The GPIO and GPIO MUX mapping as well as some GPIO to GEVENT mappings
have changed compared to Cezanne. Sabrina also doesn't have a remote
GPIO bank. Revision 1.50 of PPR #57243 was used as a reference.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iabb85a3d24c881055e94400d08d01505df44a07a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Compared to Cezanne there are 3 more UARTs controllers. The PCI
interrupt index table in the new SoC's PPR #57243 Rev 1.50 doesn't
contain a PIRQ mapping for UART4. The reference code has a mapping for
this and it uses PIRQ mapping index 0x77 for UART4 and not for I2C5.
Since the I2C5 controller isn't owned by the x86 side and I didn't see
any mapping of the I2C5 controller into the x86 MMIO space, this seems
very plausible. Also add the corresponding fields to the ACPI code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I44780f5bc20966e6cc9867fca609d67f2893163d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Some SKUs of google/taniks have a Bayhub LV2 card reader chip,
therefore enable the corresponding driver for the mainboard.
BUG=b:215487382
TEST=Build FW and checking SD card reader register is correct.
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I34adb122bd2edc343e894a53bc12e105f4225984
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
- Handle older CrOS firmware which lacks a COREBOOT FMAP region
- Add support for all blobs used in CrOS firmware 2013 to current
- Put extracted blobs in their own directory
Change-Id: Idaa39eca3be68a9327cead9b21c35a6c7a3a8166
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Without acpi name, acpi_device_path will return NULL.
<NULL>: Intel USB4 Retimer at GENERIC: 0.0
Replace with usb4_retimer_scope for the identify.
BUG=b:215742472
TEST=show below meaasge in coreboot log
\_SB.PCI0.TMD0.HR : Intel USB4 Retimer at GENERIC: 0.0
\_SB.PCI0.TMD1.HR : Intel USB4 Retimer at GENERIC: 0.0
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idfa8b204894409b11936e5f221c218daa206cc02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Intel Lynx Point ASL code is fixed. So don't ignore
"Multiple types (Device object requires either a _HID or _ADR, but not both)"
warning.
Change-Id: Ie9398879a76ad3d36454772a1c23da083af14b59
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
A simple GUI to change settings in coreboot's CBFS, via the nvramtool utility.
Test on the StarBook Mk IV running coreboot 4.15 with:
* Ubuntu 20.04
* Ubuntu 21.10
* MX Linux 21
* elementary OS 6
* Manjaro 21
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I491922bf55ed87c2339897099634a38f8d055876
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
When using the default initial core display clock frequency, Metaknight
has a rare stability issue where the startup of Chrome OS in secure mode
may hang. Slowing the initial core display clock frequency down to
172.8 MHz as per Intel recommendation avoids this problem.
The CdClock=0xff is set in dedede baseboard,and we overwrite it as 0x0
(172.8 MHz) for metaknight.
BUG=None
BRANCH=dedede
TEST=Build firmware and verify on fail DUTs.
Check the DUTs can boot up in secure mode well.
Change-Id: I987277fec2656fe6f10827bc6685d3d04093235e
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Set tcc_offset value to 10 in devicetree for Thermal Control Circuit
(TCC) activation feature. This value is suggested by Thermal team.
BUG=b:214890058
BRANCH=None
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I86acb172ed427d45973b9360e0413978cbd46645
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch drops the CSE common code block from getting compiled
in bootblock without any SoC code using heci communication so
early in the boot flow.
BUG=none
TEST=Able to build brya, purism/librem_skl without any compilation issue.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib4d221c6f19b60aeaf64696e64d0c4209dbf14e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Add new ram_id:1100 for memory part K4AAG165WB-BCWE.
BUG=b:212507858
TEST=Generate new spd file and build coreboot.
Then boot from the DUT with new memory K4AAG165WB-BCWE
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I4e409a5a5a3b3d1b0013d2c020eeb4c0aeec51ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Fix the out-of-bounds read issue found by Coverity.
TEST=none
Signed-off-by: Jason Nien <finaljason@gmail.com>
Change-Id: I01e134cb6b025bf7cb5030cd9378297d7f6df509
Reported-by: Coverity (CID:1376956)
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58803
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit b67c5ed [3rdparty/fsp: Update submodule pointer to newest master]
updated the FSP binaries/headers for Comet Lake, which included a change
moving PcieRpHotPlug from FSP-S to FSP-M. Unfortunately the existing
UDP in FSP-S was left in and deprecated, which allowed the change to go
unnoticed until it was discovered that hotplug wasn't working.
Since other related platforms (WHL, CFL) share the SoC code but use
different FSP packages, add the setting of the PcieRpHotPlug UPD to
romstage/FSP-M and guard it with '#if CONFIG(SOC_INTEL_COMETLAKE)'.
Test: build/boot Purism Librem 14, verify WiFi killswitch operates
as expected / WiFi is re-enabled when turning switch to on position.
Change-Id: I4e1c2ea909933ab21921e63ddeb31cefe1ceef13
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Level should match that used in print_num_status_bits().
Change-Id: I1beb65e4c141e195dd59eaa2bf55fff6e7dc910d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jeff Daly <jeffd@silicom-usa.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
This reverts commit 2bf2e6d1cc.
According to the latest schematics, Brask supports D3-Hot for RTL8125
and does not need to operate the ISOLATE pin.
BUG=b:193750191
BRANCH=None
TEST=emerge-brask coreboot chromeos-bootimage
Test with command suspend_stress_test
Change-Id: Ica6bfb810887861f6b17ff527373824547e2406c
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add the file templates for creating a new variant of Brask.
