When the board is in S3 and S5 the WLAN_DISABLE_L signal
can leak power into the WLAN power well since the GPIO
controlling WLAN_DISABLE_L is in the suspend well. Therefore,
drive WLAN_DISABLE_L low to avoid the power leak.
Change-Id: I1a0df80dd47fdbd535aca7a9d49253794c480606
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61421
Reviewed-on: http://review.coreboot.org/4358
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The name "LPDDR3PHY_CTRL_PHY_RESET_OFF" is not appropriate because the real
phy-reset is a low-active pin, so "off(0)" will trigger "start to reset".
To prevent confusion, we should rename the constants to "RESET_ENABLE" and
"RESET_DISABLE".
Change-Id: Iccba5ef3a2e992f877dea90741f0308c161758c9
Reviewed-on: https://gerrit.chromium.org/gerrit/61081
Tested-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/4357
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are needed to enable workarounds/features on specific
CPU types and stepping. The older northbridge function and
defines from sandybridge/ivybridge are removed.
Change-Id: I80370f53590a5caa914ec8cf0095c3177a8b5c89
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61333
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4355
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
To configure source clocks on Exynos 5420 for MMC drivers.
Some registers are different from the 5250. FSYS now has two parts
and MMC uses FSYS2. The MMC block uses MPLL as the clock source.
The "high-speed" MMC interface runs as 52MHz, so divider is set
accordingly.
Also, the MMC driver has changed from MSHCI (Mobile Storage Host Controller
Interface) to DWMCI (DesignWare MMC Controller Interface).
Change-Id: I9ba9cf43e2f2dcd9da747888c0c7676bd545177b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60858
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/4354
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Make use of google_chromeec_get_board_version to determine board
version, and apply proper RAM_ID table to load correct SPD.
Change-Id: I6a2d54759cf2ce98bf53df0db396c6e09368c714
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61192
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-on: http://review.coreboot.org/4353
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Update peppy's verb tables for the Realtek ALC283 Audio Codec.
ALC283 Configuration:
Digital Mic - NID 12h: Disabled
Speakers - NID 14h: Enabled
Mono out - NID 17h: Disabled
Mic 1 - NID 18h: Disabled
Mic 2 - NID 19h: Headphone Jack
Line1 - NID 1Ah: Internal Mic
Line2 - NID 1Bh: Disabled
PCBEEP - NID 1Dh: Enabled
SPDIF - NID 1Eh: Disabled
HP-OUT - NID 21h: Headphone Jack
Mic 1 doesn't seem to really be available, but the documentation
refers to NID 18h as MIC1, so it's being disabled as it's not
being used. The onboard microphone has been moved to line 1.
I had my peppy modified to attach the mic to line1 and mic1 now
works with this patch. Mic2 looks harder to rework, so I think
that will have to wait for the DVT boards.
Change-Id: I7d6ce6b428806b6aed1d36e7e25302fa5ae14b21
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/58880
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4352
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We will soon need to call google_chromeec_get_board_version to determine
correct DDR SPD. We must do so before DDR is initialized, so allow this
function to be called from romstage.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I882d84e38d11bf66067193a6f408f941f2cf8a81
Reviewed-on: https://gerrit.chromium.org/gerrit/61191
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4351
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
USB2 Port A set to 6.4" and Back Panel
USB2 Port B set to 5.2" and Back Panel
USB2 Port C set to 12.3" and Internal
Other devices all set to Internal.
build and boot on falco and check settings.
Based on the config settings all ports end up with
tuning param 1 == 5 and param 2 == 2
U2ECR[0] = 0x00059501
U2ECR[1] = 0x00059501
U2ECR[2] = 0x00059501
U2ECR[3] = 0x00059501
U2ECR[4] = 0x00059501
U2ECR[5] = 0x00059501
U2ECR[6] = 0x00059501
U2ECR[7] = 0x00059e01
Change-Id: I6b9e6df2679036a501355e6b389a486a6f178f99
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61297
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4350
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Systems are hanging in dev_configure() without a log to
indicate which device is being processed. Add some logging
points to save the device path before talking to the device
so we can narrow in on which device is the problem.
