49aad6b387
The Serial Peripheral Flash Interface (SPFI) block allows communication with various devices over the SPI bus. It uses a configurable transaction interface and it clocks the bus according to the configured command, address, gap (aka dummy) and data lengths. This controller requires the SPI_ATOMIC_SEQUENCING flag set (write and read done in the same transaction) as it cannot directly control CS and will assert/de-assert CS at the beginning/end of a transaction itself. Note that the size of any transfer cannot be greater than 64KB - 1, as this is configured in a 16-bit field. The SOC has 2 SPFI interfaces each of them providing 5 slave select lines. SPFI 0 supports single and dual modes, SPFI 1 supports single, dual and quad modes. For SPFI interface 0: - The block needs the system PLL and the following top level SPI clock registers to be set: - CR_cr_top_spi0clkinternal_CTRL[2:0] with division value - CR_MIPS_CLOCK_GATE[19]: bit cr_top_SPI0CLKOUT_MIPS set - CR_cr_top_SPI0CLKOUT_CTRL[6:0] with division value - The following MFIO configuration parameters are also required: Signal name Pad name MFIO mode spim0_d0_txd MFIO_MIPS_10 0 spim0_d1_rxd MFIO_MIPS_9 0 spim0_mclk MFIO_MIPS_8 0 spim0_cs0 MFIO_MIPS_2 1 spim0_cs1 MFIO_MIPS_1 1 spim0_cs2 MFIO_MIPS_55 1 MFIO_MIPS_28 1 spim0_cs3 MFIO_MIPS_56 1 MFIO_MIPS_29 1 spim0_cs4 MFIO_MIPS_57 1 MFIO_MIMPS_30 1 For SPFI interface 1: - The block needs the system PLL and the following top level SPI clock registers to be set: - CR_cr_top_spi1clkinternal_CTRL[2:0] with division value - CR_MIPS_CLOCK_GATE[20]: bit cr_top_SPI1CLKOUT_MIPS set - CR_cr_top_SPI1CLKOUT_CTRL[6:0] with division value - The following MFIO configuration parameters are also required: Signal name Pad name MFIO mode spim1_d0_txd MFIO_MIPS_5 0 spim1_d1_rxd MFIO_MIPS_4 0 spim1_mclk MFIO_MIPS_3 0 spim1_d2 MFIO_MIPS_6 0 spim1_d3 MFIO_MIPS_7 0 spim1_cs0 MFIO_MIPS_0 0 spim1_cs1 MFIO_MIPS_1 0 MFIO_MIPS_58 1 spim1_cs2 MFIO_MIPS_2 0 MFIO_MIPS_55 2 MFIO_MIPS_31 1 spim1_cs3 MFIO_MIPS_56 2 spim1_cs4 MFIO_MIPS_57 2 BUG=chrome-os-partner:31438, chrome-os-partner:32441 TEST=Tested as bare-metal driver on Pistachio FPGA Change-Id: I3b3e4475976e6fba58cef93b12d997ec5cb26341 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 621849942e27f7d6cf2c8ade7f2c4d18d2318b91 Original-Change-Id: Ib257eb6236bd2895281175871b4ab979660f1239 Original-Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com> Original-Reviewed-on: https://chromium-review.googlesource.com/217320 Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: http://review.coreboot.org/9049 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> |
||
|---|---|---|
| 3rdparty@2bc495fd31 | ||
| documentation | ||
| payloads | ||
| src | ||
| util | ||
| .gitignore | ||
| .gitmodules | ||
| .gitreview | ||
| COPYING | ||
| Makefile | ||
| Makefile.inc | ||
| README | ||
| toolchain.inc | ||
README
------------------------------------------------------------------------------- coreboot README ------------------------------------------------------------------------------- coreboot is a Free Software project aimed at replacing the proprietary BIOS (firmware) found in most computers. coreboot performs a little bit of hardware initialization and then executes additional boot logic, called a payload. With the separation of hardware initialization and later boot logic, coreboot can scale from specialized applications that run directly firmware, run operating systems in flash, load custom bootloaders, or implement firmware standards, like PC BIOS services or UEFI. This allows for systems to only include the features necessary in the target application, reducing the amount of code and flash space required. coreboot was formerly known as LinuxBIOS. Payloads -------- After the basic initialization of the hardware has been performed, any desired "payload" can be started by coreboot. See http://www.coreboot.org/Payloads for a list of supported payloads. Supported Hardware ------------------ coreboot supports a wide range of chipsets, devices, and mainboards. For details please consult: * http://www.coreboot.org/Supported_Motherboards * http://www.coreboot.org/Supported_Chipsets_and_Devices Build Requirements ------------------ * gcc / g++ * make Optional: * doxygen (for generating/viewing documentation) * iasl (for targets with ACPI support) * gdb (for better debugging facilities on some targets) * ncurses (for 'make menuconfig') * flex and bison (for regenerating parsers) Building coreboot ----------------- Please consult http://www.coreboot.org/Build_HOWTO for details. Testing coreboot Without Modifying Your Hardware ------------------------------------------------ If you want to test coreboot without any risks before you really decide to use it on your hardware, you can use the QEMU system emulator to run coreboot virtually in QEMU. Please see http://www.coreboot.org/QEMU for details. Website and Mailing List ------------------------ Further details on the project, a FAQ, many HOWTOs, news, development guidelines and more can be found on the coreboot website: http://www.coreboot.org You can contact us directly on the coreboot mailing list: http://www.coreboot.org/Mailinglist Copyright and License --------------------- The copyright on coreboot is owned by quite a large number of individual developers and companies. Please check the individual source files for details. coreboot is licensed under the terms of the GNU General Public License (GPL). Some files are licensed under the "GPL (version 2, or any later version)", and some files are licensed under the "GPL, version 2". For some parts, which were derived from other projects, other (GPL-compatible) licenses may apply. Please check the individual source files for details. This makes the resulting coreboot images licensed under the GPL, version 2.