In case the TPM is doing a long crypto operation the initial probe
could be very delayed. Rather than end up in recovery make the delay
long enough to accommodate the (current) long crypto times. This would
add a maximum of 30 seconds to boot time.
Mirroring changes done on i2c side in CL:756918
BUG=b:65867313, b:68729265
BRANCH=None
TEST=Make sure fizz boots up
Change-Id: Ie944bfb6fe33d6e9ee794439165716ab624be491
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Set the EC SCI reporting mask to include the power plug reporting.
BUG=b:65637324
TEST=Check power_supply_info on AC/DC.
Change-Id: I58814fc495081ffe8e47162da0fa4fbeba49d67b
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Code within carrizo_fch should be SOC specific instead of board specific.
BUG=b:64034810
Change-Id: I5de2020411794bfcd3730789f62af9c9834a018b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22455
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable the ACPI DBG2 table generation for Intel boards. This is
a Microsoft defined ACPI extension that allows an OS to know what
the debug port is on a system when it is not enabled by the
firmware, so it does not show up in the coreboot tables and
cannot be easily found by a payload.
broadwell: Use byte access device, set up only when enabled since
it relies on the port being put in byte access mode and using
this serial port for debug was not standard in this generation.
skylake: Enable for the configured debug port. Skylake uses
intelblocks for UART but not ACPI.
common: Enable for the configured debug port. This affects
apollolake and cannonlake.
Tested by compiling for apollolake/broadwell, tested by reading
the DBG2 ACPI table on kabylake board and using IASL to dump:
[000h 0000 4] Signature : "DBG2"
[004h 0004 4] Table Length : 00000061
[008h 0008 1] Revision : 00
[009h 0009 1] Checksum : 3B
[00Ah 0010 6] Oem ID : "CORE "
[010h 0016 8] Oem Table ID : "COREBOOT"
[018h 0024 4] Oem Revision : 00000000
[01Ch 0028 4] Asl Compiler ID : "CORE"
[020h 0032 4] Asl Compiler Revision : 00000000
[024h 0036 4] Info Offset : 0000002C
[028h 0040 4] Info Count : 00000001
[02Ch 0044 1] Revision : 00
[02Dh 0045 2] Length : 0035
[02Fh 0047 1] Register Count : 01
[030h 0048 2] Namepath Length : 000F
[032h 0050 2] Namepath Offset : 0026
[034h 0052 2] OEM Data Length : 0000
[036h 0054 2] OEM Data Offset : 0000
[038h 0056 2] Port Type : 8000
[03Ah 0058 2] Port Subtype : 0000
[03Ch 0060 2] Reserved : 0000
[03Eh 0062 2] Base Address Offset : 0016
[040h 0064 2] Address Size Offset : 0022
[042h 0066 12] Base Address Register : [Generic Address Structure]
[042h 0066 1] Space ID : 00 [SystemMemory]
[043h 0067 1] Bit Width : 00
[044h 0068 1] Bit Offset : 00
[045h 0069 1] Encoded Access Width : 03 [DWord Access:32]
[046h 0070 8] Address : 00000000FE034000
[04Eh 0078 4] Address Size : 00001000
[052h 0082 15] Namepath : "\_SB.PCI0.UAR2"
Change-Id: If34a3d2252896e0b0f762136760ab981afc12a2f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
During S3 cycling, system entered S3 only once and falied to
enter S3 the second time. The system gets stuck at this point
and we have to do a cold reboot to restore the system.
Since XHCI IP is able to power gate during kernel freeze/suspend,
this patch removes unnecessary device gating from ASL. This helps
in continuous cycling of S3.
BUG=b:69115421
TEST=run powerd_dbus_suspend multiple times and check if
the system enters and resumes from S3.
Change-Id: Id459631ea2d32feea4b8f658fd34fa25945f909e
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/22389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This further allows compilation units to be re-used without
having to add macro guards because of declarations not being
around in the __SIMPLE_DEVICE__ case. These declarations are for
functions that operate on struct device. struct device is a known
type so just expose the functions using the correct type. Also,
DEVTREE_CONST is empty while in ramstage so there's no reason
to separate the declarations. Lastly, fix up device_util.c to
use the proper types. It's only compiled in ramstage and it only
operates on struct device.
