mb/google/zork: Add support for active low wifi power enable

A late change went into v3+ of reference schematics which inverted
EN_PWR_WIFI to meet PCIe reset/power timings for WiFi device. This is
incorporated into v3.51+ for Trembyle reference and v3.2+ for Dalboz
reference. However, some variants are built with v3+ reference
schematics, but without the inversion of EN_PWR_WIFI polarity. Thus,
we need to add support for following combinations:
1. Pre-v3 Schematics
2. V3+ Schematics
3. V3+ Schematics + Active low wifi power

This change adds a new Kconfig
`VARIANT_MIN_BOARD_ID_WIFI_POWER_ACTIVE_LOW` that sets the minimum
board ID that has EN_PWR_WIFI active low in hardware. Variants that
missed this change in V3+ integration (berknip and vilboz) have board
IDs set to VARIANT_MIN_BOARD_ID_V3_SCHEMATICS + 1. For others, this
defaults to VARIANT_MIN_BOARD_ID_V3_SCHEMATICS.

BUG=b:159749536

Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib8da7fba5f4a518a51b203d6a01a9551e261d8b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>

src/mainboard/google/zork/Kconfig

@@ -141,5 +141,12 @@ config VARIANT_MIN_BOARD_ID_V3_SCHEMATICS
 	default 2 if BOARD_GOOGLE_BERKNIP
 	default 3 if BOARD_GOOGLE_DALBOZ
 	default 2 if BOARD_GOOGLE_VILBOZ
+	default 256
+
+config VARIANT_MIN_BOARD_ID_WIFI_POWER_ACTIVE_LOW
+	int
+	default 3 if BOARD_GOOGLE_BERKNIP
+	default 3 if BOARD_GOOGLE_VILBOZ
+	default VARIANT_MIN_BOARD_ID_V3_SCHEMATICS
 
 endif # BOARD_GOOGLE_BASEBOARD_TREMBYLE || BOARD_GOOGLE_BASEBOARD_DALBOZ

src/mainboard/google/zork/variants/baseboard/gpio_baseboard_dalboz.c

@@ -217,20 +217,20 @@ const __weak struct sci_source *get_gpe_table(size_t *num)
 	return NULL;
 }
 
-static void wifi_power_reset_configure_v3(void)
+static void wifi_power_reset_configure_active_low_power(void)
 {
 	/*
 	 * Configure WiFi GPIOs such that:
 	 * - WIFI_AUX_RESET is configured first to assert PERST# to WiFi device.
-	 * - Enable power to WiFi using EN_PWR_WIFI.
+	 * - Enable power to WiFi using EN_PWR_WIFI_L.
 	 * - Wait for 50ms after power to WiFi is enabled.
-	 * - Deassert PERST# to WiFi device by driving WIFI_AUX_RESET low.
+	 * - Deassert WIFI_AUX_RESET.
 	 */
 	static const struct soc_amd_gpio v3_wifi_table[] = {
 		/* WIFI_AUX_RESET */
 		PAD_GPO(GPIO_29, HIGH),
-		/* EN_PWR_WIFI */
+		/* EN_PWR_WIFI_L */
-		PAD_GPO(GPIO_42, HIGH),
+		PAD_GPO(GPIO_42, LOW),
 	};
 	program_gpios(v3_wifi_table, ARRAY_SIZE(v3_wifi_table));
 
@@ -238,6 +238,41 @@ static void wifi_power_reset_configure_v3(void)
 	gpio_set(GPIO_29, 0);
 }
 
+static void wifi_power_reset_configure_active_high_power(void)
+{
+	/*
+	 * When GPIO_42 is configured as active high for enabling WiFi power, WIFI_AUX_RESET
+	 * gets pulled high because of external PU to PP3300_WIFI. Thus, EN_PWR_WIFI needs to be
+	 * set low before driving it high to trigger a WiFi power cycle to meet PCIe
+	 * requirements. Thus, configure GPIOs such that:
+	 * - WIFI_AUX_RESET is configured first to assert PERST# to WiFi device
+	 * - Disable power to WiFi.
+	 * - Wait 10ms for WiFi power to go low.
+	 * - Enable power to WiFi using EN_PWR_WIFI.
+	 * - Deassert WIFI_AUX_RESET.
+	 */
+	static const struct soc_amd_gpio v3_wifi_table[] = {
+		/* WIFI_AUX_RESET */
+		PAD_GPO(GPIO_29, HIGH),
+		/* EN_PWR_WIFI */
+		PAD_GPO(GPIO_42, LOW),
+	};
+	program_gpios(v3_wifi_table, ARRAY_SIZE(v3_wifi_table));
+
+	mdelay(10);
+	gpio_set(GPIO_42, 1);
+	mdelay(50);
+	gpio_set(GPIO_29, 0);
+}
+
+static void wifi_power_reset_configure_v3(uint32_t board_version)
+{
+	if (board_version >= CONFIG_VARIANT_MIN_BOARD_ID_WIFI_POWER_ACTIVE_LOW)
+		wifi_power_reset_configure_active_low_power();
+	else
+		wifi_power_reset_configure_active_high_power();
+}
+
 static void wifi_power_reset_configure_pre_v3(void)
 {
 	/*
@@ -273,7 +308,7 @@ __weak void variant_pcie_power_reset_configure(void)
 
