +ERRFUNC(unsupported_rcd, "Unsupported ras to cas delay") +#undef ERRFUNC + +#define mem_err_err "ERROR: " +#define mem_err_pair " on dimm pair " +#define mem_err_byte " spd byte " +static void mem_err { + movl %ebx, %edi + CONSOLE_ERR_TX_STRING($mem_err_err) + CONSOLE_ERR_TX_STRING(%esi) + CONSOLE_ERR_TX_STRING($mem_err_pair) + movl %edi, %ebx + subb $(SMBUS_MEM_DEVICE_START), %bl + CONSOLE_ERR_TX_HEX8(%bl) + CONSOLE_ERR_TX_STRING($mem_err_byte) + movl %edi, %ebx + CONSOLE_ERR_TX_HEX8(%bh) + jmp mem_stop + +} + +#endif + + +#if ASM_CONSOLE_LOGLEVEL > BIOS_DEBUG +#define ram_enable_1 "Ram Enable 1\r\n" +#define ram_enable_2 "Ram Enable 2\r\n" +#define ram_enable_3 "Ram Enable 3\r\n" +#define ram_enable_4 "Ram Enable 4\r\n" +#define ram_enable_5 "Ram Enable 5\r\n" +#define ram_enable_6 "Ram Enable 6\r\n" +#define ram_enable_7 "Ram Enable 7\r\n" +#define ram_enable_8 "Ram Enable 8\r\n" +#define ram_enable_9 "Ram Enable 9\r\n" +#define ram_enable_10 "Ram Enable 10\r\n" +#define ram_enable_11 "Ram Enable 11\r\n" +#endif + + /* Estimate that SLOW_DOWN_IO takes about 50&76us*/ + /* delay for 200us */ + +#define DO_DELAY \ + udelay(200); +// for(i=0; i<16;i++) { SLOW_DOWN_IO } + + +#define EXTRA_DELAY DO_DELAY + +static void sdram_enable(int controllers, const struct mem_controller *ctrl) +{ + int i; + /* 1 & 2 Power up and start clocks */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_1); + print_debug(ram_enable_2); +#endif + + /* A 200us delay is needed */ + + DO_DELAY + EXTRA_DELAY + + /* 3. Apply NOP */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_3); +#endif + RAM_NOP(ctrl); + EXTRA_DELAY + + /* 4 Precharge all */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_4); +#endif + RAM_PRECHARGE(ctrl); + EXTRA_DELAY + + /* wait until the all banks idle state... */ + /* 5. Issue EMRS to enable DLL */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_5); +#endif + RAM_EMRS(ctrl); + EXTRA_DELAY + + /* 6. Reset DLL */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_6); +#endif + RAM_MRS(ctrl,1); + EXTRA_DELAY + + /* Ensure a 200us delay between the DLL reset in step 6 and the final + * mode register set in step 9. + * Infineon needs this before any other command is sent to the ram. + */ + DO_DELAY + EXTRA_DELAY + + /* 7 Precharge all */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_7); +#endif + RAM_PRECHARGE(ctrl); + EXTRA_DELAY + + /* 8 Now we need 2 AUTO REFRESH / CBR cycles to be performed */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_8); +#endif + RAM_CBR(ctrl); + EXTRA_DELAY + RAM_CBR(ctrl); + EXTRA_DELAY + /* And for good luck 6 more CBRs */ + RAM_CBR(ctrl); + EXTRA_DELAY + RAM_CBR(ctrl); + EXTRA_DELAY + RAM_CBR(ctrl); + EXTRA_DELAY + RAM_CBR(ctrl); + EXTRA_DELAY + RAM_CBR(ctrl); + EXTRA_DELAY + RAM_CBR(ctrl); + EXTRA_DELAY + + /* 9 mode register set */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_9); +#endif + RAM_MRS(ctrl,0); + EXTRA_DELAY + + /* 10 DDR Receive FIFO RE-Sync */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_10); +#endif + RAM_RESET_DDR_PTR(ctrl); + EXTRA_DELAY + + /* 11 normal operation */ +#if DEBUG_RAM_CONFIG + print_debug(ram_enable_11); +#endif + RAM_NORMAL(ctrl); + + + // special from v1 + //FIRST_NORMAL_REFERENCE(); + //spd_set_ram_size(ctrl, 0x03); + + /* Finally enable refresh */ + ENABLE_REFRESH(ctrl); + + //SPECIAL_FINISHUP(); + dram_finish(ctrl); + +} + diff --git a/src/northbridge/intel/e7501/raminit.h b/src/northbridge/intel/e7501/raminit.h new file mode 100644 index 0000000000..c1dc4baeaf --- /dev/null +++ b/src/northbridge/intel/e7501/raminit.h @@ -0,0 +1,12 @@ +#ifndef RAMINIT_H +#define RAMINIT_H + +#define DIMM_SOCKETS 4 +struct mem_controller { + device_t d0, d0f1; + uint16_t channel0[DIMM_SOCKETS]; + uint16_t channel1[DIMM_SOCKETS]; +}; + + +#endif /* RAMINIT_H */ diff --git a/src/northbridge/intel/e7501/reset_test.c b/src/northbridge/intel/e7501/reset_test.c new file mode 100644 index 0000000000..79a5cdaee1 --- /dev/null +++ b/src/northbridge/intel/e7501/reset_test.c @@ -0,0 +1,18 @@ +/* Convert to C by yhlu */ +#define MCH_DRC 0x7c +#define DRC_DONE (1 << 29) + /* If I have already booted once skip a bunch of initialization */ + /* To see if I have already booted I check to see if memory + * has been enabled. + */ +static int bios_reset_detected(void) { + uint32_t dword; + + dword = pci_read_config32(PCI_DEV(0, 0, 0), MCH_DRC); + + if( (dword & DRC_DONE) != 0 ) { + return 1; + } + + return 0; +} diff --git a/src/southbridge/intel/i82801er/Config.lb b/src/southbridge/intel/i82801er/Config.lb new file mode 100644 index 0000000000..cc77c755a7 --- /dev/null +++ b/src/southbridge/intel/i82801er/Config.lb @@ -0,0 +1,11 @@ +config i82801er.h +driver i82801er.o +driver i82801er_usb.o +driver i82801er_lpc.o +driver i82801er_ide.o +driver i82801er_sata.o +driver i82801er_usb2.o +driver i82801er_ac97.o +#driver i82801er_nic.o +#driver i82801er_pci.o +object i82801er_reset.o diff --git a/src/southbridge/intel/i82801er/cmos_failover.c b/src/southbridge/intel/i82801er/cmos_failover.c new file mode 100644 index 0000000000..9702313f9c --- /dev/null +++ b/src/southbridge/intel/i82801er/cmos_failover.c @@ -0,0 +1,16 @@ +//kind of cmos_err for ich5 +#define RTC_FAILED (1 <<2) +#define GEN_PMCON_3 0xa4 +static void check_cmos_failed(void) +{ + + uint8_t byte; + byte = pci_read_config8(PCI_DEV(0,0x1f,0),GEN_PMCON_3); + if( byte & RTC_FAILED){ +//clear bit 1 and bit 2 + byte = cmos_read(RTC_BOOT_BYTE); + byte &= 0x0c; + byte |= MAX_REBOOT_CNT << 4; + cmos_write(byte, RTC_BOOT_BYTE); + } +} diff --git a/src/southbridge/intel/i82801er/i82801er.c b/src/southbridge/intel/i82801er/i82801er.c new file mode 100644 index 0000000000..565d672260 --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er.c @@ -0,0 +1,57 @@ +#include +#include +#include +#include +#include +#include "i82801er.h" + +void i82801er_enable(device_t dev) +{ + device_t lpc_dev; + unsigned int index; + uint16_t reg_old, reg; + +// all 82801er device ares in bus 0 + unsigned int devfn; + devfn = PCI_DEVFN(0x1f, 0); // lpc + lpc_dev = dev_find_slot(0, devfn); // 0 + if (!lpc_dev ) { + return; + } +#if 0 + if ((lpc_dev->vendor != PCI_VENDOR_ID_INTEL) || + (lpc_dev->device != PCI_DEVICE_ID_INTEL_82801ER_1F0)) { + uint32_t id; + id = pci_read_config32(lpc_dev, PCI_VENDOR_ID); + if (id != (PCI_VENDOR_ID_INTEL | (PCI_DEVICE_ID_INTEL_82801ER_1F0 << 16))) { + return; + } + } +#endif + + index = (dev->path.u.pci.devfn & 7); + if((dev->path.u.pci.devfn & ~0x7)==devfn) { // D=0x1f + if(index==0){ //1f0 + index = 14; + } + } else { // D=0x1d + index += 8; + } + + reg_old = pci_read_config16(lpc_dev, FUNC_DIS); + reg = reg_old; + reg &= ~(1<enabled) { + reg |= (1< +#include +#include +#include +#include +#include "i82801er.h" + + +static struct device_operations ac97audio_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .enable = i82801er_enable, + .init = 0, + .scan_bus = 0, +}; + +static struct pci_driver ac97audio_driver __pci_driver = { + .ops = &ac97audio_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1F5, +}; + + +static struct device_operations ac97modem_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .enable = i82801er_enable, + .init = 0, + .scan_bus = 0, +}; + +static struct pci_driver ac97modem_driver __pci_driver = { + .ops = &ac97modem_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1F6, +}; diff --git a/src/southbridge/intel/i82801er/i82801er_early_smbus.c b/src/southbridge/intel/i82801er/i82801er_early_smbus.c new file mode 100644 index 0000000000..ed014f1a86 --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_early_smbus.c @@ -0,0 +1,156 @@ + +//#define SMBUS_IO_BASE 0x1000 +#define SMBUS_IO_BASE 0x0f00 + +#define SMBHSTSTAT 0x0 +#define SMBHSTCTL 0x2 +#define SMBHSTCMD 0x3 +#define SMBXMITADD 0x4 +#define SMBHSTDAT0 0x5 +#define SMBHSTDAT1 0x6 +#define SMBBLKDAT 0x7 +#define SMBTRNSADD 0x9 +#define SMBSLVDATA 0xa +#define SMLINK_PIN_CTL 0xe +#define SMBUS_PIN_CTL 0xf + +/* Between 1-10 seconds, We should never timeout normally + * Longer than this is just painful when a timeout condition occurs. + */ +#define SMBUS_TIMEOUT (100*1000*10) + +static void enable_smbus(void) +{ + device_t dev; + dev = pci_locate_device(PCI_ID(0x8086, 0x24d3), 0); + if (dev == PCI_DEV_INVALID) { + die("SMBUS controller not found\r\n"); + } + + print_debug("SMBus controller enabled\r\n"); + /* set smbus iobase */ + pci_write_config32(dev, 0x20, SMBUS_IO_BASE | 1); + /* Set smbus enable */ + pci_write_config8(dev, 0x40, 0x01); + /* Set smbus iospace enable */ + pci_write_config16(dev, 0x4, 0x01); + /* Disable interrupt generation */ + outb(0, SMBUS_IO_BASE + SMBHSTCTL); + /* clear any lingering errors, so the transaction will run */ + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT); +} + + +static inline void smbus_delay(void) +{ + outb(0x80, 0x80); +} + +static int smbus_wait_until_ready(void) +{ + unsigned long loops; + loops = SMBUS_TIMEOUT; + do { + unsigned char val; + smbus_delay(); + val = inb(SMBUS_IO_BASE + SMBHSTSTAT); + if ((val & 1) == 0) { + break; + } + if(loops == (SMBUS_TIMEOUT / 2)) { + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), + SMBUS_IO_BASE + SMBHSTSTAT); + } + } while(--loops); + return loops?0:-2; +} + +static int smbus_wait_until_done(void) +{ + unsigned long loops; + loops = SMBUS_TIMEOUT; + do { + unsigned char val; + smbus_delay(); + + val = inb(SMBUS_IO_BASE + SMBHSTSTAT); + if ( (val & 1) == 0) { + break; + } + if ((val & ~((1<<6)|(1<<0)) ) != 0 ) { + break; + } + } while(--loops); + return loops?0:-3; +} + +static int smbus_read_byte(unsigned device, unsigned address) +{ + unsigned char global_control_register; + unsigned char global_status_register; + unsigned char byte; + + if (smbus_wait_until_ready() < 0) { + return -2; + } + + /* setup transaction */ + /* disable interrupts */ + outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xfe, SMBUS_IO_BASE + SMBHSTCTL); + /* set the device I'm talking too */ + outb(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBXMITADD); + /* set the command/address... */ + outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD); + /* set up for a byte data read */ + outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xe3) | (0x2<<2), SMBUS_IO_BASE + SMBHSTCTL); + + /* clear any lingering errors, so the transaction will run */ + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT); + + /* clear the data byte...