BUG=b:215091592
TEST=new_variant.py and build coreboot pass for the new variant.
Change-Id: I67e4ed450d6033fed7419bd7c76c127ecd942fe8
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Set register "reset_delay_ms" to 20 to reduce power resume time.
BUG=b:204009580
TEST=tested on kano
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ib0695edd7c342c65df9138b1590281c5f442769b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add PCH ACPI Device ID for Alder Lake N SOC GPIO Controller.
Document: Alder Lake N Platform EDS Volume 1 (Doc# 645548)
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I6eb15751dd303b4b445cb64f25a040302e50c09d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Set the SOC_INTEL_COMMON_BLOCK_GPIO_LOCK_USING_SBI config on Alder Lake
to instruct Pad Configuration Lock to use non-posted sideband writes as
posted write is not supported on Alder Lake while locking GPIO pads.
BUG=b:211573253, b:211950520
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Id8d394b97de9c328b3f75df3649d7efc782f006b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This patch extends `struct pad_config` to add new variable for gpio
lock action.
Additionally, it creates new GPIO PAD configuration macros that perform
GPIO pad configuration and pad lock configuration as well.
List of new macros are:
1. PAD_CFG_NF_LOCK
2. PAD_CFG_GPO_LOCK
3. PAD_CFG_GPI_LOCK
4. PAD_CFG_GPI_TRIG_OWN_LOCK
5. PAD_CFG_GPI_GPIO_DRIVER_LOCK
6. PAD_CFG_GPI_INT_LOCK
7. PAD_CFG_GPI_APIC_LOCK
8. PAD_CFG_GPI_IRQ_WAKE_LOCK
Mainboard users can use the above macros to lock the PAD after
configuration.
So far on IA chipset, the default GPIO pad lock configuration reset
type is POWERGOOD hence, it's recommended as per GPIO BWG (doc: 630603)
to configure the GPP PAD reset type the same as lock configuration
reset type to avoid GPP reset value misconfiguration issue.
BUG=b:211573253, b:211950520
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibf8b0a845005ad545266d995449d0aa711f45a61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This patch performs GPIO PAD lock configuration in non-smm mode.
Typically, coreboot enables SMI at latest boot phase post FSP-S,
hence, FSP-S might get chance to perform GPP lock configuration.
With this code changes, coreboot is able to perform GPIO PAD
lock configuration early in the boot flow, prior to calling FSP-S.
Also, this patch ensures to have two possible options as per GPIO
BWG to lock the GPIO PAD configuration.
1. Using SBI message with opcode 0x13
2. Using Private Configuration Register (PCR)
BUG=b:211573253, b:211950520
TEST=Able to build and boot brya variant with this code change.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I71b4e2f24303b6acb56debd581bd6bc818b6f926
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60801
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For one specific type of APU, it doesn't have HDMI. When we detect
this APU, we need to explicitly disable HDMI in DDI settings,
otherwise the system would freeze.
get_cpu_count() == 4 && get_threads_per_core() == 2: This case is for
2 Core and 4 Thread CPU (2C/4T for short).
get_cpu_count() == 2: This is for 2C/2T. This is for a possible future case.
BUG=b:208677293
Change-Id: I8d0fa96818a768b7960d92821b927dbc622675ae
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
This code is common to at least all Zen-based APUs (Picasso, Cezanne,
Sabrina) and is also useful outside of the SoC-specific dynamic ACPI
table generation code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie96d4429fb6ed9223efed9b3c754e04052d7ca7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-by: Eric Peers <epeers@google.com>
There is no wakeup source when we test function of suspend and resume.
The root cause is that the monitor enable bit of PWRAP is not configured
correctly.
BUG=b:213255218, b:214978483
TEST=receive wakeup source from MT6366 successfully
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I324d18fa5d3cd745c35fcf0f207e1b444b5e898b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61330
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The VERSTAGE region is only needed when running verstage in the x86.
This change reduces the early ram size by 512 KiB when using PSP
verstage.
BUG=none
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I45ce421397807dbb1eb48aedd05209b91e89aa4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reference test document, update tuning registers from pass experiment
setting of phy_settings.
The document about eDP tuning can be gotten from the issue tracker of
this ticket, at the issue tracker b/203061533#comment6.
BUG=b:203061533
Change-Id: I7aa8c594d9f5caa6b2523dac079aef89e623c56f
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The FSP gets these values from the UPD and sets the internal values.
The document about eDP tuning is attached in issue tracker of this
ticket, at the issue tracker b/203061533#comment6.
BUG=b:203061533
Cq-Depend: chrome-internal:4303901
Change-Id: I9b85faac4f2fa1fb2c14bb85b615346d4379baac
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This reverts commit bd9b044a96 ("mb/system76: rtd3: Remove SrcClk pin
on CPU RP").
Previously, RTD3 expected a PCH index for the root port and did not work
with the CPU PCIe RP present on TGL, so SrcClk pin was disabled.
Set them now that RTD3 supports mapping the index for the CPU RP.
Change-Id: Ia7519b9f5a2be52cd5575615c28d20371a26996b
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Taniks will use two PCIE port signals with one slot, one CLK and one
CLKREQ at next build. In order to accommodate this, probe statements
are added to the devicetree. This only affects NVME SSD and EMMC.
BUG=b:215040000
TEST=Build FSP with debug output enabled, and observe the correct root
ports being initialized depending on the FW_CONFIG values for BOOT_EMMC
and BOOT_NVME.
Cq-Depend:chromium:3397561
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I2ead505088f19fd3bf9768b541838395c82ef051
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Felix Held