This patch converts mainboard_$VENDOR_$BOARD_ops to mainboard_ops and
mainboard_$VENDOR_$BOARD_config to mainboard_config.
Ron's part:
The config change that makes the naming change not break every build.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3954 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Add a function to change the 24/48Mhz clock input selector on the Winbond
W83697 superio to 48Mhz, used by the WinNET P680
Signed-off-by: Alex Mauer <hawke@hawkesnest.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3661 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
targets/*/*/Makefile
targets/*/*/normal/Makefile
targets/*/*/fallback/Makefile
to use a common copy of romcc, and to leave this compiler untouched by
'make clean' in targets/*/*/fallback/ and targets/*/*/normal/ .
'make clean' in targets/*/*/ will clean romcc.
Thanks to Mats for the initial idea and implementation of a tool to do
this. This patch has almost the same behaviour as the original tool
without having to run the tool each time.
Tested for abuild-friendliness.
The patch saves ~10-12 seconds for every target using romcc. For a full
abuild run, this is ~20% time saved.
For the first 38 abuild targets, total build time is down to 13m24s
instead of 16m22s on my machine.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Mats Erik Andersson <mats.andersson@gisladisker.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3564 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
You can see this by executing commands like this:
grep -r pci_assign_irqs coreboot/src/*
This basically AMD/LX based boards: pcengines/alix1c,
digitallogic/msm800sev, artecgroup/dbe61, amd/norwich, amd/db800.
Also for AMD/GX1 based boards need a patch
[http://www.pengutronix.de/software/ptxdist/temporary-src/references/geode-5530.patch]
for the right IRQ setup.
AMD/GX1 based boards is: advantech/pcm-5820, asi/mb_5blmp, axus/tc320,
bcom/winnet100, eaglelion/5bcm, iei/nova4899r, iei/juki-511p.
I have two ideas.
1. Delete duplicate code from AMD/LX based boards.
2. Add IRQ routing for AMD/GX1 boards in coreboot.
The pirq.patch for IRQ routing logically consist from of two parts:
First part of pirq.patch independent from type chipsets and assign IRQ for
ever PCI device. It part based on AMD/LX write_pirq_routing_table() function.
Second part of pirq.patch depends of type chipset and set PIRQx lines
in interrupt router. This part supports only CS5530/5536 interrupt routers.
IRQ routing functionality is included through PIRQ_ROUTE in Config.lb.
Tested on iei/juki-511p(cs5530a), iei/pcisa-lx(cs5536) and also on
TeleVideo TC7020, see
http://www.coreboot.org/pipermail/coreboot/2007-December/027973.html.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3196 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Due to the automatic nature of this update, I am self-acking. It worked in
abuild.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code is changed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add missing entry for the NIC:
device pci 0f.0 on end # Ethernet (onboard)
- Drop the following lines:
register "com1" = "{115200}"
register "com2" = "{38400}"
Those entries hardcode the BAUD rate (as far as I can tell, please
correct me if I'm wrong). We don't want that -- instead the config option
TTYS0_BAUD in Options.lb should be used(?) I verified that dropping those
lines will not break serial output (COM1, 115200, 8n1).
- Enable IDE (PCI device 00:12.2) and add the following register lines
to tell the CS5530 code to actually enable IDE channel 0:
register "ide0_enable" = "1"
register "ide1_enable" = "0" # Not available/needed on this board
Tested with a 2.5" hard drive and FILO, works fine.
- Enable USB (PCI device 00:13.0), not sure why it was commented.
- Enable COM2 as it's used by the smartcard reader.
- Add CONFIG_COMPRESSED_PAYLOAD_LZMA to Options.lb, in order to fix
abuild for this board.
- Add some more comments.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2896 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
See http://www.linuxbios.org/BCOM_WINNET100_Build_Tutorial for hardware
description and build tutorials.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2843 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
