335 lines
9.8 KiB
C
335 lines
9.8 KiB
C
|
/* Copyright 2016 The Chromium OS Authors. All rights reserved.
|
||
|
|
* Use of this source code is governed by a BSD-style license that can be
|
||
|
|
* found in the LICENSE file.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Reef board configuration */
|
||
|
|
|
||
|
|
#ifndef __CROS_EC_BOARD_H
|
||
|
|
#define __CROS_EC_BOARD_H
|
||
|
|
|
||
|
|
/*
|
||
|
|
* By default, enable all console messages excepted HC, ACPI and event:
|
||
|
|
* The sensor stack is generating a lot of activity.
|
||
|
|
*/
|
||
|
|
#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_EVENTS) | CC_MASK(CC_LPC)))
|
||
|
|
#undef CONFIG_HOSTCMD_DEBUG_MODE
|
||
|
|
#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF
|
||
|
|
|
||
|
|
|
||
|
|
/* EC console commands */
|
||
|
|
#define CONFIG_CMD_ACCELS
|
||
|
|
#define CONFIG_CMD_ACCEL_INFO
|
||
|
|
#define CONFIG_CMD_BATT_MFG_ACCESS
|
||
|
|
#define CONFIG_CMD_CHARGER_ADC_AMON_BMON
|
||
|
|
#define CONFIG_CHARGER_SENSE_RESISTOR 10
|
||
|
|
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10
|
||
|
|
#define BD9995X_IOUT_GAIN_SELECT \
|
||
|
|
BD9995X_CMD_PMON_IOUT_CTRL_SET_IOUT_GAIN_SET_20V
|
||
|
|
|
||
|
|
#define CONFIG_CHARGER_PSYS_READ
|
||
|
|
#define BD9995X_PSYS_GAIN_SELECT \
|
||
|
|
BD9995X_CMD_PMON_IOUT_CTRL_SET_PMON_GAIN_SET_02UAW
|
||
|
|
|
||
|
|
#define CONFIG_CMD_I2C_STRESS_TEST
|
||
|
|
#define CONFIG_CMD_I2C_STRESS_TEST_ACCEL
|
||
|
|
#define CONFIG_CMD_I2C_STRESS_TEST_ALS
|
||
|
|
#define CONFIG_CMD_I2C_STRESS_TEST_BATTERY
|
||
|
|
#define CONFIG_CMD_I2C_STRESS_TEST_CHARGER
|
||
|
|
#define CONFIG_CMD_I2C_STRESS_TEST_TCPC
|
||
|
|
|
||
|
|
/* Battery */
|
||
|
|
#define CONFIG_BATTERY_DEVICE_CHEMISTRY "LION"
|
||
|
|
#define CONFIG_BATTERY_CUT_OFF
|
||
|
|
#define CONFIG_BATTERY_PRESENT_CUSTOM
|
||
|
|
#define CONFIG_BATTERY_SMART
|
||
|
|
|
||
|
|
/* Charger */
|
||
|
|
#define CONFIG_CHARGE_MANAGER
|
||
|
|
#define CONFIG_CHARGE_RAMP_SW
|
||
|
|
#define CONFIG_CHARGER
|
||
|
|
#define CONFIG_CHARGER_BD9995X
|
||
|
|
#define CONFIG_CHARGER_BD9995X_CHGEN
|
||
|
|
#define CONFIG_CHARGER_DISCHARGE_ON_AC
|
||
|
|
#define CONFIG_CHARGER_INPUT_CURRENT 512
|
||
|
|
#define CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT 1
|
||
|
|
#define CONFIG_CHARGER_LIMIT_POWER_THRESH_CHG_MW 18000
|
||
|
|
#define CONFIG_CHARGER_MAINTAIN_VBAT
|
||
|
|
#define CONFIG_CHARGER_MIN_BAT_PCT_FOR_POWER_ON 1
|
||
|
|
#define CONFIG_USB_CHARGER
|
||
|
|
