The hardware IRQ option was not passed to SeaBIOS Makefile and resulted
in HARDWARE_IRQ being permanently disabled regardless of Kconfig
selection in coreboot. On platforms that need the hardware IRQ it caused
hangs at boot menu or iPXE prompts.
TEST=enter SeaBIOS boot menu on Libretrend LT1000
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iafcfd743177bbcd1ee23e227c74dd8268c4c23c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
For a very long time, SeaBIOS sometimes failed to build when using
multiple threads. This known problem has been haunting everyone for a
very long time. Until now.
Unlike most other payloads, building SeaBIOS results in two files: the
SeaBIOS payload itself and SeaVGABIOS. Each file has its own target, and
there's a third target called "seabios", which has the same recipe as
the SeaBIOS file, which calls `payloads/external/SeaBIOS/Makefile` with
a bunch of arguments. In addition, SeaVGABIOS depends on "seabios".
When executing serially, if the file of either SeaBIOS or SeaVGABIOS is
needed, the SeaBIOS Makefile will be run. This will generate both files,
so it is not necessary to run the Makefile more than once.
However, when using multiple threads, it can happen that one thread
wants to make the SeaBIOS file, while another one wants to make the
SeaVGABIOS file, which depends on "seabios". This implies that both
threads will execute the SeaBIOS Makefile at about the same time, only
to collide when performing git operations. Since git uses a lock file
when updating the index, one of the threads will fail to acquire the
lock with an error, which will ultimately cause the build to fail.
Whenever this happened, manually aborting with Ctrl-C made the build
process fail again because of the same error. The only way to get past
this problem, other than using one thread, was to let the unfinished
jobs complete. The thread that acquired the lock on the SeaBIOS git
repository would finish building SeaBIOS, so that target would not need
to be remade. When restarting the build, only the target that failed is
rebuilt, so it does not collide with any other thread.
To address this issue, make the SeaVGABIOS file target depend directly
on the SeaBIOS file instead, and remove the duplicate "seabios" target.
Change-Id: I251190d3bb27052ff474f3cd1a45022dab6fac31
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
CONFIG_MAINBOARD_DEPTHCHARGE is set to "" for
boards not configuring it.
Signed-off-by: Selma BENSAID <selma.bensaid@intel.com>
Change-Id: If61a1371ad8baf165b09ce045fc1a6c205c2c0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
CONFIG_MAINBOARD_DEPTHCHARGE is used to override the Board
config for depthcharge which inherit from CONFIG_MAINBOARD_PART_NUMBER.
This is mainly to avoid depthcharge config duplication.
Signed-off-by: Selma BENSAID <selma.bensaid@intel.com>
Change-Id: I6cbc93ca38ad6deeca2c2fb7770024a24233b6f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
corebootpayload package in upstream TianoCore was replaced with
UEFIPayload, add external payload build option for UEFIPayload.
BUG=N/A
TEST=Select TianoCore payload as UEFIPayload, build and able to boot up on
QEMU q35 after PCIE_BASE set.
Change-Id: I0b7785fde9f4113b2cd91323ac0358b229c5a6e6
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34459
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pass `XGCCPATH` instead of individual programs as that is what the
Makefile expects.
Change-Id: I3267ec5259e9d37b2f3b0b8c126d173fc8b5a3ca
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Add two new options:
* Disable the prompt "Press Ctrl+B for the iPXE command line..."
Add a boolean that disables the initial 2 second timeout.
* Include a script that is executed instead of showing a shell.
Allows to add a script that will be included into the iPXE ROM.
Tested on Lenovo T500 and PC Engines apu2.
Change-Id: Ie1083d8571d9d1f1c7c71659fb6ff0de2eecad0e
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/20782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add Kconfig options to use custom bootsplash file,
dependent on using MrChromebox's stable branch, with
help info conveying required file format.
