diff --git a/src/mainboard/via/epia-m700/romstage.c b/src/mainboard/via/epia-m700/romstage.c
index 6f8a1c09da..ab148e478d 100644
--- a/src/mainboard/via/epia-m700/romstage.c
+++ b/src/mainboard/via/epia-m700/romstage.c
@@ -58,7 +58,7 @@
  * This acpi_is_wakeup_early_via_VX800 is from Rudolf's patch on the list:
  * http://www.coreboot.org/pipermail/coreboot/2008-January/028787.html.
  */
-int acpi_is_wakeup_early_via_vx800(void)
+static int acpi_is_wakeup_early_via_vx800(void)
 {
 	device_t dev;
 	u16 tmp, result;
@@ -94,8 +94,6 @@ static inline int spd_read_byte(unsigned device, unsigned address)
 static void enable_mainboard_devices(void)
 {
 	device_t dev;
-	uint16_t values;
-
 #if 0
 	/*
 	 * Add and close this switch, since some line cause error, some
@@ -145,6 +143,8 @@ static void enable_mainboard_devices(void)
 #if 0
 	dev = 0;
 	dev = pci_locate_device(PCI_ID(0x1106, PCI_DEVICE_ID_VIA_VX855_IDE), 0);
+
+	uint16_t values;
 	values = pci_read_config16(dev, 0xBA);
 	values &= ~0xffff;
 	values |= 0x5324;
@@ -202,68 +202,68 @@ static void enable_shadow_ram(void)
  */
 static const struct VIA_PCI_REG_INIT_TABLE mNbStage1InitTbl[] = {
 	/* VT3409 no PCI-E */
-	0x00, 0xFF, NB_APIC_REG(0x61), 0xFF, 0x0E,	// Set Exxxxxxx as pcie mmio config range
-	0x00, 0xFF, NB_APIC_REG(0x60), 0xF4, 0x0B,	// Support extended cfg address of pcie
-	// 0x00, 0xFF, NB_APIC_REG(0x42), 0xF9, 0x02, // APIC Interrupt((BT_INTR)) Control
+	{ 0x00, 0xFF, NB_APIC_REG(0x61), 0xFF, 0x0E },	// Set Exxxxxxx as pcie mmio config range
+	{ 0x00, 0xFF, NB_APIC_REG(0x60), 0xF4, 0x0B },	// Support extended cfg address of pcie
+	// { 0x00, 0xFF, NB_APIC_REG(0x42), 0xF9, 0x02 }, // APIC Interrupt((BT_INTR)) Control
 	// Set ROMSIP value by software
 
 	/*
-	0x00, 0xFF, NB_HOST_REG(0x70), 0x77, 0x33, // 2x Host Adr Strobe/Pad Pullup Driving = 3
-	0x00, 0xFF, NB_HOST_REG(0x71), 0x77, 0x33, // 2x Host Adr Strobe/Pad Pulldown Driving = 3
-	0x00, 0xFF, NB_HOST_REG(0x72), 0x77, 0x33, // 4x Host Dat Strobe/Pad Pullup Driving = 3
-	0x00, 0xFF, NB_HOST_REG(0x73), 0x77, 0x33, // 4x Host Dat Strobe/Pad Pulldown Driving = 3
-	0x00, 0xFF, NB_HOST_REG(0x74), 0xFF, 0x21, // Memory I/F timing ctrl
-	0x00, 0xFF, NB_HOST_REG(0x74), 0xFF, 0xE1, // Memory I/F timing ctrl
-	0x00, 0xFF, NB_HOST_REG(0x75), 0xFF, 0x18, // AGTL+ I/O Circuit
-	0x00, 0xFF, NB_HOST_REG(0x76), 0xFB, 0x0C, // AGTL+ Compensation Status
-	0x00, 0xFF, NB_HOST_REG(0x78), 0xFF, 0x33, // 2X AGTL+ Auto Compensation Offset
-	0x00, 0xFF, NB_HOST_REG(0x79), 0xFF, 0x33, // 4X AGTL+ Auto Compensation Offset
-	0x00, 0xFF, NB_HOST_REG(0x7A), 0x3F, 0x72, // AGTL Compensation Status
-	0x00, 0xFF, NB_HOST_REG(0x7A), 0x3F, 0x77, // AGTL Compensation Status
-	0x00, 0xFF, NB_HOST_REG(0x7B), 0xFF, 0x44, // Input Host Address / Host Strobe Delay Control for HA Group
-	0x00, 0xFF, NB_HOST_REG(0x7B), 0xFF, 0x22, // Input Host Address / Host Strobe Delay Control for HA Group
-	0x00, 0xFF, NB_HOST_REG(0x7C), 0xFF, 0x00, // Output Delay Control of PAD for HA Group
-	0x00, 0xFF, NB_HOST_REG(0x7D), 0xFF, 0xAA, // Host Address / Address Clock Output Delay Control (Only for P4 Bus)
-	0x00, 0xFF, NB_HOST_REG(0x7E), 0xFF, 0x10, // Host Address CKG Rising / Falling Time Control (Only for P4 Bus)
-	0x00, 0xFF, NB_HOST_REG(0x7E), 0xFF, 0x40, // Host Address CKG Rising / Falling Time Control (Only for P4 Bus)
-	0x00, 0xFF, NB_HOST_REG(0x7F), 0xFF, 0x10, // Host Address CKG Rising / Falling Time Control (Only for P4 Bus)
-	0x00, 0xFF, NB_HOST_REG(0x7F), 0xFF, 0x40, // Host Address CKG Rising / Falling Time Control (Only for P4 Bus)
-	0x00, 0xFF, NB_HOST_REG(0x80), 0x3F, 0x44, // Host Data Receiving Strobe Delay Ctrl 1
-	0x00, 0xFF, NB_HOST_REG(0x81), 0xFF, 0x44, // Host Data Receiving Strobe Delay Ctrl 2
-	0x00, 0xFF, NB_HOST_REG(0x82), 0xFF, 0x00, // Output Delay of PAD for HDSTB
-	0x00, 0xFF, NB_HOST_REG(0x83), 0xFF, 0x00, // Output Delay of PAD for HD
-	0x00, 0xFF, NB_HOST_REG(0x84), 0xFF, 0x44, // Host Data / Strobe CKG Control (Group 0)
-	0x00, 0xFF, NB_HOST_REG(0x85), 0xFF, 0x44, // Host Data / Strobe CKG Control (Group 1)
-	0x00, 0xFF, NB_HOST_REG(0x86), 0xFF, 0x44, // Host Data / Strobe CKG Control (Group 2)
-	0x00, 0xFF, NB_HOST_REG(0x87), 0xFF, 0x44, // Host Data / Strobe CKG Control (Group 3)
+	{ 0x00, 0xFF, NB_HOST_REG(0x70), 0x77, 0x33 }, // 2x Host Adr Strobe/Pad Pullup Driving = 3
+	{ 0x00, 0xFF, NB_HOST_REG(0x71), 0x77, 0x33 }, // 2x Host Adr Strobe/Pad Pulldown Driving = 3
+	{ 0x00, 0xFF, NB_HOST_REG(0x72), 0x77, 0x33 }, // 4x Host Dat Strobe/Pad Pullup Driving = 3
+	{ 0x00, 0xFF, NB_HOST_REG(0x73), 0x77, 0x33 }, // 4x Host Dat Strobe/Pad Pulldown Driving = 3
+	{ 0x00, 0xFF, NB_HOST_REG(0x74), 0xFF, 0x21 }, // Memory I/F timing ctrl
+	{ 0x00, 0xFF, NB_HOST_REG(0x74), 0xFF, 0xE1 }, // Memory I/F timing ctrl
+	{ 0x00, 0xFF, NB_HOST_REG(0x75), 0xFF, 0x18 }, // AGTL+ I/O Circuit
+	{ 0x00, 0xFF, NB_HOST_REG(0x76), 0xFB, 0x0C }, // AGTL+ Compensation Status
+	{ 0x00, 0xFF, NB_HOST_REG(0x78), 0xFF, 0x33 }, // 2X AGTL+ Auto Compensation Offset
+	{ 0x00, 0xFF, NB_HOST_REG(0x79), 0xFF, 0x33 }, // 4X AGTL+ Auto Compensation Offset
+	{ 0x00, 0xFF, NB_HOST_REG(0x7A), 0x3F, 0x72 }, // AGTL Compensation Status
+	{ 0x00, 0xFF, NB_HOST_REG(0x7A), 0x3F, 0x77 }, // AGTL Compensation Status
+	{ 0x00, 0xFF, NB_HOST_REG(0x7B), 0xFF, 0x44 }, // Input Host Address / Host Strobe Delay Control for HA Group
+	{ 0x00, 0xFF, NB_HOST_REG(0x7B), 0xFF, 0x22 }, // Input Host Address / Host Strobe Delay Control for HA Group
+	{ 0x00, 0xFF, NB_HOST_REG(0x7C), 0xFF, 0x00 }, // Output Delay Control of PAD for HA Group
+	{ 0x00, 0xFF, NB_HOST_REG(0x7D), 0xFF, 0xAA }, // Host Address / Address Clock Output Delay Control (Only for P4 Bus)
+	{ 0x00, 0xFF, NB_HOST_REG(0x7E), 0xFF, 0x10 }, // Host Address CKG Rising / Falling Time Control (Only for P4 Bus)
+	{ 0x00, 0xFF, NB_HOST_REG(0x7E), 0xFF, 0x40 }, // Host Address CKG Rising / Falling Time Control (Only for P4 Bus)
+	{ 0x00, 0xFF, NB_HOST_REG(0x7F), 0xFF, 0x10 }, // Host Address CKG Rising / Falling Time Control (Only for P4 Bus)
+	{ 0x00, 0xFF, NB_HOST_REG(0x7F), 0xFF, 0x40 }, // Host Address CKG Rising / Falling Time Control (Only for P4 Bus)
+	{ 0x00, 0xFF, NB_HOST_REG(0x80), 0x3F, 0x44 }, // Host Data Receiving Strobe Delay Ctrl 1
+	{ 0x00, 0xFF, NB_HOST_REG(0x81), 0xFF, 0x44 }, // Host Data Receiving Strobe Delay Ctrl 2
+	{ 0x00, 0xFF, NB_HOST_REG(0x82), 0xFF, 0x00 }, // Output Delay of PAD for HDSTB
+	{ 0x00, 0xFF, NB_HOST_REG(0x83), 0xFF, 0x00 }, // Output Delay of PAD for HD
+	{ 0x00, 0xFF, NB_HOST_REG(0x84), 0xFF, 0x44 }, // Host Data / Strobe CKG Control (Group 0)
+	{ 0x00, 0xFF, NB_HOST_REG(0x85), 0xFF, 0x44 }, // Host Data / Strobe CKG Control (Group 1)
+	{ 0x00, 0xFF, NB_HOST_REG(0x86), 0xFF, 0x44 }, // Host Data / Strobe CKG Control (Group 2)
+	{ 0x00, 0xFF, NB_HOST_REG(0x87), 0xFF, 0x44 }, // Host Data / Strobe CKG Control (Group 3)
 	*/
 