#define CONFIG_CHARGER_PROFILE_OVERRIDE
|
||
|
|
#define CONFIG_CHARGER_PROFILE_OVERRIDE_COMMON
|
||
|
|
#undef CONFIG_CHARGER_PROFILE_VOLTAGE_RANGES
|
||
|
|
#define CONFIG_CHARGER_PROFILE_VOLTAGE_RANGES 3
|
||
|
|
#define CONFIG_CHARGE_MANAGER_EXTERNAL_POWER_LIMIT
|
||
|
|
|
||
|
|
/* USB-A config */
|
||
|
|
#define CONFIG_USB_PORT_POWER_SMART
|
||
|
|
#define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP
|
||
|
|
#define CONFIG_USB_PORT_POWER_SMART_SIMPLE
|
||
|
|
#undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT
|
||
|
|
#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1
|
||
|
|
#define GPIO_USB1_ILIM_SEL GPIO_USB_A_CHARGE_EN_L
|
||
|
|
#define GPIO_USB_CTL1 GPIO_EN_PP5000
|
||
|
|
|
||
|
|
#define CONFIG_TABLET_MODE
|
||
|
|
|
||
|
|
/* USB PD config */
|
||
|
|
#define CONFIG_CMD_PD_CONTROL
|
||
|
|
#define CONFIG_USB_PD_ALT_MODE
|
||
|
|
#define CONFIG_USB_PD_ALT_MODE_DFP
|
||
|
|
#define CONFIG_USB_PD_DUAL_ROLE
|
||
|
|
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
|
||
|
|
#define CONFIG_USB_PD_DISCHARGE_TCPC
|
||
|
|
#define CONFIG_USB_PD_LOGGING
|
||
|
|
#define CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT TYPEC_RP_3A0
|
||
|
|
#define CONFIG_USB_PD_PORT_COUNT 2
|
||
|
|
#define CONFIG_USB_PD_VBUS_DETECT_CHARGER
|
||
|
|
#define CONFIG_USB_PD_TCPC_LOW_POWER
|
||
|
|
#define CONFIG_USB_PD_TCPM_MUX /* for both PS8751 and ANX3429 */
|
||
|
|
#define CONFIG_USB_PD_TCPM_ANX3429 /* Silicon on Reef is ANX3429 */
|
||
|
|
#define CONFIG_USB_PD_TCPM_PS8751
|
||
|
|
#define CONFIG_USB_PD_TCPM_TCPCI
|
||
|
|
#define CONFIG_USB_PD_TRY_SRC
|
||
|
|
#define CONFIG_USB_POWER_DELIVERY
|
||
|
|
#define CONFIG_USB_PD_COMM_LOCKED
|
||
|
|
|
||
|
|
#define CONFIG_USBC_SS_MUX
|
||
|
|
#define CONFIG_USBC_SS_MUX_DFP_ONLY
|
||
|
|
#define CONFIG_USBC_VCONN
|
||
|
|
#define CONFIG_USBC_VCONN_SWAP
|
||
|
|
|
||
|
|
/* SoC / PCH */
|
||
|
|
#define CONFIG_HOSTCMD_LPC
|
||
|
|
#define CONFIG_CHIPSET_APOLLOLAKE
|
||
|
|
#define CONFIG_CHIPSET_RESET_HOOK
|
||
|
|
#define CONFIG_POWER_BUTTON
|
||
|
|
#define CONFIG_POWER_BUTTON_X86
|
||
|
|
#define CONFIG_POWER_COMMON
|
||
|
|
#define CONFIG_POWER_S0IX
|
||
|
|
#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE
|
||
|
|
|
||
|
|
/* EC */
|
||
|
|
#define CONFIG_ADC
|
||
|
|
#define CONFIG_BOARD_VERSION_CUSTOM
|
||
|
|
#define CONFIG_EXTPOWER_GPIO
|
||
|
|
#undef CONFIG_EXTPOWER_DEBOUNCE_MS
|
||
|
|
#define CONFIG_EXTPOWER_DEBOUNCE_MS 1000
|
||
|
|
#define CONFIG_FPU
