Until ME boots (which takes seconds on X201) the reported temperature
is 128 °C which triggers Linux overheat alarm which shuts down.
Pretend temperature is 40°C until ME boots.
Change-Id: Ia49fa03c6eb27f539a23711f2c8ebfde72b1dc18
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3404
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On X201 to enable EHCI debug you need to go through EC if USB power is
disabled so we need to inclue ec.c.
Change-Id: I8f8b7de639ecaebceaa53cd338136befaeec8214
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3405
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Enable UMTS on Lenovo X60 and X201.
Enable radios if no options are available.
Enable dock on Lenovo X201.
Based on my X201 branch.
Change-Id: I6e8d3bbd6a6b1a8e59473dd5cc8125a1583d75df
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a struct for referencing UART registers. The layout is quite
strange on this chip, as the entire register space can take on three
different meanings depending on the line control settings (in the LCR
register) And to make things more confusing, some offsets reference
different registers depending on if a read or a write operation is
used.
Change-Id: Ie62af9c0e0edafd01b81686a0fe5c5c1d4fa06c4
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This ancient board with Intel e7505 invalidates cache while it does HW
scrubbing for ECC in romstage. This breaks usbdebug console and prevents
system from booting.
If both EARLY_CONSOLE and USBDEBUG are selected, skip ECC scrubbing under
these rare conditions to boot system.
Change-Id: I6cb43bf69af54119f4a582dcaf498dd941d4c62d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3385
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In case with EARLY_CONSOLE, this printk is called before any other
console is configured to transmit data. This outputs garbage on
CONSOLE_SERIAL as baudrate is not yet programmed.
For case without EARLY_CONSOLE, the order in which different console
drivers initialize is obscure. Might sometimes work properly.
Change-Id: I3792161e0a6dc17e17262048cc9136044dd69dc5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3384
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Add comment how one can debug the usbdebug hardware init.
Do not send printk's to usbdebug console when one is debugging
the usbdebug console initialisation itself.
Change-Id: I21a285cb31cf64e853bc626f8b6a617bc5a8be19
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3382
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Setting IRQ delivery to FSB got lost in the rebase process
for commit e6143531.
I captured following error on dmesg and this patch fixes it for
i82801dx.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 2) ...
....... failed.
...trying to set up timer as Virtual Wire IRQ...
..... works.
Change-Id: I0768976cc6b0deab213ad9bd4771e0f278de634c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3371
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This is spkmodem receiver counterpart.
Change-Id: Id27d32608502029fb6fcc8154f508811bf5ca77b
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3411
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Mapping is as follows: bit 15 corresponds to GPIO15 ... bit 0 corresponds to
GPIO0.
Change-Id: I661ce56d9373887270ba3c0518892fbbe6d9de7c
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3436
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently in Intel BD82x6x southbridge’s `Makefile.inc` the
file `usb_debug.c` is added twice to the build.
This was introduced in
commit 4063ede3fb
Author: Ronald G. Minnich <rminnich@google.com>
Date: Mon Feb 4 20:31:51 2013 -0800
bd82x6x: Fix compiling with USB debug port support
Reviewed-on: http://review.coreboot.org/2784
but was unneeded because it had been already added in
the following commit.
commit 4141993536
Author: Sven Schnelle <svens@stackframe.org>
Date: Sat Jul 28 08:52:44 2012 +0200
bd82x6x: Fix CONFIG_USBDEBUG
Reviewed-on: http://review.coreboot.org/1376
Therefore basically revert that hunk.
There is no policy on how to order these additions, so leave
it to a possible separate commit, unifying this.
Kyösti Mälkki suspects that these additions were meant for
the Intel Lynx Point [1].
[1] http://review.coreboot.org/#/c/3424/
Change-Id: Iaa8de6fcc0d6f3a0a92a28fcb603d7777aa8b24c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3425
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix obvious mistake in cycle that displays GPI status
I hope i found all duplicates of it.