 	// CPU Host Bus Control
-	0x00, 0xFF, NB_HOST_REG(0x50), 0x1F, 0x08,	// Request phase ctrl: Dynamic Defer Snoop Stall Count = 8
-	// 0x00, 0xFF, NB_HOST_REG(0x51), 0xFF, 0x7F,	// CPU I/F Ctrl-1: Disable Fast DRDY and RAW
-	0x00, 0xFF, NB_HOST_REG(0x51), 0xFF, 0x7C,	// CPU I/F Ctrl-1: Disable Fast DRDY and RAW
-	0x00, 0xFF, NB_HOST_REG(0x52), 0xCB, 0xCB,	// CPU I/F Ctrl-2: Enable all for performance
-	// 0x00, 0xFF, NB_HOST_REG(0x53), 0xFF, 0x88,	// Arbitration: Host/Master Occupancy timer = 8*4 HCLK
-	0x00, 0xFF, NB_HOST_REG(0x53), 0xFF, 0x44,	// Arbitration: Host/Master Occupancy timer = 4*4 HCLK
-	0x00, 0xFF, NB_HOST_REG(0x54), 0x1E, 0x1C,	// Misc Ctrl: Enable 8QW burst Mem Access
-	// 0x00, 0xFF, NB_HOST_REG(0x55), 0x06, 0x06,	// Miscellaneous Control 2
-	0x00, 0xFF, NB_HOST_REG(0x55), 0x06, 0x04,	// Miscellaneous Control 2
-	0x00, 0xFF, NB_HOST_REG(0x56), 0xF7, 0x63,	// Write Policy 1
-	// 0x00, 0xFF, NB_HOST_REG(0x59), 0x3D, 0x01,	// CPU Miscellaneous Control 1, enable Lowest-Priority IPL
-	// 0x00, 0xFF, NB_HOST_REG(0x5c), 0xFF, 0x00,	// CPU Miscellaneous Control 2
-	0x00, 0xFF, NB_HOST_REG(0x5D), 0xFF, 0xA2,	// Write Policy
-	0x00, 0xFF, NB_HOST_REG(0x5E), 0xFF, 0x88,	// Bandwidth Timer
-	0x00, 0xFF, NB_HOST_REG(0x5F), 0x46, 0x46,	// CPU Misc Ctrl
-	// 0x00, 0xFF, NB_HOST_REG(0x90), 0xFF, 0x0B,	// CPU Miscellaneous Control 3
-	// 0x00, 0xFF, NB_HOST_REG(0x96), 0x0B, 0x0B,	// CPU Miscellaneous Control 2
-	0x00, 0xFF, NB_HOST_REG(0x96), 0x0B, 0x0A,	// CPU Miscellaneous Control 2
-	0x00, 0xFF, NB_HOST_REG(0x98), 0xC1, 0x41,	// CPU Miscellaneous Control 3
-	0x00, 0xFF, NB_HOST_REG(0x99), 0x0E, 0x06,	// CPU Miscellaneous Control 4
+	{ 0x00, 0xFF, NB_HOST_REG(0x50), 0x1F, 0x08 },	// Request phase ctrl: Dynamic Defer Snoop Stall Count = 8
+	// { 0x00, 0xFF, NB_HOST_REG(0x51), 0xFF, 0x7F },	// CPU I/F Ctrl-1: Disable Fast DRDY and RAW
+	{ 0x00, 0xFF, NB_HOST_REG(0x51), 0xFF, 0x7C },	// CPU I/F Ctrl-1: Disable Fast DRDY and RAW
+	{ 0x00, 0xFF, NB_HOST_REG(0x52), 0xCB, 0xCB },	// CPU I/F Ctrl-2: Enable all for performance
+	// { 0x00, 0xFF, NB_HOST_REG(0x53), 0xFF, 0x88 },	// Arbitration: Host/Master Occupancy timer = 8*4 HCLK
+	{ 0x00, 0xFF, NB_HOST_REG(0x53), 0xFF, 0x44 },	// Arbitration: Host/Master Occupancy timer = 4*4 HCLK
+	{ 0x00, 0xFF, NB_HOST_REG(0x54), 0x1E, 0x1C },	// Misc Ctrl: Enable 8QW burst Mem Access
+	// { 0x00, 0xFF, NB_HOST_REG(0x55), 0x06, 0x06 },	// Miscellaneous Control 2
+	{ 0x00, 0xFF, NB_HOST_REG(0x55), 0x06, 0x04 },	// Miscellaneous Control 2
+	{ 0x00, 0xFF, NB_HOST_REG(0x56), 0xF7, 0x63 },	// Write Policy 1
+	// { 0x00, 0xFF, NB_HOST_REG(0x59), 0x3D, 0x01 },	// CPU Miscellaneous Control 1, enable Lowest-Priority IPL
+	// { 0x00, 0xFF, NB_HOST_REG(0x5c), 0xFF, 0x00 },	// CPU Miscellaneous Control 2
+	{ 0x00, 0xFF, NB_HOST_REG(0x5D), 0xFF, 0xA2 },	// Write Policy
+	{ 0x00, 0xFF, NB_HOST_REG(0x5E), 0xFF, 0x88 },	// Bandwidth Timer
+	{ 0x00, 0xFF, NB_HOST_REG(0x5F), 0x46, 0x46 },	// CPU Misc Ctrl
+	// { 0x00, 0xFF, NB_HOST_REG(0x90), 0xFF, 0x0B },	// CPU Miscellaneous Control 3
+	// { 0x00, 0xFF, NB_HOST_REG(0x96), 0x0B, 0x0B },	// CPU Miscellaneous Control 2
+	{ 0x00, 0xFF, NB_HOST_REG(0x96), 0x0B, 0x0A },	// CPU Miscellaneous Control 2
+	{ 0x00, 0xFF, NB_HOST_REG(0x98), 0xC1, 0x41 },	// CPU Miscellaneous Control 3
+	{ 0x00, 0xFF, NB_HOST_REG(0x99), 0x0E, 0x06 },	// CPU Miscellaneous Control 4
 
 	// Set APIC and SMRAM
-	0x00, 0xFF, NB_HOST_REG(0x97), 0xFF, 0x00,	// APIC Related Control
-	0x00, 0xFF, NB_DRAMC_REG(0x86), 0xD6, 0x29,	// SMM and APIC Decoding: enable APIC, MSI and SMRAM A-Seg
-	0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00	// End of the table
+	{ 0x00, 0xFF, NB_HOST_REG(0x97), 0xFF, 0x00 },	// APIC Related Control
+	{ 0x00, 0xFF, NB_DRAMC_REG(0x86), 0xD6, 0x29 },	// SMM and APIC Decoding: enable APIC, MSI and SMRAM A-Seg
+	{ 0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }	// End of the table
 };
 
 #define USE_VCP     1		/* 0 means "use DVP". */
@@ -383,7 +383,6 @@ void EmbedComInit(void)
 /* cache_as_ram.inc jumps to here. */
 void main(unsigned long bist)
 {
-	unsigned cpu_reset = 0;
 	u16 boot_mode;
 	u8 rambits, Data8, Data;
 	device_t device;
diff --git a/src/northbridge/via/vx800/detection.c b/src/northbridge/via/vx800/detection.c
index 51aa9fa302..6bbfef0168 100644
--- a/src/northbridge/via/vx800/detection.c
+++ b/src/northbridge/via/vx800/detection.c
@@ -17,6 +17,11 @@
  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
  */
 
+/* FIXME this should go away */
+static const struct mem_controller ctrl = {
+	.channel0 = {0x50, 0x51},
+};
+
 #define SMBUS_ADDR_CH_A_1       0xA0	/* Dimmx */
 #define SMBUS_ADDR_CH_A_2       0xA2	/* Dimmx */
 #define SMBUS_ADDR_CH_B_1       0xA4	/* Dimmx */
diff --git a/src/northbridge/via/vx800/dev_init.c b/src/northbridge/via/vx800/dev_init.c
index 3a29d29aca..c3097cf2cb 100644
--- a/src/northbridge/via/vx800/dev_init.c
+++ b/src/northbridge/via/vx800/dev_init.c
@@ -166,7 +166,7 @@ Purpose   : DRAM initialize according to the bios porting guid
 #define EXIST_TEST_PATTERN		0x55555555
 #define NOT_EXIST_TEST_PATTERN		0xAAAAAAAA
 
-BOOLEAN ChkForExistLowBank(void)
+static BOOLEAN ChkForExistLowBank(void)
 {
 	u32 *Address, data32;
 
