mb/google/nissa/var/gothrax: Initialise overridetree

Add an initial overridetree for gothrax based on the schematic.

BUG=b:274707912
BRANCH=None
TEST=emerge-nissa coreboot

Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: Idfd9788a75f9c342f85d6e1a3d54327d64797dd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76013
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit is contained in:
Yunlong Jia 2023-06-21 09:56:25 +00:00 committed by Subrata Banik
parent 92904bcdff
commit e40cdd5ae4
2 changed files with 424 additions and 2 deletions

View File

@ -26,6 +26,9 @@ static const struct pad_config override_gpio_table[] = {
/* B6 : SOC_I2C_SUB_SCL */
PAD_NC_LOCK(GPP_B6, NONE, LOCK_CONFIG),
/* C1 : SMBDATA ==> TCHSCR_RST_L */
PAD_CFG_GPO(GPP_C1, 1, DEEP),
/* D3 : WCAM_RST_L */
PAD_NC_LOCK(GPP_D3, NONE, LOCK_CONFIG),
/* D15 : EN_PP2800_WCAM_X */
@ -69,6 +72,11 @@ static const struct pad_config early_gpio_table[] = {
};
static const struct pad_config romstage_gpio_table[] = {
/* Enable touchscreen, hold in reset */
/* C0 : SMBCLK ==> EN_PP3300_TCHSCR_X */
PAD_CFG_GPO(GPP_C0, 1, DEEP),
/* C1 : SMBDATA ==> TCHSCR_RST_L */
PAD_CFG_GPO(GPP_C1, 0, DEEP),
/* H12 : UART0_RTS# ==> SD_PERST_L */
PAD_CFG_GPO(GPP_H12, 1, DEEP),
/* H20 : IMGCLKOUT1 ==> WLAN_PERST_L */

