diff --git a/src/mainboard/google/brya/variants/joxer/gpio.c b/src/mainboard/google/brya/variants/joxer/gpio.c
index ec7ef795f9..b1dcd4a83b 100644
--- a/src/mainboard/google/brya/variants/joxer/gpio.c
+++ b/src/mainboard/google/brya/variants/joxer/gpio.c
@@ -17,6 +17,9 @@ static const struct pad_config override_gpio_table[] = {
 	/* B6  : SOC_I2C_SUB_SCL ==> NC */
 	PAD_NC_LOCK(GPP_B6, NONE, LOCK_CONFIG),
 
+	/* C1  : SMBDATA ==> TCHSCR_RST_L */
+	PAD_CFG_GPO(GPP_C1, 1, DEEP),
+
 	/* D3  : WCAM_RST_L ==> NC */
 	PAD_NC_LOCK(GPP_D3, NONE, LOCK_CONFIG),
 	/* D15 : EN_PP2800_WCAM_X ==> NC */
@@ -78,6 +81,11 @@ static const struct pad_config early_gpio_table[] = {
 };
 
 static const struct pad_config romstage_gpio_table[] = {
+	/* Enable touchscreen, hold in reset */
+	/* C0  : SMBCLK ==> EN_PP3300_TCHSCR_X */
+	PAD_CFG_GPO(GPP_C0, 1, DEEP),
+	/* C1  : SMBDATA ==> TCHSCR_RST_L */
+	PAD_CFG_GPO(GPP_C1, 0, DEEP),
 	/* H12 : UART0_RTS# ==> SD_PERST_L */
 	PAD_CFG_GPO(GPP_H12, 1, DEEP),
 	/* H20 : IMGCLKOUT1 ==> WLAN_PERST_L */
diff --git a/src/mainboard/google/brya/variants/joxer/overridetree.cb b/src/mainboard/google/brya/variants/joxer/overridetree.cb
index e591b13dbd..dbfeb6d208 100644
--- a/src/mainboard/google/brya/variants/joxer/overridetree.cb
+++ b/src/mainboard/google/brya/variants/joxer/overridetree.cb
@@ -133,11 +133,59 @@ chip soc/intel/alderlake
 			end
 		end
 		device ref i2c1 on
+			chip drivers/i2c/generic
+				register "hid" = ""ELAN0001""
+				register "desc" = ""ELAN Touchscreen""
+				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+				register "detect" = "1"
+				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+				register "reset_delay_ms" = "20"
+				register "reset_off_delay_ms" = "2"
+				register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+				register "stop_delay_ms" = "280"
+				register "stop_off_delay_ms" = "2"
+				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+				register "enable_delay_ms" = "1"
+				register "has_power_resource" = "1"
+				device i2c 10 on end
+			end
+			chip drivers/i2c/hid
+				register "generic.hid" = ""ELAN2513""
+				register "generic.desc" = ""ELAN Touchscreen""
+				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+				register "generic.detect" = "1"
+				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+				register "generic.reset_delay_ms" = "20"
+				register "generic.reset_off_delay_ms" = "2"
+				register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+				register "generic.stop_delay_ms" = "280"
+				register "generic.stop_off_delay_ms" = "2"
+				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+				register "generic.enable_delay_ms" = "1"
+				register "generic.has_power_resource" = "1"
+				register "hid_desc_reg_offset" = "0x01"
+				device i2c 15 on end
+			end
+			chip drivers/i2c/hid
+				register "generic.hid" = ""GTCH7503""
+				register "generic.desc" = ""G2TOUCH Touchscreen""
+				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+				register "generic.detect" = "1"
+				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+				register "generic.reset_delay_ms" = "50"
+				register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+				register "generic.stop_delay_ms" = "30"
+				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+				register "generic.enable_delay_ms" = "1"
+				register "generic.has_power_resource" = "1"
+				register "hid_desc_reg_offset" = "0x01"
+				device i2c 40 on end
+			end
 			chip drivers/i2c/hid
 				register "generic.hid" = ""GDIX0000""
 				register "generic.desc" = ""Goodix Touchscreen""
 				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
-				register "generic.probed" = "1"
+				register "generic.detect" = "1"
 				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
 				register "generic.enable_delay_ms" = "20"
 				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"