|
||
|
|
#define CONFIG_HOSTCMD_FLASH_SPI_INFO
|
||
|
|
#define CONFIG_I2C
|
||
|
|
#define CONFIG_I2C_MASTER
|
||
|
|
#define CONFIG_KEYBOARD_BOARD_CONFIG
|
||
|
|
#define CONFIG_KEYBOARD_PROTOCOL_8042
|
||
|
|
#define CONFIG_KEYBOARD_COL2_INVERTED
|
||
|
|
#define CONFIG_KEYBOARD_PWRBTN_ASSERTS_KSI2
|
||
|
|
#define CONFIG_LED_COMMON
|
||
|
|
#define CONFIG_LID_SWITCH
|
||
|
|
#define CONFIG_LOW_POWER_IDLE
|
||
|
|
#define CONFIG_LTO
|
||
|
|
#define CONFIG_POWER_SIGNAL_INTERRUPT_STORM_DETECT_THRESHOLD 30
|
||
|
|
#define CONFIG_PWM
|
||
|
|
#define CONFIG_TEMP_SENSOR
|
||
|
|
#define CONFIG_THERMISTOR_NCP15WB
|
||
|
|
#define CONFIG_DPTF
|
||
|
|
#define CONFIG_SCI_GPIO GPIO_PCH_SCI_L
|
||
|
|
#define CONFIG_VOLUME_BUTTONS
|
||
|
|
#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
|
||
|
|
#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
|
||
|
|
#define CONFIG_VBOOT_HASH
|
||
|
|
#define CONFIG_BACKLIGHT_LID
|
||
|
|
#define CONFIG_WIRELESS
|
||
|
|
#define CONFIG_WIRELESS_SUSPEND EC_WIRELESS_SWITCH_WLAN_POWER
|
||
|
|
#define CONFIG_WLAN_POWER_ACTIVE_LOW
|
||
|
|
#define WIRELESS_GPIO_WLAN_POWER GPIO_WIRELESS_GPIO_WLAN_POWER
|
||
|
|
#define CONFIG_PWR_STATE_DISCHARGE_FULL
|
||
|
|
|
||
|
|
/*
|
||
|
|
* During shutdown sequence TPS65094x PMIC turns off the sensor rails
|
||
|
|
* asynchronously to the EC. If we access the sensors when the sensor power
|
||
|
|
* rails are off we get I2C errors. To avoid this issue, defer switching
|
||
|
|
* the sensors rate if in S3. By the time deferred function is serviced if
|
||
|
|
* the chipset is in S5 we can back out from switching the sensor rate.
|
||
|
|
*
|
||
|
|
* Time taken by V1P8U rail to go down from S3 is 30ms to 60ms hence defer
|
||
|
|
* the sensor switching after 60ms.
|
||
|
|
*/
|
||
|
|
#undef CONFIG_MOTION_SENSE_SUSPEND_DELAY_US
|
||
|
|
#define CONFIG_MOTION_SENSE_SUSPEND_DELAY_US (MSEC * 60)
|
||
|
|
|
||
|
|
/*
|
||
|
|
* MEC1701H loads firmware using QMSPI controller
|
||
|
|
* CONFIG_SPI_FLASH_PORT is the index into
|
||
|
|
* spi_devices[] in board.c
|
||
|
|
*/
|
||
|
|
#define CONFIG_SPI_FLASH_PORT 0
|
||
|
|
#define CONFIG_SPI_FLASH
|
||
|
|
|
||
|
|
#define CONFIG_FLASH_SIZE 524288
|
||
|
|
#define CONFIG_SPI_FLASH_REGS
|
||
|
|
#define CONFIG_SPI_FLASH_W25Q40 /* FIXME: Should be GD25LQ40? */
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Enable 1 slot of secure temporary storage to support
|
||
|
|
* suspend/resume with read/write memory training.
