diff --git a/Documentation/mainboard/hp/elitebook_820_g2.md b/Documentation/mainboard/hp/elitebook_820_g2.md new file mode 100644 index 0000000000..5d35c30211 --- /dev/null +++ b/Documentation/mainboard/hp/elitebook_820_g2.md @@ -0,0 +1,141 @@ +# HP EliteBook 820 G2 + +This page is about the notebook [HP EliteBook 820 G2]. + +## Release status + +HP EliteBook 820 G2 was released in 2015 and is now end of life. +It can be bought from a secondhand market like Taobao or eBay. + +## Required proprietary blobs + +The following blobs are required to operate the hardware: + +1. EC firmware +2. Intel ME firmware +3. Broadwell mrc.bin and refcode.elf + +HP EliteBook 820 G2 uses SMSC MEC1324 as its embedded controller. +The EC firmware is stored in the flash chip, but we don't need to touch it +or use it in the coreboot build process. + +Intel ME firmware is in the flash chip. It is not needed when building coreboot. + +The Broadwell memory reference code binary and reference code blob is needed +when building coreboot. Read the document [Blobs used in Intel Broadwell boards] +on how to get these blobs. + +## Programming + +Before flashing, remove the battery and the hard drive cover according to the +[Maintenance and Service Guide] of this laptop. + +HP EliteBook 820 G2 has two flash chips, a 16MiB system flash, and a 2MiB +private flash. To install coreboot, we need to program both flash chips. +Read [HP Sure Start] for detailed information. + +![HP EliteBook 820 G2 flash chip](elitebook_820_g2_flash.jpg) + +To access the system flash, we need to connect the AC adapter to the machine, +then clip on the flash chip with an SOIC-8 clip. An [STM32-based flash programmer] +made with an STM32 development board is tested to work. + +To access the private flash chip, we can use a ch341a based flash programmer and +flash the chip with the AC adapter disconnected. + +To flash coreboot on a board running OME firmware, create a backup for both flash +chips, then do the following: + +1. Erase the private flash to disable the IFD protection +2. Modify the IFD to shrink the BIOS region, so that we can put the firmware outside + the protected flash region + +To erase the private flash chip, attach it with the flash programmer via the SOIC-8 clip, +then run: + + flashrom -p --erase + +To modify the IFD, write the following flash layout to a file: + + 00000000:00000fff fd + 00001000:00002fff gbe + 00003000:005fffff me + 00600000:00bfffff bios + 00eb5000:00ffffff pd + +Suppose the above layout file is ``layout.txt`` and the origin content of the system flash +is in ``factory-sys.rom``, run: + + ifdtool -n layout.txt factory-sys.rom + +Then a flash image with a new IFD will be in ``factory-sys.rom.new``. + +Flash the IFD of the system flash: + + flashrom -p --ifd -i fd -w factory-sys.rom.new + +Then flash the coreboot image: + + # first extend the 12M coreboot.rom to 16M + fallocate -l 16M build/coreboot.rom + flashrom -p --ifd -i bios -w build/coreboot.rom + +After coreboot is installed, the coreboot firmware can be updated with internal flashing: + + flashrom -p internal --ifd -i bios --noverify-all -w build/coreboot.rom + +## Debugging + +The board can be debugged with EHCI debug. The EHCI debug port is the USB port on the left. + +## Test status + +### Untested + +- NFC module +- Fingerprint reader +- Smart Card reader + +### Working + +- mainboards with i3-5010U, i5-5300U CPU, 16G+8G DDR3L memory +- SATA and M.2 SATA disk +- PCIe SSD +- Webcam +- Touch screen +- Audio output from speaker and headphone jack +- Intel GbE (needs a modified refcode documented in [Blobs used in Intel Broadwell boards]) +- WLAN +- WWAN +- SD card reader +- Internal LCD, DisplayPort and VGA video outputs +- Dock +- USB +- Keyboard and touchpad +- EC ACPI +- S3 resume +- TPM +- Arch Linux with Linux 5.11.16 +- Broadwell