Add support to override SPI fast speeds based on board version from both
bootblock and verstage. Overrides apply for Guybrush only and SPI speed
is overridden from 66 MHz to 100 MHz starting board version 4. This will
help to improve the boot time on board version by ~60 ms and still allow
the old boards to boot with 66 MHz.
BUG=b:199779306
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5bf03ab8772f27aca346589e9c5662caf014d0d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add support to override SPI ROM fast speed based on board version. This
will allow boards to start at lower speeds during bringup and then
switch to higher speeds after assessing the signal integrity. Also
implement a default no-op override.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ia8ff3b3bdb53fee142527ae63aa7785945909304
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Currently all SPI speed configurations are done through EFS at build
time. There is a need to apply SPI speed overrides at run-time - eg.
based on board version after assessing the signal integrity. This
override configuration can be carried out by PSP verstage and bootblock.
Export the APIs to set and read SPI speeds from both PSP verstage and
bootblock.
BUG=None
TEST=Build and boot to OS in guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I281531e506b56173471b918c746f58d1ad97162c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
eSPI is setup in two different locations in bootblock depending on early
port80 routing configuration. Also eSPI is setup in PSP, if verified
boot starts before bootblock. Consolidate all the scenarios by
initializating eSPI very early in fch_pre_init if verified boot starts
after bootblock and eSPI is enabled.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Icfeba17dae0a964c9ca73686e29c18d965589934
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the GPIO mux/control MMIO regions are within the ACPIMMIO region,
we need to call enable_acpimmio_decode_pm04 here first so that accessing
the GPIO registers will work.
BUG=None
TEST=Build and boot to OS in Guybrush.
Change-Id: I4bc076261c72cf999a5f2464b74cff6bf694d473
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tracker is a debugging tool, include AP/INFRA/PERI tracker.
When bus timeout occurs, the system reboots and latches some
values which could be used for debug.
Signed-off-by: Zhenguo Li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Change-Id: I82f8e6e5f8ccb7f8246cae45a01a3ddd5f2966f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58244
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tracker is a debugging tool, include AP/INFRA/PERI tracker.
When bus timeout occurs, the system reboots and latches some
values which could be used for debug.
Signed-off-by: Zhenguo Li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Change-Id: If457f4a096cd63038bf6b40552aa3caaba33d5fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58243
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is the wrong register offset printed in the debug log when the
data register is written:
'lpc_tpm: Write reg 0x18 with 0xnn' should be
'lpc_tpm: Write reg 0x24 with 0xnn' for data FIFO access.
This can be confusing when searching for issues with the help of the
TPM debug messages since the code itself is correct. Fix this error.
Change-Id: Ic28ee5a07146e804574b887ea05c62e7e88e9078
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Some poppy variants did not select a system type, which led to the
default desktop type being set. Select the best fit enclosure type
for each variant.
Alphabetize the variant-specific options for improved readability.
Change-Id: I7c23f8fa3ae1de67f7a68b8a4e9ec16c4e8044df
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Make use of the newly introduced ACPI macros for CPPC table generation
that currently exists of a bunch of confusing assignments of structs
that only get partially filled.
Test: dumped SSDT before and after do not differ.
Change-Id: I844d191b1134b98e409240ede71e2751e51e2159
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lance Zhao
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Since the DRAM population is fixed to both channels on all mc_ehl boards
there is no need to have this 'half_populated' variable at all.
Simply use a fixed 'false' in the call of 'memcfg_init()' and delete
this variable here.
Change-Id: I783c17e6d92322a8b0c094cce803108e718011fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The preferred location for the SPD data on mc_ehl based boards is the
HW-Info data structure. Inside this structure there is a field of 128
bytes available for the SPD data. So in order to use it construct a
buffer in memory which is 256 bytes long (as FSP requests minimum 256
bytes for the SPD data) and where the upper 128 bytes are taken from
HW-Info holding the needed timing parameters for LPDDR4.
If there is a case where HW-Info is not accessible or where the
contained SPD data is not valid (by checking the CRC in HW-Info SPD)
fall back to fixed SPD data set in CBFS.
