sense, too). Have one u64 instead of three.
In order to use the old bios emulator, you have to do nothing. (Default, if
CONFIG_PCI_ROM_RUN is enabled)
In order to use yabel in your target, you need to add the following lines to
your config:
uses CONFIG_PCI_OPTION_ROM_RUN_YABEL
default CONFIG_PCI_OPTION_ROM_RUN_YABEL=1
In order to use vm86 in your target, you need to add the following lines to
your config:
uses CONFIG_PCI_OPTION_ROM_RUN_VM86
default CONFIG_PCI_OPTION_ROM_RUN_VM86=1
Note: vm86 only works on platforms with _RAMBASE in the lower megabyte.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rather independent, lift the implicit (broken) assumption that
CONSOLE_VGA would also run the ROMs, and transfer it to a new
config option VGA_ROM_RUN.
This change is minimally intrusive, because all board configs
that previously assumed CONSOLE_VGA would also run the ROMs
didn't compile, they had to also specify PCI_ROM_RUN.
Based on patches by Ron Minnich (fix the compile) and Luc Verhaegen
(separate ROM_RUN from VGA console).
Signed-off-by: Torsten Duwe <duwe@lst.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Luc Verhaegen <libv@skynet.be>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3034 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. x86_setup_mtrr take address bit.
2. generic ht, pcix, pcie beidge...
3. scan bus and reset_bus
4. ht read ctrl to decide if the ht chain
is ready
5. Intel e7520 and e7525 support
6. new ich5r support
7. intel sb 6300 support.
yhlu patch
1. split x86_setup_mtrrs to fixed and var
2. if (resource->flags & IORESOURCE_FIXED ) return; in device.c pick_largest_resource
3. in_conherent.c K8_SCAN_PCI_BUS
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1982 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- The sandpointx3+altimus has been consolidated into one directory for now.
- Added support for having different versions of the pci access functions
on a per bus basis if needed.
Hopefully I have not broken something inadvertently.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Reworked pnp superio device support. Now complete superio support is less than 100 lines.
- Added support for hard coding resource assignments in Config.lb
- Minor bug fixes to romcc
- Initial support for catching the x86 processor BIST error codes. I've only seen
this trigger once in production during a very suspcious reset but...
- added raminit_test to test the code paths in raminit.c for the Opteron
- Removed the IORESOURCE_SET bit and added IORESOURCE_ASSIGNED and IORESOURCE_STORED
so we can tell what we have really done.
- Added generic AGP/IOMMU setting code to x86
- Added an implementation of memmove and removed reserved identifiers from memcpy
- Added minimal support for booting on pre b3 stepping K8 cores
- Moved the checksum on amd8111 boards because our default location was on top of
extended RTC registers
- On the Hdama added support for enabling i2c hub so we can get at the temperature
sensors. Not that i2c bus was implemented well enough to make that useful.
- Redid the Opteron port so we should only need one reset and most of memory initialization
is done in cpu_fixup. This is much, much faster.
- Attempted to make the VGA IO region assigment work. The code seems to work now...
- Redid the error handling in amdk8/raminit.c to distinguish between a bad value
and a smbus error, and moved memory clearing out to cpufixup.
- Removed CONFIG_KEYBOARD as it was useless. See pc87360/superio.c for how to
setup a legacy keyboard properly.
- Reworked the register values for standard hardware, moving the defintions from
chip.h into the headers of the initialization routines. This is much saner
and is actually implemented.
- Made the hdama port an under clockers BIOS. I debuged so many interesting problems.
- On amd8111_lpc added setup of architectural/legacy hardware
- Enabled PCI error reporting as much as possible.
- Enhanded build_opt_tbl to generate a header of the cmos option locations so
that romcc compiled code can query the cmos options.
- In romcc gracefully handle function names that degenerate into function pointers
- Bumped the version to 1.1.6 as we are getting closer to 2.0
TODO finish optimizing the HT links of non dual boards
TODO make all Opteron board work again
TODO convert all superio devices to use the new helpers
TODO convert the via/epia to freebios2 conventions
TODO cpu fixup/setup by cpu type
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1390 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Major restructuring of hypertransport handling.
Major rewerite of superio/NSC/pc87360 as a proof of concept for handling superio resources dynamically
Updates to hard_reset handling when resetting because of the need to change hypertransport link
speeds and widths.
(a) No longer assume the boot is good just because we get to a hard reset point.
(b) Set a flag to indicate that the BIOS triggered the reset so we don't decrement the
boot counter.
Updates to arima/hdama mptable so it tracks the new bus numbers
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1097 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* subtractive resources
* merging with the static device tree
* more device types than just pci
- The piece to watch out for is the new enable_resources method that was needed in all of the drivers
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1096 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Stefan Reinauer