SMBHST_STAT_NOERROR was a redefinition of SMBHST_STAT_INTERRUPT that was
used in smbus_wait_until_done. Remove the misleading bit definition that
also didn't correspond with the register definitions and replace it with
the definition of the actual bit that gets checked. Also add a comment
that the code actually checks the IRQ status flag to see if the last
command is already completed.
Change-Id: I1a58fe0d58d3887dd2e83320e977a57e271685b3
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The patch also rewrites the bit definition using shifts to make them
easier to read.
The older non-SoC chips can probably also use the new header file, but
for this patch the scope is limited to soc/amd, since the older non-SoC
chips don't use the SMBUS controller code in soc/amd/common.
TEST=Timeless build for amd/mandolin and amd/gardenia doesn't change.
Change-Id: Ifd5e7e64a41f1cb20cdc4d6ad1e675d7f2de352b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The code on Stoneyridge didn't set the FCH_AOAC_TARGET_DEVICE_STATE bits
to FCH_AOAC_D0_INITIALIZED like the code for Picasso does, but that is
the default value after reset for those bits on both platforms.
Change-Id: I7cae23257ae54da73b713fe88aca5edfa4656754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The register locations and bit definitions are the same for Stoneyridge
and Picasso. Since not all devices are present on all SoCs, keep those
numbers in the SoC-specific code.
Change-Id: Ib882927e399031c376738e5a35793b3d7654b9cf
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The ability to set up a custom memory profile is useful if you don't
like the XMP memory profiles (if they exist) of your RAM sticks, or
want to try some overclocking. Read SPD data will be overriden by your
custom values. Tested on Crucial BLT8G3D1869DT1TX0 (1866MHz 9-9-9-27).
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I1238ff00ef0efd11ea807794827476c30ac98065
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Add XMP memory profiles support that has been tested on f15tn (A88XM-E)
and f16kb (AM1I-A) with two Crucial BLT8G3D1869DT1TX0, XMP 1 profile.
Added using the datasheets from https://github.com/mikebdp2/ddr3spd :
JEDEC_DDR3_SPD_4_01_02_11R24.pdf and Intel_XMP_Spec_Rev1.1.pdf
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I584416e3376afdf377a11783e55c5e9ff41e6b0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40488
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On x86_64 the cannary is 8 bytes in size, so write the additional
4 bytes to make SMM handler happy.
Tested on Intel Skylake in long mode. No longer dies in SMM.
Change-Id: Id805c65717ec22f413803c21928d070602522b2c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48215
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The previous code was crashing when jumping back to ramstage, now it
works. The GDT is now using the same values as the other ones in
coreboot.
Change-Id: Id00467d9d8a4138ddea73adbda4b39f12def583f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48214
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the fw_config entries for the newly added boot device fields.
These are added as separate fields since a board may have more
than one selected.
BUG=b:173129299
TEST=abuild google/volteer
Change-Id: I2af9ffcf0b90d4f4b7f2f31613ee110d8f350454
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The initial commit only focused on GL9755S and RTS5261, but there
were recently other cards added to the fw_config and those also
need to be added to the probe lists.
BUG=b:173207454
TEST=abuild google/volteer
Change-Id: Ic27074a016ffbd4c4dd86104a6d85437357c4b82
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Now that the initial version of the Picasso FSP binaries have finally
landed, we can set the default paths to point to them now.
Change-Id: Ib2241cc90c7113e0c3de4409e08b9ae1f4c2f51e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42472
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the newest SMU firmware and FSP blobs for the picasso project.
This supports Picasso, Dali, and Pollock devices.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I75e6f3d2a59ed8b2e42afba3a6978574373ec4e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The FSP-M/S/T related headers added are generated as per FSP v2341.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I98f738402490b47efa1a346f81db47857e384e13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Update Kconfig:
1. use FSP2.1 instead of 2.2
2. remove HECI_DISABLE_USING_SMM config
3. update CAR related stack & ram size
4. update FSP heap size
5. set IED region size = 0 as it is not used
6. update SMM TSEG size
7. update RP & I2C max device #s
8. update UART base address
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I6a44d357d71be706f402a6b2a4f2d4e7c0eeb4a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45078
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The extracted VBIOS Option ROM ships the same ID for several
generations, not matching the ID on the hardware resulting in a
mismatch, and coreboot does not run the Option ROM.
PCI ROM image, vendor ID 8086, device ID 0406,
ID mismatch: vendor ID 8086, device ID 5916
Add the appropriate mappings.
TEST=coreboot runs the ROM on the TUXEDO Book BU1406.
Change-Id: Ia167d91627a7ff1b329ea75f150b3ce95c0acccb
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43853
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Default VBT supports only integrated Display port. Drawman supports a
HDMI port and hence support a separate VBT for Drawman.