*/ + outb(0, SMBUS_IO_BASE + SMBHSTDAT0); + + /* start a byte read, with interrupts disabled */ + outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), SMBUS_IO_BASE + SMBHSTCTL); + + + /* poll for transaction completion */ + if (smbus_wait_until_done() < 0) { + return -3; + } + + global_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT) & ~(1<<6); /* Ignore the In Use Status... */ + + /* read results of transaction */ + byte = inb(SMBUS_IO_BASE + SMBHSTDAT0); + + if (global_status_register != 2) { + return -1; + } + return byte; +} +#if 0 +static void smbus_write_byte(unsigned device, unsigned address, unsigned char val) +{ + if (smbus_wait_until_ready() < 0) { + return; + } + + /* by LYH */ + outb(0x37,SMBUS_IO_BASE + SMBHSTSTAT); + /* set the device I'm talking too */ + outw(((device & 0x7f) << 1) | 0, SMBUS_IO_BASE + SMBHSTADDR); + + /* data to send */ + outb(val, SMBUS_IO_BASE + SMBHSTDAT); + + outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD); + + /* start the command */ + outb(0xa, SMBUS_IO_BASE + SMBHSTCTL); + + /* poll for transaction completion */ + smbus_wait_until_done(); + return; +} +#endif diff --git a/src/southbridge/intel/i82801er/i82801er_ide.c b/src/southbridge/intel/i82801er/i82801er_ide.c new file mode 100644 index 0000000000..b33a0b0f09 --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_ide.c @@ -0,0 +1,53 @@ +#include +#include +#include +#include +#include +#include "i82801er.h" + + +static void ide_init(struct device *dev) +{ +#if ICH5_SATA_ADDRESS_MAP<=1 + /* Enable ide devices so the linux ide driver will work */ + uint16_t word; + uint8_t byte; + int enable_a=1, enable_b=1; + + + word = pci_read_config16(dev, 0x40); + word &= ~((1 << 15)); + if (enable_a) { + /* Enable first ide interface */ + word |= (1<<15); + printk_debug("IDE0 "); + } + pci_write_config16(dev, 0x40, word); + + word = pci_read_config16(dev, 0x42); + word &= ~((1 << 15)); + if (enable_a) { + /* Enable secondary ide interface */ + word |= (1<<15); + printk_debug("IDE1 "); + } + pci_write_config16(dev, 0x42, word); +#endif + +} + +static struct device_operations ide_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = ide_init, + .scan_bus = 0, + .enable = i82801er_enable, +}; + +static struct pci_driver ide_driver __pci_driver = { + .ops = &ide_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1F1, +}; + diff --git a/src/southbridge/intel/i82801er/i82801er_lpc.c b/src/southbridge/intel/i82801er/i82801er_lpc.c new file mode 100644 index 0000000000..c1ee7410ed --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_lpc.c @@ -0,0 +1,219 @@ +/* + * (C) 2003 Linux Networx, SuSE Linux AG + * (C) 2004 Tyan Computer + */ +#include +#include +#include +#include +#include +#include +#include +#include "i82801er.h" + +void isa_dma_init(void); /* from /pc80/isa-dma.c */ + +#define NMI_OFF 0 + +void i82801er_enable_ioapic( struct device *dev) +{ + uint32_t dword; + volatile uint32_t *ioapic_sba = (volatile uint32_t *)0xfec00000; + volatile uint32_t *ioapic_sbd = (volatile uint32_t *)0xfec00010; + + dword = pci_read_config32(dev, GEN_CNTL); + dword |= (3 << 7); /* enable ioapic */ + dword |= (1 <<13); /* coprocessor error enable */ + dword |= (1 << 1); /* delay transaction enable */ + dword |= (1 << 2); /* DMA collection buf enable */ + pci_write_config32(dev, GEN_CNTL, dword); + printk_debug("ioapic southbridge enabled %x\n",dword); + *ioapic_sba=0; + *ioapic_sbd=(2<<24); + //lyh *ioapic_sba=3; + //lyh *ioapic_sbd=1; + *ioapic_sba=0; + dword=*ioapic_sbd; + printk_debug("Southbridge apic id = %x\n",dword); + if(dword!=(2<<24)) + for(;;); + //lyh *ioapic_sba=3; + //lyh dword=*ioapic_sbd; + //lyh printk_debug("Southbridge apic DT = %x\n",dword); + //lyh if(dword!=1) + //lyh for(;;); + + +} +void i82801er_enable_serial_irqs( struct device *dev) +{ + pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(1 << 6)|((21 - 17) << 2)|(0<< 0)); +} +void i82801er_lpc_route_dma( struct device *dev, uint8_t mask) +{ + uint16_t word; + int i; + word = pci_read_config8(dev, PCI_DMA_CFG); + word &= ((1 << 10) - (1 << 8)); + for(i = 0; i < 8; i++) { + if (i == 4) + continue; + word |= ((mask & (1 << i))? 3:1) << (i*2); + } + pci_write_config16(dev, PCI_DMA_CFG, word); +} +void i82801er_rtc_init(struct device *dev) +{ + uint8_t byte; + uint32_t dword; + int rtc_failed; + byte = pci_read_config8(dev, GEN_PMCON_3); + rtc_failed = byte & RTC_FAILED; + if (rtc_failed) { + byte &= ~(1 << 1); /* preserve the power fail state */ + pci_write_config8(dev, GEN_PMCON_3, byte); + } + dword = pci_read_config32(dev, GEN_STS); + rtc_failed |= dword & (1 << 2); + rtc_init(rtc_failed); +} + + +void i82801er_1f0_misc(struct device *dev) +{ + pci_write_config16(dev, PCICMD, 0x014f); + pci_write_config32(dev, PMBASE, 0x00001001); + pci_write_config8(dev, ACPI_CNTL, 0x10); + pci_write_config32(dev, GPIO_BASE, 0x00001181); + pci_write_config8(dev, GPIO_CNTL, 0x10); + pci_write_config32(dev, PIRQA_ROUT, 0x0A05030B); + pci_write_config8(dev, PIRQE_ROUT, 0x07); + pci_write_config8(dev, RTC_CONF, 0x04); + pci_write_config8(dev, COM_DEC, 0x10); //lyh E0-> + pci_write_config16(dev, LPC_EN, 0x000F); //LYH 000D-> +} + +static void enable_hpet(struct device *dev) +{ + const unsigned long hpet_address = 0xfed0000; + + uint32_t dword; + uint32_t code = (0 & 0x3); + + dword = pci_read_config32(dev, GEN_CNTL); + dword |= (1 << 17); /* enable hpet */ + /*Bits [16:15]Memory Address Range + 00 FED0_0000h - FED0_03FFh + 01 FED0_1000h - FED0_13FFh + 10 FED0_2000h - FED0_23FFh + 11 FED0_3000h - FED0_33FFh*/ + + dword &= ~(3 << 15); /* clear it */ + dword |= (code<<15); + + printk_debug("enabling HPET @0x%x\n", hpet_address | (code <<12) ); +} + +static void lpc_init(struct device *dev) +{ + uint8_t byte; + int pwr_on=-1; + int nmi_option; + + /* IO APIC initialization */ + i82801er_enable_ioapic(dev); + + i82801er_enable_serial_irqs(dev); + + /* posted memory write enable */ + byte = pci_read_config8(dev, 