It turns out that the exynos5-common code previously imported from
u-boot is not common code at all but very specific to the 5250 and
not compatible with the 5450. Hence, unify the directories exynos5250
and exynos5-common. We will try to factor out common code while
progressing with the 5450 port.
Change-Id: Iab595e66fcd01eda8365c96fb8bef896f7602f03
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3641
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch unfortunately incorporates a number of changes,
all of which are making future ARM ports easier.
- drop cruft that came in with u-boot
- move serial console from mainboard Kconfig to Exynos Kconfig
- factor out non-board specific wakeup code
- move generic bootblock code from mainboard to Exynos
- actually call arch_cpu_init()
- remove dead code
- fix up copyright messages
- remove snow_ prefix from a lot of code to reduce the noise
when creating a new mainboard based on that code.
Change-Id: Ic05326edf5a7e1a691c5ff841a604cb9e351b562
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3640
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In ram stage, all code flow should be tied to the resource allocator.
Stuff that has to happen before everything else goes into the mainboard
enable function in mainboard.c. This patch empties the main() wrapper
around hardwaremain.c, allowing to get rid of this special case in the
ARM port.
Change-Id: Ide91a23f1043b64acf64471f180a2297f0f40d97
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3638
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch moves ARM core and DRAM timing functions around to simplify
the dependencies for system_clock_init().
The original code was architected such that the system_clock_init()
function called other functions to obtain core and memory timings.
Due to the way memory timing information must be obtained on Snow,
which entails decoding platform-specific board straps, the bottom-
up approach resulted in having the low-level clock init code
implicitly depend on board and vendor-specific info:
main()
->system_clock_init()
-> get_arm_ratios()
-> CPU-specific code
-> clock_get_mem_timings()
-> board_get_revision()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
...then proceed to init clocks
...come back to main()
The new approach gathers all board and vendor-specific info in a
more appropriate location and passes it into system_clock_init():
main()
-> get_arm_ratios()
-> CPU-specific code
-> get_mem_timings()
-> board_get_config()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
-> system_clock_init()
...back to main()
Change-Id: Ie237ebff76fc2d8a4d2f4577a226ac3909e4d4e8
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2271
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
