The romstage code for rambi uses the mmio way of reading
inputs. However, this is a problem is the GPIOs are set up
as legacy mode. Subsequent warm resets mean the ram_id is
read incorrectly. Ensure the ram_id is read consistently
by keeping the GPIOs for ram_id in mmio mode.
BUG=chrome-os-partner:24085
BRANCH=None
TEST=Built and booted. And rebooted. Now seeing consistent ram_id
values on warm resets.
Change-Id: Ieff98c000be80998854f325754f1e819975d2be5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177230
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4977
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The default mode of the SPI controller has prefetching disabled.
That obviously has a performance impact. Enable both caching
and prefetching to make booting faster. This has a significant
impact on streaming data out of SPI.
BUG=chrome-os-partner:24085
BRANCH=None
TEST=Built and booted rambi. Payload loading step went from ~285ms
to ~54ms.
Change-Id: I065cf44e1de7dcefc49aa9ea9ad0204929ab26f4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177220
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4976
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
When a pad is configured for direct IRQ it needs to be in
non-legacy. Additionally, the signal is passed directly to
the APIC by setting the LEVEL and TPE bits in the pad config
register. The APIC can then be configured for level, edge,
and rising/falling.
BUG=chrome-os-partner:24037
BUG=chrome-os-partner:22863
BRANCH=None
TEST=Built and booted with this config. Trackpad is firing interrupts
more than it should, but it appears to be a trackpad firmware
and/or configuration issue.
Change-Id: I00042b2ddba67d6bf23f0e7468d0719196e6f865
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176793
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4975
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The TPM needs to have the TPM_Startup command sent to it
on all boot paths. The call init_chromeos() in romstage_common()
fulfills this requirement.
BUG=chrome-os-partner:24057
BRANCH=None
TEST=Built and booted. Was able to suspend to ram multiple times
in a row.
Change-Id: Id0339a9d82897249d20ff5f62d2dcb8b535310fa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176803
Reviewed-by: Todd Broch <tbroch@chromium.org>
Tested-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4974
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Some of the drivers in the kernel were not so happy about
having shared IRQs. Also, sharing IRQs means more code
needs to be run in interrupt context to determine if the IRQ
was meant for a particular device. Fix this.
No more 'mmc1: got irq while runtime suspended' messages.
BUG=chrome-os-partner:24056
BRANCH=None
TEST=Built and booted. Looked at /proc/interrupts and noted no
more sharing between pci devices.
Change-Id: Ie5da102204ffe3156dd55ab17af77df245a57c97
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176792
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4973
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
ITE Super I/O's make use of this method to enter and exit in and out of
their PNP configuration. Provide functions for use in ram stage
component.
Change-Id: I2b546c2b17eefc89aaab4982192f5e9a15a16c2f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5666
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
The PCIe subsystem was constantly waking up boards from
S3 and S5. Completely disable PCIe wake ups. It can be made
mainboard-configurable later if needed.
BUG=chrome-os-partner:24004
BRANCH=None
TEST=Both S3 and EC RW->RW update (trip through S5) don't
cause wakeups.
Change-Id: I922e2947c4b6e29277d913f06192601a2954f8fe
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176791
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4972
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Previously pads were being configured as both input and output
simultaneously due to the config bits being active low. Create new
defines that only enable either input or output, and use them in our
GPIO configs.
BUG=chrome-os-partner:22863
TEST=Manual on Rambi. Verify system boots and peripherals still
function.
BRANCH=None.
Change-Id: If386682a3d810864b7b9f5d2aecdb2e6cfceea86
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176725
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4971
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The kernel chromeos_laptop driver nomenclature expects the
board name to not be in all caps. Fix this as well as the i2c
address for the trackpad.
BUG=chrome-os-partner:24307
BRANCH=None
TEST=Built and booted. trackpad device is found. IRQs still not
working yet.
Change-Id: Id6be8ee4bce2835e303ea4fe63944be80d2d7ec2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176680
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4970
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This commit does the common parts for all LPSS devices
that are enabled: enable snoop in IOSF and enable power
management. Additionally, the i2c devices are taken out of
reset.
