coreboot-libre-fam15h-rdimm/3rdparty/chromeec/board/jacuzzi/board.h

135 lines
3.0 KiB
C
Raw Permalink Normal View History

2024-03-04 11:14:53 +01:00
/* Copyright 2018 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Configuration for Kukui */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
#define VARIANT_KUKUI_BATTERY_SMART
#define VARIANT_KUKUI_CHARGER_ISL9238
#ifndef SECTION_IS_RW
#define VARIANT_KUKUI_NO_SENSORS
#endif /* SECTION_IS_RW */
#include "baseboard.h"
/* TODO(b:135086465) led implementation */
#undef CONFIG_LED_COMMON
#define CONFIG_BATTERY_HW_PRESENT_CUSTOM
#define CONFIG_CHARGER_PSYS
#define CONFIG_BC12_DETECT_PI3USB9201
#define CONFIG_EXTPOWER_GPIO
#undef CONFIG_EXTPOWER_DEBOUNCE_MS
#define CONFIG_EXTPOWER_DEBOUNCE_MS 200
#define CONFIG_USB_PD_TCPM_FUSB302
#define CONFIG_USB_PD_DISCHARGE_GPIO
#define CONFIG_USB_PD_VBUS_MEASURE_NOT_PRESENT
#define CONFIG_USB_MUX_IT5205
/* Motion Sensors */
#ifdef SECTION_IS_RW
#define CONFIG_MAG_BMI160_BMM150
#define CONFIG_ACCELGYRO_SEC_ADDR_FLAGS BMM150_ADDR0_FLAGS
#define CONFIG_MAG_CALIBRATE
#define CONFIG_ACCELGYRO_BMI160
#define CONFIG_ACCEL_INTERRUPTS
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL)
#define CONFIG_ALS
#define ALS_COUNT 1
#define CONFIG_ALS_TCS3400
#define CONFIG_ALS_TCS3400_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(CLEAR_ALS)
#define CONFIG_ALS_TCS3400_EMULATED_IRQ_EVENT
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(CLEAR_ALS)
#endif /* SECTION_IS_RW */
/* I2C ports */
#define I2C_PORT_BC12 0
#define I2C_PORT_TCPC0 0
#define I2C_PORT_USB_MUX 0
#define I2C_PORT_BATTERY 1
#define I2C_PORT_CHARGER board_get_charger_i2c()
#define I2C_PORT_IO_EXPANDER_IT8801 1
/* Enable Accel over SPI */
#define CONFIG_SPI_ACCEL_PORT 0 /* The first SPI master port (SPI2) */
#define CONFIG_KEYBOARD_PROTOCOL_MKBP
#define CONFIG_MKBP_EVENT
#define CONFIG_MKBP_USE_GPIO
/* Define the MKBP events which are allowed to wakeup AP in S3. */
#define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \
(EC_HOST_EVENT_MASK(EC_HOST_EVENT_LID_OPEN) |\
EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON))
#ifndef __ASSEMBLER__
enum adc_channel {
/* Real ADC channels begin here */
ADC_BOARD_ID = 0,
ADC_EC_SKU_ID,
ADC_BATT_ID,
ADC_CH_COUNT
};
/* power signal definitions */
enum power_signal {
AP_IN_S3_L,
PMIC_PWR_GOOD,
/* Number of signals */
POWER_SIGNAL_COUNT,
};
/* Motion sensors */
enum sensor_id {
LID_ACCEL = 0,
LID_GYRO,
LID_MAG,
CLEAR_ALS,
RGB_ALS,
VSYNC,
SENSOR_COUNT,
};
enum charge_port {
CHARGE_PORT_USB_C,
};
enum battery_type {
BATTERY_PANASONIC_AC15A3J,
BATTERY_TYPE_COUNT,
};
#include "gpio_signal.h"
#include "registers.h"
#ifdef SECTION_IS_RO
/* Interrupt handler for emmc task */
void emmc_cmd_interrupt(enum gpio_signal signal);
#endif
void board_reset_pd_mcu(void);
int board_get_version(void);
int board_is_sourcing_vbus(int port);
/* returns the i2c port number of charger */
int board_get_charger_i2c(void);
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */