coreboot-kgpe-d16/payloads/libpayload/drivers/udc/chipidea_priv.h

169 lines
5.1 KiB
C

/*
* This file is part of the libpayload project.
*
* Copyright (C) 2015 Google Inc.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*/
#ifndef __CHIPIDEA_PRIV_H__
#define __CHIPIDEA_PRIV_H__
#include <queue.h>
struct chipidea_opreg {
uint8_t pad0[0x130];
uint32_t usbcmd; // 0x130
uint32_t usbsts; // 0x134
uint32_t pad138[3];
uint32_t usbadr; // 0x144
/* 31:25: address
* 24: staging: 1 -> commit new address after
* next ctrl-in on ep0
*/
uint32_t epbase; // 0x148
uint32_t pad14c[10];
uint32_t portsc; // 0x174
uint32_t pad178[15];
uint32_t devlc; // 0x1b4
/* 25:26: host-desired USB version
* 23: force full speed */
uint32_t pad1b8[16];
uint32_t usbmode; // 0x1f8
/* 0:1: 2 -> device mode */
uint32_t pad1fc[3];
uint32_t epsetupstat; // 0x208
/* 0:15: 1 -> epX received setup packet */
uint32_t epprime; // 0x20c
/* 0:15: 1 -> rx buffer for epX (OUT) is primed
* (ie. ready for controller-side processing)
* 16:31: 1 -> tx buffer for ep(X-16) (IN/INTR) is primed
* (ie. ready for controller-side processing)
*
* controller will read new td from qh and process it,
* then set the bit to 0
*/
uint32_t epflush; // 0x210
/* 0:31: 1 -> flush buffer (as defined in epprime),
* so it's uninitialized again.
* controller resets to 0 when done
*/
uint32_t epstat; // 0x214
/* 0:31: 1 -> command in epprime is done, EP is ready
* (which may be later than epprime reset)
*/
uint32_t epcomplete; // 0x218
/* 0:15: 1 -> incoming out/setup packet for epX was handled.
* software should check QH state
* 16:31: 1 -> incoming intr/in packet for ep(X-16) was
* handled. software should check QH state
*/
uint32_t epctrl[16]; // 0x21c
/* epctrl[0] is hardcoded as enabled control endpoint.
* TXS/RXS for stalling can be written.
*
* 23: TXE tx endpoint enable
* 22: TXR reset tx data toggle (for every configuration event)
* 18:19: 0=ctrl, 1=isoc, 2=bulk, 3=intr endpoint
* 16: TXS stall tx
*
* 7: RXE rx endpoint enable
* 6: RXR reset rx data toggle (for every configuration event)
* 2:3: endpoint type (like 18:19)
* 0: RXS stall rx
*/
uint32_t pad25c[0x69]; // 0x25c
uint32_t susp_ctrl; // 0x400
};
#define CI_PDATA(ctrl) ((struct chipidea_pdata *)((ctrl)->pdata))
#define CI_QHELEMENTS 32
#define QH_NO_AUTO_ZLT (1 << 29) /* no automatic ZLT handling by chipset */
#define QH_MPS(x) ((x) << 16)
#define QH_IOS (1 << 15) /* IRQ on setup */
#define TD_INFO_LEN(x) ((x) << 16)
#define TD_INFO_IOC (1 << 15)
#define TD_INFO_ACTIVE (1 << 7)
#define TD_TERMINATE 1
#define USBCMD_8MICRO (8 << 16)
#define USBCMD_RST 2
#define USBCMD_RUN 1
#define USBSTS_SLI (1 << 8)
#define USBSTS_URI (1 << 6)
#define USBSTS_PCI (1 << 2)
#define USBSTS_UEI (1 << 1)
#define USBSTS_UI (1 << 0)
#define DEVLC_HOSTSPEED(x) (x << 25)
#define DEVLC_HOSTSPEED_MASK DEVLC_HOSTSPEED(3)
struct td {
/* points to next td */
uint32_t next;
uint32_t info;
/* page0..4 are like EHCI pages: up to 4k each
* page0 from addr to page end, page4 to its length
*/
uint32_t page0;
uint32_t page1;
uint32_t page2;
uint32_t page3;
uint32_t page4;
uint32_t res;
};
struct qh {
uint32_t config;
uint32_t current;
struct td td;
/* contains the data of a setup request */
uint8_t setup_data[8];
uint32_t res[4];
};
struct job {
SIMPLEQ_ENTRY(job) queue; // linkage
struct td *tds; // for later free()ing
int td_count;
void *data;
size_t length;
int zlp; // append zero length packet?
int autofree; // free after processing?
};
SIMPLEQ_HEAD(job_queue, job);
struct chipidea_pdata {
struct chipidea_opreg *opreg;
struct qh *qhlist;
struct job_queue job_queue[16][2];
int ep_busy[16][2];
};
#endif