BUG=chrome-os-partner:23790
BRANCH=None
TEST=Built and booted with modified kernel-next. I2C bus devices
show up and I see 0x10 on one of the buses.
Change-Id: I540caea6a8666f5684dc5cee683a6b085dfac6de
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176424
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4969
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add the LPSS IOSF port access to reg_script. This is
going to be used by baytrail.
BUG=chrome-os-partner:23790
BRANCH=None
TEST=Buit.
Change-Id: I0367acdb584f2de0bb871b136042b57fe6b7ec90
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176423
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4968
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The eMMC device is initialized as version 4.5 with HS200 speeds.
BUG=chrome-os-partner:23966
BRANCH=None
TEST=Built and booted rambi to login screen off of eMMC device.
Change-Id: I686c6136005fcb2587b939ddea293f4398df9868
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176536
Reviewed-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4967
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The SSC (storage control cluster) houses the SD, SDIO, and eMMC
interfaces. The scc cofniguration function, baytrail_init_scc(),
is ran in the pre device stage to initialize the SCC. The eMMC
is expected to be configured for version 4.5.
BUG=chrome-os-partner:23966
BRANCH=None
TEST=Built and booted with some other eMMC changes into login screen off
of eMMC device.
Change-Id: I81cc755a790b7e43ad234a8201dae480277202c8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176535
Reviewed-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4966
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The SCORE allows controlling the pad configuration while
the SSC handles the configuration for the storage control
cluster.
BUG=chrome-os-partner:23966
BRANCH=None
TEST=Built.
Change-Id: Ifd9f67a4e88d5bb99faec6ceeb3e263001a87c41
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176533
Reviewed-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4964
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Also add the relevant info about these pins to the ASL tables + add
SMBIOS type 41 data for these parts.
BUG=chrome-os-partner:22863
TEST=Manual on Rambi. Set some pins to GPIO_DIRQ, and then verify DIRQ
regwrites w/ GPIO_DEBUG look correct.
Change-Id: Id40655f9fb2ea7b10e1ff58d0b2a8b4cc6f05ff8
Reviewed-on: https://chromium-review.googlesource.com/176299
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4963
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Make all three coreboot stages (bootblock, romstage and ramstage) aware of the
architecture specific to that stage i.e. we will have CONFIG_ARCH variables for
each of the three stages. This allows us to have an SOC with any combination of
architectures and thus every stage can be made to run on a completely different
architecture independent of others. Thus, bootblock can have an x86 arch whereas
romstage and ramstage can have arm32 and arm64 arch respectively. These stage
specific CONFIG_ARCH_ variables enable us to select the proper set of toolchain
and compiler flags for every stage.
These options can be considered as either arch or modes eg: x86 running in
different modes or ARM having different arch types (v4, v7, v8). We have got rid
of the original CONFIG_ARCH option completely as every stage can have any
architecture of its own. Thus, almost all the components of coreboot are
identified as being part of one of the three stages (bootblock, romstage or
ramstage). The components which cannot be classified as such e.g. smm, rmodules
can have their own compiler toolset which is for now set to *_i386. Hence, all
special classes are treated in a similar way and the compiler toolset is defined
using create_class_compiler defined in Makefile.
In order to meet these requirements, changes have been made to CC, LD, OBJCOPY
and family to add CC_bootblock, CC_romstage, CC_ramstage and similarly others.
Additionally, CC_x86_32 and CC_armv7 handle all the special classes. All the
toolsets are defined using create_class_compiler.
Few additional macros have been introduced to identify the class to be used at
various points, e.g.: CC_$(class) derives the $(class) part from the name of
the stage being compiled.
We have also got rid of COREBOOT_COMPILER, COREBOOT_ASSEMBLER and COREBOOT_LINKER
as they do not make any sense for coreboot as a whole. All these attributes are
associated with each of the stages.
Change-Id: I923f3d4fb097d21071030b104c372cc138c68c7b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5577
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
Add support for DirectIRQ / dedicated IRQs. This consists of up to 16
IRQs for both SCORE and SSUS banks.
