When GDB support is compiled in, halt() in libpayload will call
gdb_enter(). halt() is defined in <stdlib.h> and gdb_enter() in
<libpayload.h>. Usually files just include <libpayload.h> so this is not
a problem, but in some situatons a payload may just include <stdlib.h>
(or a file including it like <assert.h>), leading to an undeclared
identifier here. Move the GDB functions to <stdlib.h> to solve this.
Change-Id: I7b23b8ac9cd302aa6ef96f24565130490ac40071
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25730
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The VA space needs to be extended to support 48bit, as on Cavium SoCs
the MMIO starts at 1 << 47.
The following changes were done to coreboot and libpayload:
* Use page table lvl 0
* Increase VA bits to 48
* Enable 256TB in MMU controller
* Add additional asserts
Tested on Cavium SoC and two ARM64 Chromebooks.
Change-Id: I89e6a4809b6b725c3945bad7fce82b0dfee7c262
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/24970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add just enough code and boilerplate to keep it compatible with future
libflashrom.
Change-Id: If0d46fab141da525f8f115d3f6045a8c417569eb
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch adds support to read the SKU ID entry from the coreboot table
that was recently added in coreboot.
Change-Id: I1c3b375da6119a4f8e8e7e25a11644becb90f927
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22743
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch mirrors recent cleanups in coreboot regarding the strapping
ID entries in the coreboot table.
Change-Id: Ia5c3728daf2cb317f8e2bc72c6f1714d6cb4d080
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
bebitenc() just runs a downward loop over the same body as lebitenc().
That doesn't give you a byte-swapped result, it gives you the same final
value, just starting from the other side to fill it in. (Also, it
confused i++ and i--, so it really gives you a compiler error.)
The correct code needs to have the array index inverted relative to the
bit shift index to produce a big endian result.
Change-Id: I5c2da3a196334844ce23468bd0124bbe2f378c46
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When building the Go version of cbmem I found that
LB_TAG_MAC_ADDRS has the same value as LB_TAG_VERSION_TIMESTAMP.
I am guessing that this tag was little used. In any event, move it
forward to 0x33.
Change-Id: I038ad68e787e56903a2ed9cb530809a55821c313
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/22218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
this adds convenience definitions for MSECS_PER_SEC, USECS_PER_MSEC,
and USECS_PER_SEC along the lines of the time units in coreboot's
<timer.h>.
Change-Id: I489dc2d1ff55d137936acec74ac875dc7fbc1713
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/20882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
the __must_check function attribute is pretty much straight from the
linux kernel - used to encourage callers to consume function return
values.
Change-Id: I1812d957b745d6bebe2a8d34a9c4862316aa8530
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/20881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of storing inverted-colored bitmaps,
invert drawing of text bitmap on the fly by adding
an invert parameter down to libpayload. Merging
pivot and invert fields into flags field.
BUG=b:35585623
BRANCH=None
TEST=Make sure compiles successfully
CQ-DEPEND=CL:506453
Change-Id: Ide6893a26f19eb2490377d4d53366ad145a9e6e3
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some simple implementation of the MultiBoot protocol may not pass a
memory map (MULTIBOOT_FLAGS_MMAP missing in the flags) but just the two
values for low and high memory, indicated by the MULTIBOOT_FLAGS_MEMINFO
flag.
Support those kind of boot loaders too, instead of falling back to the
hard-coded values in lib_get_sysinfo().
Tested with a multiboot enhanced version of FILO.
Change-Id: I22cf9e3ec0075aff040390bd177c5cd22d439b81
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18350
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
BUG=chrome-os-partner:56947
TEST=Verifed country code can be parsed from VPD in depthcharge.
BRANCH=None
Change-Id: I2fbbd4a784c50538331747e1ef78c33c6b8a679b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: acea6e2a200e8bd78fd458255ac7fad307406989
Original-Change-Id: I4616fefc6a377d7830397cdadb493927358e25cc
Original-Signed-off-by: Kan Yan <kyan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/425819
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18124
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
MAX_ARGC_COUNT limits the payload to ten parameters which is not
enough when used with a proprietary first stage bootloader providing
hardware description using around 20 parameters.
This patch makes the libpayload able to get up to 32 parameters.
Change-Id: I49925040d951dffb9c11425334674d8d498821f2
Signed-off-by: Jeremy Compostella <jeremy.compostella@gmail.com>
Reviewed-on: https://review.coreboot.org/17467
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch adds functionality to compile a C data structure into a raw
binary file, add it to CBFS and allow coreboot to load it at runtime.