Change-Id: I3751c19a1ea68cdccbc33e4f6b2eeddd1bd9f2e4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61296
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4349
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This CPU does not support Configurable TDP and so far does
not need to use Controllable TDP.
Change-Id: I15599cd4e6890dd5c9d9f99bc4e95307a8dcc827
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60657
Reviewed-on: http://review.coreboot.org/4347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I7252925ef5c4efb69cad6b6fa179031162cf8e74
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/61058
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4346
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When dealing with DMA, we need a function to invalidate cache without corrupting
contents on main memory (clean).
Change-Id: I28e632ae57a7b7ed1accee74e76045b92f92a699
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61078
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4345
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The OP assigned by dcache_clean_by_mva must be handled in
dcache_op_mva.
Change-Id: Ib32262f0419453b2690d7c1a1c6602380b46a37f
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61077
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4344
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The OP assigned by dcache_clean_by_mva must be handled in dcache_op_mva.
Change-Id: Ia7631a08be6afacb13dfff406ac4db20efc98926
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61076
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/4343
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The is_resume comment is wrong for this board. It only applies
to the older 5250 cpu. In fact, the is_resume parameter
is not needed for ddr init and will likely be removed soon.
Change-Id: I4e3c92fcaaa75d3c9223d90acccf053f61406307
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/60103
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4342
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some new fields were added to the edid data structure, and the edid code was
changed to put estimated values into those fields which were ultimately passed
into depthcharge or other payloads. On snow we do things different and just
declare an edid structure statically which didn't have those members. The rows
and columns of the graphics console were 0, and that confused the framebuffer
driver and made it loop forever.
Change-Id: I6ca3bd948482b347a6a981e83b82b10dca995e5e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/61057
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4341
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Update RAM_ID table.
- Add DEVSLP0 signal to NGFF SATA port.
Note: After this change, old Micron 2GB boards will no longer boot.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Id68a1d6ace2702cca9c37305726cd55a0bde5005
Reviewed-on: https://gerrit.chromium.org/gerrit/60167
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Dave Parker <dparker@chromium.org>
Reviewed-on: http://review.coreboot.org/4340
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I9791beff44535a0a130292414fcd9875b497b1ca
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4492
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
No ROMCC involved, no need to include .c files in romstage.c.
Change-Id: I8a2aaf84276f2931d0a0557ba29e359fa06e2fba
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4501
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
walkcbfs() is used only with ROMCC. Besides finding stages during the
bootblock, it's also used when applying microcode updates during the
bootblock phase. The function used to return only a pointer to the data of
the CBFS file, while making the header completely inaccessible. Since the
header contains the length of the CBFS file, the caller did not have a way
to know how long the data was. Then, other conventions had to be used to
determine the EOF, which might present problems if the user replaces the
CBFS file. This is not an issue when jumping to a stage (romstage), but can
present problems when accessing a microcode file which has not been
NULL-terminated.
Refactor walkcbfs_asm to return a pointer to the CBFS file header rather
than the data. Rename walkcbfs() to walkcbfs_head(), and reimplement a new
walkcbfs() based on walkcbfs_head(). Thus current usage of walkcbfs()
remains unaffected.
The code has been verified to run successfully under qemu.
Subsequent patches will change usage of walkcbfs() to walkcbfs_head where
knowing the length of the data is needed.
Change-Id: I21cbf19e130e1480e2749754e5d5130d36036f8e
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4504
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
During the update_fit step, 'file_length' is used to determine how many
bytes are left in the CBFS file. It was decremented in a loop from an
array 'mcus[num_mcus].size', but 'num_mcus' was incremented right before.
Since 'mcus' is memset(0) externally, 'file_length' was never decremented.
The loop exited when it reached a dummy terminator, usually 48 bytes of 0
which are internationally added to microcode blobs in coreboot. However,
if that terminator is removed, the loop doesn't stop and continues until
it segfaults.
Change-Id: I840727add69379ffef75b694d90402ed89769e3b
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4508
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
If the unpacking was interrupt by Ctrl-C, probably part of
an archive is unpacked. If we run buildgcc again, the
incomplete folder would be and skipped.
