CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Add to init_fidvid_stage2 some step for my CPU (rev C3)
mentioned in BKDG 2.4.2.6 (5) that was missing
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6403 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Looking at BKDG the process for updating
Pstate Nb vid after warn reset seemed
more similar to the codethat was there fo
pvi than the one for svi, so I called the
pvi function passing a pvi/svi flag. I don't
find documentation on why should UpdateSinglePlaneNbVid()
be called in PVI, but since I can't test it,
I leave it as it was.
This patch showed some progress beyond fidvid in my
boar,d but only sometimes, most times it just didn't
work.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6402 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Factor out some common expressions.
Add an error message when coreboots hangs waiting for a pstate
that never comes (it happened to me), and throw some
paranoia at it for good mesure.
If I understood BKDG fam10 CPUs never need a software initiated vid transition,
because the hardware knows what to do when you just request
a Pstate change if the cpu is properly configured. In fact
unifying a little what PVI and SVI do was better for my board (SVI).
So I drop transitionVid, which I didn't understand either (why
did it have a case for PVI if it is never called for PVI ?
Why did the PVI case distinguigh cpu or nb when PVI is
theoretically single voltage plane ? ).
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6401 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
actual SIO. This fixes the serial device being disabled during PNP
init.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6400 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Contemplate the possibility of nbCofVidUpdate not being
defined, trying to get closer to BKDG
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6399 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Configuration of F3x[84:80] was hardcoded for rev B.
I change that for some code that checks for revision
and configures according to BKDG. Unfinished but
hopefully better than it was.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6398 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
BKDG says nbSynPtrAdj may also be 6 sometimes.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6397 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
I didn't understand quite why it did that iwth F3xA0 (Power
Control Misc Register) so I moved Pll Lock time to rules in defaults.h
and reimplemented F3xA0 programming. A later patch will remove
a part I don't know what's mean to do.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6396 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Bring F3xD4 (Clock/Power Control Register 0) more in line
with BKDG i more cases. It requires looking at the CPU package type
so I add a function for that (in the wrong place?) and some
new constants
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6395 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . Factor out the decision whether
to update northbridge frequency and voltage because there
was the same code in 3 places and so we can later modify it
in one place.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . Factor out the decision whether
to update northbridge frequency and voltage because there
was the same code in 3 places and so we can later modify it
in one place.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6393 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid. Factor out a little common code.
Also, our earlier config_clk_power_ctrl_reg0
was still too long and it'd get longer with forthcoming patches.
We now take apart F3xD4[PowerStepUp,PowerStepDown]
to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6392 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart F3x[84:80],
ACPI Power State Control Registers, to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6391 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart F3xDC[NbsynPtrAdj],
Northbridge/core synchronization FIFO pointer adjust, to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6390 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart F3xA0,
Power Control Misc Register to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart F3xD4,
Clock Power/Timing Control 0 to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6388 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode). No change of behaviour intended.
Refactor FAM10 fidvid . prep_fid_change was already long and it'd
get longer with forthcoming patches. We now take apart VSRamp in step b
of 2.4.1.7 BKDG to its own function.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6384 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
A video option rom must be added for UMA graphics support. It can
be extracted from the supplied UEFI BIOS.
ASRock E350M1 support is based on the AMD persimmon project. The
major differences are SIO model and DIMM SDP addressing. With this
coreboot and seabios, the board can boot DOS from a SATA drive and
can boot WinPE from a USB flash drive. I was unable to get
Windows setup to run.
The board has a socketed SPI flash BIOS chip and a serial port
header. The SIO is Nuvoton NCT5572D. Using coreboot's existing
Winbond w83627hf is a good enough match to get the serial port
and keyboard working.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6382 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also it enables the FID/VID changes in SB. Jakllsch had some troubles with that too but on am2 CPU. Those bits are only documented in SB600. They arent in RRG RPR and BDG.
Signed-off-by: Rudolf Marek <r.marek@asssembler.cz>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6381 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This affects the CMOS options iommu, ECC_memory, max_mem_clock,
hw_scrubber, interleave_chip_selects.
If they're absent in cmos.layout, a Kconfig value is used if it exists,
or a hardcoded default otherwise.
[Patrick: I changed the ramstage CMOS handling a bit, and dropped the
reliance of hw_scrubber on ECC RAM, as it has nothing to do with it -
it's the cache that's being scrubbed here.]
Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6380 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot used to set the chipset to IDE mode unconditionally.
Now, the user has a couple of ways to choose the configuration:
- If a CMOS variable sata_mode exist, it is used to decide if IDE or
AHCI is to be used as interface.
- If not, a Kconfig option is used.
- If unchanged, the Kconfig option is set to IDE.
So unless the cmos.layout is extended or Kconfig is modified, this won't
change behaviour.
[Patrick: Compared to Josef's version, I changed the Kconfig option to
be boolean, instead of a magic string. Also, the "IDE" default is
handled in Kconfig, instead of an additional line of code.]
Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6379 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The southbridge already provides hard_reset.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6378 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Otherwise they exist in several object files, confusing the linker
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6377 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
KERNELVERSION issue found by Stefan is fixed.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6375 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The current code works only with dual channel if Channel 0 uses SPD address
0x50/0x51, while the second channel has to use 0x52/0x53.
For hardware that uses other addresses (like the ThinkPad X60) this means we
get only one module running instead of both.
This patch adds a second parameter to sdram_initialize, which is an array with
2 * DIMM_SOCKETS members. It should contain the SPD addresses for every single
DIMM socket. If NULL is given as the second parameter, the code uses the old
addressing scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6374 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Instead of enable the device the device gets disabled. However after some time the serial line gets back, most likely some "enable resources" might fix it.
I'm attaching patch which somewhat fixes the problem and changes the function to look same in all superio code. Some boards even did not convert the dev->enabled to 0,1 values.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6373 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6372 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6371 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch also disables FDC37M81x since it has a conflicting device ID
and is not supported very well anyway.
Signed-off-by: David Hendricks <dhendrix@google.com>
Acked-by: Stefan Reinauer <reinauer@google.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6370 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It currently supports:
- Sleepbutton
- AC state
- Battery state
- Interrupt routing
- Display Brightness control
- Hotkeys
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6368 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The K8T800 is almost identical to the K8T800Pro, also added to this patch.
The K8T800_OLD is also defined, which is an older version of the K8T800,
but which has no driver and early HT code yet. Also extended the K8M890 VGA
driver to work for the K8M800 (not tested). According to the datasheet, the
K8T890 and K8T800 are similar enough to be able to use the same
initialization code. At least for the K8T800, this is sufficient to have
a working HT link with the CPU, and to initialise the V-Link to the
southbridge.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6367 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It is incorrect, and will be replaced with proper ACPI for X60.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fixes abuild issues.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6363 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Adds support for Lenovo X60 series ThinkPads. So far, only X60s
(Model 1703) has been tested.
It's a basic patch without SMI and ACPI, as this makes it easier to
review. SMI and ACPI patches will follow.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6359 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add FILE*
- Add stdout, stdin, stderr stubs
- Add fprintf that redirects to printf for stdout and stderr and fails otherwise
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6358 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6357 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Setting bit#21 in k8_f0#68 is part of the errata#169
which is handled in amdk8/coherent.c
Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6354 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Xavi Drudis Ferran