242 lines
5.2 KiB
Plaintext
242 lines
5.2 KiB
Plaintext
# Sample config file for
|
|
# the Tyan s2880
|
|
# This will make a target directory of ./s2880
|
|
|
|
loadoptions
|
|
|
|
target s4882
|
|
|
|
uses ARCH
|
|
uses CONFIG_COMPRESS
|
|
uses CONFIG_IOAPIC
|
|
uses CONFIG_ROM_STREAM
|
|
uses CONFIG_ROM_STREAM_START
|
|
uses CONFIG_SMP
|
|
uses CONFIG_UDELAY_TSC
|
|
uses CPU_FIXUP
|
|
uses FALLBACK_SIZE
|
|
uses HAVE_FALLBACK_BOOT
|
|
uses HAVE_MP_TABLE
|
|
uses HAVE_PIRQ_TABLE
|
|
uses i586
|
|
uses i686
|
|
uses INTEL_PPRO_MTRR
|
|
uses HEAP_SIZE
|
|
uses IRQ_SLOT_COUNT
|
|
uses k7
|
|
uses k8
|
|
uses MAINBOARD
|
|
uses MAINBOARD_PART_NUMBER
|
|
uses MAINBOARD_VENDOR
|
|
#uses MEMORY_HOLE
|
|
uses PAYLOAD_SIZE
|
|
uses _RAMBASE
|
|
uses _ROMBASE
|
|
uses ROM_IMAGE_SIZE
|
|
uses ROM_SECTION_OFFSET
|
|
uses ROM_SECTION_SIZE
|
|
uses ROM_SIZE
|
|
uses STACK_SIZE
|
|
uses USE_FALLBACK_IMAGE
|
|
uses USE_OPTION_TABLE
|
|
uses HAVE_OPTION_TABLE
|
|
uses CONFIG_CHIP_CONFIGURE
|
|
|
|
uses CONFIG_CONSOLE_SERIAL8250
|
|
uses TTYS0_BAUD
|
|
uses DEFAULT_CONSOLE_LOGLEVEL
|
|
uses MAXIMUM_CONSOLE_LOGLEVEL
|
|
uses DEBUG
|
|
uses CONFIG_MAX_CPUS
|
|
uses CONFIG_LOGICAL_CPUS
|
|
uses CONFIG_MAX_PHYSICAL_CPUS
|
|
uses LINUXBIOS_EXTRA_VERSION
|
|
uses XIP_ROM_SIZE
|
|
uses XIP_ROM_BASE
|
|
|
|
uses HAVE_HARD_RESET
|
|
|
|
#uses CONFIG_VGABIOS
|
|
#uses CONFIG_REALMODE_IDT
|
|
#uses CONFIG_PCIBIOS
|
|
#uses VGABIOS_START
|
|
#uses SCSIFW_START
|
|
|
|
#
|
|
#uses CONFIG_LSI_SCSI_FW_FIXUP
|
|
|
|
option HAVE_HARD_RESET=1
|
|
|
|
option HAVE_OPTION_TABLE=1
|
|
option HAVE_MP_TABLE=1
|
|
option CPU_FIXUP=1
|
|
option CONFIG_UDELAY_TSC=0
|
|
option i686=1
|
|
option i586=1
|
|
option INTEL_PPRO_MTRR=1
|
|
option k7=1
|
|
option k8=1
|
|
option ROM_SIZE=524288
|
|
|
|
#option CONFIG_VGABIOS=0
|
|
#option CONFIG_REALMODE_IDT=0
|
|
#option CONFIG_PCIBIOS=0
|
|
#option VGABIOS_START=0xfff8c000
|
|
#option SCSIFW_START=0xfff80000
|
|
|
|
|
|
option HAVE_FALLBACK_BOOT=1
|
|
|
|
# use the new chip configure code.
|
|
|
|
option CONFIG_CHIP_CONFIGURE=1
|
|
#option CONFIG_LSI_SCSI_FW_FIXUP=1
|
|
|
|
|
|
#
|
|
###
|
|
### Build code to export a programmable irq routing table
|
|
###
|
|
option HAVE_PIRQ_TABLE=1
|
|
option IRQ_SLOT_COUNT=22
|
|
#
|
|
###
|
|
### Build code for SMP support
|
|
### Only worry about 2 micro processors
|
|
###
|
|
option CONFIG_SMP=1
|
|
option CONFIG_MAX_CPUS=4
|
|
option CONFIG_LOGICAL_CPUS=0
|
|
option CONFIG_MAX_PHYSICAL_CPUS=4
|
|
#
|
|
###
|
|
### Build code to setup a generic IOAPIC
|
|
###
|
|
option CONFIG_IOAPIC=1
|
|
#
|
|
###
|
|
### MEMORY_HOLE instructs earlymtrr.inc to
|
|
### enable caching from 0-640KB and to disable
|
|
### caching from 640KB-1MB using fixed MTRRs
|
|
###
|
|
### Enabling this option breaks SMP because secondary
|
|
### CPU identification depends on only variable MTRRs
|
|
### being enabled.
|
|
###
|
|
#option MEMORY_HOLE=0
|
|
#
|
|
###
|
|
### Clean up the motherboard id strings
|
|
###
|
|
option MAINBOARD_PART_NUMBER="S4882"
|
|