|
||
|
|
*/
|
||
|
|
#define CONFIG_VSTORE
|
||
|
|
#define CONFIG_VSTORE_SLOT_COUNT 1
|
||
|
|
|
||
|
|
/* Optional feature - used by MCHP */
|
||
|
|
#define CONFIG_CLOCK_CRYSTAL /* interposer board uses parallel crystal */
|
||
|
|
#define CONFIG_WATCHDOG_HELP /* required for MCHP MEC17xx */
|
||
|
|
#define CONFIG_BOARD_PRE_INIT
|
||
|
|
|
||
|
|
/* I2C ports */
|
||
|
|
#define I2C_CONTROLLER_COUNT 4
|
||
|
|
#define I2C_PORT_COUNT 5
|
||
|
|
|
||
|
|
#define I2C_PORT_GYRO MCHP_I2C_PORT6
|
||
|
|
#define I2C_PORT_LID_ACCEL MCHP_I2C_PORT7
|
||
|
|
#define I2C_PORT_ALS MCHP_I2C_PORT7
|
||
|
|
#define I2C_PORT_BARO MCHP_I2C_PORT7
|
||
|
|
#define I2C_PORT_BATTERY MCHP_I2C_PORT3
|
||
|
|
#define I2C_PORT_CHARGER MCHP_I2C_PORT3
|
||
|
|
/* Accelerometer and Gyroscope are the same device. */
|
||
|
|
#define I2C_PORT_ACCEL I2C_PORT_GYRO
|
||
|
|
|
||
|
|
/* Sensors */
|
||
|
|
#define CONFIG_MKBP_EVENT
|
||
|
|
#define CONFIG_MKBP_USE_HOST_EVENT
|
||
|
|
#define CONFIG_ACCELGYRO_BMI160
|
||
|
|
#define CONFIG_ACCEL_INTERRUPTS
|
||
|
|
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
|
||
|
|
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
|
||
|
|
#define CONFIG_MAG_BMI160_BMM150
|
||
|
|
#define CONFIG_ACCELGYRO_SEC_ADDR_FLAGS BMM150_ADDR0_FLAGS
|
||
|
|
#define CONFIG_MAG_CALIBRATE
|
||
|
|
#define CONFIG_ACCEL_KX022
|
||
|
|
#define CONFIG_ALS_OPT3001
|
||
|
|
#define CONFIG_BARO_BMP280
|
||
|
|
#define CONFIG_LID_ANGLE
|
||
|
|
#define CONFIG_LID_ANGLE_UPDATE
|
||
|
|
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
|
||
|
|
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
|
||
|
|
|
||
|
|
/* Enable sensor fifo, must also define the _SIZE and _THRES */
|
||
|
|
#define CONFIG_ACCEL_FIFO
|
||
|
|
/* FIFO size is in power of 2. */
|
||
|
|
#define CONFIG_ACCEL_FIFO_SIZE 1024
|
||
|
|
/* Depends on how fast the AP boots and typical ODRs */
|
||
|
|
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)
|
||
|
|
|
||
|
|
|
||
|
|
#ifndef __ASSEMBLER__
|
||
|
|
|
||
|
|
#include "gpio_signal.h"
|
||
|
|
#include "registers.h"
|
||
|
|
|
||
|
|
/* ADC signal */
|
||
|
|
enum adc_channel {
|
||
|
|
ADC_TEMP_SENSOR_CHARGER, /* ADC0 */
|
||
|
|
ADC_TEMP_SENSOR_AMB, /* ADC1 */
|
||
|
|
ADC_BOARD_ID, /* ADC2 */
|
||
|
|
ADC_CH_COUNT
|
||
|
|
};
|
||
|
|
|
||
|
|
enum pwm_channel {
|
||
|
|
PWM_CH_LED_GREEN = 0,
|
||
|
|
PWM_CH_LED_RED,
|
||
|
|
/* Number of PWM channels */
|
||
|
|
PWM_CH_COUNT
|
||
|
|
};
|
||
|
|
|
||
|
|
enum temp_sensor_id {
|
||
|
|
TEMP_SENSOR_BATTERY = 0,
|
||
|
|
TEMP_SENSOR_AMBIENT,
|
||
|
|
TEMP_SENSOR_CHARGER,
|
||
|
|
TEMP_SENSOR_COUNT
|
||
|
|
};
|
||
|
|
|
||
|
|
/* MCHP - new Reef code not using TASK_ALS */
|
||
|
|
/*
|
||
|
|
* For backward compatibility, to report ALS via ACPI,
|
||
|
|
* Define the number of ALS sensors: motion_sensor copy the data to the ALS
|
||
|
|
* memmap region.