View File

@ -1,4 +1,28 @@
fw_config
field DB_USB 0 1
option DB_NONE 0
option DB_C_A 1
option DB_C_LTE 2
end
field THERMAL_SOLUTION 2
option THERMAL_SOLUTION_PASSIVE 0
option THERMAL_SOLUTION_ACTIVE 1
end
field WLAN 3 4
option WLAN_MT7921_AZUREWAVE 0
option WLAN_AX211_Intel 1
end
field AUDIO 5 6
option AUDIO_ALC1019_ALC5682IVS 0
end
field STYLUS 7
option STYLUS_ABSENT 0
option STYLUS_PRESENT 1
end
end
chip soc/intel/alderlake
register "sagv" = "SaGv_Enabled"
# EMMC Tx CMD Delay
# Refer to EDS-Vol2-42.3.7.
@ -45,7 +69,397 @@ chip soc/intel/alderlake
# [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39.
register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x01515"
device domain 0 on
end
# Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC.
# Bit 2 - C1 has a redriver which does SBU muxing.
# Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1.
register "tcss_aux_ori" = "5"
register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}"
# Configure external V1P05/Vnn/VnnSx Rails
register "ext_fivr_settings" = "{
.configure_ext_fivr = 1,
.v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0,
.vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
.vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX,
.v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL,
.vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE,
.v1p05_voltage_mv = 1050,
.vnn_voltage_mv = 780,
.vnn_sx_voltage_mv = 1050,
.v1p05_icc_max_ma = 500,
.vnn_icc_max_ma = 500,
}"
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| I2C0 | TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| I2C1 | Touchscreen |
#| I2C2 | Sub-board(PSensor)/WCAM |
#| I2C3 | Audio |
#| I2C5 | Trackpad |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.i2c[0] = {
.early_init = 1,
.speed = I2C_SPEED_FAST_PLUS,
.speed_config[0] = {
.speed = I2C_SPEED_FAST_PLUS,
.scl_lcnt = 55,
.scl_hcnt = 30,
.sda_hold = 7,
}
},
.i2c[1] = {
.speed = I2C_SPEED_FAST,
.speed_config[0] = {
.speed = I2C_SPEED_FAST,
.scl_lcnt = 160,
.scl_hcnt = 79,
.sda_hold = 7,
}
},
.i2c[2] = {
.speed = I2C_SPEED_FAST,
.speed_config[0] = {
.speed = I2C_SPEED_FAST,
.scl_lcnt = 157,
.scl_hcnt = 79,
.sda_hold = 7,
}
},
.i2c[3] = {
.speed = I2C_SPEED_FAST,
.speed_config[0] = {
.speed = I2C_SPEED_FAST,
.scl_lcnt = 157,
.scl_hcnt = 79,
.sda_hold = 7,
}
},
.i2c[5] = {
.speed = I2C_SPEED_FAST,
.speed_config[0] = {
.speed = I2C_SPEED_FAST,
.scl_lcnt = 152,
.scl_hcnt = 79,
.sda_hold = 7,
}
},
}"
device domain 0 on
device ref dtt on
chip drivers/intel/dptf
## sensor information
register "options.tsr[0].desc" = ""Memory""
register "options.tsr[1].desc" = ""Charger""
register "options.tsr[2].desc" = ""Ambient""
# TODO: below values are initial reference values only
## Passive Policy
register "policies.passive" = "{
[0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
[2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
[3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000),
}"
## Critical Policy
register "policies.critical" = "{
[0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
}"
register "controls.power_limits" = "{
.pl1 = {
.min_power = 3000,
.max_power = 6000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 200
},
.pl2 = {
.min_power = 25000,
.max_power = 25000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 1000
}
}"
## Charger Performance Control (Control, mA)
register "controls.charger_perf" = "{
[0] = { 255, 1700 },
[1] = { 24, 1500 },
[2] = { 16, 1000 },
[3] = { 8, 500 }
}"
device generic 0 on end
end
end
device ref i2c1 on
chip drivers/i2c/generic
register "hid" = ""ELAN0001""
register "desc" = ""ELAN Touchscreen""
register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
register "detect" = "1"
register "reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
register "reset_delay_ms" = "20"
register "enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
register "enable_delay_ms" = "1"
register "has_power_resource" = "1"
device i2c 0x10 on end
end
end
device ref i2c2 on
chip drivers/i2c/sx9324
register "desc" = ""SAR2 Proximity Sensor""
register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)"
register "speed" = "I2C_SPEED_FAST"
register "uid" = "2"
register "reg_gnrl_ctrl0" = "0x16"
register "reg_gnrl_ctrl1" = "0x21"
register "reg_afe_ctrl0" = "0x00"
register "reg_afe_ctrl1" = "0x10"
register "reg_afe_ctrl2" = "0x00"
register "reg_afe_ctrl3" = "0x00"
register "reg_afe_ctrl4" = "0x07"
register "reg_afe_ctrl5" = "0x00"
register "reg_afe_ctrl6" = "0x00"
register "reg_afe_ctrl7" = "0x07"
register "reg_afe_ctrl8" = "0x12"
register "reg_afe_ctrl9" = "0x0f"
register "reg_prox_ctrl0" = "0x12"
register "reg_prox_ctrl1" = "0x12"
register "reg_prox_ctrl2" = "0x90"
register "reg_prox_ctrl3" = "0x60"
register "reg_prox_ctrl4" = "0x0c"
register "reg_prox_ctrl5" = "0x12"
register "reg_prox_ctrl6" = "0x3c"
register "reg_prox_ctrl7" = "0x58"
register "reg_adv_ctrl0" = "0x00"
register "reg_adv_ctrl1" = "0x00"
