diff --git a/src/mainboard/google/brya/Kconfig.name b/src/mainboard/google/brya/Kconfig.name index 7b980e7684..087837f00b 100644 --- a/src/mainboard/google/brya/Kconfig.name +++ b/src/mainboard/google/brya/Kconfig.name @@ -331,3 +331,4 @@ config BOARD_GOOGLE_OMNIGUL select BOARD_GOOGLE_BASEBOARD_BRYA select SOC_INTEL_RAPTORLAKE select USE_UNIFIED_AP_FIRMWARE_FOR_UFS_AND_NON_UFS + select DRIVERS_INTEL_ISH diff --git a/src/mainboard/google/brya/variants/omnigul/overridetree.cb b/src/mainboard/google/brya/variants/omnigul/overridetree.cb index 4f2c04a57a..53f3feacd6 100644 --- a/src/mainboard/google/brya/variants/omnigul/overridetree.cb +++ b/src/mainboard/google/brya/variants/omnigul/overridetree.cb @@ -1,6 +1,212 @@ chip soc/intel/alderlake - device domain 0 on - end + register "sagv" = "SaGv_Enabled" + register "serial_io_i2c_mode" = "{ + [PchSerialIoIndexI2C0] = PchSerialIoPci, + [PchSerialIoIndexI2C1] = PchSerialIoPci, + [PchSerialIoIndexI2C2] = PchSerialIoDisabled, + [PchSerialIoIndexI2C3] = PchSerialIoPci, + [PchSerialIoIndexI2C4] = PchSerialIoDisabled, + [PchSerialIoIndexI2C5] = PchSerialIoPci, + }" + + # SOC Aux orientation override: + # This is a bitfield that corresponds to up to 4 TCSS ports. + # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2. + # TcssAuxOri = 0101b + # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports + # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the + # motherboard to USBC connector + register "tcss_aux_ori" = "1" + register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" + + register "usb2_ports[2]" = "USB2_PORT_EMPTY" # Disable USB2 Port 2 + register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Disable USB2 Port 3 + register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Disable USB2 Port 4 + register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Disable USB2 Port 6 + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port A0 + register "usb2_ports[8]" = "USB2_PORT_EMPTY" # Disable USB2 Port 8 + + register "usb3_ports[0]" = "USB3_PORT_EMPTY" # Disable USB3 Port 0 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A MLB port + register "usb3_ports[2]" = "USB3_PORT_EMPTY" # Disable USB3 Port 2 + register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Disable USB3 Port 3 + + register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC0)" # Type C port C0 + register "tcss_ports[1]" = "TCSS_PORT_EMPTY" # Disable Port1 + register "tcss_ports[2]" = "TCSS_PORT_DEFAULT(OC1)" # Type C port C1 + register "tcss_ports[3]" = "TCSS_PORT_EMPTY" # Disable Port3 + + # FIVR configurations for brya are disabled since the board doesn't have V1p05 and Vnn + # bypass rails implemented. + register "ext_fivr_settings" = "{ + .configure_ext_fivr = 1, + }" + + device domain 0 on + device ref i2c0 on + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Realtek RT5682"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_H0)" + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + chip drivers/generic/alc1015 + register "hid" = ""RTL1019"" + register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + device generic 1 on end + end + end #I2C0 + device ref i2c1 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" + device i2c 50 on end + end + end #I2C1 + device ref i2c3 on + chip drivers/i2c/hid + register "generic.hid" = ""GTCH7503"" + register "generic.desc" = ""G2TOUCH Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "50" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 40 on end + end + end #I2C3 + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "detect" = "1" + device i2c 15 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""SYNA0000"" + register "generic.cid" = ""ACPI0C50"" + register "generic.desc" = ""Synaptics Touchpad"" + register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "generic.wake" = "GPE0_DW2_14" + register "generic.detect" = "1" + register "hid_desc_reg_offset" = "0x20" + device i2c 2c on end + end + end #I2C5 + device ref pcie_rp8 off end + device ref pcie_rp9 off end + device ref ish on + chip drivers/intel/ish + register "add_acpi_dma_property" = "true" + device generic 0 on end + end + end + device ref ufs on end + device ref tbt_pcie_rp0 off end + device ref tbt_pcie_rp1 off end + device ref tbt_pcie_rp2 off end + device ref tcss_dma0 off end + device ref tcss_dma1 off end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[2] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port1 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port2 as usb2_port + use tcss_usb3_port3 as usb3_port + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 1))" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref tcss_usb3_port3 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 1))" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))" + device ref usb2_port8 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))" + device ref usb3_port1 on end + end + end + end + end + end end