0x46); + pci_write_config8(dev, 0x46, byte | (1<<0)); + + /* power after power fail */ + /* FIXME this doesn't work! */ + /* Which state do we want to goto after g3 (power restored)? + * 0 == S0 Full On + * 1 == S5 Soft Off + */ + pci_write_config8(dev, GEN_PMCON_3, pwr_on?0:1); + printk_info("set power %s after power fail\n", pwr_on?"on":"off"); +#if 0 + /* Enable Error reporting */ + /* Set up sync flood detected */ + byte = pci_read_config8(dev, 0x47); + byte |= (1 << 1); + pci_write_config8(dev, 0x47, byte); +#endif + + /* Set up NMI on errors */ + byte = pci_read_config8(dev, 0x61); + byte |= (1 << 3); /* IOCHK# NMI Enable */ + byte |= (1 << 6); /* PCI SERR# Enable */ + pci_write_config8(dev, 0x61, byte); + byte = pci_read_config8(dev, 0x70); + nmi_option = NMI_OFF; + get_option(&nmi_option, "nmi"); + if (nmi_option) { + byte |= (1 << 7); /* set NMI */ + pci_write_config8(dev, 0x70, byte); + } + + /* Initialize the real time clock */ + i82801er_rtc_init(dev); + + i82801er_lpc_route_dma(dev, 0xff); + + /* Initialize isa dma */ + isa_dma_init(); + + i82801er_1f0_misc(dev); + /* Initialize the High Precision Event Timers */ + enable_hpet(dev); +} + +static void i82801er_lpc_read_resources(device_t dev) +{ + unsigned int reg; + + /* Get the normal pci resources of this device */ + pci_dev_read_resources(dev); + + /* Find my place in the resource list */ + reg = dev->resources; + + /* Add an extra subtractive resource for both memory and I/O */ + dev->resource[reg].base = 0; + dev->resource[reg].size = 0; + dev->resource[reg].align = 0; + dev->resource[reg].gran = 0; + dev->resource[reg].limit = 0; + dev->resource[reg].flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED; + dev->resource[reg].index = 0; + reg++; + + dev->resource[reg].base = 0; + dev->resource[reg].size = 0; + dev->resource[reg].align = 0; + dev->resource[reg].gran = 0; + dev->resource[reg].limit = 0; + dev->resource[reg].flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE | IORESOURCE_ASSIGNED; + dev->resource[reg].index = 0; + reg++; + + dev->resources = reg; +} + +static struct device_operations lpc_ops = { + .read_resources = i82801er_lpc_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = lpc_init, + .scan_bus = scan_static_bus, + .enable = i82801er_enable, +}; + +static struct pci_driver lpc_driver __pci_driver = { + .ops = &lpc_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1F0, +}; diff --git a/src/southbridge/intel/i82801er/i82801er_nic.c b/src/southbridge/intel/i82801er/i82801er_nic.c new file mode 100644 index 0000000000..4815cf19e0 --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_nic.c @@ -0,0 +1,21 @@ +#include +#include +#include +#include +#include +#include "i82801er.h" + + +static struct device_operations nic_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = 0, + .scan_bus = 0, +}; + +static struct pci_driver nic_driver __pci_driver = { + .ops = &nic_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = 0x1051, +}; diff --git a/src/southbridge/intel/i82801er/i82801er_pci.c b/src/southbridge/intel/i82801er/i82801er_pci.c new file mode 100644 index 0000000000..201cedb1a9 --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_pci.c @@ -0,0 +1,33 @@ +#include +#include +#include +#include +#include +#include "i82801er.h" + +static void pci_init(struct device *dev) +{ + /* Enable pci error detecting */ + uint32_t dword; + /* System error enable */ + dword = pci_read_config32(dev, 0x04); + dword |= (1<<8); /* SERR# Enable */ + dword |= (1<<6); /* Parity Error Response */ + pci_write_config32(dev, 0x04, dword); + +} + +static struct device_operations pci_ops = { + .read_resources = pci_bus_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_bus_enable_resources, + .init = pci_init, + .scan_bus = pci_scan_bridge, +}; + +static struct pci_driver pci_driver __pci_driver = { + .ops = &pci_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1E0, +}; + diff --git a/src/southbridge/intel/i82801er/i82801er_reset.c b/src/southbridge/intel/i82801er/i82801er_reset.c new file mode 100644 index 0000000000..3d7a4b79b6 --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_reset.c @@ -0,0 +1,7 @@ +#include + +void hard_reset(void) +{ + /* Try rebooting through port 0xcf9 */ + outb((0 <<3)|(1<<2)|(1<<1), 0xcf9); +} diff --git a/src/southbridge/intel/i82801er/i82801er_sata.c b/src/southbridge/intel/i82801er/i82801er_sata.c new file mode 100644 index 0000000000..b00231e459 --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_sata.c @@ -0,0 +1,75 @@ +#include +#include +#include +#include +#include +#include "i82801er.h" + +static void sata_init(struct device *dev) +{ + + uint16_t word; + uint8_t byte; + int enable_c=1, enable_d=1; + int i; + + //Enable Serial ATA port + byte = pci_read_config8(dev,0x90); + byte &= 0xf8; + byte |= ICH5_SATA_ADDRESS_MAP & 7; + pci_write_config8(dev,0x90,byte); + +// for(i=0;i<10;i++) { + word = pci_read_config16(dev,0x92); + word &= 0xfffc; +// if( (word & 0x0003) == 0x0003) break; + word |= 0x0003; // enable P0/P1 + pci_write_config16(dev,0x92,word); +// } + +// for(i=0;i<10;i++) { + /* enable ide0 */ + word = pci_read_config16(dev, 0x40); + word &= ~(1 << 15); + if(enable_c==0) { +// if( (word & 0x8000) == 0x0000) break; + word |= 0x0000; + } + else { +// if( (word & 0x8000) == 0x8000) break; + word |= 0x8000; + } + pci_write_config16(dev, 0x40, word); +// } + /* enable ide1 */ +// for(i=0;i<10;i++) { + word = pci_read_config16(dev, 0x42); + word &= ~(1 << 