Change-Id: Ic21ff3ecab85953463e5c23daf808dd5edc82ff8
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3435
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current method will treat hex values as 0 and would calculate the wrong
size. This change switches back to an earlier method which used shell syntax
to add the offset and size.
Change-Id: I9fb2d9b323f113cc56a5ad2e38b47d2d22084f08
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3432
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is loosely based on Christoph Grenz' ACPI code for the W83627HF
and makes use of the PnP super i/o ACPI framework.
Change-Id: I5e1cd09b83c0041f440562d2a1b73e4560589cb7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3288
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I'm trying to make writing ACPI code for super i/o devices more
comfortable.
pnp.asl hosts some general cpp macros.
The other four files are to be included in dsdt trees. They are
controlled by cpp macros which should be defined/undefined before
inclusion.
Work was inspired by Christoph Grenz' ACPI code for the W83627HF.
Change-Id: Idb55332ba9bc788c98964d30a450e0d734cf28ec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3286
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The bootblock and ROM stages are the only ones that are really required to be
loaded in the quite limited on chip RAM during startup. Rather than load the
whole image which requires everything to be small, load just the bootblock and
the ROM stage, allowing the rest of the image to be arbitrarily large. Loading
a minimal amount of stuff should also improve boot performance a little bit.
Change-Id: I2fede63b8d3d8f0d880e4a692ae423021f8232b6
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3421
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that the ROM size is decoupled from the size of the on chip RAM,
it's size is now only constrained by the size of the medium it's loaded
from and the memory it's being loaded into, probably GBs in both cases.
Making it 4MB is a reasonable compromise between giving the payload lots
of breathing room and wasting space on the source medium which won't be
used.
Change-Id: I80932e0d4ce2dad02c3879345382e7d6ba44503a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3422
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Until we get serial working, this is a good way to show that coreboot is
running. It can be removed once we have better methods.
Change-Id: I62d25e52aa88a97aba4c959538d680b67a0bbbb2
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
EPIA-M850 can now boot linux. For a list of issues, see:
http://www.coreboot.org/VIA_EPIA-M850
That's all folks.
Change-Id: I7624944dbc05fbf3019897a116954d71dfda0031
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/1228
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the minimal code needed to get past ramstage, load SeaBIOS, jump
to GRUB2, and boot linux (or load memtest). See individual source files for
the status of each individual component.
Change-Id: Ib7d5d7593c945f18af2c2fc5e0ae689ba66131a2
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3419
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The VX900 can be connected to either DDR2 or DDR3. On my board, it is
DDR3, hence why there is no and will be no DDR2 code from my side.
This is the raminit for DDR3 dimms for the VX900. I like the term
"raminit" better than "memory training". This is a device, not a dog.
What works and what doesn't is documented in the code. It does not
make sense to hide that information in a commit message.
Change-Id: Ib2ebc10e6d4d22d0a937fe9e895c17ce79153c88
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3417
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In some cases, we want a ram_check that does not die and does not
clobber the terminal with useless output that slows us down a lot.
Usage examples include Checking if the RAM is up at the start of
raminit, or checking if each rank is accessible as it is being
initialized.
As with all other ram_checks, this is more of a "Is my DRAM properly
configured?" test, which is exactly what we want for something to use
during memory initialization.
Change-Id: I95d8d9a2ce1e29c74ef97b90aba0773f88ae832c
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3416
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support for VX900 early initialization up until, but not including
raminit. Add the basic infrastructure, add a romstrap table, and
functionality to configure the CPU bus and SMBus.
This code is necessary and sufficient to prepare us for raminit.
Change-Id: Icc9c41e4927b589f17416836f87a6a5843b24aa7
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3372
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a common implementation of SMBus functionality for early chipsets. Note
however, that existing via chipsets are not ported to this code. Porting
will require hardware testing to make sure everything is fine.
This code is used in the VIA VX900 branch.