This is useful in all cases where we need to be able to have several
larger data sets available in an image, but will only require a small
subset of them at boot (a classic example would be DRAM parameters) or
only require it in certain boot modes. This allows us to load less data
from flash and increase boot speed compared to solutions that compile
all data sets into a stage.
Each structure has to be defined in a separate .c file which contains no
functions and only a single global variable. The data type must be
serialization safe (composed of only fixed-width types, paying attention
to padding). It must be added to CBFS in a Makefile with the 'struct'
file processor.
Change-Id: Iab65c0b6ebea235089f741eaa8098743e54d6ccc
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16272
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The libpayload CBFS APIs are pretty old and clunky, primarily because of
the way the cbfs_media struct may or may not be passed in and may be
initialized inside the API calls in a way that cannot be passed back out
again. Due to this, the only real CBFS access function we have always
reads a whole file with all metadata, and everything else has to build
on top of that. This makes certain tasks like reading just a file
attribute very inefficient on non-memory-mapped platforms (because you
always have to map the whole file).
This patch isn't going to fix the world, but will allow a bit more
flexibility by bolting a new API on top which uses a struct cbfs_handle
to represent a found but not yet read file. A cbfs_handle contains a
copy of the cbfs_media needed to read the file, so it can be kept and
passed around to read individual parts of it after the initial lookup.
The existing (non-media) legacy API is retained for backwards
compatibility, as is cbfs_file_get_contents() (which is most likely what
more recent payloads would have used, and also a good convenience
wrapper for the most simple use case), but they are now implemented on
top of the new API.
TEST=Booted Oak, made sure that firmware screens and software sync
worked okay.
Change-Id: I269f3979e77ae691ee9d4e1ab564eff6d45b7cbe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/14810
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Extend the serial port description to include the input clock frequency
and a payload specific value.
Without the input frequency it is impossible for the payload to compute
the baud-rate divisor without making an assumption about the frequency.
This breaks down when the UART is able to support multiple input clock
frequencies.
Add the UART_PCI_ADDR Kconfig value to specify the unique PCI device
being used as the console UART. Specify this value as zero when the
UART is not on the PCI bus. Otherwise specify the device using bus,
device and function along with setting the valid bit.
Currently the only payload to consume these new fields is the EDK-II
CorebootPayloadPkg.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file:
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Build EDK2 CorebootPayloadPkg/CorebootPayloadPkgIa32.dsc to generate
UEFIPAYLOAD.fd
* Testing is successful when CorebootPayloadPkg is able to properly
initialize the serial port without using built-in values.
Change-Id: Id4b4455bbf9583f0d66c315d38c493a81fd852a8
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14609
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
BUG=chrome-os-partner:49249
TEST=Compiles and boots and detect USB storage
BRANCH=none
Change-Id: I9007399e1f785e6f1d2258225e3f7cc602053aed
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1db43f53973d2124e41186777caa829aa346ace3
Original-Change-Id: I943d19a3a7d785bd075073b57ba6388662d7df90
Original-Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/333311
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14659
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Move time functions and prototypes from libpayload.h to time.h.
In a similar manner to other c libary headers, this change makes
porting existing applications to libpayload easier.
Change-Id: I71e27c6dddde6e77e0e9b4d7be7cd5298e03a648
Signed-off-by: Stef van Os <stef.van.os@prodrive-technologies.com>
Reviewed-on: https://review.coreboot.org/14437
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is adding complexity to the code more than it saves
space, plus some of the tables could potentially be interesting
outside of the ChromeOS context.
Change-Id: I4bf24608f3e26d3b7871a5031ae8f03bc2c8c21f
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14070
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This patch ports the LZ4 decompression code that debuted in libpayload
last year to coreboot for use in CBFS stages (upgrading the base
algorithm to LZ4's dev branch to access the new in-place decompression
checks). This is especially useful for pre-RAM stages in constrained
SRAM-based systems, which previously could not be compressed due to
the size requirements of the LZMA scratchpad and bounce buffer. The
LZ4 algorithm offers a very lean decompressor function and in-place
decompression support to achieve roughly the same boot speed gains
(trading compression ratio for decompression time) with nearly no
memory overhead.
For now we only activate it for the stages that had previously not been
compressed at all on non-XIP (read: non-x86) boards. In the future we
may also consider replacing LZMA completely for certain boards, since
which algorithm wins out on boot speed depends on board-specific
parameters (architecture, processor speed, SPI transfer rate, etc.).
BRANCH=None
BUG=None
TEST=Built and booted Oak, Jerry, Nyan and Falco. Measured boot time on
Oak to be about ~20ms faster (cutting load times for affected stages
almost in half).