We can create a file to tell the script the unpacking is done.
Change-Id: Id9eb74d119e22b62c70dca9b38a92c3dbdf0f64c
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4512
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The architecture information has been added to the folders to
build archives for crossgcc. We need to change the .gitignore
to keep ignoring them.
Change-Id: Ic18685e507f1b09088120eee6047d49141e29906
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4513
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
I am planning to write a document for new man, helping them to build a
working image from knowing nothing about Coreboot. The previous
LinuxBIOS-AMD64.tex was a good script.
LinuxBIOS was a out-of-date name. It needs to be changed it to Coreboot.
And the new document is not specific to AMD, so we get rid of the AMD64 from
the file name.
This is a separate patch for the renaming.
LinuxBIOS-AMD64.tex was still about SVN and buildtarget. Later patch
will come up for updating those old thing. And this new document,
CorebootBuildingGuide.tex, is planning to be only about building.
Navigating the source code is moved to later advanced document.
Change-Id: Ia8a2fd9db51e9870c1d645067bcfdc91ae1bf90a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4487
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Make boards take less vertical space, and link to board pages
Change-Id: Ifdd062a15191809b75422416c874161d9114363d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4493
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Instead of having global variables put them on the stack.
Change-Id: I462e3b245612ff2dfb077da1cbcc5ac88f8b8e48
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4288
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
It was suggested to eliminate the lock for sprintf. One way to do it is
to make the fake tx_byte into a closure. This patch allows it.
It's a bit tricky since we need to preserve compatibility with romcc.
Change-Id: I877ef0cef54dcbb0589fe858c485f76f3dd27ece
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4287
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These were terribly under-documented
Change-Id: I285ea083110d87076281e81065f5f38d0c688358
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4491
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Newer mainboards that use haswell -- and, presumably, chipsets to come -- need
some support functions. Add them in the drivers/intel/gma directory.
Currently, this is one file: intel_ddi.c, but more may come.
Compilation of this file is controlled by INTEL_DDI, defined
in the Kconfig as default n and used in the Makefile.inc
Change-Id: I501ee291c0d4589925ed3e478f67106337fcad31
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/60612
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4337
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We use junit style output these days.
Change-Id: I4110ec10bf0e9f4354ee08e7e1c5a81ae605fee0
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4484
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add ACPI Methods to enable and disable power limiting with PL1.
This can be used in ACPI Thermal Zone or in EC ACPI _QXX events.
This commit adds new unused methods and is fully tested with the
subsequent commit that makes use of these methods.
Change-Id: I9d8d23bfe9cf7c756ff8ab0412e5a010826b12db
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60546
Reviewed-on: http://review.coreboot.org/4334
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
1) fix enable of power aware interrupt routing
2) set BIOS_RESET_CPL to 3 instead of 1
3) mirror PKG power limit values from MSR to MMIO on all SKUs
4) mirror DDR power limit values from MMIO to MSR
5) remove DMI settings that were from snb/ivb as they do
not apply to haswell
1) verify power aware interrupt routing is working by looking
in /proc/interrupts to see interrupts routed to both cores
instead of always to core0
BEFORE: 58: 4943 0 PCI-MSI-edge ahci
AFTER: 58: 4766 334 PCI-MSI-edge ahci
2) read back BIOS_RESET_CPL to verify it is == 3
localhost ~ # iotools mmio_read32 0xfed15da8
0x00000003
3) read PKG power limit from MMIO and verify it is the same
as the MSR value
localhost ~ # rdmsr 0 0x610
0x0000809600dc8078
localhost ~ # iotools mmio_read32 0xfed159a0
0x00dc8078
localhost ~ # iotools mmio_read32 0xfed159a4
0x00008096
4) read DDR power limit from MSR and verify it is the same
as the MMIO value (note this is zero based on current MRC input)
localhost ~ # rdmsr 0 0x618
0x0000000000000000
localhost ~ # iotools mmio_read32 0xfed158e0
0x00000000
localhost ~ # iotools mmio_read32 0xfed158e4
0x00000000
Change-Id: I6cc4c5b2a81304e9deaad8cffcaf604ebad60b29
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60544
Reviewed-on: http://review.coreboot.org/4333
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Limit power to 12W at 73C and remove limit at 68C.