option MAINBOARD_VENDOR="Tyan"
|
|
#
|
|
###
|
|
### Compute the location and size of where this firmware image
|
|
### (linuxBIOS plus bootloader) will live in the boot rom chip.
|
|
###
|
|
#option FALLBACK_SIZE=524288
|
|
#option FALLBACK_SIZE=98304
|
|
option FALLBACK_SIZE=131072
|
|
|
|
## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
|
|
option ROM_IMAGE_SIZE=65536
|
|
|
|
|
|
###
|
|
### Compute where this copy of linuxBIOS will start in the boot rom
|
|
###
|
|
#
|
|
###
|
|
|
|
## We do use compressed image
|
|
option CONFIG_COMPRESS=1
|
|
|
|
option CONFIG_CONSOLE_SERIAL8250=1
|
|
option TTYS0_BAUD=115200
|
|
|
|
##
|
|
### Select the linuxBIOS loglevel
|
|
##
|
|
## EMERG 1 system is unusable
|
|
## ALERT 2 action must be taken immediately
|
|
## CRIT 3 critical conditions
|
|
## ERR 4 error conditions
|
|
## WARNING 5 warning conditions
|
|
## NOTICE 6 normal but significant condition
|
|
## INFO 7 informational
|
|
## DEBUG 8 debug-level messages
|
|
## SPEW 9 Way too many details
|
|
|
|
## Request this level of debugging output
|
|
option DEFAULT_CONSOLE_LOGLEVEL=7
|
|
## At a maximum only compile in this level of debugging
|
|
option MAXIMUM_CONSOLE_LOGLEVEL=7
|
|
|
|
option DEBUG=1
|
|
|
|
#
|
|
|
|
## LinuxBIOS C code runs at this location in RAM
|
|
option _RAMBASE=0x004000
|
|
|
|
##
|
|
## Use a 256K stack
|
|
##
|
|
option STACK_SIZE=0x4000
|
|
|
|
##
|
|
## Use a 384K heap
|
|
##
|
|
option HEAP_SIZE=0xa000
|
|
|
|
#
|
|
###
|
|
### Compute the start location and size size of
|
|
### The linuxBIOS bootloader.
|
|
###
|
|
option CONFIG_ROM_STREAM = 1
|
|
|
|
#
|
|
#
|
|
romimage "normal"
|
|
# 48K for SCSI FW
|
|
option ROM_SIZE = 475136
|
|
# 48K for SCSI FW and 48K for ATI ROM
|
|
# option ROM_SIZE = 425984
|
|
option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
|
|
option USE_FALLBACK_IMAGE=0
|
|
option ROM_SECTION_SIZE = (ROM_SIZE - FALLBACK_SIZE)
|
|
option ROM_SECTION_OFFSET= 0
|
|
|
|
option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
|
|
option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
|
|
option _ROMBASE = (CONFIG_ROM_STREAM_START + PAYLOAD_SIZE)
|
|
|
|
option XIP_ROM_SIZE = FALLBACK_SIZE
|
|
option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
|
|
|
|
mainboard tyan/s4882
|
|
payload ../../tg3--ide_disk.zelf
|
|
end
|
|
|
|
romimage "fallback"
|
|
option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
|
|
option USE_FALLBACK_IMAGE=1
|
|
option ROM_SECTION_SIZE = FALLBACK_SIZE
|
|
option ROM_SECTION_OFFSET= (ROM_SIZE - FALLBACK_SIZE)
|
|
|
|
option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
|
|
option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
|
|
option _ROMBASE = (CONFIG_ROM_STREAM_START + PAYLOAD_SIZE)
|
|
|
|
option XIP_ROM_SIZE = FALLBACK_SIZE
|
|
option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
|
|
|
|
mainboard tyan/s4882
|
|
payload ../../tg3--ide_disk.zelf
|
|
# payload ../../filo.elf.d
|
|
end
|
|
|
|
buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback"
|