Change-Id: Iec256c0e6d585d1b69985461939884a54e3ab900
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/13638
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When CONFIG_LP_TIMER_RDTSC is enabled honor the TSC information
exported in the coreboot tables as the cpu_khz frequency. That
allows get_cpu_speed() not to be called which currently relies
on the 8254 PIT. As certain x86 platforms allow that device
to be optional or turned off for power saving reasons, allow
a path where get_cpu_speed() is no longer called. Additionally,
this approach also allows the libpayload to not duplicate logic
that already exists in coreboot.
BUG=chrome-os-partner:50214
BRANCH=glados
TEST=Confirmed in payload TSC frequency is honored instead of
using get_cpu_speed().
Change-Id: Ib8993afdfb49065d43de705d6dbbdb9174b6f2c4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13671
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
archive.h is a header file for the programs which need to parse an archive
created by 'archive' tool. See archive.h for the format description.
BUG=chromium:502066
BRANCH=tot
TEST=Tested on Glados
Change-Id: I2bee9d7c12b0e1bce1529dfef360c5fa4ce0872d
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/311201
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://review.coreboot.org/12734
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
get_image_dimension returns the width or height of the image projected on
canvas.
This is necessary for example when two images of different lengths have to
be placed side by side in the center of the canvas and the widths of the
images must be adjusted according to the height.
BUG=chromium:502066
BRANCH=tot
TEST=Tested on Samus
Change-Id: I119c83891f48046e888b6b526e63348e74f8b77c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: d1a97f0492eb02f906feb5b879b7b43518dfa4d7
Original-Change-Id: Ie13f7994d639ea1556f73690b6b6b413ae64223c
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/304113
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11929
Tested-by: build bot (Jenkins)
This change makes the code in graphics.c more descriptive and readable.
Especially, it makes expressions for scale calculation look what they
are meant to do. It also includes:
- Rename variables (struct fraction, dim_org, etc.) for more consistency
- Add more input validation (div-by-zero, etc.)
BUG=chromium:502066
BRANCH=master
TEST=Tested on Samus
CQ-DEPEND=CL:304860
Change-Id: I2694912bb7b6017d5655de2fd655b95432addb22
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: 0863dc3ee925d3a05c83c66397b19a57f5478ef3
Original-Change-Id: Id8e349b8e09082fb84c3e1a984617f916e16c518
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/304861
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11928
Tested-by: build bot (Jenkins)
This change adds 'pivot' option to draw_bitmap. It controls the point of the
image based on which the image is positioned. For example, if a pivot is set
to the center of the image horizontally and vertically, the image is
positioned using pos_rel as the center of the image.
This feature is necessary, for example, to place a text image in the center
of the screen because each image has a different width depending on the
language.
This change also makes draw_bitmap accept both horizontal and vertical size.
If either of them is zero, the other non-zero value is used to derive the
size to keep the aspect ratio.
Specifying the height is necessary to keep font sizes the same when drawing
text images of different lengths.
draw_bitmap_direct is a variant of draw_bitmap and it draws an image using
a native coordinate and the original size (as opposed to the location and
the size relative to the canvas).
CL:303074 has real use cases.
BUG=none
BRANCH=tot
TEST=Tested on Samus
Change-Id: I5fde69fcb5cc9dc53e827dd9fcf001a0a32748d4
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: 82a0a8b60808410652552ed3a888937724111584
Original-Change-Id: I0b0d9113ebecf14e8c70de7a3562b215f69f2d4c
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/302855
Reviewed-on: http://review.coreboot.org/11927
Tested-by: build bot (Jenkins)
This change adds load_bitmap API, which loads a bitmap file from cbfs
and returns a pointer to the image data.
BUG=none
BRANCH=tot
TEST=Tested on Samus
Change-Id: I7d7874f6f68c414dc877a012ad96c393e42dc35e
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: 9d33e713a0cf6bd1365418dad989e47e86db01e4
Original-Change-Id: Idbf9682c2fa9df3f0bd296ca47edd02cd09cfd01
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/302194
Original-Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: http://review.coreboot.org/11925
Tested-by: build bot (Jenkins)
This change allows draw_bitmap to draw an image outside the canvas
with the original size if the scale parameter is zero. This is used
for example when drawing a splash screen which has to be positioned
at a pixel perfect location.
