diff --git a/src/mainboard/google/brya/Kconfig b/src/mainboard/google/brya/Kconfig
index b14178ce56..a658ce2c81 100644
--- a/src/mainboard/google/brya/Kconfig
+++ b/src/mainboard/google/brya/Kconfig
@@ -79,7 +79,8 @@ config DRIVER_TPM_I2C_BUS
 	default 0x3 if BOARD_GOOGLE_PRIMUS4ES
 	default 0x1 if BOARD_GOOGLE_GIMBLE
 	default 0x3 if BOARD_GOOGLE_GIMBLE4ES
-	default 0x3 if BOARD_GOOGLE_REDRIX
+	default 0x1 if BOARD_GOOGLE_REDRIX
+	default 0x3 if BOARD_GOOGLE_REDRIX4ES
 	default 0x1 if BOARD_GOOGLE_KANO
 	default 0x3 if BOARD_GOOGLE_TAEKO
 	default 0x1 if BOARD_GOOGLE_FELWINTER
diff --git a/src/mainboard/google/brya/variants/redrix/gpio.c b/src/mainboard/google/brya/variants/redrix/gpio.c
index afcb7e9114..f9fd731a96 100644
--- a/src/mainboard/google/brya/variants/redrix/gpio.c
+++ b/src/mainboard/google/brya/variants/redrix/gpio.c
@@ -81,10 +81,10 @@ static const struct pad_config early_gpio_table[] = {
 	PAD_CFG_GPO(GPP_A12, 1, DEEP),
 	/* A13 : PMC_I2C_SCL ==> GSC_PCH_INT_ODL */
 	PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT),
-	/* B7  : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */
-	PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2),
-	/* B8  : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */
-	PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2),
+	/* H6  : I2C1_SDA ==> PCH_I2C_TPM_SDA */
+	PAD_CFG_NF(GPP_H6, NONE, DEEP, NF1),
+	/* H7  : I2C1_SCL ==> PCH_I2C_TPM_SCL */
+	PAD_CFG_NF(GPP_H7, NONE, DEEP, NF1),
 	/*
 	 * D1  : ISH_GP1 ==> FP_RST_ODL
 	 * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down.
diff --git a/src/mainboard/google/brya/variants/redrix/overridetree.cb b/src/mainboard/google/brya/variants/redrix/overridetree.cb
index 9531e5e1a0..617ebc556e 100644
--- a/src/mainboard/google/brya/variants/redrix/overridetree.cb
+++ b/src/mainboard/google/brya/variants/redrix/overridetree.cb
@@ -57,29 +57,25 @@ chip soc/intel/alderlake
 	#+-------------------+---------------------------+
 	#| GSPI1             | Fingerprint MCU           |
 	#| I2C0              | Audio                     |
-	#| I2C1              | Touchscreen               |
-	#| I2C2              |                           |
-	#| I2C3              | cr50 TPM. Early init is   |
+	#| I2C1              | cr50 TPM. Early init is   |
 	#|                   | required to set up a BAR  |
 	#|                   | for TPM communication     |
+	#| I2C3              | TouchScreen               |
 	#| I2C5              | Trackpad                  |
 	#+-------------------+---------------------------+
 	register "common_soc_config" = "{
-		.i2c[0] = {
-			.speed = I2C_SPEED_FAST,
-		},
 		.i2c[1] = {
-			.speed = I2C_SPEED_FAST,
-		},
-		.i2c[2] = {
-			.speed = I2C_SPEED_FAST,
-		},
-		.i2c[3] = {
 			.early_init = 1,
 			.speed = I2C_SPEED_FAST,
+			.rise_time_ns = 600,
+			.fall_time_ns = 400,
+			.data_hold_time_ns = 50,
 		},
-		.i2c[5] = {
+		.i2c[3] = {
 			.speed = I2C_SPEED_FAST,
+			.rise_time_ns = 650,
+			.fall_time_ns = 400,
+			.data_hold_time_ns = 50,
 		},
 	}"
 	device domain 0 on
@@ -254,24 +250,10 @@ chip soc/intel/alderlake
 			end
 		end #I2C0
 		device ref i2c1 on
-			chip drivers/i2c/hid
-				register "generic.hid" = ""ELAN2513""
-				register "generic.desc" = ""ELAN Touchscreen""
-				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
-				register "generic.probed" = "1"
-				register "generic.reset_gpio" =
-							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
-				register "generic.reset_delay_ms" = "300"
-				register "generic.reset_off_delay_ms" = "1"
-				register "generic.enable_gpio" =
-							"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
-				register "generic.enable_delay_ms" = "6"
-				register "generic.stop_gpio" =
-							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
-				register "generic.stop_off_delay_ms" = "1"
-				register "generic.has_power_resource" = "1"
-				register "hid_desc_reg_offset" = "0x01"
-				device i2c 0x15 on end
+			chip drivers/i2c/tpm
+				register "hid" = ""GOOG0005""
+				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
+				device i2c 50 on end
 			end
 		end
 		device ref i2c2 on
@@ -388,10 +370,24 @@ chip soc/intel/alderlake
 
 		end
 		device ref i2c3 on
-			chip drivers/i2c/tpm
-				register "hid" = ""GOOG0005""
-				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
-				device i2c 50 on end
+			chip drivers/i2c/hid
+				register "generic.hid" = ""ELAN2513""
+				register "generic.desc" = ""ELAN Touchscreen""
+				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+				register "generic.probed" = "1"
+				register "generic.reset_gpio" =
+							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+				register "generic.reset_delay_ms" = "300"
+				register "generic.reset_off_delay_ms" = "1"
+				register "generic.enable_gpio" =
+							"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+				register "generic.enable_delay_ms" = "6"
+				register "generic.stop_gpio" =
+							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+				register "generic.stop_off_delay_ms" = "1"
+				register "generic.has_power_resource" = "1"
+				register "hid_desc_reg_offset" = "0x01"
+				device i2c 0x15 on end
 			end
 		end
 		device ref i2c5 on