Change-Id: I2b6a1bde0306ba84f5214b876eaf76ca12d8f058
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
1. Samsung K4U6E3S4AB-MGCL
BUG=b:202480992
TEST=emerge-dedede coreboot
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I811f32defd50a940a09f238d38c962d2caf42855
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
For 1 bit long bit fields an unsigned type should be used. In this case
uint32_t is used instead of a generic unsigned int for both consistency
reasons with the rest of the file and to clarify that the bits will be
packed into a 32 bit memory location.
TEST=Resulting image of a timeless build for google/guybrush results in
identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic630d1709174d90336746bc37da504437c12643c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Replace the dt option `PmTimerDisabled` with use of the Kconfig option
`USE_PM_ACPI_TIMER` for enabling/disabling the PM Timer.
A default value representing the prior devicetree value was added to the
boards system76/{lemp10,galp5,darp7}, so this change will not alter
behaviour.
Change-Id: If1811c6b98847b22272acfa35ca44f4fbca68947
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Fix include of nvs.h to reflect commit 661ad4666c (ACPI: Select
ACPI_SOC_NVS only where suitable); and re-add <device/pci_ops.h>,
removed in commit 0aad0531dc (util/autoport/bd82x6x.go: Drop unused
includes), as the generated early_init.c uses pci_write_config16().
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Change-Id: Ic1e97cfa7dce0e4d25f7a37c28d3635bdbf6c2a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Set PKG_CST_CONFIG_CONTROL MSR bit 15 to make bits 15:0 read-only.
Change-Id: Ia196906d3c2636742ae90160a224354e8df7863a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add a space before the `*/` C-style comment ending.
Change-Id: Ic8928286c8237808b9e380e4393078792589615d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Update MAX98360 ACPI HID from "MX98357A" to "MX98360A"
BUG=b:198716348
TEST=Build nipperkin, codec is functional with new machine driver.
Cq-Depend: chromium:3195465
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: I8a1155848856db0cc4f42cfee0d914f8d1186b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
coreboot normally owns PCIe resets for all Cezanne based systems.
However during S0i3 resume coreboot cannot intervene for S0 GPIOs
(S5 carry over fine) so we needed an alternate way to de-assert
this reset on guybrush. This change feeds in the given S0 reset
GPIO (69 in this case) so that SMU may de-assert this reset on
S0i3 resume.
BUG=b:199780346
TEST=With latest FSP verify SD device trains each of 10 cycles
Cq-Depend: chrome-internal:4157948
Change-Id: Ieee31651db30147fda84ee1aa31df7cb1c206356
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58198
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update UPD to include option for FSP to de-assert PCIe reset GPIOs as
specified in the DXIO descriptors. This change requires FSP version
1.0.4 revision 2 otherwise setting this value does affect any FSP
behavior.
BUG=b:199780346
TEST=Verify toggling this value is reflected in FSP
Cq-Depend: chrome-internal:4170351
Change-Id: I0dee05fb0a650f026c2f09581117fa7fb5f6a90a
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Document what setting the PM_ACPI_S5_LPC_PIN_MODE and
PM_ACPI_S5_LPC_PIN_MODE_SEL bits causes. The corresponding code will
eventually be factored out and moved to the Cezanne SoC code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I10e3eee5cfc1c5ba2c88b8b7e83e96e481f787e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since the LPC_LDRQ0_PD_EN gets set right after it got cleared, we can
remove the clearing of that bit. This is split off from the previous
patch to be able to use timeless build to verify that the previous patch
didn't change any behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieb300e7c7ce7e74c32ebdade0360ee4bd499b11a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
It's hard to understand what this code is doing because it uses hard
coded values, so use the register and bit defines instead.
BUG=none
TEST=Timeless build for guybrush results in identical binary.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2d74ed3b9b4984ab1e2a22c50375baf9c9589df0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Register and bit definitions are from the Cezanne PPR #56569 Rev 3.03.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib109efe679560604ff8209b4177611eb2aa9ebdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The definitions of bit 9 and 10 somehow got swapped between Picasso and
Renoir/Cezanne, so put those in the Cezanne-specific header file. The
reference code writes the same values to the raw bits in both, so we
probably would still get away with putting this into the common header,
but it's better to keep the defines consistent with the documentation in
all cases.
