Add compile-time defaults to some K8 CMOS options in case they're absent in CMOS

This affects the CMOS options iommu, ECC_memory, max_mem_clock,
hw_scrubber, interleave_chip_selects.
If they're absent in cmos.layout, a Kconfig value is used if it exists,
or a hardcoded default otherwise.

[Patrick: I changed the ramstage CMOS handling a bit, and dropped the
reliance of hw_scrubber on ECC RAM, as it has nothing to do with it -
it's the cache that's being scrubbed here.]

Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6380 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

src/cpu/amd/model_fxx/Kconfig

@@ -14,6 +14,10 @@ config SET_FIDVID
 	default n
 	default y if K8_REV_F_SUPPORT
 
+config HW_SCRUBBER
+	bool
+	default n
+
 if SET_FIDVID
 config SET_FIDVID_DEBUG
 	bool

src/cpu/amd/model_fxx/model_fxx_init.c

@@ -264,7 +264,10 @@ static void init_ecc_memory(unsigned node_id)
 
 	/* See if we scrubbing should be enabled */
 	enable_scrubbing = 1;
-	get_option(&enable_scrubbing, "hw_scrubber");
+	if( get_option(&enable_scrubbing, "hw_scrubber") < 0 ) 
+	{
+		enable_scrubbing = CONFIG_HW_SCRUBBER;
+	}
 
 	/* Enable cache scrubbing at the lowest possible rate */
 	if (enable_scrubbing) {

src/northbridge/amd/amdk8/Kconfig

@@ -83,6 +83,10 @@ endif #DIMM_DDR2
 
 endif #K8_REV_F_SUPPORT
 
+config IOMMU
+	bool
+	default y
+
 endif #NORTHBRIDGE_AMD_K8
 
 source src/northbridge/amd/amdk8/root_complex/Kconfig

src/northbridge/amd/amdk8/misc_control.c

@@ -48,7 +48,10 @@ static void mcf3_read_resources(device_t dev)
 	}
 
 	iommu = 1;
-	get_option(&iommu, "iommu");
+	if( get_option(&iommu, "iommu") < 0 ) 
+	{
+		iommu = CONFIG_IOMMU;
+	}
 
 	if (iommu) {
 		/* Add a GART aperture resource */

src/northbridge/amd/amdk8/raminit_f.c

@@ -1107,6 +1107,15 @@ static unsigned long interleave_chip_selects(const struct mem_controller *ctrl,
 	/* See if all of the memory chip selects are the same size
 	 * and if so count them.
 	 */
+#if defined(CMOS_VSTART_interleave_chip_selects)
+	if (read_option(CMOS_VSTART_interleave_chip_selects, CMOS_VLEN_interleave_chip_selects, 1) == 0)
+		return 0;
+#else
+#if !defined(CONFIG_INTERLEAVE_CHIP_SELECTS) || (CONFIG_INTERLEAVE_CHIP_SELECTS == 0)
+	return 0;
+#endif
+#endif
+
 	chip_selects = 0;
 	common_size = 0;
 	common_cs_mode = 0xff;
@@ -1279,15 +1288,10 @@ static void order_dimms(const struct mem_controller *ctrl,
 {
 	unsigned long tom_k, base_k;
 
-	if (read_option(CMOS_VSTART_interleave_chip_selects,
+	tom_k = interleave_chip_selects(ctrl, meminfo->is_Width128);
-	    CMOS_VLEN_interleave_chip_selects, 1) != 0) {
-		tom_k = interleave_chip_selects(ctrl, meminfo->is_Width128);
-	} else {
-		printk(BIOS_DEBUG, "Interleaving disabled\n");
-		tom_k = 0;
-	}
 
 	if (!tom_k) {
+		printk(BIOS_DEBUG, "Interleaving disabled\n");
 		tom_k = order_chip_selects(ctrl);
 	}
 
@@ -1801,7 +1805,17 @@ static struct spd_set_memclk_result spd_set_memclk(const struct mem_controller *
 	value = pci_read_config32(ctrl->f3, NORTHBRIDGE_CAP);
 	min_cycle_time = min_cycle_times[(value >> NBCAP_MEMCLK_SHIFT) & NBCAP_MEMCLK_MASK];
 	bios_cycle_time = min_cycle_times[
-		read_option(CMOS_VSTART_max_mem_clock, CMOS_VLEN_max_mem_clock, 0)];
+#ifdef CMOS_VSTART_max_mem_clock
+		read_option(CMOS_VSTART_max_mem_clock, CMOS_VLEN_max_mem_clock, 0)
+#else
+#if defined(CONFIG_MAX_MEM_CLOCK)
+		CONFIG_MAX_MEM_CLOCK
+#else
+		0 // use DDR400 as default
+#endif
+#endif
+	];
+	
 	if (bios_cycle_time > min_cycle_time) {
 		min_cycle_time = bios_cycle_time;
 	}
@@ -2360,14 +2374,21 @@ static void set_ecc(const struct mem_controller *ctrl,
 	if (nbcap & NBCAP_ECC) {
 		dcl |= DCL_DimmEccEn;
 	}
+#ifdef CMOS_VSTART_ECC_memory
 	if (read_option(CMOS_VSTART_ECC_memory, CMOS_VLEN_ECC_memory, 1) == 0) {
 		dcl &= ~DCL_DimmEccEn;
 	}
+#else // CMOS_VSTART_ECC_memory not defined
+#if defined(CONFIG_ECC_MEMORY) && (CONFIG_ECC_MEMORY == 0)
+	dcl &= ~DCL_DimmEccEn;
+#endif
+#endif
 	pci_write_config32(ctrl->f2, DRAM_CONFIG_LOW, dcl);
 
 	meminfo->is_ecc = 1;
 	if (!(dcl & DCL_DimmEccEn)) {
 		meminfo->is_ecc = 0;
+		printk(BIOS_DEBUG, "set_ecc: ECC disabled\n");
 		return; // already disabled the ECC, so don't need to read SPD any more
 	}