BUG=none
BRANCH=master
TEST=Draw pictures and boxes on Samus and Ryu
Change-Id: Ia2d8799184d1aa192e2c50850e248bee8f234006
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: 45d4717fe5c3e3554bd79b63ade490d88cf00bbe
Original-Change-Id: I48aa21122cfc2ee43bcb1b8f87b00c66abdc230e
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/295961
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11923
Tested-by: build bot (Jenkins)
draw_bitmap renders a bitmap image on screen with position and sizes
scaled relative to the screen. images are scaled up or down by nearest
neighbor interpolation.
BUG=chrome-os-partner:43444
BRANCH=tot
TEST=drew bitmap images on Samus
Change-Id: Ib599acc85b25626a6aed1fa9884ecd8e169bb860
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c910c9cdb7efc53aace067bd081aeefc07556811
Original-Reviewed-on: https://chromium-review.googlesource.com/290302
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Change-Id: Ib599acc85b25626a6aed1fa9884ecd8e169bb860
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/295532
Reviewed-on: http://review.coreboot.org/11584
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This change introduces cbgfx, a graphics library, which provides APIs for
drawing basic shapes, texts, graphic data, etc. on a screen.
BUG=chrome-os-partner:43444
BRANCH=tot
TEST=Drew boxes by draw command of depthcharge cli on Samus
Change-Id: I6019e5998e65dca3ab4785a90669b5db02463d2e
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Original-Commit-Id: 5b3ebce8eae91be742e4f977d3407d24e1537580
Original-Reviewed-on: https://chromium-review.googlesource.com/290301
Original-Reviewed-by: Stefan Reinauer <reinauer@google.com>
Original-Change-Id: I10db27715cb907bdc451a33ed99d257e3af241b7
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/291065
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11408
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Taken from cbfstool.
Change-Id: I4387900517dbfb1aa51ae6f679e26d0cf5b2acf8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/11808
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Set XN bit of block upper attribute to device memory in mmu. CPU may
speculatively prefetch instructions from device memory, but the IO
subsystem of some implementation may not support this operation. Set
this attribute to device memory mmu entries can prevent CPU from
prefetching device memory.
BRANCH=none
BUG=none
TEST=build and booted to kernel on oak-rev3 with dcm enabled.
Change-Id: I52ac7d7c84220624aaf6a48d64b9110d7afeb293
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7b01a4157cb046a5e75ea7625060a602e7a63c3c
Original-Change-Id: Id535e990a23b6c89123b5a4e64d7ed21eebed607
Original-Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/302301
Original-Commit-Ready: Yidi Lin <yidi.lin@mediatek.com>
Original-Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/11722
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
cbfs_file_find_attr(file, tag) finds the first attribute of file with
the given tag.
Change-Id: I78ee3b996b4b086605244c5d7d57ef7e3fc1db47
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11678
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Decompression is handled transparently within cbfs_get_file_content:
const char *name = "foo.bmp";
void *dst = cbfs_get_file_content(media, name, type, NULL);
To keep things consistent, a couple of API changes were necessary:
- cbfs_get_file_content always returns a copy of the data, even for
uncompressed files. It's the callers responsibility to free the
memory.
- same for cbfs_load_payload and cbfs_find_file.
- cbfs_load_optionrom doesn't take a "dest" argument anymore but always
returns a copy of the data, for compressed and uncompressed files.
Like with cbfs_get_file_content, the caller is responsible to free it.
It also decompresses based on extended file attributes instead of the
cbfs_optionrom subheader that libpayload specified but that (AFAIK)
nobody ever used, given that there's not even tooling for that.
Change-Id: If959e3dff9b93c6ae45ec7358afcc7840bc17218
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10938
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This comes from cbfstool (GPL) into libpayload (BSD-l), but I could have
just as well written it in libpayload first.
Change-Id: I86baefe5c299125a4733fa20523efd5d06de7182
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11675
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Revive ffs() in a more fancy way (that is more likely to be accepted).
We dropped it in
7a8a4ab lib: Unify log2() and related functions
but there is at least one user: flashrom.
Change-Id: I4e3fc15816b778e640bceea0d89cd9624d271c2e
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/11591
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change allows video_printf to left/center/right-align text depending on
the enum value provided by the caller. This is useful especially because usually
the length of formatted string is unknown before calling video_printf.
BUG=none
BRANCH=smaug
TEST=drew fastboot screens on Smaug
CQ-DEPEND=CL:296460
Reviewed-on: https://chromium-review.googlesource.com/292929
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 436f05f60c1b88626740a35913e3ad37b5c777a3)
Change-Id: If1d50b7d8ddaa86eddc1618946756184cb87bfe1
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/295413
Reviewed-on: http://review.coreboot.org/11583
Tested-by: build bot (Jenkins)
Julius Werner