BUG=chrome-os-partner:22863
TEST=Manual on Rambi. Set some pins to GPIO_DIRQ, and then verify DIRQ
regwrites w/ GPIO_DEBUG look correct.
Change-Id: I4b0dc6e7ae86c9f554b6e78792239234f702764c
Reviewed-on: https://chromium-review.googlesource.com/176165
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4962
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
For some reason HDA can now be disabled. It's unclear what changes
in the baytrail code allowed this to happen, sadly.
BUG=chrome-os-partner:22871
BRANCH=None
TEST=Noted hda is not in lspci.
Change-Id: I64e2560533be6f701fa66cd53c906b62b09012ed
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176394
Reviewed-on: http://review.coreboot.org/4961
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Rambi has 3 pins that need to be configured for SCI and SMI:
1. GPIO_CORE[0] - runtime SCI pin
2. GPIO_SUS[7] - SMI for firmware lid events
3. GPIO_SUS[0] - wake pin for S3 wakes from EC.
Configure these pins now that the rest of the infrastructure
is in place. The one thing that is yet to work is runtime SCI
for lid events once booted.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=built and booted. lid close at rec screen works. And wake
from S3 with a keyboard press works.
Change-Id: I5f8e38ec5f4cf1a8ef7aa7fcee9abc344d9b184f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176393
Reviewed-on: http://review.coreboot.org/4960
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
As rambi is a baytrail board it doesn't have a dedicated wake pin.
Therefore, one needs to enable the proper GPIO to wake up the sytem
before going into S3.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Put system into S3. Keyboard press created wake event. Also, typed
'lidclose' on EC console while at recovery screen. Machine properly
shutdown.
Change-Id: Ic67b6bce93d57c620f498505d83197e4ae34a07d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176392
Reviewed-on: http://review.coreboot.org/4959
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
GPIOs which trigger SMIs only set the status bits in the ALT_GPIO_SMI
regier. No bits in the SMI_STS register are set. Therefore, the
ALT_GPIO_SMI register needs to be read and cleared on every SMI.
Additionally, the mainboard_gpi_smi() handler needs to be called as
well on every SMI because of this property.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted to recovery screen. Typed 'lidclose' on EC
console. SMI occurred which caused the board to be shutdown.
Change-Id: Ic204d8b928a0cb4f51f108a649f374d9f94e4f47
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176391
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4958
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
In order for gpio pins to trigger an smi/sci the GPIO_ROUT
register needs to be set accordingly. For SMI, the ALT_GPIO_SMI
register needs to be enabled for each gpio as well.
The first 8 gpios from the suspend and core well are the only gpios
that can trigger an SMI or SCI. The settings for the GPIO_ROUT
and ALT_GPIO_SMI register are not commited until the SMM settings
are enabled in the southcluster.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted. Manually triggered SCI by changing GPE0a_EN
and toggling PCH_WAKE_L on the EC console.
Change-Id: Id79b70084edc39fc047475e984494c224bd75d6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176390
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4957
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The gpe0 block's size was being misreported. Correct
the gpe0 size and use make the FADT fields be more
robust instead instead of hand calculating fields that
are the based on the same size.
This change correctly enables GPE events in the kernel.
Confirmed this by using iotools read the gpe_cnt register.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted. Confirmed EC's GPE event is enabled (but
still not working).
Change-Id: I415710f7fec2e95cecee3bf679ee673dacc27480
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176271
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4956
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
- C-state table based on static config
MWAIT values are from ref code for non-S0ix config
C6 substate 8 is ignored by the kernel as it violates the CPUID
but it is left in as the other substate may not work.
- P-state table generated with proper ratio and VID values
relies on having the package power msr set to magic value
as the power-on default is wrong
- T-state table uses static table
BUG=chrome-os-partner:23505
BRANCH=rambi
TEST=build and boot on rambi
Change-Id: I7c997e58cb3a71d0ec413b17f0c5467bef4bf62c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175742
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4954
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The bus clock speed is needed when building ACPI P-state tables
so extract that function and have the value be saved in pattrs.