15); + if(enable_d==0) { +// if( (word & 0x8000) == 0x0000) break; + word |= 0x0000; + } + else { +// if( (word & 0x8000) == 0x8000) break; + word |= 0x8000; + } + pci_write_config16(dev, 0x42, word); +// } + +} + +static struct device_operations sata_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = sata_init, + .scan_bus = 0, + .enable = i82801er_enable, +}; + +static struct pci_driver stat_driver __pci_driver = { + .ops = &sata_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1F2_R, +}; + diff --git a/src/southbridge/intel/i82801er/i82801er_smbus.c b/src/southbridge/intel/i82801er/i82801er_smbus.c new file mode 100644 index 0000000000..fd06871234 --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_smbus.c @@ -0,0 +1,92 @@ +#include +#include +#include + +#define PM_BUS 0 +#define PM_DEVFN PCI_DEVFN(0x1f,3) + +#define SMBUS_IO_BASE 0x1000 +#define SMBHSTSTAT 0 +#define SMBHSTCTL 2 +#define SMBHSTCMD 3 +#define SMBHSTADD 4 +#define SMBHSTDAT0 5 +#define SMBHSTDAT1 6 +#define SMBBLKDAT 7 + +void smbus_enable(void) +{ + unsigned char byte; + /* iobase addr */ + pcibios_write_config_dword(PM_BUS, PM_DEVFN, 0x20, SMBUS_IO_BASE | 1); + /* smbus enable */ + pcibios_write_config_byte(PM_BUS, PM_DEVFN, 0x40, 1); + /* iospace enable */ + pcibios_write_config_word(PM_BUS, PM_DEVFN, 0x4, 1); + + /* Disable interrupt generation */ + outb(0, SMBUS_IO_BASE + SMBHSTCTL); + +} + +void smbus_setup(void) +{ + outb(0, SMBUS_IO_BASE + SMBHSTSTAT); +} + +static void smbus_wait_until_ready(void) +{ + while((inb(SMBUS_IO_BASE + SMBHSTSTAT) & 1) == 1) { + /* nop */ + } +} + +static void smbus_wait_until_done(void) +{ + unsigned char byte; + do { + byte = inb(SMBUS_IO_BASE + SMBHSTSTAT); + } + while((byte &1) == 1); + while( (byte & ~1) == 0) { + byte = inb(SMBUS_IO_BASE + SMBHSTSTAT); + } +} + +int smbus_read_byte(unsigned device, unsigned address, unsigned char *result) +{ + unsigned char host_status_register; + unsigned char byte; + + smbus_wait_until_ready(); + + /* setup transaction */ + /* disable interrupts */ + outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & (~1), SMBUS_IO_BASE + SMBHSTCTL); + /* set the device I'm talking too */ + outb(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBHSTADD); + /* set the command/address... */ + outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD); + /* set up for a byte data read */ + outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xE3) | (0x2 << 2), SMBUS_IO_BASE + SMBHSTCTL); + + /* clear any lingering errors, so the transaction will run */ + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT); + + /* clear the data byte...*/ + outb(0, SMBUS_IO_BASE + SMBHSTDAT0); + + /* start the command */ + outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), SMBUS_IO_BASE + SMBHSTCTL); + + /* poll for transaction completion */ + smbus_wait_until_done(); + + host_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT); + + /* read results of transaction */ + byte = inb(SMBUS_IO_BASE + SMBHSTDAT0); + + *result = byte; + return host_status_register != 0x02; +} diff --git a/src/southbridge/intel/i82801er/i82801er_usb.c b/src/southbridge/intel/i82801er/i82801er_usb.c new file mode 100644 index 0000000000..49c6263add --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_usb.c @@ -0,0 +1,54 @@ +#include +#include +#include +#include +#include +#include "i82801er.h" + +static void usb_init(struct device *dev) +{ + uint32_t cmd; + +#if 0 + printk_debug("USB: Setting up controller.. "); + cmd = pci_read_config32(dev, PCI_COMMAND); + pci_write_config32(dev, PCI_COMMAND, + cmd | PCI_COMMAND_IO | PCI_COMMAND_MEMORY | + PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE); + + + printk_debug("done.\n"); +#endif + +} + +static struct device_operations usb_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = usb_init, + .scan_bus = 0, + .enable = i82801er_enable, +}; + +static struct pci_driver usb_driver_1 __pci_driver = { + .ops = &usb_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1D0, +}; +static struct pci_driver usb_driver_2 __pci_driver = { + .ops = &usb_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1D1, +}; +static struct pci_driver usb_driver_3 __pci_driver = { + .ops = &usb_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1D2, +}; +static struct pci_driver usb_driver_4 __pci_driver = { + .ops = &usb_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1D3, +}; + diff --git a/src/southbridge/intel/i82801er/i82801er_usb2.c b/src/southbridge/intel/i82801er/i82801er_usb2.c new file mode 100644 index 0000000000..551d4ed3e0 --- /dev/null +++ b/src/southbridge/intel/i82801er/i82801er_usb2.c @@ -0,0 +1,39 @@ +//2003 Copywright Tyan + +#include +#include +#include +#include +#include +#include "i82801er.h" + +static void usb2_init(struct device *dev) +{ + uint32_t cmd; + +#if 0 + printk_debug("USB: Setting up controller.. "); + cmd = pci_read_config32(dev, PCI_COMMAND); + pci_write_config32(dev, PCI_COMMAND, + cmd | PCI_COMMAND_IO | PCI_COMMAND_MEMORY | + PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE); + + + printk_debug("done.