Change-Id: If5ad8cd0942ac02d358a0139967e7d85d395660f
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/144
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Loading on an OMAP SOC requires that the first sector of the image have a
configuration header, and, when not an execute in place image, an additional
header which describes how big the image is and where it should be loaded.
This change adds some infrastructure to statically build that header using C
code, and to paste the header onto the front of coreboot.rom in a new top
level target file called MLO.
The configuration header we're using is as inert as possible, in line with
what U-Boot is doing. I think it could be used to give additional
configuration parameters to the built-in ROM on the SOC, but we don't need to
do that, and there didn't seem to be any actual documentation how to do that.
Because the header is built from C and is defined per CPU, it would be
possible to include extra settings in other CPUs if desired.
Adding a new top level build target is a bit disruptive, but should be
contained to the am335x directory and not interfere with other mainboards.
Change-Id: I06d346a4050c20963b3c7c6e8a152070bf2d145a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3332
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On ARM, there's frequently some firmware built into the SOC which runs
first and which loads other firmware like Coreboot from some other
media. To prevent the bootblock from having to know how to find and load
the ROM stage from what may be a complicated source (sd card,
netbooting, etc.), we can put the ROM stage immediately after the
bootblock and ensure that they're both loaded at the same time.
This change adjusts the Makefile.inc for ARM so that the ROM stage is put
into the image before any other files so that we know it comes first.
This changes the behavior of the CONFIG_UPDATE_IMAGE config option used
by abuild, although it's not entirely clear whether that's still used.
Change-Id: I832386243788156db5f5abbc9760a4e2026cf2cd
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3420
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Keep in mind that we can _NOT_ read back the current state
of the LEDS as some crazy FPGA designer wanted it that way.
Change-Id: I5cd1ac598072318b3234d1ec35a79271655b46ac
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3271
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
fam15 vendorcode (src/vendorcode/amd/agesa/f15tn) was licensed under the
AMD software license agreement. Change this license to 3-clause BSD.
Change-Id: I7cab09bb58ef7cd24602628e2278672d577214a2
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3414
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
While some of the case .. break statement actually weren't needed,
too are, since otherwise the option parsing loop hangs.
Exit conditions for that endless loop: "--" or no more arguments,
in line with GNU command line parsing rules.
Change-Id: I0dbc35e530fb8c93a0f7de05ac47f325555ad4a4
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3418
Tested-by: build bot (Jenkins)
Reviewed-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
If EARLY_CONSOLE is not selected, the PCI function for EHCI
host controller must be configured in ramstage instead.
Change-Id: I20f7569f79484c744bc413450bfa139052f3580f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3383
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Without that commit, with CONFIG_PCI_OPTION_ROM_RUN_YABEL,
The VGA option rom doesn't init the right display:
it initializes the external display, where we have
a black scren(with backlight on).
This commit is based on the code of mainboard.c in
src/mainboard/roda/rk886ex.
Change-Id: I8457aaf0503e0efdf0fcba9ff5e8a07ac04c5ca6
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3265
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
First copy over from SeaBIOS git repo, then adapt for coreboot:
Disable cpu/pci hotplug bits. Disable dynamic pci window.
Both depend on stuff in the SSDT tables created by SeaBIOS.
Bits are left in, but deactivated via #if 0, so it's easier
to see the differences when diffing the coreboot tables with
the SeaBIOS tables.
Adapt dsdt DefinitionBlock.
Enable acpi table generation in acpi_tables.c.
With this patch linux boots successfully with ACPI enabled.
It's not bug-free though. Missing cpu detection leads to
funky messages like this one:
weird, boot CPU (#0) not listed by the BIOS.
and SMP most likely wouldn't work either.
Change-Id: Ic3803a6f1ef6d54c11cc4ca3844d3032a374ae6b
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3342
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Port most of the functions found in ec/acpi/ec.c to ACPI Source Language
(ASL). These functions are used to control embedded controllers with the
standard ACPI interface (mostly through i/o ports 0x62 / 0x66).
