Some fixes for the BCOM WinNET100, mostly in Config.lb:

- Add missing entry for the NIC:

     device pci 0f.0 on end           # Ethernet (onboard)

 - Drop the following lines:

     register "com1" = "{115200}"
     register "com2" = "{38400}"

   Those entries hardcode the BAUD rate (as far as I can tell, please
   correct me if I'm wrong). We don't want that -- instead the config option
   TTYS0_BAUD in Options.lb should be used(?) I verified that dropping those
   lines will not break serial output (COM1, 115200, 8n1).

 - Enable IDE (PCI device 00:12.2) and add the following register lines
   to tell the CS5530 code to actually enable IDE channel 0:

      register "ide0_enable" = "1"
      register "ide1_enable" = "0"     # Not available/needed on this board

   Tested with a 2.5" hard drive and FILO, works fine.

 - Enable USB (PCI device 00:13.0), not sure why it was commented.

 - Enable COM2 as it's used by the smartcard reader.

 - Add CONFIG_COMPRESSED_PAYLOAD_LZMA to Options.lb, in order to fix
   abuild for this board.

 - Add some more comments.

Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>



git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2896 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

src/mainboard/bcom/winnet100/Config.lb

@@ -79,55 +79,59 @@ mainboardinit ./auto.inc
 dir /pc80
 config chip.h
 
-chip northbridge/amd/gx1
-  device pci_domain 0 on
-    device pci 0.0 on end
-      chip southbridge/amd/cs5530
-        device pci 12.0 on
-          chip superio/nsc/pc97317
-            device pnp 2e.0 on		# PS/2 keyboard
-              io 0x60 = 0x60
-              io 0x62 = 0x64
-              irq 0x70 = 1
-            end
-            device pnp 2e.1 on		# PS/2 mouse
-              irq 0x70 = 12
-            end
-            device pnp 2e.2 on		# RTC
-              io 0x60 = 0x70
-              irq 0x70 = 8
-            end
-            device pnp 2e.3 off		# Floppy
-            end
-            device pnp 2e.4 on		# Parallel port
-              io 0x60 = 0x378
-              irq 0x70 = 7
-            end
-            device pnp 2e.5 off		# COM2
-              io 0x60 = 0x2f8
-              irq 0x70 = 3
-            end
-            device pnp 2e.6 on		# COM1
-              io 0x60 = 0x3f8
-              irq 0x70 = 4
-            end
-            device pnp 2e.7 on		# GPIO
-              io 0x60 = 0xe0
-            end
-            device pnp 2e.8 on		# Power management
-               io 0x60 = 0xe800
-            end
-            register "com1" = "{115200}"
-            register "com2" = "{38400}"
+chip northbridge/amd/gx1		# Northbridge
+  device pci_domain 0 on		# PCI domain
+    device pci 0.0 on end		# Host bridge
+    chip southbridge/amd/cs5530		# Southbridge
+      device pci 0f.0 on end		# Ethernet (onboard)
+      device pci 12.0 on		# ISA bridge
+        chip superio/nsc/pc97317	# Super I/O
+          device pnp 2e.0 on		# PS/2 keyboard
+            io 0x60 = 0x60
+            io 0x62 = 0x64
+            irq 0x70 = 1
           end
-        device pci 12.1 off end		# SMI
-        device pci 12.2 off end		# IDE
-        device pci 12.3 on end		# Audio
-        device pci 12.4 on end		# VGA
-        # device pci 13.0 on end	# USB
+          device pnp 2e.1 on		# PS/2 mouse
+            irq 0x70 = 12
+          end
+          device pnp 2e.2 on		# RTC, Advanced power control (APC)
+            io 0x60 = 0x70
+            irq 0x70 = 8
+          end
+          device pnp 2e.3 off		# Floppy (N/A on this board)
+            io 0x60 = 0x3f0
+            irq 0x70 = 6
+            drq 0x74 = 2
+          end
+          device pnp 2e.4 on		# Parallel port
+            io 0x60 = 0x378
+            irq 0x70 = 7
+          end
+          device pnp 2e.5 on		# COM2 (used for smartcard reader)
+            io 0x60 = 0x2f8
+            irq 0x70 = 3
+          end
+          device pnp 2e.6 on		# COM1
+            io 0x60 = 0x3f8
+            irq 0x70 = 4
+          end
+          device pnp 2e.7 on		# GPIO
+            io 0x60 = 0xe0
+          end
+          device pnp 2e.8 on		# Power management
+            io 0x60 = 0xe8
+          end
+        end
       end
+      device pci 12.1 off end		# SMI
+      device pci 12.2 on end		# IDE
+      device pci 12.3 on end		# Audio
+      device pci 12.4 on end		# VGA (onboard)
+      device pci 13.0 on end		# USB
+      register "ide0_enable" = "1"
+      register "ide1_enable" = "0"	# Not available/needed on this board
     end
   end
-  chip cpu/amd/model_gx1
+  chip cpu/amd/model_gx1		# CPU
   end
 end

src/mainboard/bcom/winnet100/Options.lb

@@ -56,6 +56,7 @@ uses CONFIG_CONSOLE_SERIAL8250
 uses TTYS0_BAUD
 uses TTYS0_BASE
 uses TTYS0_LCS
+uses CONFIG_COMPRESSED_PAYLOAD_LZMA
 uses CONFIG_UDELAY_TSC
 uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
 uses CONFIG_VIDEO_MB