Register and bit definitions are from the Cezanne PPR #56569 Rev 3.03
and cross-checked to be compatible with the Picasso PPR #55570 Rev 3.16.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3a033d63eeb06eed6783e4c3797ad8dea490db8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Mock architecture can be used to build libpayload using host compiler.
It can be enabled by setting ARCH_MOCK=y in the dotconfig. It sets
LITTLE_ENDIAN=y, as most machines these days use little-endian CPUs.
Libpayload will use HOSTCC as CC, HOSTLD as LD, etc. instead of tools
provided by xcompile.
Mock architecture configuration can be used by payloads for testing
purposes. Thanks to it, tests can be architecture-independent,
and can be executed without requiring compatible Kconfig options,
e.g. ARCH_ARM64=y for ARM64 machine. However, one has to provide
implementation for most architecture-specific functions present
in arch/* directories.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Ie3a6e6f6cad2f8a2e48a8e546d3b79c577653080
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This change adds src/soc/* to subdirs before src/soc/*/* to allow
Makefile in src/soc/* to provide any common helpers that will be
useful for any src/soc/*/*. This is done to primarily ensure that the
helpers are defined before being invoked by the SoC Makefile.inc. This
is utilized by Intel CSE stitching mechanism in following changes.
BUG=b:189177580
Change-Id: I91579a87016fdc2b9ca2d798b81969c21c18b4a3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Fizz's USB ACPI code is intended to allow the OS to control port
charging power, but since Fizz's ports are dumb (vs smart), it
controls power to the port itself. The end result is that active
ports become disabled when rebooting from Windows (10/11), and
power is not restored until the device is powered down (a warm
reboot is not sufficient).
Subsequent Chromebox models (eg, Puff-based variants) don't bother
with EC-controlled USB port power, so just drop it since it's
problematic and provides no benefit.
Test: boot Windows 10/11, reboot, observe active USB ports still
functional (eg, USB KB still works)
Change-Id: I2c13d49b3ce8de8b0a38512db3c57d0c8ecbf0ad
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Populate a memory_info struct with PEI and SPD data, in order to inject
the CBMEM_INFO table necessary to populate a type17 SMBIOS table.
On Broadwell, this is done by the MRC binary, but the older Sandy Bridge
MRC binary doesn't populate the pei_data struct with all the info
needed, so we have to pull it from the SPD.
Some values are hardcoded based on platform specifications.
Change-Id: I15e00a01121150b778cfa684b9147d0cac97beb8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
CB:57144 broke JUNIT_OUTPUT=y, and unit-tests were writing to stderr
instead of selected XML files, because test name used for XML file
creation contains test path. Build system did not create necessary
directiories, which CMocka required to create output files.
This commit fixes writing to XML files with JUNIT_OUTPUT=y, but had to
sacrifice path in test name, as it was causing a lot of problems
(because CMocka does not know, how to write multiple test groups to one
XML file, so it uses test group name [here __TEST_NAME__(test_group)] as
part of output filename).
Example:
Test: tests/lib/rtc-test
Output file:
`build/tests/junit-tests_lib_rtc-test(tests).xml
Change-Id: I09891aca923bf1271cafeaa09f89b6539022709c
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Caroline uses a Wacom digitizer, so adjust the ACPI HID
so that the proper drivers attach under Windows/Linux.
Change-Id: I732b09001dc41a91a32a5f9260abdab435b28b8a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Before attempting another commit 6260bf71 (vboot_logic: Set
VB2_CONTEXT_EC_TRUSTED in verstage_main), ensure that guybrush programs
GPIO_EC_IN_RW (GPIO_91) as an early GPIO so that it can be read from in
verstage.