MRC version 2.6.0 Build 0 and refcode from Purism Librem 13 v1 +- Graphics initialization with libgfxinit +- Payload: SeaBIOS 1.16.2 +- EC firmware: KBC Revision 96.54 from OEM firmware version 01.05 +- Internal flashing under coreboot + +## Technology + +```eval_rst ++------------------+-----------------------------+ +| SoC | Intel Broadwell | ++------------------+-----------------------------+ +| EC | SMSC MEC1324 | ++------------------+-----------------------------+ +| Coprocessor | Intel Management Engine | ++------------------+-----------------------------+ +``` + +[HP EliteBook 820 G2]: https://support.hp.com/us-en/product/HP-EliteBook-820-G2-Notebook-PC/7343192/ +[Blobs used in Intel Broadwell boards]: ../../soc/intel/broadwell/blobs.md +[Maintenance and Service Guide]: http://h10032.www1.hp.com/ctg/Manual/c04775894.pdf +[STM32-based flash programmer]: https://github.com/dword1511/stm32-vserprog +[HP Sure Start]: hp_sure_start.md diff --git a/Documentation/mainboard/hp/elitebook_820_g2_flash.jpg b/Documentation/mainboard/hp/elitebook_820_g2_flash.jpg new file mode 100644 index 0000000000..17115278ba Binary files /dev/null and b/Documentation/mainboard/hp/elitebook_820_g2_flash.jpg differ diff --git a/Documentation/mainboard/index.md b/Documentation/mainboard/index.md index f5b4ed8530..68532d5e8e 100644 --- a/Documentation/mainboard/index.md +++ b/Documentation/mainboard/index.md @@ -85,6 +85,7 @@ The boards in this section are not real mainboards, but emulators. - [EliteBook 2560p](hp/2560p.md) - [EliteBook 8760w](hp/8760w.md) - [EliteBook Folio 9480m](hp/folio_9480m.md) +- [EliteBook 820 G2](hp/elitebook_820_g2.md) ## Intel diff --git a/src/mainboard/hp/elitebook_820_g2/Kconfig b/src/mainboard/hp/elitebook_820_g2/Kconfig new file mode 100644 index 0000000000..98aed5ca1b --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/Kconfig @@ -0,0 +1,31 @@ +# SPDX-License-Identifier: GPL-2.0-or-later + +if BOARD_HP_ELITEBOOK_820_G2 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select BOARD_ROMSIZE_KB_12288 + select EC_HP_KBC1126 + select HAVE_ACPI_RESUME + select HAVE_ACPI_TABLES + select INTEL_GMA_HAVE_VBT + select MAINBOARD_HAS_LIBGFXINIT + select MAINBOARD_HAS_TPM1 + select MAINBOARD_USES_IFD_GBE_REGION + select MEMORY_MAPPED_TPM + select SOC_INTEL_BROADWELL + select SYSTEM_TYPE_LAPTOP + +config MAINBOARD_DIR + default "hp/elitebook_820_g2" + +config MAINBOARD_PART_NUMBER + default "EliteBook 820 G2" + +config EC_HP_KBC1126_ECFW_IN_CBFS + default n + +config EC_HP_KBC1126_GPE + default 0x6 + +endif diff --git a/src/mainboard/hp/elitebook_820_g2/Kconfig.name b/src/mainboard/hp/elitebook_820_g2/Kconfig.name new file mode 100644 index 0000000000..65495f070d --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/Kconfig.name @@ -0,0 +1,4 @@ +# SPDX-License-Identifier: GPL-2.0-or-later + +config BOARD_HP_ELITEBOOK_820_G2 + bool "EliteBook 820 G2" diff --git a/src/mainboard/hp/elitebook_820_g2/Makefile.inc b/src/mainboard/hp/elitebook_820_g2/Makefile.inc new file mode 100644 index 0000000000..774dbf19ae --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/Makefile.inc @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0-or-later + +romstage-y += gpio.c +romstage-y += pei_data.c +ramstage-$(CONFIG_MAINBOARD_USE_LIBGFXINIT) += gma-mainboard.ads +ramstage-y += pei_data.c diff --git a/src/mainboard/hp/elitebook_820_g2/acpi/ec.asl b/src/mainboard/hp/elitebook_820_g2/acpi/ec.asl new file mode 100644 index 0000000000..baa17a4181 --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/acpi/ec.asl @@ -0,0 +1,3 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include diff --git a/src/mainboard/hp/elitebook_820_g2/acpi/platform.asl b/src/mainboard/hp/elitebook_820_g2/acpi/platform.asl new file mode 100644 index 0000000000..8023ae826c --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/acpi/platform.asl @@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +Method(_WAK,1) +{ + \_SB.PCI0.LPCB.EC0.ACPI = 1 + \_SB.PCI0.LPCB.EC0.SLPT = 0 + + Return(Package(){0,0}) +} + +Method(_PTS,1) +{ + \_SB.PCI0.LPCB.EC0.SLPT = Arg0 +} diff --git a/src/mainboard/hp/elitebook_820_g2/acpi/superio.asl b/src/mainboard/hp/elitebook_820_g2/acpi/superio.asl new file mode 100644 index 0000000000..55b1db5b11 --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/acpi/superio.asl @@ -0,0 +1,3 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include diff --git a/src/mainboard/hp/elitebook_820_g2/board_info.txt b/src/mainboard/hp/elitebook_820_g2/board_info.txt new file mode 100644 index 0000000000..eec345937f --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/board_info.txt @@ -0,0 +1,7 @@ +Category: laptop +Board URL: https://support.hp.com/us-en/product/HP-EliteBook-820-G2-Notebook-PC/7343192/ +ROM protocol: SPI +ROM package: SOIC-8 +ROM socketed: n +Flashrom support: y +Release year: 2015 diff --git a/src/mainboard/hp/elitebook_820_g2/data.vbt b/src/mainboard/hp/elitebook_820_g2/data.vbt new file mode 100644 index 0000000000..563cdbad0f Binary files /dev/null and b/src/mainboard/hp/elitebook_820_g2/data.vbt differ diff --git a/src/mainboard/hp/elitebook_820_g2/devicetree.cb b/src/mainboard/hp/elitebook_820_g2/devicetree.cb new file mode 100644 index 0000000000..d6cb2ed016 --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/devicetree.cb @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: GPL-2.0-or-later + +chip soc/intel/broadwell + chip cpu/intel/haswell + device cpu_cluster 0 on ops broadwell_cpu_bus_ops end + end + device domain 0 on + ops broadwell_pci_domain_ops + subsystemid 0x103c 0x225a inherit + + device pci 00.0 on end # Broadwell Host bridge + device pci 02.0 on # Internal graphics VGA controller + register "gfx" = "GMA_STATIC_DISPLAYS(0)" + register "gpu_dp_b_hotplug" = "4" + register "gpu_dp_c_hotplug" = "4" + register "panel_cfg" = "{ + .up_delay_ms = 200, + .down_delay_ms = 50, + .cycle_delay_ms = 500, + .backlight_on_delay_ms = 1, + .backlight_off_delay_ms = 1, + .backlight_pwm_hz = 200, + }" + end + device pci 03.0 on end # Mini-HD audio + + chip soc/intel/broadwell/pch # Wildcat Point PCH + device pci 13.0 off end # Smart Sound Audio DSP + device pci 14.0 on end # xHCI Controller + device pci 15.0 off end # Serial I/O DMA + device pci 15.1 off end # I2C0 + device pci 15.2 off end # I2C1 + device pci 15.3 off end # GSPI0 + device pci 15.4 off end # GSPI1 + device pci 15.5 off end # UART0 + device pci 15.6 off end # UART1 + device pci 16.0 on end # Management Engine Interface 1 + device pci 16.1 off end # Management Engine Interface 2 + device pci 16.2 off end # Management Engine IDE-R + device pci 16.3 off end # Management Engine KT + device pci 17.0 off end # SDIO + device pci 19.0 on end # Intel Gigabit Ethernet + device pci 1b.0 on end # High Definition Audio + device pci 1c.0 on end # PCIe Port #1 + device pci 1c.1 on end # PCIe Port #2, Card Reader + device pci 1c.2 off end # PCIe Port #3 + device pci 1c.3 on # PCIe Port #4, WLAN + smbios_slot_desc "SlotTypeM2Socket1_SD" "SlotLengthOther" + "M.2/E 2230" "SlotDataBusWidth1X" + end + device pci 1c.4 off end # PCIe Port #5 + device pci 1c.5 on # PCIe Port #6, PCIe SSD + smbios_slot_desc "SlotTypeM2Socket3" "SlotLengthOther" + "M.2/M 2242/2260" "SlotDataBusWidth2X" + end + device pci 1d.0 on end # USB2 EHCI #1 + device pci 1f.0 on # LPC bridge + register "gen1_dec" = "0x007c0201" + register "gen2_dec" = "0x000c0101" + register "gen4_dec" = "0x000402e9" + register "gpe0_en_1" = "0x40" + register "gpe0_en_2" = "0x600" + register "gpe0_en_4" = "0x46" + chip drivers/pc80/tpm + device pnp 0c31.0 on end + end + # This laptop uses MEC1324, but it has the same interface + # as the KBC1126 laptops + chip ec/hp/kbc1126 + register "ec_data_port" = "0x62" + register "ec_cmd_port" = "0x66" + register "ec_ctrl_reg" = "0x81" + register "ec_fan_ctrl_value" = "0x6b" + device pnp ff.1 off end + end + end + device pci 1f.2 on # SATA Controller (AHCI) + register "sata_port1_gen3_dtle" = "0x2" + register "sata_port1_gen3_tx" = "0x80" + register "sata_port3_gen3_dtle" = "0x4" + register "sata_port3_gen3_tx" = "0x80" + # SATA (1), M.2 (3) + register "sata_port_map" = "0xa" + end + device pci 1f.3 on end # SMBus + device pci 1f.6 off end # Thermal + end + end +end diff --git a/src/mainboard/hp/elitebook_820_g2/dsdt.asl b/src/mainboard/hp/elitebook_820_g2/dsdt.asl new file mode 100644 index 0000000000..6d7555d02e --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/dsdt.asl @@ -0,0 +1,31 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include + +DefinitionBlock( + "dsdt.aml", + "DSDT", + ACPI_DSDT_REV_2, + OEM_ID, + ACPI_TABLE_CREATOR, + 0x20141018 /* OEM revision */ +) +{ + #include + + #include + #include "acpi/platform.asl" + #include + + #include + #include + #include + #include + + Device (\_SB.PCI0) + { + #include + #include + #include + } +} diff --git a/src/mainboard/hp/elitebook_820_g2/gma-mainboard.ads b/src/mainboard/hp/elitebook_820_g2/gma-mainboard.ads new file mode 100644 index 0000000000..3962512eec --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/gma-mainboard.ads @@ -0,0 +1,18 @@ +-- SPDX-License-Identifier: GPL-2.0-or-later + +with HW.GFX.GMA; +with HW.GFX.GMA.Display_Probing; + +use HW.GFX.GMA; +use HW.GFX.GMA.Display_Probing; + +private package GMA.Mainboard is + + ports : constant Port_List := + (DP1, -- All DisplayPorts + HDMI1, + DP2, -- VGA + eDP, + others => Disabled); + +end GMA.Mainboard; diff --git a/src/mainboard/hp/elitebook_820_g2/gpio.c b/src/mainboard/hp/elitebook_820_g2/gpio.c new file mode 100644 index 0000000000..8eb7bfd50c --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/gpio.c @@ -0,0 +1,110 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include + +const struct pch_lp_gpio_map mainboard_lp_gpio_map[] = { + [0] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [1] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [2] = LP_GPIO_OUT_LOW, + [3] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [4] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [5] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [6] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [7] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [8] = LP_GPIO_OUT_HIGH, + [9] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [10] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [11] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [12] = LP_GPIO_NATIVE, + [13] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [14] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [15] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [16] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL, + .route = GPIO_ROUTE_SMI }, + [17] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [18] = LP_GPIO_OUT_HIGH, + [19] = LP_GPIO_NATIVE, + [20] = LP_GPIO_NATIVE, + [21] = LP_GPIO_NATIVE, + [22] = LP_GPIO_NATIVE, + [23] = LP_GPIO_NATIVE, + [24] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL, + .reset = GPIO_RESET_RSMRST }, + [25] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [26] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [27] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [28] = LP_GPIO_OUT_HIGH, + [29] = LP_GPIO_OUT_LOW, + [30] = LP_GPIO_NATIVE, + [31] = LP_GPIO_NATIVE, + [32] = LP_GPIO_NATIVE, + [33] = LP_GPIO_NATIVE, + [34] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [35] = LP_GPIO_NATIVE, + [36] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL, + .route = GPIO_ROUTE_SMI }, + [37] = LP_GPIO_NATIVE, + [38] = LP_GPIO_NATIVE, + [39] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL, + .route = GPIO_ROUTE_SMI }, + [40] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL, + .route = GPIO_ROUTE_SMI }, + [41] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [42] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [43] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [44] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [45] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [46] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [47] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [48] = LP_GPIO_OUT_HIGH, + [49] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [50] = LP_GPIO_OUT_HIGH, + [51] = LP_GPIO_OUT_HIGH, + [52] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [53] = LP_GPIO_OUT_HIGH, + [54] = LP_GPIO_OUT_HIGH, + [55] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL, + .owner = GPIO_OWNER_GPIO, .irqen = GPIO_IRQ_ENABLE, + .pirq = GPIO_PIRQ_APIC_ROUTE }, + [56] = LP_GPIO_OUT_HIGH, + [57] = LP_GPIO_OUT_LOW, + [58] = LP_GPIO_OUT_HIGH, + [59] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [60] = LP_GPIO_OUT_HIGH, + [61] = LP_GPIO_OUT_LOW, + [62] = LP_GPIO_NATIVE, + [63] = LP_GPIO_NATIVE, + [64] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [65] = LP_GPIO_OUT_LOW, + [66] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [67] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [68] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [69] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_INVERT | GPIO_IRQ_LEVEL }, + [70] = LP_GPIO_OUT_LOW, + [71] = LP_GPIO_NATIVE, + [72] = LP_GPIO_NATIVE, + [73] = LP_GPIO_NATIVE, + [74] = LP_GPIO_NATIVE, + [75] = LP_GPIO_NATIVE, + [76] = LP_GPIO_NATIVE, + [77] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [78] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL, + .route = GPIO_ROUTE_SMI }, + [79] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [80] = LP_GPIO_OUT_LOW, + [81] = LP_GPIO_NATIVE, + [82] = LP_GPIO_OUT_HIGH, + [83] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [84] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [85] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [86] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [87] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [88] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [89] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [90] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [91] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [92] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [93] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + [94] = { .conf0 = GPIO_MODE_GPIO | GPIO_DIR_INPUT | GPIO_IRQ_LEVEL }, + LP_GPIO_END +}; diff --git a/src/mainboard/hp/elitebook_820_g2/hda_verb.c b/src/mainboard/hp/elitebook_820_g2/hda_verb.c new file mode 100644 index 0000000000..7199d3f827 --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/hda_verb.c @@ -0,0 +1,72 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include + +const u32 cim_verb_data[] = { + 0x10ec0280, /* Codec Vendor / Device ID: Realtek */ + 0x103c225a, /* Subsystem ID */ + 57, /* Number of 4 dword sets */ + + AZALIA_SUBVENDOR(0, 0x103c198f), + AZALIA_RESET(1), + AZALIA_PIN_CFG(0, 0x12, 0x90a60130), + AZALIA_PIN_CFG(0, 0x13, 0x40000000), + AZALIA_PIN_CFG(0, 0x14, 0x90170110), + AZALIA_PIN_CFG(0, 0x15, 0x0421101f), + AZALIA_PIN_CFG(0, 0x16, 0x411111f0), + AZALIA_PIN_CFG(0, 0x17, 0x411111f0), + AZALIA_PIN_CFG(0, 0x18, 0x411111f0), + AZALIA_PIN_CFG(0, 0x19, 0x411111f0), + AZALIA_PIN_CFG(0, 0x1a, 0x04a11020), + AZALIA_PIN_CFG(0, 0x1b, 0x411111f0), + AZALIA_PIN_CFG(0, 0x1d, 0x40748605), + AZALIA_PIN_CFG(0, 0x1e, 0x411111f0), + + 0x02050007, 0x0204c200, 0x02050063, 0x02044800, + 0x02050066, 0x02040809, 0x02050015, 