@@ -207,9 +207,6 @@ BOOLEAN ChkForExistLowBank(void)
 	return TRUE;
 }
 
-void InitDDR2CHC(DRAM_SYS_ATTR *DramAttr);
-void InitDDR2CHB(DRAM_SYS_ATTR *DramAttr);
-
 void DRAMInitializeProc(DRAM_SYS_ATTR *DramAttr)
 {
 	u8 shift, idx;
diff --git a/src/northbridge/via/vx800/dram_init.h b/src/northbridge/via/vx800/dram_init.h
index 27f73f0f4d..fc0117e2db 100644
--- a/src/northbridge/via/vx800/dram_init.h
+++ b/src/northbridge/via/vx800/dram_init.h
@@ -121,10 +121,6 @@ struct mem_controller {
 	u8 channel0[MAX_DIMMS];
 };
 
-static const struct mem_controller ctrl = {
-	.channel0 = {0x50, 0x51},
-};
-
 typedef struct _DRAM_CONFIG_DATA {
 	u8 DramClk;
 	u8 DramTiming;
diff --git a/src/northbridge/via/vx800/drdy_bl.c b/src/northbridge/via/vx800/drdy_bl.c
index da8aae13c8..393f623f25 100644
--- a/src/northbridge/via/vx800/drdy_bl.c
+++ b/src/northbridge/via/vx800/drdy_bl.c
@@ -404,10 +404,7 @@ static const u8 PT894_64bit_DELAYMD1_RCONV0[6][6][PT894_RDRDY_TBL_Width] =
 
 void DRAMDRDYSetting(DRAM_SYS_ATTR * DramAttr)
 {
-	u8 Data, CL, RDRPH;
-	u8 CpuFreq, DramFreq;
-	u8 ProgData[PT894_RDRDY_TBL_Width];
-
+	u8 Data;
 	/*
 	   this function has 3 switchs, correspond to 3 level of Drdy setting.
 	   0:Slowest, 1:Default, 2:Optimize
@@ -464,6 +461,9 @@ void DRAMDRDYSetting(DRAM_SYS_ATTR * DramAttr)
 	}
 #endif
 #if 0				//  2:Optimize
+	u8 CpuFreq, DramFreq;
+	u8 CL, RDRPH;
+
 	//CL :reg6x[2:0]
 	Data = pci_read_config8(MEMCTRL, 0x62);
 	CL = Data & 0x07;
@@ -484,6 +484,8 @@ void DRAMDRDYSetting(DRAM_SYS_ATTR * DramAttr)
 	DelayMode = CL + RDRPH;	// RDELAYMD = bit0 of (CAS Latency + RDRPH)
 	DelayMode &= 0x01;
 
+	u8 ProgData[PT894_RDRDY_TBL_Width];
+
 	//In 364, there is no 128 bit
 	if (DelayMode == 1) {	// DelayMode 1
 		u8 Index;
diff --git a/src/northbridge/via/vx800/examples/chipset_init.c b/src/northbridge/via/vx800/examples/chipset_init.c
index 08d3c95048..8cee44504b 100644
--- a/src/northbridge/via/vx800/examples/chipset_init.c
+++ b/src/northbridge/via/vx800/examples/chipset_init.c
@@ -43,12 +43,12 @@ static const struct VIA_PCI_REG_INIT_TABLE mSbStage1InitTbl[] = {
 	{0x00, 0xFF, SB_VLINK_REG(0xE6), 0xFF, 0x39},	// Enable SMM A-Seg, MSI and Io APIC
 	///// SPI-BAR.
 	//// SPI_BASE_ADDRESS = 0xFED1 0000
-	0x00, 0xFF, SB_LPC_REG(0xBC), 0xFF, 0x00,
-	0x00, 0xFF, SB_LPC_REG(0xBD), 0xFF, 0xD1,
-	0x00, 0xFF, SB_LPC_REG(0xBE), 0xFF, 0xFE,
-//      0x00, 0xFF, ((0x11<<16)|(0x00<<8)|0xBC), 0xFF, 0x00,//this , for the different macro
-//      0x00, 0xFF, ((0x11<<16)|(0x00<<8)|0xBD), 0xFF, 0xD1,
-//      0x00, 0xFF, ((0x11<<16)|(0x00<<8)|0xBE), 0xFF, 0xFE,
+	{0x00, 0xFF, SB_LPC_REG(0xBC), 0xFF, 0x00},
+	{0x00, 0xFF, SB_LPC_REG(0xBD), 0xFF, 0xD1},
+	{0x00, 0xFF, SB_LPC_REG(0xBE), 0xFF, 0xFE},
+//      {0x00, 0xFF, ((0x11<<16)|(0x00<<8)|0xBC), 0xFF, 0x00},//this , for the different macro
+//      {0x00, 0xFF, ((0x11<<16)|(0x00<<8)|0xBD), 0xFF, 0xD1},
+//      {0x00, 0xFF, ((0x11<<16)|(0x00<<8)|0xBE), 0xFF, 0xFE},
 	///// End of 2008-04-17
 
 	{0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00},	// End of Table
@@ -60,191 +60,184 @@ static const struct VIA_PCI_REG_INIT_TABLE mNbStage2InitTable[] = {
 	// D0F2~D0F3 is configured by MemoryInit Peim
 
 	// D0F4: NB PMU
-	0x00, 0xFF, NB_PMU_REG(0x84), 0x00, 0xDB,
-	0x00, 0xFF, NB_PMU_REG(0x85), 0x00, 0x05,
-	0x00, 0xFF, NB_PMU_REG(0x89), 0x00, 0xF8,
-	0x00, 0xFF, NB_PMU_REG(0x8B), 0x00, 0xBF,
-	0x00, 0xFF, NB_PMU_REG(0x8D), 0x00, 0xFC,
-	0x00, 0xFF, NB_PMU_REG(0x8E), 0x00, 0x19,
-	0x00, 0xFF, NB_PMU_REG(0x8F), 0x03, 0x00,
-	0x00, 0xFF, NB_PMU_REG(0x90), 0x00, 0xFF,
-	0x00, 0xFF, NB_PMU_REG(0x91), 0x00, 0xFF,
-	0x00, 0xFF, NB_PMU_REG(0x92), 0x00, 0xCC,
-	0x00, 0xFF, NB_PMU_REG(0xA0), 0x00, 0x80,
-	0x00, 0xFF, NB_PMU_REG(0xA1), 0x00, 0xE0,
-	0x00, 0xFF, NB_PMU_REG(0xA2), 0x00, 0xD6,
-	0x00, 0xFF, NB_PMU_REG(0xA3), 0x00, 0x80,
-	0x00, 0xFF, NB_PMU_REG(0xA8), 0x00, 0x20,
+	{ 0x00, 0xFF, NB_PMU_REG(0x84), 0x00, 0xDB },
+	{ 0x00, 0xFF, NB_PMU_REG(0x85), 0x00, 0x05 },
+	{ 0x00, 0xFF, NB_PMU_REG(0x89), 0x00, 0xF8 },
+	{ 0x00, 0xFF, NB_PMU_REG(0x8B), 0x00, 0xBF },
+	{ 0x00, 0xFF, NB_PMU_REG(0x8D), 0x00, 0xFC },
+	{ 0x00, 0xFF, NB_PMU_REG(0x8E), 0x00, 0x19 },
+	{ 0x00, 0xFF, NB_PMU_REG(0x8F), 0x03, 0x00 },
+	{ 0x00, 0xFF, NB_PMU_REG(0x90), 0x00, 0xFF },
+	{ 0x00, 0xFF, NB_PMU_REG(0x91), 0x00, 0xFF },
+	{ 0x00, 0xFF, NB_PMU_REG(0x92), 0x00, 0xCC },
+	{ 0x00, 0xFF, NB_PMU_REG(0xA0), 0x00, 0x80 },
+	{ 0x00, 0xFF, NB_PMU_REG(0xA1), 0x00, 0xE0 },
+	{ 0x00, 0xFF, NB_PMU_REG(0xA2), 0x00, 0xD6 },
+	{ 0x00, 0xFF, NB_PMU_REG(0xA3), 0x00, 0x80 },
+	{ 0x00, 0xFF, NB_PMU_REG(0xA8), 0x00, 0x20 },
 
 	// D0F5: NB APIC, PXPTRF and MSGC
 	//Note: the Rx6A, RCRBH Base Address, is not set, which is related to PCIE Root Complex.
 	//Note: the Rx60, Extended CFG Address. Support and Rx61, Extended CFG Address, are set by NB Peim that is in the PEI Phase.
 	//Note: the Rx42, APIC Interrupt((BT_INTR)) Control, is set by NB Peim that is in PEI phase.
-	0x00, 0xFF, NB_PXPTRF_REG(0x50), 0x00, 0x00,
-	0x00, 0xFF, NB_PXPTRF_REG(0x54), 0x00, 0x80,
-	0x00, 0xFF, NB_PXPTRF_REG(0x55), 0x00, 0x04,
-	0x00, 0xFF, NB_PXPTRF_REG(0x58), 0x00, 0x00,
-	0x00, 0xFF, NB_PXPTRF_REG(0x59), 0x00, 0x02,
-	0x00, 0xFF, NB_PXPTRF_REG(0x5E), 0x00, 0x00,
-	0x00, 0xFF, NB_PXPTRF_REG(0x5F), 0x00, 0x06,
-	0x00, 0xFF, NB_PXPTRF_REG(0x80), 0x00, 0x18,	//Set RVC1DM, RTHBHIT, RUWRDYD, RUPRRDY1, RUWPOPHD to 1.
-	0x00, 0xFF, NB_PXPTRF_REG(0x82), 0x00, 0x00,	//Set RVC1RPSW, RVC1RQ1T to 1.
-	0x00, 0xFF, NB_PXPTRF_REG(0x83), 0x00, 0x81,
-	0x00, 0xFF, NB_PXPTRF_REG(0x84), 0x00, 0x28,
-	0x00, 0xFF, NB_PXPTRF_REG(0x85), 0x00, 0xC0,
-	0x00, 0xFF, NB_MSGC_REG(0xA3), 0x00, 0x01,	// RWAKEEN
-//  0x00, 0xFF, NB_PXPTRF_REG(0x64), 0x40, 0x00, //RTDNP2B32EN
-	0x00, 0xFF, NB_PXPTRF_REG(0xF3), 0xFC, 0x20,
-	0x00, 0xFF, NB_PXPTRF_REG(0x85), 0x00, 0x00,	//RP2P1ABORT
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x50), 0x00, 0x00 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x54), 0x00, 0x80 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x55), 0x00, 0x04 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x58), 0x00, 0x00 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x59), 0x00, 0x02 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x5E), 0x00, 0x00 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x5F), 0x00, 0x06 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x80), 0x00, 0x18 },	//Set RVC1DM, RTHBHIT, RUWRDYD, RUPRRDY1, RUWPOPHD to 1.
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x82), 0x00, 0x00 },	//Set RVC1RPSW, RVC1RQ1T to 1.
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x83), 0x00, 0x81 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x84), 0x00, 0x28 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x85), 0x00, 0xC0 },
+	{ 0x00, 0xFF, NB_MSGC_REG(0xA3), 0x00, 0x01 },	// RWAKEEN
+	//{ 0x00, 0xFF, NB_PXPTRF_REG(0x64), 0x40, 0x00 }, //RTDNP2B32EN
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0xF3), 0xFC, 0x20 },
+	{ 0x00, 0xFF, NB_PXPTRF_REG(0x85), 0x00, 0x00 },	//RP2P1ABORT
 