The various IACORE values are also needed, but rather than have
the ACPI code to the bit manipulation have the pattrs store an
array of the possible values for it to use directly.
BUG=chrome-os-partner:23505
BRANCH=none
TEST=build and boot on rambi
Change-Id: I5ac06ccf66e9109186dd01342dbb6ccdd334ca69
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176140
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4953
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
As far as I can tell turbo enabling behaves like
it did on haswell so use the standard code.
There are also some magic values to set in some magic
MSRs related to turbo and package power so they report
correctly.
The L2 cache shrink is enabled and a threshold is set
that makes both dual and quad core happy.
C1E is disabled to match the reference code.
BUG=chrome-os-partner:23505
BRANCH=rambi
TEST=build and boot on rambi
Change-Id: Ic6d4283d480a44d85a9b96571baf83928615665c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175743
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4952
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This required changing value/mask types to uint64_t.
Another option would be to use id field to select low or high
32 bits of the MSR and set them independently.
BUG=chrome-os-partner:23505
BRANCH=none
TEST=build and boot on rambi
Change-Id: Ied9998058a8035bf3f003185236f3be3e0df7fc9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176304
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4951
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The superio.asl file allows for the mainboard to hang
devices off of the LPC bus in ACPI. Include the keyboard
controller, EC memory map, and host interface's resources.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted. Noted resource reservations in dmesg.
Change-Id: Ida6481cd4c4725b5d3946bc64179ee99c93b0106
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176134
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4950
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The mainboard needs an opportunity to hang devices off of
the LPC device. Therefore, provide this opportunity for the
mainboard.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Buit and booted with keyboard. Keys work.
Change-Id: Ie2b660ad43e86d9237b0b0bb0720b069670bc537
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176133
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4949
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Fix the SMI and SCI gpios for Rambi. Also, add in the
EC callbacks for the SMI handler. Note that the handler
for GPI SMIs has not been tested yet as baytrail chipset
code doesn't yet support setting up those configurations
yet.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Noted that SCI was enabled in /sys/firmware/acpi/interrupts
for the EC's SCI GPI. Also was able to see Chrome EC messages
with CONFIG_DEBUG_SMI and powering down at the dev screen.
Change-Id: I67b278fd38e1c09271d2c1e16e42f6e8c49e3a70
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176077
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4948
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The IRQs used for devices that are in acpi mode are added as well
as the IRQ defitions for the dedicated GPIO IRQ routing.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built.
Change-Id: I2eed5a4584e2d908c32617c9289a2abeaa30bd44
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176120
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4947
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Baytrail has a configurable SCI irq. Add support for
properly configuring SCI irq. Note that it is currently
fixed to IRQ9, but the code supports setting it to the
other supported values. The current mainboards using
baytrail defer the madt IRQ override information to the
chipset.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted. Noted 'SCI is IRQ9' message.
Change-Id: I7b307bd58f9de944f0cb4c116107a15345499f2e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176075
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4946
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
These changes to the eMMC pads allows the kernel to see the
eMMC device. One is able to install onto the eMMC device, and
the kernel is loaded and booted from eMMC device. Note, that
it may not fully boot because of other issues such as
not-completely working ACPI support.
BUG=chrome-os-partner:22580
BRANCH=None
TEST=booted off of usb drive. can see eMMC device.
Change-Id: I9c088398297a0b559383bdf4a389dd19a1110e0f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176073
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4945
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
For some mysterious reason GPIO_S0_NC22 is making the eDP panel
go entirely white when it is configured with internal pullup.
Since these (supposedly XDP related) pins are unknown functionality
lets set them to GPIO_DEFAULT instead of GPIO_NC.
Additionally the VBIOS is being changed to issue int15 callback
to determine the boot graphics device. If we list both LFP and EFP
then the dev/rec screens will show on the panel when HDMI is not
attached and otherwise will display on HDMI.