Adjust Makefile to copy the custom bootsplash and
overwrite the default Logo.bmp file, handling both
absolute and relative paths, and restore the original
logo file after building so as to keep the working
directory clean.
Test: build with and without custom bootsplash, ensure
correct bootsplash displayed
Change-Id: I164f46777169801cff56633fd920bc81b7c8129a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Clean and refactor the structure of the LinuxBoot payload integration,
to make it more modular and readable. The kernel and initramfs should
handled in separated makefiles.
tested with:
- qemu-i440fx (x86, x86_64)
- cavium CN8100 (arm64)
Change-Id: I41d0275a5f7efb920e881f43b0acda29f41ee221
Signed-off-by: Marcello Sylvester Bauer <info@marcellobauer.com>
Reviewed-on: https://review.coreboot.org/c/29581
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Merge the command-line and initramfs parser from 'a linux payload'
and 'LinuxBoot'.
GOAL: merge 'a Linux payload' and 'LinuxBoot'
Change-Id: I2d2aef5d07453b98e115af6ee06318c690def785
Signed-off-by: Marcello Sylvester Bauer <info@marcellobauer.com>
Reviewed-on: https://review.coreboot.org/29510
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Yabits (Yet another UEFI bootloader) is designed to be a slim and quick
alternative to Tianocore. It is still under heavy development.
https://web.archive.org/web/https://yabits.github.io/
Change-Id: I132970e952c605c73cfe33dc47f20170ae8aa899
Signed-off-by: Martin Roth <martin@coreboot.org>
Reviewed-on: https://review.coreboot.org/28590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Change TianoCore payload default to use HPET timer. Add an option to use
8254 timer for legacy platform support.
BUG=N/A.
TEST=Build and boot up into UEFI shell on Whiskey Lake rvp platform.
Change-Id: I857704b0ca128fc9da193ae26a33c7cf89ad7320
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Because the Kconfig configuration files for primary payloads are
already sourced via a wildcard pattern this change requires to
use another file name pattern.
Change-Id: I83b89f5e14618e8a487ebb044fcdd3c175662591
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Curley brace expansion is a bash-ism, so we can't use it for the
u-root command list.
This unfortunately also breaks the current Kconfig option since the
list needs to be separated by space instead of commas.
Change-Id: I429a52c1673e29b7180ee6f53deaa7a551a1a9b3
Signed-off-by: David Hendricks <dhendricks@fb.com>
Reviewed-on: https://review.coreboot.org/27967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add support for ARCH=ARM64 and introduce CROSS_COMPILE for all architectures.
* Always compress kernel Image using xz
* Create FIT uImage containing the kernel, initramfs and DTB
* Add ARM64 defconfig for all SoCs
Change-Id: I9a0cc248283432fb2384956ca55e687d4127398c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Since SeaBIOS 1.11.0 implements serial console and etc/sercon-port
runtime config file is present in CBFS, SeaBIOS additionally
redirects iPXE output to configured IO port. For boards which use
the same UART for SeaBIOS and iPXE console it causes doubled
output.
The option is enabled by default and passes UART configuration
to iPXE Makefile as before. When unselected, only SeaBIOS handles
printing output from iPXE.
Change-Id: Ia3c74cfbee4f816782161fcff286a14f46be78c5
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This reverts commit 717ba74836.
This breaks seabios and a few other payloads. This is not
ready for use.
Change-Id: I48ebe2e2628c11e935357b900d01953882cd20dd
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/26310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Currently, adding a payload to CBFS using the build system, the warning
below is shown.
W: Unknown type 'payload' ignored
Update payload type from "simple elf" to "simple_elf" and rename the
word "payload" to "simple_elf" in all Makefiles.
Fixes: 4f5bed52 (cbfs: Rename CBFS_TYPE_PAYLOAD to CBFS_TYPE_SELF)
Change-Id: Iccf6cc889b7ddd0c6ae04bda194fe5f9c00e495d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/26240
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both GRUB and SeaBIOS can chainload lzma compressed payloads.