Change-Id: I306e0ad220cdab738cb727dda4a93bdec77c5521
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This feature was enabled at the kernel level, but that is triggering an
issue where FSP expects it to be disabled so it forces a cold reboot on
every warm reboot. Since we want this enabled anyway just set it this
way in the BIOS so it matches what the kernel expects.
BUG=b:68666100
TEST=pass firmware_FWtries on Eve with R63 OS image
Change-Id: I294e34d25406365d591da06ce4c931b710cfbbaa
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: I964d3d30392d130e808f37a661f2c89ec926cf58
Original-Signed-off-by: Duncan Laurie <dlaurie@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/749733
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tune PCH I2C4 hold times to ensure the frequency is always <400KHz.
BUG=b:67029862
TEST=boot on eve and measure I2C4 at Tp262 to be 385KHz
Change-Id: Ie93c5c40bc74069b285f6c3ee311f1bd7cefcaf1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: Iceabc806a17b9e6a144a4f6288c6cca790d03950
Original-Signed-off-by: Duncan Laurie <dlaurie@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/739841
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
AER and LTR must be enabled individually on ports that need it,
in this case it should be enabled for WiFi and NVMe.
BUG=b:65457528
TEST=Wifi team verified that the performance is better with these changes.
Change-Id: I0d688fe07a1f3117c1ca617c2ce78e0d024a3510
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: Ib059517fa782ccc18ba5ef1f76058a1898b7bf7a
Original-Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/671211
Original-Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Original-Commit-Queue: Duncan Laurie <dlaurie@google.com>
Original-Tested-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/22447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use the rt5663 driver and provide values for the offsets which are
needed for providing manual values to compensate the DC offset for
L and R channels between headphone and headset.
BUG=b:62712227
TEST=build and boot on eve and ensure rt5663 is functional.
Change-Id: I88113616e4b7c79cff840168b7c54ae754dfa75f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: Ica4090636c1ff29f0298114e62c9cc6fe167a425
Original-Signed-off-by: Duncan Laurie <dlaurie@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/611606
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-by: Hsinyu Chao <hychao@chromium.org>
Reviewed-on: https://review.coreboot.org/22446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change the touchscreen power control back to coreboot instead of
under the ACPI _ON/_OFF methods, and switch the TOUCHSCREEN_STOP_L
pin back to an output.
This reverts previous changes to touchscreen GPIOs that were made
to get back to a known good/working state. Having ACPI control these
pins was resulting in a small percentage of touchscreen not being
discovered at boot. This platform is not intending to use S0ix so
the ACPI control is not needed.
BUG=b:63718744
TEST=manual testing on Eve devices.
Change-Id: I3fd64a435a053da1558ef736fe7baceee3c8f3a0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Change-Id: Ia1e2ae7ca2a8b668c60fbda2aa50373e580646b2
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/572692
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Original-Commit-Queue: Duncan Laurie <dlaurie@google.com>
Original-Tested-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/22445
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
All AGESA headers should be included only through agesawrapper.h
BUG=b:66818758
TEST=Build gardenia
Change-Id: I3c9ae7a435fadabf577f1f65ad4a6aa6234e9a29
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
All AGESA headers should be included only through agesawrapper.h
BUG=b:66818758
TEST=Build gardenia; Build & boot kahlee
Change-Id: Iadc516e11148048ed9bf43c7a46827793245027a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
All AGESA headers should be included only through agesawrapper.h
BUG=b:66818758
TEST=Build gardenia; Build & boot kahlee
Change-Id: I94140235f46a627dda99540af8619aeca3f4f157
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
All Stoney AGESA headers should be included only through agesawrapper.h
BUG=b:66818758
TEST=Build and boot tested
Change-Id: I642f5caf8a37ae4042c32fec3a92e0995193cb7a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Create header files for the stoneyridge PI that pulls in AGESA pi
headers and encloses them in #pragma pack push/pop to keep the
'#pragma pack(1)' in Porting.h from leaking.
- Add that header to agesawrapper.h, replacing AGESA.h and Porting.h
Following patches will update the coreboot code to use only
agesawrapper.h to pull in the AGESA headers.