\n"); +#endif +} + +static struct device_operations usb2_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = usb2_init, + .scan_bus = 0, + .enable = i82801er_enable, +}; + +static struct pci_driver usb2_driver __pci_driver = { + .ops = &usb2_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82801ER_1D7, +}; diff --git a/src/southbridge/intel/i82870/82870.h b/src/southbridge/intel/i82870/82870.h new file mode 100644 index 0000000000..f9289d4027 --- /dev/null +++ b/src/southbridge/intel/i82870/82870.h @@ -0,0 +1,10 @@ +/* for io apic 1461 */ +#define PCICMD 0x04 +#define SUBSYS 0x2c +#define MBAR 0x10 +#define ABAR 0x40 + +/* for pci bridge 1460 */ +#define MTT 0x042 +#define HCCR 0x0f0 +#define ACNF 0x0e0 diff --git a/src/southbridge/intel/i82870/Config.lb b/src/southbridge/intel/i82870/Config.lb new file mode 100644 index 0000000000..e6a96517f0 --- /dev/null +++ b/src/southbridge/intel/i82870/Config.lb @@ -0,0 +1,3 @@ +driver p64h2_ioapic.o +driver p64h2_pcibridge.o +#driver p64h2_pci_parity.o diff --git a/src/southbridge/intel/i82870/p64h2_ioapic.c b/src/southbridge/intel/i82870/p64h2_ioapic.c new file mode 100644 index 0000000000..e2bb33883d --- /dev/null +++ b/src/southbridge/intel/i82870/p64h2_ioapic.c @@ -0,0 +1,89 @@ +#include +#include +#include +#include +#include +#include +#include "82870.h" + +static int ioapic_no = 0; + +static void p64h2_ioapic_enable(device_t dev) +{ + uint32_t dword; + uint16_t word; + + /* We have to enable MEM and Bus Master for IOAPIC */ + word = 0x0146; + pci_write_config16(dev, PCICMD, word); + dword = 0x358015d9; + pci_write_config32(dev, SUBSYS, dword); + + +} + +static void p64h2_ioapic_init(device_t dev) +{ + uint32_t dword; + uint16_t word; + int i, addr; + + volatile uint32_t *ioapic_a; /* io apic io memory space command address */ + volatile uint32_t *ioapic_d; /* io apic io memory space data address */ + + i = ioapic_no++; + + if(i<3) /* io apic address numbers are 3,4,5,&8 */ + addr=i+3; + else + addr=i+5; + /* Read the MBAR address for setting up the io apic in io memory space */ + dword = pci_read_config32(dev, PCI_BASE_ADDRESS_0); + ioapic_a = (uint32_t *) dword; + ioapic_d = ioapic_a +0x04; + printk_debug("IOAPIC %d at %02x:%02x.%01x MBAR = %x DataAddr = %x\n", + addr, dev->bus->secondary, + PCI_SLOT(dev->path.u.pci.devfn), PCI_FUNC(dev->path.u.pci.devfn), + ioapic_a, ioapic_d); + +#if 0 + dword = (u32)ioapic_a; + word = 0x8000 + ((dword >>8)&0x0fff); + pci_write_config_word(dev, ABAR, word); +#endif + /* Set up the io apic for the p64h2 - 1461 */ + *ioapic_a=0; + *ioapic_d=(addr<<24); /* Set the address number */ + *ioapic_a=3; + *ioapic_d=1; /* Enable the io apic */ + + /* This code test the setup to see if we really found the io apic */ + *ioapic_a=0; + dword=*ioapic_d; + printk_debug("PCI %d apic id = %x\n",addr,dword); + if(dword!=(addr<<24)) + for(;;); + *ioapic_a=3; + dword=*ioapic_d; + printk_debug("PCI %d apic DT = %x\n",addr,dword); + if(dword!=1) + for(;;); + + +} + +static struct device_operations ioapic_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = p64h2_ioapic_init, + .scan_bus = 0, + .enable = p64h2_ioapic_enable, +}; + +static struct pci_driver ioapic_driver __pci_driver = { + .ops = &ioapic_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82870_1E0, + +}; diff --git a/src/southbridge/intel/i82870/p64h2_pci_parity.c b/src/southbridge/intel/i82870/p64h2_pci_parity.c new file mode 100644 index 0000000000..d80f9213c9 --- /dev/null +++ b/src/southbridge/intel/i82870/p64h2_pci_parity.c @@ -0,0 +1,26 @@ +#include +#include +#include +#include +# + +void p64h2_pci_parity_enable(void) +{ + uint8_t reg; + + /* 2SERREN - SERR enable for PCI bridge secondary device */ + /* 2PEREN - Parity error for PCI bridge secondary device */ + pcibios_read_config_byte(1, ((29 << 3) + (0 << 0)), 0x3e, ®); + reg |= ((1 << 1) + (1 << 0)); + pcibios_write_config_byte(1, ((29 << 3) + (0 << 0)), 0x3e, reg); + + /* 2SERREN - SERR enable for PCI bridge secondary device */ + /* 2PEREN - Parity error for PCI bridge secondary device */ + pcibios_read_config_byte(1, ((31 << 3) + (0 << 0)), 0x3e, ®); + reg |= ((1 << 1) + (1 << 0)); + pcibios_write_config_byte(1, ((31 << 3) + (0 << 0)), 0x3e, reg); + + return; +} + + diff --git a/src/southbridge/intel/i82870/p64h2_pcibridge.c b/src/southbridge/intel/i82870/p64h2_pcibridge.c new file mode 100644 index 0000000000..6f161e900b --- /dev/null +++ b/src/southbridge/intel/i82870/p64h2_pcibridge.c @@ -0,0 +1,39 @@ +#include +#include +#include +#include +#include +#include +#include "82870.h" + +static void p64h2_pcix_init(device_t dev) +{ + uint32_t dword; + uint16_t word; + uint8_t byte; + + + /* The purpose of changes to HCCR, ACNF, and MTT is to speed up the + PCI bus for cards having high speed transfers. */ + dword = 0xc2040002; + pci_write_config32(dev, HCCR, dword); + dword = 0x0000c3bf; + pci_write_config32(dev, ACNF, dword); + byte = 0x08; + pci_write_config8(dev, MTT, byte); + +} +static struct device_operations pcix_ops = { + .read_resources = pci_bus_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_bus_enable_resources, + .init = p64h2_pcix_init, + .scan_bus = pci_scan_bridge, +}; + +static struct pci_driver pcix_driver __pci_driver = { + .ops = &pcix_ops, + .vendor = PCI_VENDOR_ID_INTEL, + .device = PCI_DEVICE_ID_INTEL_82870_1F0, +}; + diff --git a/src/superio/winbond/w83627hf/superio.c b/src/superio/winbond/w83627hf/superio.c index 04a6e2a7e8..ee0a6872e3 100644 --- a/src/superio/winbond/w83627hf/superio.c +++ b/src/superio/winbond/w83627hf/superio.c @@ -16,13 +16,100 @@ #include "chip.h" #include "w83627hf.h" -static void init(device_t dev) + +void pnp_enter_ext_func_mode(device_t dev) { + outb(0x87, dev->path.u.pnp.port); + outb(0x87, dev->path.u.pnp.port); +} +void pnp_exit_ext_func_mode(device_t dev) { + outb(0xaa, dev->path.u.pnp.port); +} + +void pnp_write_hwm(unsigned long port_base, uint8_t reg, uint8_t value) +{ + outb(reg, port_base+5); + outb(value, port_base+6); +} + +uint8_t pnp_read_hwm(unsigned long port_base, uint8_t reg) +{ + outb(reg, port_base + 5); + return inb(port_base + 6); +} + +static void enable_hwm_smbus(device_t dev) { + uint8_t reg, value; + reg = 0x2b; + value = pnp_read_config(dev, reg); + value &= 0x3f; + pnp_write_config(dev, reg, value); +} + +#if 0 +static void dump_pnp_device(device_t dev) +{ + int i; + print_debug("\r\n"); + + for(i = 0; i <= 255; i++) { + uint8_t reg, val; + if ((i & 0x0f) == 0) { + print_debug_hex8(i); + print_debug_char(':'); + } + reg = i; + if(i!