 
 // fine-tune
 // If no settings, C7 will hang or reboot in XP, but CN will not.
-	0x00, 0xFF, NB_HOST_REG(0x51), 0x84, 0x00,
-	0x00, 0xFF, NB_HOST_REG(0x52), 0x0F, 0x03,
-	0x00, 0xFF, NB_HOST_REG(0x54), 0x04, 0x00,
-	0x00, 0xFF, NB_HOST_REG(0x55), 0x04, 0x00,
-	0x00, 0xFF, NB_HOST_REG(0x59), 0x09, 0x01,
-	0x00, 0xFF, NB_HOST_REG(0x5C), 0x10, 0x10,
-	0x00, 0xFF, NB_HOST_REG(0x5F), 0x0E, 0x08,
-	0x00, 0xFF, NB_HOST_REG(0x92), 0xFF, 0x04,	// ACPI Base addr
-	0x00, 0xFF, NB_HOST_REG(0x97), 0x01, 0x01,	// APIC MSI
-	0x00, 0xFF, NB_HOST_REG(0x99), 0x02, 0x00,	// APIC MSI
+	{ 0x00, 0xFF, NB_HOST_REG(0x51), 0x84, 0x00 },
+	{ 0x00, 0xFF, NB_HOST_REG(0x52), 0x0F, 0x03 },
+	{ 0x00, 0xFF, NB_HOST_REG(0x54), 0x04, 0x00 },
+	{ 0x00, 0xFF, NB_HOST_REG(0x55), 0x04, 0x00 },
+	{ 0x00, 0xFF, NB_HOST_REG(0x59), 0x09, 0x01 },
+	{ 0x00, 0xFF, NB_HOST_REG(0x5C), 0x10, 0x10 },
+	{ 0x00, 0xFF, NB_HOST_REG(0x5F), 0x0E, 0x08 },
+	{ 0x00, 0xFF, NB_HOST_REG(0x92), 0xFF, 0x04 },	// ACPI Base addr
+	{ 0x00, 0xFF, NB_HOST_REG(0x97), 0x01, 0x01 },	// APIC MSI
+	{ 0x00, 0xFF, NB_HOST_REG(0x99), 0x02, 0x00 },	// APIC MSI
 	//GTL
-	0x00, 0xFF, NB_HOST_REG(0x73), 0xFF, 0x66,
-	0x00, 0xFF, NB_HOST_REG(0xB2), 0xFF, 0x33,
-	0x00, 0xFF, NB_HOST_REG(0xB3), 0xFF, 0x33,
-	0x00, 0xFF, NB_HOST_REG(0xBC), 0xFF, 0x33,
-	0x00, 0xFF, NB_HOST_REG(0xBD), 0xFF, 0x33,
-	0x00, 0xFF, NB_HOST_REG(0xC5), 0x30, 0x20,
-	0x00, 0xFF, NB_HOST_REG(0xC8), 0x10, 0x00,
+	{ 0x00, 0xFF, NB_HOST_REG(0x73), 0xFF, 0x66 },
+	{ 0x00, 0xFF, NB_HOST_REG(0xB2), 0xFF, 0x33 },
+	{ 0x00, 0xFF, NB_HOST_REG(0xB3), 0xFF, 0x33 },
+	{ 0x00, 0xFF, NB_HOST_REG(0xBC), 0xFF, 0x33 },
+	{ 0x00, 0xFF, NB_HOST_REG(0xBD), 0xFF, 0x33 },
+	{ 0x00, 0xFF, NB_HOST_REG(0xC5), 0x30, 0x20 },
+	{ 0x00, 0xFF, NB_HOST_REG(0xC8), 0x10, 0x00 },
 
 
 	// End of Table
 	{0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00},	// End of Table
-
 };
 
 static const struct VIA_PCI_REG_INIT_TABLE mBusControllerInitTable[] = {
 	// D17F0: LPC
-	0x00, 0xFF, SB_LPC_REG(0x40), 0x44, 0x44,	//  Enable I/O Recovery Time,  4D0/4D1 Support
-	0x00, 0xFF, SB_LPC_REG(0x42), 0xF8, 0xF0,	//  ENLBUF, GINTREN, FLUSHEN, RBRSTRD
-	0x00, 0xFF, SB_LPC_REG(0x43), 0x0F, 0x0B,	//  RENDTX, ENWBTO, ENRBTO
-	//  0x00, 0xFF, SB_LPC_REG(0x46), 0x00, 0x10,     // It is related to INTH#
-	//0x00, 0xFF, SB_LPC_REG(0x48), 0x00, 0x0C,      //RMRPW, RIRPW  // Reserved in 409 by Eric
+	{ 0x00, 0xFF, SB_LPC_REG(0x40), 0x44, 0x44 },	//  Enable I/O Recovery Time,  4D0/4D1 Support
+	{ 0x00, 0xFF, SB_LPC_REG(0x42), 0xF8, 0xF0 },	//  ENLBUF, GINTREN, FLUSHEN, RBRSTRD
+	{ 0x00, 0xFF, SB_LPC_REG(0x43), 0x0F, 0x0B },	//  RENDTX, ENWBTO, ENRBTO
+	//{ 0x00, 0xFF, SB_LPC_REG(0x46), 0x00, 0x10 },     // It is related to INTH#
+	//{ 0x00, 0xFF, SB_LPC_REG(0x48), 0x00, 0x0C },      //RMRPW, RIRPW  // Reserved in 409 by Eric
 
 	// Internal RTC, Mouse, Keyboard // set in PEI by Eric
-	//0x00, 0xFF, SB_LPC_REG(0x51), 0x10, 0x0D,      // Enable Internal RTC, Internal PS2 Mouse/Keyboard
+	//{ 0x00, 0xFF, SB_LPC_REG(0x51), 0x10, 0x0D },      // Enable Internal RTC, Internal PS2 Mouse/Keyboard
 
 	// RTC
-	0x00, 0xFF, SB_LPC_REG(0x58), 0x00, 0x01,	//RTC Rx32 Map to Centrury Byte
+	{ 0x00, 0xFF, SB_LPC_REG(0x58), 0x00, 0x01 },	//RTC Rx32 Map to Centrury Byte
 
-	// 0x00, 0xFF, SB_LPC_REG(0x40), 0x00, 0x02,    // RDMEGAS
-	//0x00, 0xFF, SB_LPC_REG(0x4E), 0x00, 0x08,  // Enable RTC port 74/75, ENEXRTC // set in PEI by Eric
+	//{ 0x00, 0xFF, SB_LPC_REG(0x40), 0x00, 0x02 },    // RDMEGAS
+	//{ 0x00, 0xFF, SB_LPC_REG(0x4E), 0x00, 0x08 },  // Enable RTC port 74/75, ENEXRTC // set in PEI by Eric
 
 	// Serial IRQ  // set in PEI by Eric
-	//0x00, 0xFF, SB_LPC_REG(0x52), 0x0F, 0x09,    // Enable Serial IRQ, Start Frame Width is 6 PCI Clock.
+	//{ 0x00, 0xFF, SB_LPC_REG(0x52), 0x0F, 0x09 },    // Enable Serial IRQ, Start Frame Width is 6 PCI Clock.
 