BUG=b:161190931
BRANCH=dedede
TEST=Build and boot to OS in Drawlat and Drawman.
Cq-Depend: TBD
Change-Id: I8895cc67d87428eddb31328f1e3a90c346b54533
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Add daughter-board ports bit field and mask in devicetree.
BUG=b:161190931
BRANCH=dedede
TEST=Build and boot to OS in drawlat & drawman.
Change-Id: Ibbd86fc8c3e44a7d1703b8ce75c48881226545c9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Config HID-I2C device to level trigger.
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:171546871
TEST=emerge-dedede coreboot
Change-Id: If8be25f591715765a99920b79482c862b1cc7079
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Check that stages running in CAR have their start and end in CAR.
Change-Id: I292aacce564c23d9ae21aa46c5e2f8784fa6a609
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Older GCCs don't support _Static_assert without a message string as the
second argument. AFAICT _Static_assert with two arguments is in C11 but
omitting the message argument is an extension.
The tests appear to be built with the system gcc rather than our
crossgcc so that's probably why this was not cought by CI.
Change-Id: I41fd0ffc42ded8b6d145c3ec30cc7407a78b9a43
Signed-off-by: Daniel Gröber <dxld@darkboxed.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
In commit 09d50671e6 the AOAC code was
reworked for Picasso and this patch ports this back to Stoneyridge to
facilitate factoring out the functionality into common code.
Change-Id: I836b91dc647987d064170fff7c8ca6ef2ee49211
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The numbers in the array are unsigned, so use an unsigned type there.
Change-Id: I9a85594de0e4c53db965ab84239f19eb46432348
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The power_off_aoac_device function clears the FCH_AOAC_PWR_ON_DEV bit,
so the comment should be that it powers off the devices.
Change-Id: Ia5e5d80b1977c3f53fcd9cf6d48bdb59045dfc3c
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Allows to compile the file under x86_64 without errors.
The caller has to make sure to call the functions while in protected
mode, which is usually the case in early bootblock.
Change-Id: Ic6601e2af57e0acc6474fc3a4297e3d2281decd6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Allows to compile the file under x86_64 without errors.
The caller has to make sure to call the functions while in protected
mode, which is usually the case in early bootblock.
Change-Id: Ic6d98febb357226183c293c11ba7961f27fac40c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Current flash layout doesn't support the fsp debug builds since
the FW_MAIN_A/B doesn't have enough space to hold the fsp debug
binaries along with ME RW binaries.
This patch reduces the SI_ALL size to 3.5MiB and increase the
SI_BIOS to 12.5MiB to include both ME RW and FSP debug binaries.
BRANCH=dedede
TEST=Build and Boot jslrvp with fsp debug enabled coreboot.
Cq-Depend: chrome-internal:3425366
Change-Id: I6f6354b0c80791f626c09dabafe33eefccedb9c2
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
AGESA checks to make sure that the firmware version reading the MRC
cache is the same version that wrote it, so it doesn't need to be
erased during a firmware update.
BUG=b:173724014
TEST=Flash firmware to DUT, update firmware, check RW_MRC_CACHE was
not erased
BRANCH=Zork
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ice3d1d467c25366b7ef678cd6481d043f62644ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Enter long mode on secondary APs.
Tested on Lenovo T410 with additional x86_64 patches.
Tested on HP Z220 with additional x86_64 patches.
Still boots on x86_32.
Change-Id: I53eae082123d1a12cfa97ead1d87d84db4a334c0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Use the system library for header files instead of relative filesystem
paths.
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: I0b356d0188f104d7c49571ce5c8fe65e79589123
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: Id78c478a1252099cd1aa42c62efd406e7e1c5ef8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Update port connector information for Delta Lake.
Tested=Execute "dmidecode -t 8" to check all the information of
SMBIOS type 8 is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I880bb9a5a41077172423f78b56c19aadd93e001f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
As per latest schematics GPP_A15 is not used for EC_SYNC_IRQ
hence remove the unused GPIO.
Wrong GPIO configuration is causing platform reboot issue on
ADLRVP with Chrome SKU.
Change-Id: I704cd722683258c80197d8872d3bdaafb7c923dc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
1. Add 2 ports and 2 endpoints
2. Add support for OVTI5675
WFC Cam is on I2C5 and UFC is on I2C1
BUG=None
BRANCH=None
TEST=Build and Boot adlrvp board and able to capture image
using camera.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I6d2a4fdca99354d1b6977233c70ccd950c99d8a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47497
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure I2C related GPIO as per ADL-P schematics.
This is based on Revision 0.974 of schematics.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I76e1207cb31bed10b6e9fbeb2456b6feec42f97e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Felix Held