BUG=b:66818758
TEST=Build tested
Change-Id: Ib7d76811c1270ec7ef71266d84f3960919b792d4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add register HPPI and GSTS.
Add method WLSW that is used by thinkpad_acpi kernel module.
Seperate method by an empty newline.
Change-Id: I5a125047fad0e08cd9256bc53c3f5a7db7e56e7d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Fix how the SPI driver is accessed in spi_SaveS3info. This code has
been unused to date.
Change-Id: Ie2b97c13079fd049f6e02f3ff8fa630ed880343f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add the ability to locate the SMRAM-based SMU firmware early and
call the PSP library to load it prior to DRAM initialization. This
is currently placed in bootblock to ensure the blob is loaded
before any reset occurs.
Add similar functionality in ramstage for SMU FW2 to the hook already
in place for running AmdInitEnv. Rename the hook to make more sense.
This patch was tested using a pre-released PSP bootloader on a
google/kahlee system.
Leave the option unused until the bootloader is ready.
BUG=b:66339938
Change-Id: Iedf768e54a7c3b3e7cf07e266a6906923c0fad42
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Hudson code, the basis for soc//stoneyridge southbridge, has typically
contained direct calls to vendorcode/amd//ImcLib.c. In an effort to
keep #include files clean in other stoneyridge files, put the new calls
into imc.c.
Change-Id: I830d5431635ac4acaf3c3c974cb452847dc147cd
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Use more descriptive #define values for the ACPI features and
register decoding.
Change-Id: Iaaf9f9bd5761001bc4bfe6b64a6c72b1f04844bd
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22427
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Instead of getting the address of the GPIO function with an extern,
add a getter function and make the GPIO arrays static.
TEST=Build Grunt; Build & boot Kahlee
BUG=b:69164070
Change-Id: I3defcb66696459b915d7d4f43234d5c08ab7d417
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
mainboard.h only had a single function definition. Move it into
baseboard/variants.h and get rid of the file.
TEST=Build grunt/kahlee
BUG=b:69164070
Change-Id: I6b7d50d5c949733d77c42b4daf56ed1f97ed6954
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update common files and add files for grunt to the variant directory.
BUG=b:68293392
TEST=Build only
Change-Id: I7b80e470058872d6613e66e64c8dd1494942e9b9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Print error message when using common i2c without default clock defined.
TEST=Do not define default clock in Kconfig, compile will stop for
assertion.
Change-Id: I803f97698b3928e6b64df0010e71a6ded1400f87
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Default LPSS clock need to be defined for SOC.
TEST=Turn on COMMON_I2C_DEBUG, add I2C clock entry and check I2C
programing properly during coreboot.
Change-Id: I2c6b9bb23950b09f6f05e3ef762ccb1a260efc5f
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Stoney Ridge ASL uses global NVS for sharing data between ACPI and SMM.
Change-Id: I8f497870844da1f56ff5c3b126d5613be36a9bfb
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Explicitly add #include files to romstage.c to ensure sizes of the
devicetree structures are correct. The AMD support headers have an
open #pragma pack(1) which causes structure sizes to change based on
include ordering in different compilation units. More concretely, this
fixes a bug where dev->chip_info is incorrectly detected as 0.
Also shorten a printk string to bring the source line within 80 columns.
Change-Id: I1ed51cdbb8df387a453de6cb944b90538dac4431
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Several SPD hex files for chell were missing from upstream coreboot
(as compared to the Chromium tree/branch), which resulted in the
incorrect type and amount of RAM being reported on chell boards
with > 4GB RAM. Add these missing files and their Makefile entries.
TEST: boot google/chell m7/16GB config and observe correct RAM
type and amount reported via dmidecode and cbmem console log.
Change-Id: I37d708c96e754b438e40fc413420aa64bf234c29
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22402
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ModuleIdentifier must be 8 bytes. Every other location else that uses
this value explicityly defines it as 8 bytes. If it's initialized here
to less than 8 bytes, it gets passed to those other locations with
garbage at the end and fails to load the AGESA binary.
TEST=Build & boot Kahlee
BUG=B:69165234
Change-Id: I11fc90748f49782e2b16ee5326aee17cfe92d0bc
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Martin Roth