 	// Enable 4D0h/4D1h Port
-	//0x00, 0xFF, SB_LPC_REG(0x40), 0x00, 0x04,    // EISAXT // set in PEI by Eric
+	//{ 0x00, 0xFF, SB_LPC_REG(0x40), 0x00, 0x04 },    // EISAXT // set in PEI by Eric
 
 	// Config ROM Interface
 	// Enable SPI/Set SPI Memory Base Address
 	// It is initialized in PEI Phase
 
 	// Subsystem ID/Vendor ID Back Door
-	0x00, 0xFF, SB_LPC_REG(0x70), 0xFF, 0x06,
-	0x00, 0xFF, SB_LPC_REG(0x71), 0xFF, 0x11,
-	0x00, 0xFF, SB_LPC_REG(0x72), 0xFF, 0x09,
-	0x00, 0xFF, SB_LPC_REG(0x73), 0xFF, 0x34,
+	{ 0x00, 0xFF, SB_LPC_REG(0x70), 0xFF, 0x06 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x71), 0xFF, 0x11 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x72), 0xFF, 0x09 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x73), 0xFF, 0x34 },
 
-	0x00, 0xFF, SB_LPC_REG(0x4C), 0xC0, 0x40,
-	0x00, 0xFF, SB_LPC_REG(0x5B), 0x00, 0x51,	// Orgin value 0x53, modify for 409 by Eric
-	0x00, 0xFF, SB_LPC_REG(0x67), 0x03, 0x01,
+	{ 0x00, 0xFF, SB_LPC_REG(0x4C), 0xC0, 0x40 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x5B), 0x00, 0x51 },	// Orgin value 0x53, modify for 409 by Eric
+	{ 0x00, 0xFF, SB_LPC_REG(0x67), 0x03, 0x01 },
 
 
-	0x00, 0xFF, SB_LPC_REG(0x50), 0x7E, 0x00,	// Setting PCI device enable
-	0x00, 0xFF, SB_LPC_REG(0x51), 0xD0, 0x00,	// Setting PCI device enable
-	0x00, 0xFF, SB_VLINK_REG(0xD1), 0x04, 0x00,	// Setting HDAC enable
+	{ 0x00, 0xFF, SB_LPC_REG(0x50), 0x7E, 0x00 },	// Setting PCI device enable
+	{ 0x00, 0xFF, SB_LPC_REG(0x51), 0xD0, 0x00 },	// Setting PCI device enable
+	{ 0x00, 0xFF, SB_VLINK_REG(0xD1), 0x04, 0x00 },	// Setting HDAC enable
 	{0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00},	// End of Table
 };
 
 static const struct VIA_PCI_REG_INIT_TABLE mPCI1InitTable[] = {
 	//PCI1 Programming Sequence
 	//(1)Configure D17F7
-	0x00, 0xFF, SB_VLINK_REG(0x04), 0x00, 0x03,
-	0x00, 0xFF, SB_VLINK_REG(0x0C), 0x00, 0x08,	// Reserved in 409 by Eric
-	0x00, 0xFF, SB_VLINK_REG(0x4F), 0x40, 0x41,	//RENPPB, RP2CFLSH
-	0x00, 0xFF, SB_VLINK_REG(0x77), 0x00, 0x48,	//ROP2CFLSH, RFFTMR[1:0]. ROP2CFLSH work with Rx4F[0](RP2CFLSH) assertion
-	// 0x00, 0xFF, SB_VLINK_REG(0x51), 0x00, 0x80,      //RSUB_DEC_P2P, RSUBDECOD(Window xp). If Bit7 is set, PCI lock will occured.
-	//0x00, 0xFF, SB_VLINK_REG(0x51), 0x00, 0x81,      //RSUB_DEC_P2P, RSUBDECOD(Window Vista)
+	{ 0x00, 0xFF, SB_VLINK_REG(0x04), 0x00, 0x03 },
+	{ 0x00, 0xFF, SB_VLINK_REG(0x0C), 0x00, 0x08 },	// Reserved in 409 by Eric
+	{ 0x00, 0xFF, SB_VLINK_REG(0x4F), 0x40, 0x41 },	//RENPPB, RP2CFLSH
+	{ 0x00, 0xFF, SB_VLINK_REG(0x77), 0x00, 0x48 },	//ROP2CFLSH, RFFTMR[1:0]. ROP2CFLSH work with Rx4F[0](RP2CFLSH) assertion
+	// { 0x00, 0xFF, SB_VLINK_REG(0x51), 0x00, 0x80 },      //RSUB_DEC_P2P, RSUBDECOD(Window xp). If Bit7 is set, PCI lock will occured.
+	// { 0x00, 0xFF, SB_VLINK_REG(0x51), 0x00, 0x81 },      //RSUB_DEC_P2P, RSUBDECOD(Window Vista)
 	//(2)Configure D19F0
-	0x00, 0xFF, SB_P2PB_REG(0x04), 0x00, 0x07,
+	{ 0x00, 0xFF, SB_P2PB_REG(0x04), 0x00, 0x07 },
 
 	//(3)Performance Recommended Setting
 
 	//Save Power
-	0x00, 0xFF, SB_VLINK_REG(0xE2), 0x1F, 0x01,
-	0x00, 0xFF, SB_VLINK_REG(0xE3), 0xF1, 0x5E,
-	0x00, 0xFF, SB_VLINK_REG(0x74), 0x40, 0x00,
+	{ 0x00, 0xFF, SB_VLINK_REG(0xE2), 0x1F, 0x01 },
+	{ 0x00, 0xFF, SB_VLINK_REG(0xE3), 0xF1, 0x5E },
+	{ 0x00, 0xFF, SB_VLINK_REG(0x74), 0x40, 0x00 },
 	//Enhence Host To PCI cycle performance and PCI-To-Host Cycle performance
-	0x00, 0xFF, SB_VLINK_REG(0x70), 0x00, 0x82,
-	0x00, 0xFF, SB_VLINK_REG(0x71), 0x30, 0xC0,
-	0x00, 0xFF, SB_VLINK_REG(0x72), 0x00, 0xEE,
+	{ 0x00, 0xFF, SB_VLINK_REG(0x70), 0x00, 0x82 },
+	{ 0x00, 0xFF, SB_VLINK_REG(0x71), 0x30, 0xC0 },
+	{ 0x00, 0xFF, SB_VLINK_REG(0x72), 0x00, 0xEE },
 
 	//Cycle Control
-	0x00, 0xFF, SB_VLINK_REG(0x73), 0x00, 0x01,
-	0x00, 0xFF, SB_VLINK_REG(0x74), 0x00, 0x0C,
+	{ 0x00, 0xFF, SB_VLINK_REG(0x73), 0x00, 0x01 },
+	{ 0x00, 0xFF, SB_VLINK_REG(0x74), 0x00, 0x0C },
 	//Arbitration control
-	0x00, 0xFF, SB_VLINK_REG(0x75), 0x00, 0x0F,
-	0x00, 0xFF, SB_VLINK_REG(0x76), 0x00, 0xD0,
+	{ 0x00, 0xFF, SB_VLINK_REG(0x75), 0x00, 0x0F },
+	{ 0x00, 0xFF, SB_VLINK_REG(0x76), 0x00, 0xD0 },
 	{0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00},	// End of Table
 };
 
 static const struct VIA_PCI_REG_INIT_TABLE mCCAInitTable[] = {
-
-	0x00, 0xFF, SB_VLINK_REG(0xFC), 0x02, 0x08,	//RVWREQ, ROABKDOOR
+	{ 0x00, 0xFF, SB_VLINK_REG(0xFC), 0x02, 0x08 },	//RVWREQ, ROABKDOOR
 
 	//CCA's Register Programming sequence
-	0x00, 0xFF, SB_VLINK_REG(0x50), 0x00, 0x08,	//Config Azalia's upstream cycle high priority and other low priority
-	0x00, 0xFF, SB_VLINK_REG(0x51), 0x40, 0x80,	//Disable bypass asynchronous circuit
-	0x00, 0xFF, SB_VLINK_REG(0x52), 0x00, 0x11,	// Set SM Internal Device and HDAC Occupy Timer
-	0x00, 0xFF, SB_VLINK_REG(0x53), 0x00, 0x11,	// Set SM Internal Device and HDAC Promote Timer
-	0x00, 0xFF, SB_VLINK_REG(0x54), 0xFF, 0x02,	//Use SB internal devices's original REQ
-	0x00, 0xFF, SB_VLINK_REG(0x73), 0x10, 0x00,	//RPINOWSC. Enable APIC Cycle Block P2C Write Cycle
-	0x00, 0xFF, SB_VLINK_REG(0x74), 0x00, 0x3C,	//RLCKXP2C, RFSBVK.
-	0x00, 0xFF, SB_VLINK_REG(0xE1), 0x07, 0x00,	//RBLKAPIC, RAZC3
-	0x00, 0xFF, SB_VLINK_REG(0x7C), 0x04, 0x02,	//RNMIFSB, RFSBVK
-	0x00, 0xFF, SB_VLINK_REG(0xE0), 0xF0, 0x90,	//RCCA_NEWCLK, RCCA_CLKON. Use New dynamic clock scheme
-	0x00, 0xFF, SB_VLINK_REG(0xE7), 0xFF, 0x00,	//Let CCA use dynamic clock.
+	{ 0x00, 0xFF, SB_VLINK_REG(0x50), 0x00, 0x08 },	//Config Azalia's upstream cycle high priority and other low priority
+	{ 0x00, 0xFF, SB_VLINK_REG(0x51), 0x40, 0x80 },	//Disable bypass asynchronous circuit
+	{ 0x00, 0xFF, SB_VLINK_REG(0x52), 0x00, 0x11 },	// Set SM Internal Device and HDAC Occupy Timer
+	{ 0x00, 0xFF, SB_VLINK_REG(0x53), 0x00, 0x11 },	// Set SM Internal Device and HDAC Promote Timer
+	{ 0x00, 0xFF, SB_VLINK_REG(0x54), 0xFF, 0x02 },	//Use SB internal devices's original REQ
+	{ 0x00, 0xFF, SB_VLINK_REG(0x73), 0x10, 0x00 },	//RPINOWSC. Enable APIC Cycle Block P2C Write Cycle
+	{ 0x00, 0xFF, SB_VLINK_REG(0x74), 0x00, 0x3C },	//RLCKXP2C, RFSBVK.
+	{ 0x00, 0xFF, SB_VLINK_REG(0xE1), 0x07, 0x00 },	//RBLKAPIC, RAZC3
+	{ 0x00, 0xFF, SB_VLINK_REG(0x7C), 0x04, 0x02 },	//RNMIFSB, RFSBVK
+	{ 0x00, 0xFF, SB_VLINK_REG(0xE0), 0xF0, 0x90 },	//RCCA_NEWCLK, RCCA_CLKON. Use New dynamic clock scheme
+	{ 0x00, 0xFF, SB_VLINK_REG(0xE7), 0xFF, 0x00 },	//Let CCA use dynamic clock.
 	//The CCA is also relate to D17F0
-	//    0x00, 0xFF, SB_LPC_REG(0x49), 0x1F, 0x00,       //Disable CCA Test Mode
-	0x00, 0xFF, SB_LPC_REG(0x74), 0xFF, 0x00,	// Let DMA cycles from internal devices directly go to NB // Reserved in 409 by Eric
+	//{ 0x00, 0xFF, SB_LPC_REG(0x49), 0x1F, 0x00 },       //Disable CCA Test Mode
+	{ 0x00, 0xFF, SB_LPC_REG(0x74), 0xFF, 0x00 },	// Let DMA cycles from internal devices directly go to NB // Reserved in 409 by Eric
 	{0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00},	// End of Table
 };
 