=0xaa) { + val = pnp_read_config(dev, reg); + } + else { + val = 0xaa; + } + print_debug_char(' '); + print_debug_hex8(val); + if ((i & 0x0f) == 0x0f) { + print_debug("\r\n"); + } + } +} +#endif + +static void init_hwm(unsigned long base) +{ + uint8_t reg, value; + int i; + + unsigned hwm_reg_values[] = { +// reg mask data + 0x40 , 0xff , 0x81, // ; Start Hardware Monitoring for WIN627 + 0x48 , 0xaa , 0x2a, // ; Program SIO SMBus BAR to 54h>>1 +// 0x48 , 0xc8 , 0x48, // ; Program SIO SMBus BAR to 90h>>1 + 0x4A , 0x21 , 0x21, // ; Program T2 SMBus BAR to 92h>>1 & + // ; Program T3 SMBus BAR to 94h>>1 + 0x4E , 0x80 , 0x00, + 0x43 , 0x00 , 0xFF, + 0x44 , 0x00 , 0x3F, + 0x4C , 0xBF , 0x18, + 0x4D , 0xFF , 0x80 // ; Turn Off Beep + + }; + + for(i = 0; i< sizeof(hwm_reg_values)/sizeof(hwm_reg_values[0]); i+=3 ) { + reg = hwm_reg_values[i]; + value = pnp_read_hwm(base, reg); + value &= 0xff & hwm_reg_values[i+1]; + value |= 0xff & hwm_reg_values[i+2]; +#if 0 + printk_debug("base = 0x%04x, reg = 0x%02x, value = 0x%02x\r\n", base,reg,value); +#endif + pnp_write_hwm(base,reg, value); + } +} + + +static void w83627hf_init(device_t dev) { struct superio_winbond_w83627hf_config *conf; struct resource *res0, *res1; - /* Wishlist handle well known programming interfaces more - * generically. - */ if (!dev->enabled) { return; } @@ -41,15 +128,70 @@ static void init(device_t dev) res1 = get_resource(dev, PNP_IDX_IO1); init_pc_keyboard(res0->base, res1->base, &conf->keyboard); break; + case W83627HF_HWM: + res0 = get_resource(dev, PNP_IDX_IO0); + init_hwm(res0->base); + break; } + +} + +void w83627hf_pnp_set_resources(device_t dev) +{ + + pnp_enter_ext_func_mode(dev); + + pnp_set_resources(dev); + +#if 0 + dump_pnp_device(dev); +#endif + + pnp_exit_ext_func_mode(dev); + +} + +void w83627hf_pnp_enable_resources(device_t dev) +{ + pnp_enter_ext_func_mode(dev); + + pnp_enable_resources(dev); + + switch(dev->path.u.pnp.device) { + case W83627HF_HWM: + //set the pin 91,92 as I2C bus + printk_debug("w83627hf hwm smbus enabled\r\n"); + enable_hwm_smbus(dev); + break; + } + +#if 0 + dump_pnp_device(dev); +#endif + + pnp_exit_ext_func_mode(dev); + +} + +void w83627hf_pnp_enable(device_t dev) +{ + + if (!dev->enabled) { + pnp_enter_ext_func_mode(dev); + + pnp_set_logical_device(dev); + pnp_set_enable(dev, 0); + + pnp_exit_ext_func_mode(dev); + } } static struct device_operations ops = { .read_resources = pnp_read_resources, - .set_resources = pnp_set_resources, - .enable_resources = pnp_enable_resources, - .enable = pnp_enable, - .init = init, + .set_resources = w83627hf_pnp_set_resources, + .enable_resources = w83627hf_pnp_enable_resources, + .enable = w83627hf_pnp_enable, + .init = w83627hf_init, }; static struct pnp_info pnp_dev_info[] = { @@ -61,8 +203,8 @@ static struct pnp_info pnp_dev_info[] = { { &ops, W83627HF_KBC, PNP_IO0 | PNP_IO1 | PNP_IRQ0 | PNP_IRQ1, { 0x7ff, 0 }, { 0x7ff, 0x4}, }, { &ops, W83627HF_CIR, PNP_IO0 | PNP_IRQ0, { 0x7f8, 0 }, }, { &ops, W83627HF_GAME_MIDI_GPIO1, PNP_IO0 | PNP_IO1 | PNP_IRQ0, { 0x7ff, 0 }, {0x7fe, 4} }, - { &ops, W83627HF_GPIO2, PNP_IO0 | PNP_IO1 | PNP_IRQ0, { 0x7ff, 0 }, {0x7fe, 4} }, - { &ops, W83627HF_GPIO3, PNP_IO0 | PNP_IO1 | PNP_IRQ0, { 0x7ff, 0 }, {0x7fe, 4} }, + { &ops, W83627HF_GPIO2,}, + { &ops, W83627HF_GPIO3,}, { &ops, W83627HF_ACPI, PNP_IRQ0, }, { &ops, W83627HF_HWM, PNP_IO0 | PNP_IRQ0, { 0xff8, 0 } }, }; @@ -77,3 +219,4 @@ struct chip_control superio_winbond_w83627hf_control = { .enumerate = enumerate, .name = "Winbond w83627hf" }; + diff --git a/targets/tyan/s2735/Config.lb b/targets/tyan/s2735/Config.lb new file mode 100644 index 0000000000..7a3faf4f9c --- /dev/null +++ b/targets/tyan/s2735/Config.lb @@ -0,0 +1,265 @@ +# Sample config file for +# the Tyan s2735 +# This will make a target directory of ./s2735 + +loadoptions + +target s2735 + +uses ARCH +uses CONFIG_COMPRESS +uses CONFIG_IOAPIC +uses CONFIG_ROM_STREAM +uses CONFIG_ROM_STREAM_START +uses CONFIG_SMP +uses CONFIG_UDELAY_TSC +uses CPU_FIXUP +uses FALLBACK_SIZE +uses HAVE_FALLBACK_BOOT +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses i586 +uses i686 +uses INTEL_PPRO_MTRR +uses HEAP_SIZE +uses IRQ_SLOT_COUNT +uses MAINBOARD +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +#uses MEMORY_HOLE +uses PAYLOAD_SIZE +uses _RAMBASE +uses _ROMBASE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_OFFSET +uses ROM_SECTION_SIZE +uses ROM_SIZE +uses STACK_SIZE +uses USE_FALLBACK_IMAGE +uses USE_OPTION_TABLE +uses HAVE_OPTION_TABLE +uses CONFIG_CHIP_CONFIGURE + +uses CONFIG_CONSOLE_BTEXT +uses CONFIG_CONSOLE_SERIAL8250 +uses TTYS0_BAUD +#SMDC Support +#uses CONFIG_CONSOLE_SERIAL8250_2 +#uses TTYS1_BAUD +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses DEBUG +uses CONFIG_MAX_CPUS +uses CONFIG_LOGICAL_CPUS +uses CONFIG_MAX_PHYSICAL_CPUS +uses LINUXBIOS_EXTRA_VERSION +uses XIP_ROM_SIZE +uses XIP_ROM_BASE + +uses CONFIG_FS_STREAM +uses CONFIG_IDE + +uses HAVE_HARD_RESET + +#uses CONFIG_VGABIOS +#uses CONFIG_REALMODE_IDT +#uses CONFIG_PCIBIOS +#uses VGABIOS_START +#uses SCSIFW_START + +# +#uses CONFIG_LSI_SCSI_FW_FIXUP + +option HAVE_OPTION_TABLE=1 +option HAVE_MP_TABLE=1 +option CPU_FIXUP=1 +option CONFIG_UDELAY_TSC=0 +option i686=1 +option i586=1 +option INTEL_PPRO_MTRR=1 +#option ROM_SIZE=524288 +option ROM_SIZE=1048576 + +option HAVE_HARD_RESET=1 + +#option CONFIG_CONSOLE_BTEXT=1 +#option CONFIG_VGABIOS=1 +#option CONFIG_REALMODE_IDT=1 +#option CONFIG_PCIBIOS=1 +#option VGABIOS_START=0xfff8c000 +#option SCSIFW_START=0xfff80000 + +#option CONFIG_FS_STREAM=1 +#option CONFIG_IDE=1 + +option HAVE_FALLBACK_BOOT=1 + +# use the new chip configure code. + +option CONFIG_CHIP_CONFIGURE=1 +#option CONFIG_LSI_SCSI_FW_FIXUP=1 + + +# +### +### Build code to export a programmable irq routing table +### +option HAVE_PIRQ_TABLE=1 +option IRQ_SLOT_COUNT=15 +# +### +### Build code for SMP support +### Only worry about 2 micro processors +### +option CONFIG_SMP=1 +option CONFIG_MAX_CPUS=4 +option CONFIG_LOGICAL_CPUS=1 +option CONFIG_MAX_PHYSICAL_CPUS=2 +# +### +### Build code to setup a generic IOAPIC +### +option CONFIG_IOAPIC=1 +# +### +### MEMORY_HOLE instructs earlymtrr.inc to +### enable caching from 0-640KB and to disable +### caching from 640KB-1MB using fixed MTRRs +### +### Enabling this option breaks SMP because secondary +### CPU identification depends on only variable MTRRs +### being enabled. +### +#option MEMORY_HOLE=0 +# +### +### Clean up the motherboard id strings +### +option MAINBOARD_PART_NUMBER="S2735" +option MAINBOARD_VENDOR="Tyan" +### +### Compute the location and size of where this firmware image +### (linuxBIOS plus bootloader) will live in the boot rom chip. +### +#option FALLBACK_SIZE=524288 +#option FALLBACK_SIZE=98304 +option FALLBACK_SIZE=131072 + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +option ROM_IMAGE_SIZE=65536 + + +### +### Compute where this copy of linuxBIOS will start in the boot rom +### +# +### + +## We do use compressed image +option CONFIG_COMPRESS=1 + +option CONFIG_CONSOLE_SERIAL8250=1 +option TTYS0_BAUD=115200 + +#SMDC support +#option CONFIG_CONSOLE_SERIAL8250_2=1 +#option TTYS1_BAUD=19200 + + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +option DEFAULT_CONSOLE_LOGLEVEL=8 +## At a maximum only compile in this level of debugging +option MAXIMUM_CONSOLE_LOGLEVEL=8 + +option DEBUG=1 + +# + +## LinuxBIOS C code runs at this location in RAM +option _RAMBASE=0x004000 + +## +## Use a 32K stack +## +option STACK_SIZE=0x8000 + +## +## Use a 56K heap +## +option HEAP_SIZE=0xe000 + +# +### +### Compute the start location and size size of +### The linuxBIOS bootloader. +### +option CONFIG_ROM_STREAM = 1 + +# +# +romimage "normal" +# 48K for SCSI FW +# option ROM_SIZE = 475136 +# 48K for SCSI FW and 48K for ATI ROM +# option ROM_SIZE = 425984 +# 64K for Etherboot +# option ROM_SIZE = 458752 + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal" + option USE_FALLBACK_IMAGE=0 + option ROM_SECTION_SIZE = (ROM_SIZE - FALLBACK_SIZE) + option ROM_SECTION_OFFSET= 0 + + option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE) + option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) + option _ROMBASE = (CONFIG_ROM_STREAM_START + PAYLOAD_SIZE) + +# option XIP_ROM_SIZE = FALLBACK_SIZE + option XIP_ROM_SIZE = 65536 + option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE) + + mainboard tyan/s2735 +# payload ../../../payloads/e1000--ide_disk.zelf +# payload ../../../payloads/filo.elf +# payload ../../../payloads/filo_mem.elf +# payload ../../../payloads/filo_mem_btext.elf +# payload ../../../payloads/filo_btext.zelf + payload ../../../payloads/e1000--filo_btext.zelf +end + +romimage "fallback" + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback" + option USE_FALLBACK_IMAGE=1 + option ROM_SECTION_SIZE = FALLBACK_SIZE + option ROM_SECTION_OFFSET= (ROM_SIZE - FALLBACK_SIZE) + + option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE) + option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) + option _ROMBASE = (CONFIG_ROM_STREAM_START + PAYLOAD_SIZE) + +# option XIP_ROM_SIZE = FALLBACK_SIZE + option XIP_ROM_SIZE = 65536 + option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE) + + mainboard tyan/s2735 +# payload ../../../payloads/e1000--ide_disk.zelf +# payload ../../../payloads/filo_mem.elf +# payload ../../../payloads/filo_mem_btext.elf +# payload ../../../payloads/e1000_btext.zelf + payload ../../../payloads/e1000--filo_btext.zelf + +end + +buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback" diff --git a/targets/tyan/s2735/VERSION b/targets/tyan/s2735/VERSION new file mode 100644 index 0000000000..cd5ac039d6 --- /dev/null +++ b/targets/tyan/s2735/VERSION @@ -0,0 +1 @@ +2.0 diff --git a/targets/tyan/s2735/ns2735 b/targets/tyan/s2735/ns2735 new file mode 100644 index 0000000000..f983eb4033 --- /dev/null +++ b/targets/tyan/s2735/ns2735 @@ -0,0 +1,8 @@ +#!/bin/bash +TYANMB=s27i35 +cd "$TYANMB" +make +#cat ../fwx.rom ../atix.rom ./normal/linuxbios.rom ./fallback/linuxbios.rom > $TYANMB"_linuxbios.rom" +#cat ../fwx.rom ./normal/linuxbios.rom ./fallback/linuxbios.rom > $TYANMB"_linuxbios.rom" +cat ./normal/linuxbios.rom ./fallback/linuxbios.rom > $TYANMB"_linuxbios.rom" +cp -f $TYANMB"_linuxbios.rom" /home/yhlu/