To have the CPU consume maximum power it is necessary to stress
both the CPU and the GPU. Bastion (chrome.supergiantgames.com)
and/or webglsamples.googlecode.com can be useful for this.
Testing this properly requires a script to report the running
average power readings. The watch_power.sh script is attached
to this issue in the partner tracker.
1) Run watch_power.sh continuously:
localhost ~ # watch -n 0 bash -e /tmp/watch_power.sh
2) Start Bastion (or other stress apps). The power draw should
be close to 15W if under enough load.
3) Watch until temperature climbs above 73C and is caught by
the thermal zone 10 second poll, this can be sped up by blocking
or removing the fan.
4) The ACPI thermal zone states should change to reflect that
active[2] is now enabled and power consumption should drop to 12W.
5) Stop the stress apps and wait until the CPU cools off again,
enable the fan again if it was removed.
6) The ACPI thermal zone state should switch back to active[3].
Change-Id: Ie6714a8543d4f06edf8513086fc9c968273bdb23
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60545
Reviewed-on: http://review.coreboot.org/4335
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The elog code calculates flash offsets and their equivalent
addresses in the memory address space. However, it assumes
the detected flash size is entirely mapped into the address
space. This can lead to incorrect calculations. Add code
to allow ROM_SIZE to be less than detected flash size. The
underlying assumption is that the first ROM_SIZE bytes are
programmed into the larger device.
Change-Id: Id848f136515289b40594b7d3762e26e3e55da62f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60501
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4332
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The original intention was to only run UPDATE_FIT when a microcode file was
included in CBFS. This happens when either CPU_MICROCODE_CBFS_GENERATE or
CPU_MICROCODE_CBFS_EXTERNAL is selected, however, the makefile checked that
CPU_MICROCODE_IN_CBFS was selected instead. The end result was that on
hasswell, the UPDATE-FIT step was always run, even when no microcode was
included, generating a build error.
Instead, introduce a new variable which tells if a microcode update is
added in CBFS during the build.
Change-Id: I28638912ed6f77761ef8a584f7636dc907b7a9b7
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4480
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
No need to show the choice of USB port or controller in case of older
hardware where location for usbdebug was hardwired.
Change-Id: Ia186bf2c6ed60be2834cf6fd0a1965c8bf81ed4d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4290
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Use a file in CBFS for keyboard layout and ethernet MAC instead
of scanning FMAP.
Change-Id: I7658c7c4e389deb20d7d8f57cce8b568efdc575d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4307
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Variables in coreboot and not in line with GRUB ones. E.g. HOSTCC is both
HOST_CC and BUILD_CC for GRUB (consult INSTALL for more details) and
what coreboot calls CC is TARGET_CC for GRUB.
Current code plugs this by defining variables explicitly but it has a nasty
effect that make stops caring about flags added in makefile itself. Undef
as many variables as possible but still pass them to configure for them to
have correct effect and keep CC assignment as my make version doesn't undefine
it even when instructed to do so.
Tested with qemu.
Change-Id: I9d18f557138a20ae3918d698dee8f5b5c5738f75
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4310
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The Intel GMA driver is in, this CL splices in the Makefile bits.
Change-Id: Icf42a537575b8cc90a679ec1fc15b09294630611
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/60346
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/4331
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
USE_XARGS mode builds n boards in parallel (with 1 CPU each) instead of
building 1 board with n CPUs.
This requires the main build system to work under such circumstances.
Change-Id: Ib4571a78dfe78fd61ae5b26c18be9745bd8b3d52
Reviewed-on: http://review.coreboot.org/4485
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This makes USE_XARGS-abuild unhappy due to races
Change-Id: I1237468366c7f8af7eacd572c2bd32df9a3d58ca
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4486
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
These functions are not all used yet, but do compile and are partially used
in the FUI testing.
They were extracted from the 3.4 kernel using coccinnelle filters. The .c files
are only compiled in if CONFIG_INTEL_DP is set.
Change-Id: Id95622a75aa02b496c9ea4717cb143394a8332e3
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/60245
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Aaron Durbin