 static const struct VIA_PCI_REG_INIT_TABLE IDEC_INIT[] = {
-
-	// 0x00, 0xFF, SB_IDEC_REG(0x09), 0x00, 0x05, //set to native mode
-	0x00, 0xFF, SB_IDEC_REG(0x04), 0x00, 0x07,
-	//0x00, 0xFF, SB_VLINK_REG(0x7C), 0x00, 0x7F,
+	//{0x00, 0xFF, SB_IDEC_REG(0x09), 0x00, 0x05}, //set to native mode
+	{0x00, 0xFF, SB_IDEC_REG(0x04), 0x00, 0x07},
+	//{0x00, 0xFF, SB_VLINK_REG(0x7C), 0x00, 0x7F},
 	{0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00},	// End of Table
-
 };
 
 static const struct VIA_PCI_REG_INIT_TABLE mSbApicInitTable[] = {
-	0x00, 0xFF, SB_LPC_REG(0x4D), 0x04, 0x00,
-	0x00, 0xFF, SB_LPC_REG(0x5B), 0x0E, 0x00,
-	0x00, 0xFF, SB_LPC_REG(0x6C), 0x08, 0x00,
-	0x00, 0xFF, SB_LPC_REG(0x58), 0x00, 0x40,
-	0x00, 0xFF, SB_VLINK_REG(0x74), 0x00, 0x04,
-	//0x00, 0xFF, SB_VLINK_REG(0x7C), 0x00, 0x7F,
-	{0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00},	// End of Table
-
+	{ 0x00, 0xFF, SB_LPC_REG(0x4D), 0x04, 0x00 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x5B), 0x0E, 0x00 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x6C), 0x08, 0x00 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x58), 0x00, 0x40 },
+	{ 0x00, 0xFF, SB_VLINK_REG(0x74), 0x00, 0x04 },
+	//{ 0x00, 0xFF, SB_VLINK_REG(0x7C), 0x00, 0x7F },
+	{ 0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },	// End of Table
 };
 
-
-
 void AcpiInit(void)
 {
 	device_t_raw rawdevice = 0;
@@ -268,10 +261,8 @@ void AcpiInit(void)
 
 	// Close all SMI/Io Traps
 	outb(0x00, VX800_ACPI_IO_BASE + 0x42);
-
 }
 
-
 void Stage2NbInit(void)
 {
 	device_t_raw rawdevice = 0;
@@ -290,7 +281,6 @@ void Stage2NbInit(void)
 
 	//vx855 NB no pcie bus
 	//vx855 NB no apic
-
 }
 
 void IDECSupportOption(u8 sbchiprev)
@@ -313,7 +303,6 @@ void InitIDEC(u8 sbchiprev)
 	IDECSupportOption(sbchiprev);
 }
 
-
 void InitUHCI(u8 Number, u8 bEnable)
 {
 	u8 Mask, Value;
@@ -374,25 +363,24 @@ void InitUHCI(u8 Number, u8 bEnable)
 
 static const struct VIA_PCI_REG_INIT_TABLE mEHCIInitTable[] = {
 	//EHCI
-	0x00, 0xFF, SB_EHCI_REG(0x43), 0x00, 0xC0,
-	0x00, 0xFF, SB_EHCI_REG(0x50), 0x00, 0x80,
-	0x00, 0xFF, SB_EHCI_REG(0x48), 0x20, 0x9E,
-	0x00, 0xFF, SB_EHCI_REG(0x49), 0x10, 0x68,
-	0x00, 0xFF, SB_EHCI_REG(0x4B), 0x00, 0x69,
-	0x00, 0xFF, SB_EHCI_REG(0x4D), 0x00, 0x94,
-	0x00, 0xFF, SB_EHCI_REG(0x52), 0x08, 0x00,
-	0x00, 0xFF, SB_EHCI_REG(0x5A), 0x00, 0x8A,
-	0x00, 0xFF, SB_EHCI_REG(0x5B), 0x00, 0x89,
-	0x00, 0xFF, SB_EHCI_REG(0x5C), 0x00, 0x03,
-	0x00, 0xFF, SB_EHCI_REG(0x5D), 0x00, 0x9A,
-	0x00, 0xFF, SB_EHCI_REG(0x5E), 0x00, 0x00,
-	0x00, 0xFF, SB_EHCI_REG(0x6B), 0x00, 0x00,
-	0x00, 0xFF, SB_EHCI_REG(0x6D), 0x00, 0x00,
-	0x00, 0xFF, SB_EHCI_REG(0x6F), 0xF0, 0x00,
-	0x00, 0xFF, SB_EHCI_REG(0x4E), 0x01, 0x01,
-	0x00, 0xFF, SB_EHCI_REG(0x4F), 0x00, 0x11,
-	{0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00},	// End of Table
-
+	{ 0x00, 0xFF, SB_EHCI_REG(0x43), 0x00, 0xC0 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x50), 0x00, 0x80 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x48), 0x20, 0x9E },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x49), 0x10, 0x68 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x4B), 0x00, 0x69 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x4D), 0x00, 0x94 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x52), 0x08, 0x00 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x5A), 0x00, 0x8A },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x5B), 0x00, 0x89 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x5C), 0x00, 0x03 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x5D), 0x00, 0x9A },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x5E), 0x00, 0x00 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x6B), 0x00, 0x00 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x6D), 0x00, 0x00 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x6F), 0xF0, 0x00 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x4E), 0x01, 0x01 },
+	{ 0x00, 0xFF, SB_EHCI_REG(0x4F), 0x00, 0x11 },
+	{ 0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },	// End of Table
 };
 
 void InitEHCI(u8 Number, u8 bEnable)
@@ -483,23 +471,23 @@ void HpetInit(void)
 
 static const struct VIA_PCI_REG_INIT_TABLE mPMUInitTable[] = {
 	// Power Management
-	0x00, 0xFF, SB_LPC_REG(0x80), 0x00, 0x20,
-	0x00, 0xFF, SB_LPC_REG(0x8C), 0x02, 0x00,
-	0x00, 0xFF, SB_LPC_REG(0x8D), 0x00, 0x18,
+	{ 0x00, 0xFF, SB_LPC_REG(0x80), 0x00, 0x20 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x8C), 0x02, 0x00 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x8D), 0x00, 0x18 },
 
 	//Miscellaneous Configuration 1
-	0x00, 0xFF, SB_LPC_REG(0x94), 0xF0, 0x28,
-	0x00, 0xFF, SB_LPC_REG(0x95), 0x00, 0xC1,
-	0x00, 0xFF, SB_LPC_REG(0x96), 0xFF, 0x10,
-	0x00, 0xFF, SB_LPC_REG(0x97), 0x00, 0xB2,
+	{ 0x00, 0xFF, SB_LPC_REG(0x94), 0xF0, 0x28 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x95), 0x00, 0xC1 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x96), 0xFF, 0x10 },
+	{ 0x00, 0xFF, SB_LPC_REG(0x97), 0x00, 0xB2 },
 
 	//Voltage Change Function Enable
-	0x00, 0xFF, SB_LPC_REG(0x9F), 0x00, 0x21,
+	{ 0x00, 0xFF, SB_LPC_REG(0x9F), 0x00, 0x21 },
 	//Internal PCIe and NM PLL Control
-	0x00, 0xFF, SB_LPC_REG(0xE2), 0x00, 0xEA,
+	{ 0x00, 0xFF, SB_LPC_REG(0xE2), 0x00, 0xEA },
 
-	0x00, 0xFF, SB_LPC_REG(0xE7), 0x00, 0x80,
-	{0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00},	// End of Table
+	{ 0x00, 0xFF, SB_LPC_REG(0xE7), 0x00, 0x80 },
+	{ 0x00, 0xFF, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },	// End of Table
 };
 
 void InitPMU(u8 sbchiprev)
@@ -589,7 +577,6 @@ void Stage2SbInit(void)
 
 }
 
-
 void init_VIA_chipset(void)
 {
 	printk(BIOS_DEBUG, "In: init_VIA_chipset\n");
@@ -633,7 +620,6 @@ void hardwaremain(int boot_complete)
 	printk(BIOS_EMERG, "file '%s', line %d\n\n", __FILE__, __LINE__);
 
 #if 0
-
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0, 4), 0xa3, 0x80);
 	pci_rawwrite_config8(PCI_RAWDEV(0, 17, 7), 0x60, 0x20);
 	pci_rawwrite_config8(PCI_RAWDEV(0, 17, 7), 0xE5,
@@ -656,7 +642,6 @@ void hardwaremain(int boot_complete)
 	printk(BIOS_INFO, "=================SB 50h=%02x \n",
 		    pci_rawread_config8(PCI_RAWDEV(0, 0x11, 0), 0x50));
 
-
 	/* FIXME: Is there a better way to handle this? */
 	init_timer();
 	printk(BIOS_EMERG, "file '%s', line %d\n\n", __FILE__, __LINE__);
@@ -690,9 +675,7 @@ void hardwaremain(int boot_complete)
 		y = 0;
 		for (; y < 16; y++) {
 			printk(BIOS_INFO, "%02x ",
-				    pci_rawread_config8(PCI_RAWDEV
-							(0, 0x10, 4),
-							x * 16 + y));
+			   pci_rawread_config8(PCI_RAWDEV (0, 0x10, 4), x * 16 + y));
 		}
 		printk(BIOS_INFO, "\n");
 	}
@@ -710,9 +693,7 @@ void hardwaremain(int boot_complete)
 		y = 0;
 		for (; y < 16; y++) {
 			printk(BIOS_INFO, "%02x ",
-				    pci_rawread_config8(PCI_RAWDEV
-							(0, 0x10, 4),
-							x * 16 + y));
+			    pci_rawread_config8(PCI_RAWDEV (0, 0x10, 4), x * 16 + y));
 		}
 		printk(BIOS_INFO, "\n");
 	}
@@ -722,7 +703,6 @@ void hardwaremain(int boot_complete)
 	post_code(0x89);
 	printk(BIOS_EMERG, "file '%s', line %d\n\n", __FILE__, __LINE__);
 