|
||
|
|
*/
|
||
|
|
#define CONFIG_ALS
|
||
|
|
#define ALS_COUNT 1
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Motion sensors:
|
||
|
|
* When reading through IO memory is set up for sensors (LPC is used),
|
||
|
|
* the first 2 entries must be accelerometers, then gyroscope.
|
||
|
|
* For BMI160, accel, gyro and compass sensors must be next to each other.
|
||
|
|
*/
|
||
|
|
enum sensor_id {
|
||
|
|
LID_ACCEL = 0,
|
||
|
|
BASE_ACCEL,
|
||
|
|
BASE_GYRO,
|
||
|
|
BASE_MAG,
|
||
|
|
BASE_BARO,
|
||
|
|
LID_ALS, /* firmware-reef-9042.B doesn't have this */
|
||
|
|
SENSOR_COUNT,
|
||
|
|
};
|
||
|
|
|
||
|
|
enum reef_board_version {
|
||
|
|
BOARD_VERSION_UNKNOWN = -1,
|
||
|
|
BOARD_VERSION_1,
|
||
|
|
BOARD_VERSION_2,
|
||
|
|
BOARD_VERSION_3,
|
||
|
|
BOARD_VERSION_4,
|
||
|
|
BOARD_VERSION_5,
|
||
|
|
BOARD_VERSION_6,
|
||
|
|
BOARD_VERSION_7,
|
||
|
|
BOARD_VERSION_8,
|
||
|
|
BOARD_VERSION_COUNT,
|
||
|
|
};
|
||
|
|
|
||
|
|
/* TODO: determine the following board specific type-C power constants */
|
||
|
|
/* FIXME(dhendrix): verify all of the below PD_* numbers */
|
||
|
|
/*
|
||
|
|
* delay to turn on the power supply max is ~16ms.
|
||
|
|
* delay to turn off the power supply max is about ~180ms.
|
||
|
|
*/
|
||
|
|
#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */
|
||
|
|
#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */
|
||
|
|
|
||
|
|
/* delay to turn on/off vconn */
|
||
|
|
#define PD_VCONN_SWAP_DELAY 5000 /* us */
|
||
|
|
|
||
|
|
/* Define typical operating power and max power */
|
||
|
|
#define PD_OPERATING_POWER_MW 15000
|
||
|
|
#define PD_MAX_POWER_MW 45000
|
||
|
|
#define PD_MAX_CURRENT_MA 3000
|
||
|
|
#define PD_MAX_VOLTAGE_MV 20000
|
||
|
|
|
||
|
|
/* Reset PD MCU */
|
||
|
|
void board_reset_pd_mcu(void);
|
||
|
|
|
||
|
|
int board_get_version(void);
|
||
|
|
|
||
|
|
void board_set_tcpc_power_mode(int port, int mode);
|
||
|
|
void board_print_tcpc_fw_version(int port);
|
||
|
|
|
||
|
|
/* Map I2C port to controller */
|
||
|
|
int board_i2c_p2c(int port);
|
||
|
|
|
||
|
|
/* Return the two slave addresses the specified
|
||
|
|
* controller will respond to when controller
|
||
|
|
* is acting as a slave.
|
||
|
|
* b[6:0] = b[7:1] of I2C address 1
|
||
|
|
* b[14:8] = b[7:1] of I2C address 2
|
||
|
|
*/
|
||
|
|
uint16_t board_i2c_slave_addrs(int controller);
|
||
|
|
|
||
|
|
/* MCHP - firwmare-reef-9042.B does have LID_ALS bit
|
||
|
|
* because its using TASK_ALS ?
|
||
|
|
*/
|
||
|
|
/* Sensors without hardware FIFO are in forced mode */
|
||
|
|
#define CONFIG_ACCEL_FORCE_MODE_MASK \
|
||
|
|
(BIT(LID_ACCEL) | BIT(BASE_BARO) | BIT(LID_ALS))
|
||
|
|
|
||
|
|
#endif /* !__ASSEMBLER__ */
|
||
|
|
|
||
|
|
#endif /* __CROS_EC_BOARD_H */
|