register "reg_adv_ctrl2" = "0x00"
register "reg_adv_ctrl3" = "0x00"
register "reg_adv_ctrl4" = "0x00"
register "reg_adv_ctrl5" = "0x05"
register "reg_adv_ctrl6" = "0x00"
register "reg_adv_ctrl7" = "0x00"
register "reg_adv_ctrl8" = "0x00"
register "reg_adv_ctrl9" = "0x00"
register "reg_adv_ctrl10" = "0x5c"
register "reg_adv_ctrl11" = "0x52"
register "reg_adv_ctrl12" = "0xb5"
register "reg_adv_ctrl13" = "0x00"
register "reg_adv_ctrl14" = "0x80"
register "reg_adv_ctrl15" = "0x0c"
register "reg_adv_ctrl16" = "0x38"
register "reg_adv_ctrl17" = "0x56"
register "reg_adv_ctrl18" = "0x33"
register "reg_adv_ctrl19" = "0xf0"
register "reg_adv_ctrl20" = "0xf0"
device i2c 28 on end
end
end
device ref i2c3 on
chip drivers/i2c/generic
register "hid" = ""RTL5682""
register "name" = ""RT58""
register "desc" = ""Headset Codec""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
# Set the jd_src to RT5668_JD1 for jack detection
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on end
end
chip drivers/generic/alc1015
register "hid" = ""RTL1019""
register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
device generic 0 on end
end
end
device ref i2c5 on
chip drivers/i2c/hid
register "generic.hid" = ""PNP0C50""
register "generic.desc" = ""PIXART Touchpad""
register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
register "generic.wake" = "GPE0_DW2_14"
register "generic.detect" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 15 on end
end
end
device ref pcie_rp4 on
# PCIe 4 WLAN
register "pch_pcie_rp[PCH_RP(4)]" = "{
.clk_src = 2,
.clk_req = 2,
.flags = PCIE_RP_LTR | PCIE_RP_AER,
}"
chip drivers/wifi/generic
register "wake" = "GPE0_DW1_03"
register "add_acpi_dma_property" = "true"
device pci 00.0 on end
end
end
device ref pcie_rp7 on
# Enable SD Card PCIe 7 using clk 3
register "pch_pcie_rp[PCH_RP(7)]" = "{
.clk_src = 3,
.clk_req = 3,
.flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
}"
chip soc/intel/common/block/pcie/rtd3
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)"
register "srcclk_pin" = "3"
device generic 0 on end
end
end
device ref pch_espi on
chip ec/google/chromeec
use conn0 as mux_conn[0]
use conn1 as mux_conn[1]
device pnp 0c09.0 on end
end
end
device ref pmc hidden
chip drivers/intel/pmc_mux
device generic 0 on
chip drivers/intel/pmc_mux/conn
use usb2_port1 as usb2_port
use tcss_usb3_port1 as usb3_port
device generic 0 alias conn0 on end
end
chip drivers/intel/pmc_mux/conn
use usb2_port2 as usb2_port
use tcss_usb3_port2 as usb3_port
device generic 1 alias conn1 on end
end
end
end
end
device ref tcss_xhci on
chip drivers/usb/acpi
device ref tcss_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C0 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
device ref tcss_usb3_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C1 (DB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
device ref tcss_usb3_port2 on end
end
end
end
end
device ref xhci on
register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # USB2_A1
register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # WFC
register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN
register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/3 Type A port A1
chip drivers/usb/acpi
device ref xhci_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C0 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
device ref usb2_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C1 (DB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
device ref usb2_port2 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Port A0 (MLB)""
register "type" = "UPC_TYPE_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
device ref usb2_port3 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Port A1 (DB)""
register "type" = "UPC_TYPE_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
device ref usb2_port4 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 WWAN""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb2_port5 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 UFC""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb2_port6 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 WFC""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb2_port7 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
device ref usb2_port8 on end
end
chip drivers/usb/acpi
register "desc" = ""CNVi Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
device ref usb2_port10 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Port A0 (MLB)""
register "type" = "UPC_TYPE_USB3_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
device ref usb3_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Port A1 (DB)""
register "type" = "UPC_TYPE_USB3_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
device ref usb3_port2 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 WWAN""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb3_port3 on end
end
end
end
end
end
end