-
 //          pci_rawwrite_config16(PCI_RAWDEV(0, 0xf, 0), 0xBA, 0x0571);
 
 #if 0
@@ -732,17 +712,13 @@ void hardwaremain(int boot_complete)
 		y = 0;
 		for (; y < 16; y++) {
 			printk(BIOS_INFO, "%02x ",
-				    pci_rawread_config8(PCI_RAWDEV
-							(0, 0x10, 4),
-							x * 16 + y));
+			    pci_rawread_config8(PCI_RAWDEV (0, 0x10, 4), x * 16 + y));
 		}
 		printk(BIOS_INFO, "\n");
 	}
 #endif
 
-
 #if 0
-
 	y = pci_rawread_config8(PCI_RAWDEV(0, 0xf, 0), 0x0d);
 	y &= 0x0f;
 	y |= 0x40;
@@ -750,8 +726,6 @@ void hardwaremain(int boot_complete)
 #endif
 
 #if 0
-
-
 	static const d0f0pcitable[5] = { 0xD0, 0, 0, 0, 0xFD };
 	static const d0f2pcitable[16 * 7 + 1] = {
 		0x88, 0xF8, 0xEF, 0x44, 0x7C, 0x24, 0x63, 0x01, 0x00, 0x09,
@@ -911,7 +885,6 @@ void hardwaremain(int boot_complete)
 		    0x00, 0x00, 0x48, 0x00, 0x00, 0x00,
 	};
 
-
 #define OPTION_1 1
 #define NOOPTION_1 1
 #ifdef OPTION_1
@@ -943,24 +916,19 @@ void hardwaremain(int boot_complete)
 	};
 #endif
 
-
-
 	u8 i;
 /* error form ---- but add the chance to resume
-for(i=0;i<5;i++){
+	for(i=0;i<5;i++) {
 		pci_rawwrite_config8(PCI_RAWDEV(0, 0, 0), i, d0f0pcitable[i+0xcb]);
 	}
-
-
 */
 
 /* RO reg
-for(i=0;i<5;i++){
+	for(i=0;i<5;i++) {
 		pci_rawwrite_config8(PCI_RAWDEV(0, 0, 0), i+0xcb, d0f0pcitable[i]);
 	}
 */
 
-
 //boot ok, resume still err in linux
 #if 1
 	for (i = 0; i < 9; i++) {
@@ -1052,11 +1020,7 @@ for(i=0;i<5;i++){
 
 //d15f0
 
-
-
-
 #if 1
-
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x10, 0), 0x4a, 0xa2);	// no affect.
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x10, 1), 0x4a, 0xa2);
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x10, 2), 0x4a, 0xa2);
@@ -1077,8 +1041,6 @@ for(i=0;i<5;i++){
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x10, 4), 0x6f, 0x80);
 #endif
 
-
-
 #if 1
 //before (11.0)is add, s3 resume has already always dead in first resume(more frequenly), and sleep ok
 //      for(i=0;i<192;i++){
@@ -1094,7 +1056,6 @@ for(i=0;i<5;i++){
 				     d11f0pcitable[i]);
 	}
 
-
 	for (i = 18; i < 21; i++) {	//sleep ok ,   sleep err 1, resume
 		pci_rawwrite_config8(PCI_RAWDEV(0, 0x11, 0), i + 0x40,
 				     d11f0pcitable[i]);
@@ -1225,7 +1186,6 @@ for(i=0;i<5;i++){
 	pci_rawwrite_config16(PCI_RAWDEV(0, 0x11, 0), 0x72,
 			      PCI_DEVICE_ID_VIA_VX855_LPC);
 
-
 //boot ok, resume still err in linux
 	for (i = 0; i < 192; i++) {
 		pci_rawwrite_config8(PCI_RAWDEV(0, 0x11, 7), i + 0x40,
@@ -1240,17 +1200,12 @@ for(i=0;i<5;i++){
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x11, 7), 0x88, 0x02);
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x11, 7), 0xe6, 0x3f);
 #endif
-
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x14, 0), 0x40, 0x20);
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x14, 0), 0x41, 0x31);
 
-
-
 #ifdef OPTION_1
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x14, 0), 0x40, 0x00);
 #endif
-
-
 #endif
 
 	u8 i911;
@@ -1262,10 +1217,9 @@ for(i=0;i<5;i++){
 	i911 |= 0x01;
 	pci_rawwrite_config8(PCI_RAWDEV(0, 0x1, 0), 0xb0, i911);
 
-
 #if 1
 	struct device *dev;
-	printk(BIOS_INFO, "=========zjldump all  devices...\n");
+	printk(BIOS_INFO, "========= dump all  devices...\n");
 	for (dev = all_devices; dev; dev = dev->next) {
 		if (dev->path.type == DEVICE_PATH_PCI) {
 			printk(BIOS_DEBUG, "%s dump\n", dev_path(dev));
@@ -1274,25 +1228,14 @@ for(i=0;i<5;i++){
 				y = 0;
 				for (; y < 16; y++) {
 					printk(BIOS_INFO, "%02x ",
-						    pci_read_config8(dev,
-								     x *
-								     16 +
-								     y));
+					    pci_read_config8(dev, x * 16 + y));
 				}
 				printk(BIOS_INFO, "\n");
 			}
-
 		}
 		printk(BIOS_INFO, "\n");
 	}
 #endif
-
-
-
-
 	//pci_rawmodify_config8(PCI_RAWDEV(0, 0x10, 4), 0x04, 0x17, 0x17);//
-//      pci_rawmodify_config8(PCI_RAWDEV(0, 0x10, 4), 0x0c, 0x08, 0xff);///
-
-
-
+	//pci_rawmodify_config8(PCI_RAWDEV(0, 0x10, 4), 0x0c, 0x08, 0xff);///
 }
diff --git a/src/northbridge/via/vx800/pci_rawops.h b/src/northbridge/via/vx800/pci_rawops.h
index d0aa392a5a..7fabc3e105 100644
--- a/src/northbridge/via/vx800/pci_rawops.h
+++ b/src/northbridge/via/vx800/pci_rawops.h
@@ -37,13 +37,16 @@ struct VIA_PCI_REG_INIT_TABLE {
 	u8 Mask;
 	u8 Value;
 };
+
 typedef unsigned device_t_raw;	/* pci and pci_mmio need to have different ways to have dev */
 
+#warning "FIXME: get rid of this extra copy of pci access functions."
+
 /* FIXME: We need to make the coreboot to run at 64bit mode, So when read/write memory above 4G,
  * We don't need to set %fs, and %gs anymore
  * Before that We need to use %gs, and leave %fs to other RAM access
  */
-u8 pci_io_rawread_config8(device_t_raw dev, unsigned where)
+static u8 pci_io_rawread_config8(device_t_raw dev, unsigned where)
 {
 	unsigned addr;
 #if CONFIG_PCI_IO_CFG_EXT == 0
@@ -56,14 +59,14 @@ u8 pci_io_rawread_config8(device_t_raw dev, unsigned where)
 }
 
 #if CONFIG_MMCONF_SUPPORT
-u8 pci_mmio_rawread_config8(device_t_raw dev, unsigned where)
+static u8 pci_mmio_rawread_config8(device_t_raw dev, unsigned where)
 {
 	unsigned addr;
 	addr = dev | where;
 	return read8x(addr);
 }
 #endif
-u8 pci_rawread_config8(device_t_raw dev, unsigned where)
+static u8 pci_rawread_config8(device_t_raw dev, unsigned where)
 {
 #if CONFIG_MMCONF_SUPPORT
 	return pci_mmio_rawread_config8(dev, where);
@@ -72,7 +75,7 @@ u8 pci_rawread_config8(device_t_raw dev, unsigned where)
 #endif
 }
 
-u16 pci_io_rawread_config16(device_t_raw dev, unsigned where)
+static u16 pci_io_rawread_config16(device_t_raw dev, unsigned where)
 {
 	unsigned addr;
 #if CONFIG_PCI_IO_CFG_EXT == 0
@@ -85,7 +88,7 @@ u16 pci_io_rawread_config16(device_t_raw dev, unsigned where)
 }
 
 #if CONFIG_MMCONF_SUPPORT
-u16 pci_mmio_rawread_config16(device_t_raw dev, unsigned where)
+static u16 pci_mmio_rawread_config16(device_t_raw dev, unsigned where)
 {
 	unsigned addr;
 	addr = dev | where;
@@ -93,7 +96,7 @@ u16 pci_mmio_rawread_config16(device_t_raw dev, unsigned where)
 }
 #endif
 
-u16 pci_rawread_config16(device_t_raw dev, unsigned where)
+static u16 pci_rawread_config16(device_t_raw dev, unsigned where)
 {
 #if CONFIG_MMCONF_SUPPORT
 	return pci_mmio_rawread_config16(dev, where);
@@ -102,7 +105,7 @@ u16 pci_rawread_config16(device_t_raw dev, unsigned where)
 #endif
 }
 
-u32 pci_io_rawread_config32(device_t_raw dev, unsigned where)
+static u32 pci_io_rawread_config32(device_t_raw dev, unsigned where)
 {
 	unsigned addr;
 #if CONFIG_PCI_IO_CFG_EXT == 0
@@ -115,7 +118,7 @@ u32 pci_io_rawread_config32(device_t_raw dev, unsigned where)
 }
 
 #if CONFIG_MMCONF_SUPPORT
-u32 pci_mmio_rawread_config32(device_t_raw dev, unsigned where)
+static u32 pci_mmio_rawread_config32(device_t_raw dev, unsigned where)
 {
 	unsigned addr;
 	addr = dev | where;
@@ -123,7 +126,7 @@ u32 pci_mmio_rawread_config32(device_t_raw dev, unsigned where)
 }
 #endif
 