 	if (!google_chromeec_cbi_get_board_version(&board_version) &&
 	    (board_version >= CONFIG_VARIANT_MIN_BOARD_ID_V3_SCHEMATICS))
-		wifi_power_reset_configure_v3();
+		wifi_power_reset_configure_v3(board_version);
 	else
 		wifi_power_reset_configure_pre_v3();
 }
@@ -283,6 +318,12 @@ static const struct soc_amd_gpio gpio_sleep_table[] = {
 	PAD_GPO(GPIO_5, LOW),
 	/* PCIE_RST1_L */
 	PAD_GPO(GPIO_27, LOW),
+	/*
+	 * On pre-v3 schematics, GPIO_29 is EN_PWR_WIFI. So, setting to high should be no-op.
+	 * On v3+ schematics, GPIO_29 is WIFI_AUX_RESET. Setting to high ensures that PERST# is
+	 * asserted to WiFi device until coreboot reconfigures GPIO_29 on resume path.
+	 */
+	PAD_GPO(GPIO_29, HIGH),
 	/* NVME_AUX_RESET_L */
 	PAD_GPO(GPIO_40, LOW),
 	/* EN_PWR_CAMERA */

src/mainboard/google/zork/variants/baseboard/gpio_baseboard_trembyle.c

@@ -211,20 +211,20 @@ const __weak struct sci_source *get_gpe_table(size_t *num)
 	return NULL;
 }
 
-static void wifi_power_reset_configure_v3(void)
+static void wifi_power_reset_configure_active_low_power(void)
 {
 	/*
 	 * Configure WiFi GPIOs such that:
 	 * - WIFI_AUX_RESET_L is configured first to assert PERST# to WiFi device.
-	 * - Enable power to WiFi using EN_PWR_WIFI.
+	 * - Enable power to WiFi using EN_PWR_WIFI_L.
 	 * - Wait for 50ms after power to WiFi is enabled.
 	 * - Deassert WIFI_AUX_RESET_L.
 	 */
 	static const struct soc_amd_gpio v3_wifi_table[] = {
 		/* WIFI_AUX_RESET_L */
 		PAD_GPO(GPIO_86, LOW),
-		/* EN_PWR_WIFI */
+		/* EN_PWR_WIFI_L */
-		PAD_GPO(GPIO_42, HIGH),
+		PAD_GPO(GPIO_42, LOW),
 	};
 	program_gpios(v3_wifi_table, ARRAY_SIZE(v3_wifi_table));
 
@@ -232,6 +232,41 @@ static void wifi_power_reset_configure_v3(void)
 	gpio_set(GPIO_86, 1);
 }
 
+static void wifi_power_reset_configure_active_high_power(void)
+{
+	/*
+	 * When GPIO_42 is configured as active high for enabling WiFi power, WIFI_AUX_RESET_L
+	 * gets pulled high because of external PU to PP3300_WIFI. Thus, EN_PWR_WIFI needs to be
+	 * set low before driving it high to trigger a WiFi power cycle to meet PCIe
+	 * requirements. Thus, configura GPIOs such that:
+	 * - WIFI_AUX_RESET_L is configured first to assert PERST# to WiFi device
+	 * - Disable power to WiFi.
+	 * - Wait 10ms for WiFi power to go low.
+	 * - Enable power to WiFi using EN_PWR_WIFI.
+	 * - Deassert WIFI_AUX_RESET_L.
+	 */
+	static const struct soc_amd_gpio v3_wifi_table[] = {
+		/* WIFI_AUX_RESET_L */
+		PAD_GPO(GPIO_86, LOW),
+		/* EN_PWR_WIFI */
+		PAD_GPO(GPIO_42, LOW),
+	};
+	program_gpios(v3_wifi_table, ARRAY_SIZE(v3_wifi_table));
+
+	mdelay(10);
+	gpio_set(GPIO_42, 1);
+	mdelay(50);
+	gpio_set(GPIO_86, 1);
+}
+
+static void wifi_power_reset_configure_v3(uint32_t board_version)
+{
+	if (board_version >= CONFIG_VARIANT_MIN_BOARD_ID_WIFI_POWER_ACTIVE_LOW)
+		wifi_power_reset_configure_active_low_power();
+	else
+		wifi_power_reset_configure_active_high_power();
+}
+
 static void wifi_power_reset_configure_pre_v3(void)
 {
 	/*
@@ -264,7 +299,7 @@ __weak void variant_pcie_power_reset_configure(void)
 
 	if (!google_chromeec_cbi_get_board_version(&board_version) &&
 	    (board_version >= CONFIG_VARIANT_MIN_BOARD_ID_V3_SCHEMATICS))
-		wifi_power_reset_configure_v3();
+		wifi_power_reset_configure_v3(board_version);
 	else
 		wifi_power_reset_configure_pre_v3();
 }