coreboot-kgpe-d16/documentation/AMD-S3.txt

129 lines
5.5 KiB
Plaintext

_____ ____ _____ ______ ____ ____ ____ _______
/ ____/ __ \| __ \| ____| _ \ / __ \ / __ \__ __|
| | | | | | |__) | |__ | |_) | | | | | | | | |
| | | | | | _ /| __| | _ <| | | | | | | | |
| |___| |__| | | \ \| |____| |_) | |__| | |__| | | |
\_____\____/|_| \_\______|____/ \____/ \____/ |_|
__ __ _____ _____ ____
/\ | \/ | __ \ / ____| |___ \
/ \ | \ / | | | | | (___ __) |
/ /\ \ | |\/| | | | | \___ \ |__ <
/ ____ \| | | | |__| | ____) | ___) |
/_/ \_\_| |_|_____/ |_____/ |____/
S3 in Coreboot (V 1.1)
----------------------------------------
Zheng Bao
<zheng.bao@amd.com>
<fishbaozi@gmail.com>
Introduction
============
This document is about how the feature S3 is implemented on coreboot,
specificly on AMD platform. This topic deals with ACPI spec, hardware,
BIOS, OS. We try to help coreboot users to realize their own S3.
S3 in a nutshell
================
The S3 sleeping state is a low wake latency sleeping state where all
system context is lost except system memory. [1]. S3 is a ACPI
definition.
To enter S3, write 3 in SLP_TYPx and set the SLP_EN bit (See ACPI
registers). But if you do that, board can not resume at where it
sleeps, because you don't save the context. More often than not, we
make the board go into S3 by the tools which OSes provide. For
windows, click Start->sleep. For linux, some distribution provide a
tools called pm-suspend, which can make the system goto S3. If
pm-suspend is not available, we can run "echo mem > /sys/power/state",
but this way may not save all the needed context.
In S3 state, the power is off. So when the power button is pressed,
BIOS runs as it does in cold boot. If BIOS didn't detect whether
board boots or resumes, it would go the same way as boot. It is not
what we expect. BIOS detects the SLP_TYPx. If it is 3, it means BIOS
are waking up.
BIOS is responsible for restore the machine state as it is before
sleep. It needs restore the memory controller, not overwriting memory
which is not marked as reserved. For the peripheral which loses its
registers, BIOS needs to write the original value.
When everything is done, BIOS needs to find out the wakeup vector
provided by OSes and jump there. OSes also have work to do. We can go
to linux kernel or some other open source projects to find out how they
handle S3 resume.
ACPI registers
==============
ACPI specification defines a group of registers. OSes handle all these
registers to read and write status to all the platform.
On AMD platform, these registers are provided by southbridge. For
example, Hudson uses PMIO 60:6F to define ACPI registers.
OSes don't have any specific driver to know where these registers
are. BIOS has the responsibility to allocated the IO resources and
write all these address to FADT, a ACPI defined table.
Memory Layout
=============
Restoring memory is the most important job done by BIOS. When the
power is off, the memory is maintained by standby power. BIOS need to
make sure that when flow goes to OS, everything in memory should be
the same as it was.
The chip vendor will provide a way, or code, to wake up the memory
from sleeping. In AGESA 2008 arch, it is called AmdInitResume.
The BIOS itself needs some memory to run. Either, BIOS marks the erea
as reserved in e820, or BIOS saves the content into reserved space.
Here is the address Map for S3 Resume. Assumingly the total memory is 1GB.
00000000 --- 00100000 BIOS Reserved area.
00100000 --- 00200000 Free
00200000 --- 01000000 Coreboot ramstage area.
01000000 --- 2e160000 Free
2e160000 --- 2e170000 ACPI table
2e170000 --- 2ef70000 OSRAM
2ef70000 --- 2efe0000 Stack in highmem
2efe0000 --- 2f000000 heap in highmem
2f000000 TOM
AMD requirements in S3
======================
Chip vendor like AMD will provide bunch of routines to restore the
board.[2]
* AmdS3Save: It is called in cold boot, save required register into
non-volatile storage. Currently, we use SPI flash to store the data.
* AmdInitResume: Restore the memory controller.
* AmdS3LateRestore: Called after AmdInitResume, restore other
register that memory.
* (SouthBridge)InitS3EarlyRestore, (SouthBridge)InitS3LateRestore:
Provided by Southbridge vendor code. Early is called before PCI
enumeration, and Late is called after that.
Lifecycle of booting, sleeping and waking Coreboot and Ubuntu
=============================================================
1. Cold boot.
For a system with S3 feature, the BIOS needs to save some data to
non-volitile storage at cold boot stage. What data need to be save are
provided by AmdS3Save. After the wrapper calls the AmdS3Save, it gets
the VolatileStorage and NvStorage, which are where the data are
located. It is the wrappers's responsibility to save the data.[3][4]
Currently, the wrappers allocate a CBFS modules in BIOS image. Todo
that, the wrapper needs to have the ability to write flash chips. It
is not as comprehensive as flashrom. But for the SST chip on Parmer,
MX chip on Thather, coreboot works well.[5]
2. OS goes in S3.
3. BIOS detect S3 wakeup
4. OS resumes.
Reference
=========
[1] ACPI40a, http://www.acpi.info/spec40a.htm
[2] Coreboot Vendorcode, {top}/src/vendorcode/amd/agesa/{family}/Proc/Common/
[3] Coreboot AGESA wrapper, {top}/src/mainboard/amd/parmer/agesawrapper.c
[4] Coreboot AGESA wrapper, {top}/src/cpu/amd/agesa/s3_resume.c
[5] Coreboot Southbridge, {top}/src/southbridge/amd/agesa/hudson/spi.c