From b0d3695d38bf7300abe58959f309b90845580f69 Mon Sep 17 00:00:00 2001 From: Angel Pons Date: Sun, 1 Dec 2019 22:10:51 +0100 Subject: [PATCH] soc/intel/bsw/gpio.h: Drop unused values Most of these are leftovers from the initial copy from Baytrail. Change-Id: I1c437f34902400022ac6a5e95ff6168545ca557f Signed-off-by: Angel Pons Reviewed-on: https://review.coreboot.org/c/coreboot/+/37405 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber --- src/soc/intel/braswell/include/soc/gpio.h | 96 ----------------------- 1 file changed, 96 deletions(-) diff --git a/src/soc/intel/braswell/include/soc/gpio.h b/src/soc/intel/braswell/include/soc/gpio.h index 24318c5e5e..db8e2a345c 100644 --- a/src/soc/intel/braswell/include/soc/gpio.h +++ b/src/soc/intel/braswell/include/soc/gpio.h @@ -128,16 +128,8 @@ /* Pad register offset */ #define PAD_CONF0_REG 0x0 #define PAD_CONF1_REG 0x4 -#define PAD_VAL_REG 0x8 - -/* Some banks have no legacy GPIO interface */ -#define GP_LEGACY_BASE_NONE 0xFFFF /* Number of GPIOs in each bank */ -#define GPNCORE_COUNT 27 -#define GPSCORE_COUNT 102 -#define GPSSUS_COUNT 44 - #define GP_SOUTHWEST_COUNT 56 #define GP_NORTH_COUNT 59 #define GP_EAST_COUNT 24 @@ -146,8 +138,6 @@ /* General */ #define GPIO_REGS_SIZE 8 #define NA 0 -#define LOW 0 -#define HIGH 1 #define MASK_WAKE 0 #define UNMASK_WAKE 1 #define GPE_CAPABLE 1 @@ -354,13 +344,7 @@ #define GPIO_END \ { .pad_conf0 = GPIO_LIST_END } -/* 16 DirectIRQs per supported bank */ -#define GPIO_MAX_DIRQS 16 - -#define GPIO_NONE 255 - /* Functions / defines for changing GPIOs in romstage */ -/* SCORE Pad definitions. */ #define UART_RXD_PAD 82 #define UART_TXD_PAD 83 #define PCU_SMB_CLK_PAD 88 @@ -374,7 +358,6 @@ struct soc_gpio_map { u32 pad_conf0; u32 pad_conf1; - u32 pad_val; u32 gpe; u32 int_mask:1; u32 wake_mask:1; @@ -393,38 +376,11 @@ struct soc_gpio_config { struct gpio_bank { const int gpio_count; const u8 *gpio_to_pad; - const int legacy_base; const unsigned long pad_base; const u8 has_gpe_en:1; const u8 has_wake_en:1; }; -typedef enum { - NATIVE = 0xff, - GPIO = 0, /* Native, no need to set PAD_VALUE */ - GPO = 1, /* GPI, input only in PAD_VALUE */ - GPI = 2, /* GPO, output only in PAD_VALUE */ - HI_Z = 3, - NA_GPO = 0, -} gpio_en_t; - -typedef enum { - LO = 0, - HI = 1, -} gpo_d4_t; - -typedef enum { - F0 = 0, - F1 = 1, - F2 = 2, - F3 = 3 -} gpio_func_num_t; - -typedef enum { - _CAP = 1, - _NOT_CAP = 0 -} int_capable_t; - typedef enum { P_NONE = 0, /* Pull None */ P_20K_L = 1, /* Pull Down 20K */ @@ -435,42 +391,6 @@ typedef enum { P_1K_H = 12 /* Pull Up 1K */ } pull_type_t; -typedef enum { - DISABLE = 0, /* Disable */ - ENABLE = 1, /* Enable */ -} park_mode_enb_t; - -typedef enum { - VOLT_3_3 = 0, /* Working on 3.3 Volts */ - VOLT_1_8 = 1, /* Working on 1.8 Volts */ -} voltage_t; - -typedef enum { - DISABLE_HS = 0, /* Disable high speed mode */ - ENABLE_HS = 1, /* Enable high speed mode */ -} hs_mode_t; - -typedef enum { - PULL_UP = 0, /* On Die Termination Up */ - PULL_DOWN = 1, /* On Die Termination Down */ -} odt_up_dn_t; - -typedef enum { - DISABLE_OD = 0, /* On Die Termination Disable */ - ENABLE_OD = 1, /* On Die Termination Enable */ -} odt_en_t; - -typedef enum { - ONE_BIT = 1, - TWO_BIT = 3, - THREE_BIT = 7, - FOUR_BIT = 15, - FIVE_BIT = 31, - SIX_BIT = 63, - SEVEN_BIT = 127, - EIGHT_BIT = 255 -} bit_t; - typedef enum { M0 = 0, M1, @@ -557,22 +477,6 @@ typedef enum { void setup_soc_gpios(struct soc_gpio_config *config, u8 enable_xdp_tap); struct soc_gpio_config *mainboard_get_gpios(void); -static inline void ncore_select_func(int pad, int func) -{ - -} - -/* These functions require that the input pad be configured as an input GPIO */ - -static inline int ssus_get_gpio(int pad) -{ - return 0; -} - -static inline void ssus_disable_internal_pull(int pad) -{ -} - typedef int gpio_t; int get_gpio(int community_base, int pad0_offset);