The following methods are implemented and tested against the power
managements channels of a ITE IT8516E embedded controller:
* WAIT_EC_SC Wait for a bit in the EC_SC register
* SEND_EC_COMMAND Send one command byte to the EC_SC register
* SEND_EC_DATA Send one data byte to the EC_DATA register
* RECV_EC_DATA Read one byte of data from the EC_DATA register
* EC_READ Read one byte from ec memory (through cmd 0x80)
* EC_WRITE Write one byte to ec memory (through cmd 0x81)
To use the provided methods, one should include `ec/acpi/ec.asl` in the
EC device code. Prior doing so, two macros should be defined to identify
the used i/o ports:
* EC_SC_IO I/o address of the EC_SC register
* EC_DATA_IO I/o address of the EC_DATA register
Change-Id: I8c6706075fb4980329c228e5b830d5f4e9b188dd
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3285
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Added support for Intel Atom cpu to msrtool
Fixed a cut&paste error in nehalem msr bits definition
It has been tested with a N455 cpu and msrtool output can be review at:
http://www.trillion01.com/coreboot/msrtool_atom.txt
Change-Id: I0ecf455b559185e2d16fa1a655bf021efc2ef537
Signed-off-by: Olivier Langlois <olivier@olivierlanglois.net>
Reviewed-on: http://review.coreboot.org/3351
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The DDI connector table and the PCIe Port List lookup table are
copied onto HEAP. This copy is not needed since these are lookup
tables used to define the platform configuration.
Change-Id: If4760f80e08faa8da4fd11337a3812f89cf805f9
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3394
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add CONST modifiers to read-only pass-by-reference function
parameters in AGESA. This allows the use of "const" modifiers
on the declaration of lookup tables that are pass-by-reference.
These will be used to identify tables that are copied onto the
HEAP but don't need to be.
Change-Id: Ie1187a427804fddf47b935a110ad23931a3447a9
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3393
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add boot cpu to the device tree. Figure the number of CPUs installed
(using the qemu firmware config interface) and add cpu devices for them,
so they show up in all generated BIOS tables correctly. This gets SMP
going.
Change-Id: I0e99f98942d8ca90150b27fc13c1c7e926a1a644
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3345
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch adds a qemu x86 cpu chip. It has no initialization function
as this isn't needed on virtual hardware. A virtual machine can have
pretty much any CPU: qemu emulates a wide range of x86 CPUs (try 'qemu
-cpu ? for a list), also with 'qemu -cpu host' the guest will see a cpu
which is (almost) identical to the one on the host machine. So I've
added X86_VENDOR_ANY as wildcard match for the cpu_table.
Change-Id: Ib01210694b09702e41ed806f31d0033e840a863f
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3344
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This driver communicates with the IT8516e on the Kontron KTQM77.
Since we don't know if the firmware and protocol are standard for
the chip or customized to the board, call it kontron/it8516e.
Change-Id: I7382172c6d865d60106c929124444821a07a5184
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3390
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ica3afbf8277cb025251da7af181f8de0d0036b45
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3389
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When I've first written this macro in 2011, the correct define for
verbose SMBus message was CONFIG_DEBUG_SMBUS_SETUP. This has since
been changed to CONFIG_DEBUG_SMBUS. I didn't catch that, and this made
the printsmbus macro always evaluate to an empty statement.
Use the proper CONFIG_DEBUG_SMBUS define. This makes printsmbus
functional again.
Change-Id: Iaf03354b179cc4a061e0b65f5b746af10f5d2b88
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3379
Tested-by: build bot (Jenkins)
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Needed to make 'register "gpo" = ...' work.
While being at it add comments saying which device is which.
Change-Id: I911d5e4a7b6c7abf4ad73e863ab201e9e55ee0d4
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3346
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Kyösti Mälkki