Therefore it is beneficial to compress secondary payloads
like Memtest86+, coreinfo, nvramcui,... for both size reasons and
often also speed reasons since the limiting factor is generally the
IO of the boot device.
Tested with SeaBIOS and memtest86+ master on Thinkpad X220.
Change-Id: Iddfd6fcf4112d255cc7b2b49b99bf5ea4d6f8db4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The MMIO address can change for different platforms
like Apollolake.
Change-Id: I6ec72d3a14f00212323a04e20d5a477dbc26b770
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
The depthcharge .config only exists after depthcharge was built. Other
possible `PAYLOAD_CONFIG` files most probably miss a rule, too.
Change-Id: I8e6f79bb2bd07cbef1317f2623bbef9ca0e74880
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/22137
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This should make reproducible builds of coreboot with GRUB2 easier.
Change-Id: If855042945ab34f34c554e7490c811ec7b256980
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/22527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We were explicitly passing CC and TARGET_CC to configure but overwrote
that decision later by passing CC (with the value of TARGET_CC) directly
to a recursive make call. The latter overwrite was introduced because
`unexport` alone doesn't work on variables that were specified on a make
command line (they are added to MAKEOVERRIDES and passed to further re-
cursive make calls).
Instead of unexporting random variables, unexport those that were actu-
ally passed from payloads/external/Makefile.inc and clear MAKEOVERRIDES.
Do not pass OBJDUMP as that is nowhere to be found in the GRUB sources.
And, last but not least, add --disable-werror because building GRUB is
very susceptible to changes in the flex version.
Change-Id: Iaff2c72e89a5a540fe365eacb84811d5cff9d4d4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Update the existing tianocore payload (which didn't do any more than
adding an elf payload with a specific name) to fetch and build the
UEFI corebootPayloadPackage, using the coreboot toolchain for
compilation. Only checkout the commit when changing commit IDs or if
version is master, instead of every time it builds.
Currently working if patches are merged into the upstream edk2
repository (to be included in a follow-on patch).
Change-Id: I0bf4cedec2d6821ae2a04184ebb5cf88979ccee3
Signed-off-by: Martin Roth <martinroth@google.com>
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Signed-off-by: Evelyn Huang <evhuang@google.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/15057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Since version 9332965 "serialio: Support for mmap serial ports", SeaBIOS
supports memory mapped serial ports. This patch automatically configures
SeaBIOS when the Hudson UART is enabled.
Change-Id: I072f6a957df7e143d790783546b0725bcd597d9c
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-on: https://review.coreboot.org/18025
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change is based on the following commit:
3aa91dc payloads/seabios: Add "git revision" to the SeaBIOS version menu
Change-Id: I9987e3673e70b5cb20173d1ddff6060f42a5374a
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: https://review.coreboot.org/18352
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Change depthcharge to not require a board-specific config file for
libpayload. If the Kconfig option is selected, use the settings
in libpayload/configs/defconfig instead.
Change-Id: I4fd1a5915472f28e757c62f3f2415716f1fdfc71
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18271
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add the capability for specifying which version of depthcharge to
checkout and build. This is similar to the existing feature for
SeaBIOS.
The depthcharge makefile already contains some structure for checking
out master vs. stable however the calling Makefile.inc ingored this
feature. Add the command-line variable assignment for these, along
with a tree-ish for any revision.
Change-Id: I99a5b088cb0ebb29e5d96a84217b3bfa852de8ac
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18270
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Previously SeaBIOS's default was used (1). This patch defaults to
coreboot's console level instead which is approximately the same
verbosity as SeaBIOS and thus what a user would probably expect.
Change-Id: If79e5f40c9380bb527f870eeb7d0cb43faf00beb
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/18051
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Including $(top) in the DOTCONFIG definition allows getting rid of the
$(top) prefix in payloads, which in turns allows providing a full path
for DOTCONFIG via the command line.