0x02048842, + 0x0205000f, 0x0204cccc, 0x02050010, 0x0204ccdd, + 0x02050065, 0x02042000, 0x0205001c, 0x0204c900, + 0x02050018, 0x02043788, 0x02050008, 0x02048210, + 0x02050068, 0x02043022, 0x02050006, 0x02040800, + 0x02050061, 0x02040403, 0x02050061, 0x02040403, + 0x0205005f, 0x02040800, 0x02050060, 0x02040800, + 0x0205002c, 0x02044002, 0x0205002e, 0x02041ec4, + 0x0205002f, 0x02040000, 0x02050033, 0x0204c5e8, + 0x02050034, 0x02041a98, 0x02050035, 0x0204f5ad, + 0x02050036, 0x0204cbd2, 0x02050037, 0x02041605, + 0x02050038, 0x0204f5ad, 0x02050039, 0x0204ea5f, + 0x0205003a, 0x02040b42, 0x0205003b, 0x0204fb54, + 0x0205003c, 0x0204fcd9, 0x0205003d, 0x02040000, + 0x02050030, 0x02041f5c, 0x02050031, 0x02040111, + 0x02050032, 0x02041f5f, 0x0205003e, 0x02041ea9, + 0x0205002f, 0x02040000, 0x02050042, 0x0204c66e, + 0x02050043, 0x02041a29, 0x02050035, 0x0204f5ad, + 0x02050044, 0x0204ccdd, 0x02050045, 0x02041549, + 0x02050038, 0x0204f5ad, 0x02050046, 0x0204ee79, + 0x02050047, 0x020409f4, 0x0205003b, 0x0204fb54, + 0x02050048, 0x0204fa4c, 0x0205003d, 0x02040000, + 0x0205003f, 0x02041f4d, 0x02050040, 0x02040129, + 0x02050041, 0x02041f51, 0x02050049, 0x02041f61, + 0x0205002f, 0x02040000, 0x0205004d, 0x0204c2f4, + 0x0205004e, 0x02041d2e, 0x02050035, 0x0204f5ad, + 0x0205004f, 0x0204c5e8, 0x02050050, 0x02041a98, + 0x02050038, 0x0204f5ad, 0x02050051, 0x0204d30e, + 0x02050052, 0x020413e6, 0x0205003b, 0x0204fb54, + 0x02050053, 0x02040b73, 0x0205003d, 0x02040000, + 0x0205004a, 0x02041faf, 0x0205004b, 0x0204008a, + 0x0205004c, 0x02041fb0, 0x02050054, 0x02041fb0, + 0x0205002f, 0x02040000, 0x02050058, 0x0204c17a, + 0x02050059, 0x02041e8f, 0x02050035, 0x0204f5ad, + 0x0205005a, 0x0204c2f4, 0x0205005b, 0x02041d2e, + 0x02050038, 0x0204f5ad, 0x0205005c, 0x0204c899, + 0x0205005d, 0x0204195b, 0x0205003b, 0x0204fb54, + 0x0205005e, 0x02041444, 0x0205003d, 0x02040000, + 0x02050055, 0x02041fd8, 0x02050056, 0x02040045, + 0x02050057, 0x02041fd8, 0x0205002c, 0x0204ffc2, + 0x02050026, 0x02042828, 0x02050029, 0x02040250, + 0x02050004, 0x0204c09e, 0x0205000e, 0x02045001, +}; + +const u32 pc_beep_verbs[0] = {}; + +AZALIA_ARRAY_SIZES; diff --git a/src/mainboard/hp/elitebook_820_g2/pei_data.c b/src/mainboard/hp/elitebook_820_g2/pei_data.c new file mode 100644 index 0000000000..a31f2112cc --- /dev/null +++ b/src/mainboard/hp/elitebook_820_g2/pei_data.c @@ -0,0 +1,41 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include +#include + +void mb_get_spd_map(struct spd_info *spdi) +{ + spdi->addresses[0] = 0x50; + spdi->addresses[2] = 0x52; +} + +void mainboard_fill_pei_data(struct pei_data *pei_data) +{ + pei_data->ec_present = 1; + + /* P1 */ + pei_data_usb2_port(pei_data, 0, 0x0040, 1, USB_OC_PIN_SKIP, USB_PORT_BACK_PANEL); + /* P2: left side port, USB debug */ + pei_data_usb2_port(pei_data, 1, 0x0040, 1, USB_OC_PIN_SKIP, USB_PORT_BACK_PANEL); + /* P3: digitizer and right side ports (Microchip hub) */ + pei_data_usb2_port(pei_data, 2, 0x0040, 1, USB_OC_PIN_SKIP, USB_PORT_BACK_PANEL); + /* P4: WLAN */ + pei_data_usb2_port(pei_data, 3, 0x0040, 1, USB_OC_PIN_SKIP, USB_PORT_BACK_PANEL); + /* P5: fingerprint reader */ + pei_data_usb2_port(pei_data, 4, 0x0040, 1, USB_OC_PIN_SKIP, USB_PORT_BACK_PANEL); + /* P6: WWAN */ + pei_data_usb2_port(pei_data, 5, 0x0040, 1, USB_OC_PIN_SKIP, USB_PORT_BACK_PANEL); + /* P7: webcam */ + pei_data_usb2_port(pei_data, 6, 0x0040, 1, USB_OC_PIN_SKIP, USB_PORT_BACK_PANEL); + /* P8 */ + pei_data_usb2_port(pei_data, 7, 0x0040, 1, USB_OC_PIN_SKIP, USB_PORT_BACK_PANEL); + + /* P1 */ + pei_data_usb3_port(pei_data, 0, 1, USB_OC_PIN_SKIP, 0); + /* P2: left side, USB debug */ + pei_data_usb3_port(pei_data, 1, 1, USB_OC_PIN_SKIP, 0); + /* P3: right side (Microchip hub) */ + pei_data_usb3_port(pei_data, 2, 1, USB_OC_PIN_SKIP, 0); + /* P4 */ + pei_data_usb3_port(pei_data, 3, 1, USB_OC_PIN_SKIP, 0); +}