-u32 pci_rawread_config32(device_t_raw dev, unsigned where)
+static u32 pci_rawread_config32(device_t_raw dev, unsigned where)
 {
 #if CONFIG_MMCONF_SUPPORT
 	return pci_mmio_rawread_config32(dev, where);
@@ -132,7 +135,7 @@ u32 pci_rawread_config32(device_t_raw dev, unsigned where)
 #endif
 }
 
-void pci_io_rawwrite_config8(device_t_raw dev, unsigned where, u8 value)
+static void pci_io_rawwrite_config8(device_t_raw dev, unsigned where, u8 value)
 {
 	unsigned addr;
 #if CONFIG_PCI_IO_CFG_EXT == 0
@@ -145,7 +148,7 @@ void pci_io_rawwrite_config8(device_t_raw dev, unsigned where, u8 value)
 }
 
 #if CONFIG_MMCONF_SUPPORT
-void pci_mmio_rawwrite_config8(device_t_raw dev, unsigned where, u8 value)
+static void pci_mmio_rawwrite_config8(device_t_raw dev, unsigned where, u8 value)
 {
 	unsigned addr;
 	addr = dev | where;
@@ -153,7 +156,7 @@ void pci_mmio_rawwrite_config8(device_t_raw dev, unsigned where, u8 value)
 }
 #endif
 
-void pci_rawwrite_config8(device_t_raw dev, unsigned where, u8 value)
+static void pci_rawwrite_config8(device_t_raw dev, unsigned where, u8 value)
 {
 #if CONFIG_MMCONF_SUPPORT
 	pci_mmio_rawwrite_config8(dev, where, value);
@@ -162,7 +165,7 @@ void pci_rawwrite_config8(device_t_raw dev, unsigned where, u8 value)
 #endif
 }
 
-void pci_io_rawwrite_config16(device_t_raw dev, unsigned where, u16 value)
+static void pci_io_rawwrite_config16(device_t_raw dev, unsigned where, u16 value)
 {
 	unsigned addr;
 #if CONFIG_PCI_IO_CFG_EXT == 0
@@ -175,7 +178,7 @@ void pci_io_rawwrite_config16(device_t_raw dev, unsigned where, u16 value)
 }
 
 #if CONFIG_MMCONF_SUPPORT
-void pci_mmio_rawwrite_config16(device_t_raw dev, unsigned where,
+static void pci_mmio_rawwrite_config16(device_t_raw dev, unsigned where,
 				u16 value)
 {
 	unsigned addr;
@@ -184,7 +187,7 @@ void pci_mmio_rawwrite_config16(device_t_raw dev, unsigned where,
 }
 #endif
 
-void pci_rawwrite_config16(device_t_raw dev, unsigned where, u16 value)
+static void pci_rawwrite_config16(device_t_raw dev, unsigned where, u16 value)
 {
 #if CONFIG_MMCONF_SUPPORT
 	pci_mmio_rawwrite_config16(dev, where, value);
@@ -193,7 +196,7 @@ void pci_rawwrite_config16(device_t_raw dev, unsigned where, u16 value)
 #endif
 }
 
-void pci_io_rawwrite_config32(device_t_raw dev, unsigned where, u32 value)
+static void pci_io_rawwrite_config32(device_t_raw dev, unsigned where, u32 value)
 {
 	unsigned addr;
 #if CONFIG_PCI_IO_CFG_EXT == 0
@@ -206,8 +209,7 @@ void pci_io_rawwrite_config32(device_t_raw dev, unsigned where, u32 value)
 }
 
 #if CONFIG_MMCONF_SUPPORT
-void pci_mmio_rawwrite_config32(device_t_raw dev, unsigned where,
-				u32 value)
+static void pci_mmio_rawwrite_config32(device_t_raw dev, unsigned where, u32 value)
 {
 	unsigned addr;
 	addr = dev | where;
@@ -215,7 +217,7 @@ void pci_mmio_rawwrite_config32(device_t_raw dev, unsigned where,
 }
 #endif
 
-void pci_rawwrite_config32(device_t_raw dev, unsigned where, u32 value)
+static void pci_rawwrite_config32(device_t_raw dev, unsigned where, u32 value)
 {
 #if CONFIG_MMCONF_SUPPORT
 	pci_mmio_rawwrite_config32(dev, where, value);
@@ -224,7 +226,7 @@ void pci_rawwrite_config32(device_t_raw dev, unsigned where, u32 value)
 #endif
 }
 
-void pci_rawmodify_config8(device_t_raw dev, unsigned where, u8 orval, u8 mask)
+static void pci_rawmodify_config8(device_t_raw dev, unsigned where, u8 orval, u8 mask)
 {
 	u8 data = pci_rawread_config8(dev, where);
 	data &= (~mask);
@@ -232,7 +234,7 @@ void pci_rawmodify_config8(device_t_raw dev, unsigned where, u8 orval, u8 mask)
 	pci_rawwrite_config8(dev, where, data);
 }
 
-void pci_rawmodify_config16(device_t_raw dev, unsigned where, u16 orval, u16 mask)
+static void pci_rawmodify_config16(device_t_raw dev, unsigned where, u16 orval, u16 mask)
 {
 	u16 data = pci_rawread_config16(dev, where);
 	data &= (~mask);
@@ -240,7 +242,7 @@ void pci_rawmodify_config16(device_t_raw dev, unsigned where, u16 orval, u16 mas
 	pci_rawwrite_config16(dev, where, data);
 }
 
-void pci_rawmodify_config32(device_t_raw dev, unsigned where, u32 orval, u32 mask)
+static void pci_rawmodify_config32(device_t_raw dev, unsigned where, u32 orval, u32 mask)
 {
 	u32 data = pci_rawread_config32(dev, where);
 	data &= (~mask);
@@ -248,7 +250,7 @@ void pci_rawmodify_config32(device_t_raw dev, unsigned where, u32 orval, u32 mas
 	pci_rawwrite_config32(dev, where, data);
 }
 
-void io_rawmodify_config8(u16 where, u8 orval, u8 mask)
+static void io_rawmodify_config8(u16 where, u8 orval, u8 mask)
 {
 	u8 data = inb(where);
 	data &= (~mask);
@@ -256,8 +258,8 @@ void io_rawmodify_config8(u16 where, u8 orval, u8 mask)
 	outb(data, where);
 }
 
-void via_pci_inittable(u8 chipversion,
-		       struct VIA_PCI_REG_INIT_TABLE *initdata)
+static void via_pci_inittable(u8 chipversion,
+		       const struct VIA_PCI_REG_INIT_TABLE *initdata)
 {
 	u8 i = 0;
 	device_t_raw devbxdxfx;
diff --git a/src/northbridge/via/vx800/uma_ram_setting.c b/src/northbridge/via/vx800/uma_ram_setting.c
index 71379e7ec3..72420981ff 100644
--- a/src/northbridge/via/vx800/uma_ram_setting.c
+++ b/src/northbridge/via/vx800/uma_ram_setting.c
@@ -71,7 +71,7 @@ void SetUMARam(void)
 	u8 ramregs[] = { 0x43, 0x42, 0x41, 0x40 };
 	device_t vga_dev = PCI_DEV(0, 1, 0), d0f0_dev = PCI_DEV(0, 0, 0);
 	u8 ByteVal, temp;
-	UMARAM *pUMARamTable;
+	const UMARAM *pUMARamTable;
 	u16 UmaSize;
 	u8 SLD0F3Val, SLD1F0Val, VgaPortVal;
 	u32 RamSize, SLBase, Tmp;
diff --git a/src/northbridge/via/vx800/vx800_early_smbus.c b/src/northbridge/via/vx800/vx800_early_smbus.c
index 93b1461e9a..53ede31cf8 100644
--- a/src/northbridge/via/vx800/vx800_early_smbus.c
+++ b/src/northbridge/via/vx800/vx800_early_smbus.c
@@ -244,14 +244,14 @@ static void enable_smbus(void)
  *       be created just for it. If some other chip needs/wants it, we can
  *       worry about it then.
  *
- * @param ctrl The memory controller and SMBus addresses.
+ * @param mem_ctrl The memory controller and SMBus addresses.
  */
-void smbus_fixup(const struct mem_controller *ctrl)
+static void smbus_fixup(const struct mem_controller *mem_ctrl)
 {
 	int i, ram_slots, current_slot = 0;
 	u8 result = 0;
 
-	ram_slots = ARRAY_SIZE(ctrl->channel0);
+	ram_slots = ARRAY_SIZE(mem_ctrl->channel0);
 	if (!ram_slots) {
 		print_err("smbus_fixup() thinks there are no RAM slots!\n");
 		return;
@@ -272,7 +272,7 @@ void smbus_fixup(const struct mem_controller *ctrl)
 		if (current_slot > ram_slots)
 			current_slot = 0;
 
-		result = get_spd_data(ctrl->channel0[current_slot],
+		result = get_spd_data(mem_ctrl->channel0[current_slot],
 				      SPD_MEMORY_TYPE);
 		current_slot++;
 		PRINT_DEBUG(".");
diff --git a/src/southbridge/via/k8t890/k8t890_early_car.c b/src/southbridge/via/k8t890/k8t890_early_car.c
index a33d6cb5f9..7c6a0ba16d 100644
--- a/src/southbridge/via/k8t890/k8t890_early_car.c
+++ b/src/southbridge/via/k8t890/k8t890_early_car.c
@@ -34,7 +34,7 @@
 
 
 /* AMD K8 LDT0, LDT1, LDT2 Link Control Registers */
-static ldtreg[3] = {0x86, 0xa6, 0xc6};
+static u8 ldtreg[3] = {0x86, 0xa6, 0xc6};
 
 /* This functions sets KT890 link frequency and width to same values as
  * it has been setup on K8 side, by AMD NB init.