Change-Id: I7546a12cf4a2a146e32fef81121f45f83ba67ac8
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/15826
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Set CONFIG_GRUB2_EXTRA_MODULES from the Kconfig when building GRUB2.
This causes the specified modules to actually enter the built payload.
Change-Id: I345026af705ba8af77c6c12aba8e1bd4135e519c
Signed-off-by: Benjamin Barenblat <bbaren@google.com>
Reviewed-on: https://review.coreboot.org/15203
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Including the SeaBIOS bootorder file seems to be a fairly common desire,
so let's make it easy.
Change-Id: Ib0874dee46215287b09c0b52648072ef3ff06ec5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15076
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Commit 785a31d67e
(Makefile.inc: Move payload code to payloads/) breaks the usage of
Linux kernel as payload. The reason for it is that cbfs-files-y is
evaluated before payloads/external/Makefile.inc is sourced and as a
consequence ADDITIONAL_PAYLOAD_CONFIG is empty when it is used for
payload options. That leads to missing command line and initrd for
the kernel which in turn leads to kernel panic when it boots.
To avoid it, move the code which adds payload to cbfs completely to
payloads/extranal/Makefile.inc. This way, ADDITIONAL_PAYLOAD_CONFIG is
set right before the payload itself is added to cbfs-files-y.
I have tested this patch with a Linux kernel as well as with SeaBIOS as
payload on mc_tcu3 and it works. If someone sees impact to other
payloads just let me know.
Change-Id: I7aad352f8b3fc1fdba1875b12648b07eba14e282
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14579
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Memtest86+ was pulling origin/master which will change over time. This
adds a commit-id as a stable version to allow it to be reproducible.
The other secondary payloads, coreinfo and nvramcui, do not need this
because they are part of the coreboot repo and not fetched from an
external source.
Change-Id: I20c516010f76cf03342bd8883d0ee7ac5f8bc7e4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14520
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We already have the ability to add a pxe rom to cbfs, but it needs to be
configured and built separately.
This moves the existing Kconfig options for PXE from device/Kconfig and
the top level Makefile.inc to payloads, and adds the option to download
and build iPXE as part of the coreboot build process.
This configures the serial output of iPXE to match coreboot's serial
port configuration by editing the .h files. iPXE doesn't give any
real build-time method of setting these configuration options.
Change-Id: I3d77b2c6845b7f5f644440f6910c3b4533a0d415
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14085
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
These makefiles are not included by anything, so they shouldn't be
named Makefile.inc. Also, having them all be named 'Makefile' makes
some other consolidation work I'm doing much easier.
Change-Id: I1234539ba6a0a6f47d2eb0c21de3da3607c6b8de
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14130
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For CHROMEOS builds, depthcharge can be built automatically.
This dependency exists because depthcharge without vboot and subsequent
signing of the image doesn't work very well, and both are keyed to that
flag as well.
Change-Id: Id0195bd3b4e454f382782106d6512469106daac5
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/10924
Tested-by: build bot (Jenkins)
Add an option to specify a git revision from which to build SeaBIOS.
Change-Id: Ifbf3b82e784f79395ab7cd07c5804f72928d7640
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/13937
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins)
Currently, if SeaBIOS is set as the payload, it gets rebuilt every
single time we do a build.
Change it to re-build just when there’s a config change.
Change-Id: Ib141f2cbf8796d449172432bb30fa4806cf90328
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13948
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This allows memtest86+ to be added to CBFS as a 'secondary'
payload on x86 systems, to be loaded by the main payload
if desired.
Selecting this option, which defaults to no, builds the memtest86+
payload and adds it to CBFS as `img/memtest` which can then be
loaded by for example SeaBIOS or GRUB.
Change-Id: Iecf876aaf588ba1df7abdf6668cb26f089bf5f42
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13858
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ben Gardner <gardner.ben@gmail.com>
Michał Żygowski