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: Ia6dcb225bbca89f3a873aad75a7d67625cdd3742
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
1. Fix PCIe slot capabilities not being really read from an IIO root
port device. The Hot-Plug capability of IIO root port cannot be
enabled due to FSP limitation (v2.1-0.2.2.0), but the code should
reflect the true capabilities by reading the root port device's CSR.
2. Initialize the characteristics flags to 0 in the for-loop to fix the
issue of the flags values persists to the next iterations.
Tested=On OCP Delta Lake, dmidecode -t 9 shows the expected results.
For example without the fix it shows 'Hot-plug devices are supported'
but in fact it's not:
System Slot Information
Designation: SSD1_M2_Data_Drive
Type: x4 PCI Express 3 x4
Current Usage: Available
Length: Short
ID: 1
Characteristics:
3.3 V is provided
PME signal is supported
Hot-plug devices are supported
Bus Address: 0000:00:1d.0
With the fix it shows the correct result:
Handle 0x0016, DMI type 9, 19 bytes
System Slot Information
Designation: SSD1_M2_Data_Drive
Type: x4 PCI Express 3 x4
Current Usage: Available
Length: Short
ID: 1
Characteristics:
3.3 V is provided
PME signal is supported
Bus Address: 0000:00:1d.0
Change-Id: Iea437cdf3da5410b6b7a749a1be970f0948d92d9
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58100
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason, we have to adjust the PIR8
register (0x3150) which is responsible for PCIe device 25h. The bridge
is connected to PCIe root port 7.
The following routing is required:
INTA#->PIRQC#, INTB#->PIRQD#, INTC#->PIRQA#, INTD#-> PIRQB#
TEST:
- Boot into system software
Change-Id: Id6bb8d00458c4d1e3fefd01ac3848078355868d9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
In upcoming patches, we need mainboard specific adjustments.
Change-Id: Icf9d829b19b2d26a39ad34be4658064083e9da6d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Enable LPC ComB on this mainboard.
TEST:
- Boot Linux and check with 'dmesg | grep tty'
Change-Id: I7ec58685a723c177df18144011934b206e6425d0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This mainboard uses an eSPI-to-LPC bridge for console output. For this
reason, the internal LPSS UART must be disabled.
Change-Id: I86777cf719def331f4d257ddd94e9a87125ebce8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Set the GPIOs according to the circuit diagram for this mainboard.
Change-Id: I19dc24a16ee9f533b45879bf60fb441e24018cc8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This mainboard has only SATA Port 1 available with no device sleep
feature.
Change-Id: I338833f2f9bcb407599cfc676ead0b8a9d7379bd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This mainboard has SD slot available and therefore it should be enabled.
Change-Id: I0c97e2dc589bf6b89713a473925e42a20278f457
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This board has the RTC RX6110SA connected to the I2C2 instead of SMBus
as in mc_ehl1. Set the bus speed for I2C2 to 100 kHz, since this RTC
only supports the standard speed.
TEST:
- Console Log shows no errors for RX6110SA during I2C2 init
- Finalize device for I2C 00:32 shows correct date and time
Change-Id: I679c6397fa0d213a25eebaf8a9e0bda9941acd26
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Since this variant uses different DDR4 devices compared to mc_ehl1 in a
memory down configuration, the SPD data file must be adapted.
In a first configuration we use Micron MT53D512M32D2NP modules.
Following values were adjusted according to this board characteristic
and with help of Serial Presence Detect (SPD) for LPDDR3 and LPDDR4
SDRAM Modules JEDEC Spec and the Specification for this Micron modules
itself:
- SPD Byte 4 - only 4Gb density instead of 8Gb for mc_ehl1
- SPD Byte 5 - different Row and Column Address Bits
- SPD Byte 29/30 - 4Gb LPDDR4 needs 130ns tRFCab
- SPD Byte 31/32 - 4Gb LPDDR4 needs 60ns tRFCpb
Change-Id: Icb25f418952f0c96117140863d0d9c897d814ac5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Return the package with a value for the dptf user space service.
This is required in write tpch method for pch device under dptf
driver.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I64e1bb04a6115c7f93c84a5d6644101ac1d3d8ba
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Karthikeyan Ramasubramanian