mb/google/nissa/var/craaskov: Add overridetree
Add override devicetree based on schematics(ver. 20230714). BUG=b:290248526 BRANCH=firmware-nissa-15217.B TEST=emerge-nissa coreboot Change-Id: Id002282d91dc94b00f5d133203b62ca39d6cae6d Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/76662 Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Derek Huang <derekhuang@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit is contained in:
Rex Chou
Felix Held
parent
9ec479de47
commit
f232b19e56
|
|
@ -1,6 +1,231 @@
|
|||
chip soc/intel/alderlake
|
||||
register "sagv" = "SaGv_Enabled"
|
||||
|
||||
device domain 0 on
|
||||
# Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC.
|
||||
# Bit 2 - C1 has a redriver which does SBU muxing.
|
||||
# Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1.
|
||||
register "tcss_aux_ori" = "1"
|
||||
|
||||
register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
|
||||
|
||||
# Intel Common SoC Config
|
||||
#+-------------------+---------------------------+
|
||||
#| Field | Value |
|
||||
#+-------------------+---------------------------+
|
||||
#| I2C0 | TPM. Early init is |
|
||||
#| | required to set up a BAR |
|
||||
#| | for TPM communication |
|
||||
#| I2C1 | Touchscreen |
|
||||
#| I2C2 | TOF/ALS |
|
||||
#| I2C3 | Audio |
|
||||
#| I2C5 | Trackpad |
|
||||
#+-------------------+---------------------------+
|
||||
register "common_soc_config" = "{
|
||||
.i2c[0] = {
|
||||
.early_init = 1,
|
||||
.speed = I2C_SPEED_FAST_PLUS,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST_PLUS,
|
||||
.scl_lcnt = 55,
|
||||
.scl_hcnt = 30,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
.i2c[1] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.scl_lcnt = 158,
|
||||
.scl_hcnt = 79,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
.i2c[2] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.scl_lcnt = 158,
|
||||
.scl_hcnt = 79,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
.i2c[3] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.scl_lcnt = 158,
|
||||
.scl_hcnt = 79,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
.i2c[5] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.speed_config[0] = {
|
||||
.speed = I2C_SPEED_FAST,
|
||||
.scl_lcnt = 158,
|
||||
.scl_hcnt = 79,
|
||||
.sda_hold = 7,
|
||||
}
|
||||
},
|
||||
}"
|
||||
|
||||
register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2 Port 2
|
||||
register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Disable USB2 Port 5
|
||||
register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Disable USB2 Port 7
|
||||
register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
|
||||
register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
|
||||
|
||||
device domain 0 on
|
||||
device ref i2c1 on
|
||||
chip drivers/i2c/hid
|
||||
register "generic.hid" = ""ELAN9004""
|
||||
register "generic.desc" = ""ELAN Touchscreen""
|
||||
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
|
||||
register "generic.probed" = "1"
|
||||
register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
|
||||
register "generic.reset_delay_ms" = "20"
|
||||
register "generic.reset_off_delay_ms" = "2"
|
||||
register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
|
||||
register "generic.enable_delay_ms" = "1"
|
||||
register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
|
||||
register "generic.stop_delay_ms" = "150"
|
||||
register "generic.stop_off_delay_ms" = "2"
|
||||
register "generic.has_power_resource" = "1"
|
||||
register "hid_desc_reg_offset" = "0x01"
|
||||
device i2c 10 on end
|
||||
end
|
||||
end #I2C1
|
||||
device ref i2c3 on
|
||||
chip drivers/i2c/generic
|
||||
register "hid" = ""10EC5650""
|
||||
register "name" = ""RT58""
|
||||
register "desc" = ""Realtek RT5650""
|
||||
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
|
||||
register "property_count" = "1"
|
||||
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
|
||||
register "property_list[0].name" = ""realtek,jd-mode""
|
||||
register "property_list[0].integer" = "2"
|
||||
device i2c 1a on end
|
||||
end
|
||||
end #I2C3
|
||||
device ref i2c5 on
|
||||
chip drivers/i2c/generic
|
||||
register "hid" = ""ELAN0000""
|
||||
register "desc" = ""ELAN Touchpad""
|
||||
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
|
||||
register "wake" = "GPE0_DW2_14"
|
||||
register "detect" = "1"
|
||||
device i2c 15 on end
|
||||
end
|
||||
chip drivers/i2c/hid
|
||||
register "generic.hid" = ""SYNA0000""
|
||||
register "generic.cid" = ""ACPI0C50""
|
||||
register "generic.desc" = ""Synaptics Touchpad""
|
||||
register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
|
||||
register "generic.wake" = "GPE0_DW2_14"
|
||||
register "generic.detect" = "1"
|
||||
register "hid_desc_reg_offset" = "0x20"
|
||||
device i2c 2c on end
|
||||
end
|
||||
end
|
||||
device ref pcie_rp7 off end
|
||||
device ref cnvi_wifi on
|
||||
chip drivers/wifi/generic
|
||||
register "wake" = "GPE0_PME_B0"
|
||||
register "enable_cnvi_ddr_rfim" = "true"
|
||||
register "add_acpi_dma_property" = "true"
|
||||
device generic 0 on end
|
||||
end
|
||||
end
|
||||
device ref pch_espi on
|
||||
chip ec/google/chromeec
|
||||
use conn0 as mux_conn[0]
|
||||
device pnp 0c09.0 on end
|
||||
end
|
||||
end
|
||||
device ref pmc hidden
|
||||
chip drivers/intel/pmc_mux
|
||||
device generic 0 on
|
||||
chip drivers/intel/pmc_mux/conn
|
||||
use usb2_port1 as usb2_port
|
||||
use tcss_usb3_port1 as usb3_port
|
||||
device generic 0 alias conn0 on end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
device ref tcss_xhci on
|
||||
chip drivers/usb/acpi
|
||||
device ref tcss_root_hub on
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-C Port C0 (MLB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
|
||||
device ref tcss_usb3_port1 on end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
device ref xhci on
|
||||
chip drivers/usb/acpi
|
||||
device ref xhci_root_hub on
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-C Port C0 (MLB)""
|
||||
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
|
||||
device ref usb2_port1 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-A Port A0 (DB)""
|
||||
register "type" = "UPC_TYPE_A"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
|
||||
device ref usb2_port3 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Type-A Port A1 (DB)""
|
||||
register "type" = "UPC_TYPE_A"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
|
||||
device ref usb2_port4 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Camera""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
device ref usb2_port6 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Bluetooth""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
register "reset_gpio" =
|
||||
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
|
||||
device ref usb2_port8 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB2 Bluetooth""
|
||||
register "type" = "UPC_TYPE_INTERNAL"
|
||||
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
|
||||
device ref usb2_port10 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-A Port A0 (MLB)""
|
||||
register "type" = "UPC_TYPE_USB3_A"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
|
||||
device ref usb3_port1 on end
|
||||
end
|
||||
chip drivers/usb/acpi
|
||||
register "desc" = ""USB3 Type-A Port A1 (DB)""
|
||||
register "type" = "UPC_TYPE_USB3_A"
|
||||
register "use_custom_pld" = "true"
|
||||
register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
|
||||
device ref usb3_port2 on end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
end
|
||||
|
||||
end
|
||||
|
|
|
|||
Loading…
Reference in New Issue