BUG=chrome-os-partner:23507
BRANCH=rambi
TEST=build and boot on rambi, see firmware/kernel screens on the panel
when HDMI is not attached, and firmware screens on the panel and
kernel screens on both when HDMI is attached.
Change-Id: Ieb05a591d63c4f8e09fa154eeb76004d32579508
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175952
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4944
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Previously the only path through memory init and coreboot was
hardcoding S5. Therefore all S3 paths would not be taken. Allow
for S3 resume to work by enabling the proper control paths in
romstage.
BUG=chrome-os-partner:22867
BRANCH=None
TEST=While in kernel 'echo mem > /sys/power/state'. Board went
into S3. Power button press resumed back into kernel.
Change-Id: I3cbae73223f0d71c74eb3d6b7c25d1b32318ab3e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175940
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4943
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
linux/drivers/platform/x86/thinkpad_acpi.c looks for an EC
version string before loading, this code copies the vendor BIOS by
exposing this string. This was originally part of x60's mainboard.c
Change-Id: I5e54ea2833252bc4dbba46ceb67d78c435b34845
Signed-off-by: Trevor Mosey <uberushaximus@gmail.com>
Reviewed-on: http://review.coreboot.org/5638
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The FADT for baytrail had incorrect offsets leading to
the kernel spewing a huge mess of ACPI errors. Fix these offsets
to be initialized in the chipset code.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted into kernel on rambi. Login screen comes up.
Change-Id: I89fc2a4fd800ff01cedf89b51cfb1369aceb9f03
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175663
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4941
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This provides the initial support for interrupt routing
in bay trail. It includes both acpi changes and board changes
to ensure the interdependencies are met with the current ASL
code. The PIRQ routing is handled by the mainboard exporting
an irqroute.h header that describes the per device and PIRQ
PCI settings.
There are still a lot of ACPI errors in the kernel with this
change, though.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted rambi into kernel.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Id8a865a24fc8d49743c0b54efdb64aaef52fcd8e
Reviewed-on: https://chromium-review.googlesource.com/175700
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4940
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The mp_init library was based off of haswell code, but baytrail
was the first chipset to take advantage of it. Move haswell over
to using it so that the code duplication can be removed.
Change-Id: Id6e9464df028aa6ec138051f925817c85b4c13e5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5413
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
In the signature of the function `hexdump32()` it does not make sense to
represent a length, assumed to be positive, as a signed integer.
With this change, it is no longer necessary to cast a pointer to
unsigned long when passing it to `hexdump32()`.
The same change for the function `hexdump()` was done in commit
3dd0e72d [1].
lib/hexdump: Take const void * and size_t as arguments
[1] http://review.coreboot.org/4575
Change-Id: Id97f5daff95f94e862ee8b5be896a6629b125a13
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5646
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The coding style requires to use tabs for indentation and not spaces.
Use GNU indent 2.2.11 with the switch `-linux` to indent the file,
which also removes the empty lines at the end of the file.
Change-Id: I874f178e50d7558d3299026aec2771ad45f88d8e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/4576
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Heap allocation begins with BIOS_HEAP_MANAGER, no need to clear
the fields individually.
Change-Id: Ia1af84bd09d1edf8f72223752557d44a96dec6e1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5659
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Backported from fam15tn and fam16kb.
This also implements GetHeapBase() to satisfy some requirements
of HAVE_ACPI_RESUME for the following boards:
amd/inagua
amd/south_station
amd/union_station
asrock/e350m1
Change-Id: I488d063d4eabf4bf45bcbabd1e8f13b88b2ef401
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5658
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Backported from fam15tn and fam16kb.
Change-Id: I868352b32ff56a8386c615ab1a9f59e7e875292e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5657
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
These function prototypes to remain identical across all
AGESA families.
Change-Id: If2a0a08fa7122e6becded37d032d3c40bde2d149
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5656
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
While fam15 boards do not select HAVE_ACPI_RESUME, backport this
from fam14.
Implementation of this function is common across different families.
Change-Id: I222b418a0a79bbdf5f5cce6c876243ecb4912256
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5655
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Aaron Durbin