coreboot-libre-fam15h-rdimm/3rdparty/chromeec/board/arcada_ish/board.h

128 lines
3.2 KiB
C
Raw Normal View History

2024-03-04 11:14:53 +01:00
/* Copyright 2018 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Arcada ISH board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/*
* By default, enable all console messages except HC, ACPI and event
* The sensor stack is generating a lot of activity.
*/
#undef CONFIG_HOSTCMD_DEBUG_MODE
#define CONFIG_HOSTCMD_DEBUG_MODE HCDEBUG_OFF
/* ISH specific*/
#undef CONFIG_DEBUG_ASSERT
#define CONFIG_CLOCK_CRYSTAL
/* EC */
#define CONFIG_FLASH_SIZE 0x80000
#define CONFIG_FPU
#define CONFIG_I2C
#define CONFIG_I2C_MASTER
#define CONFIG_ACCEL_LNG2DM /* Base sensor: LNG2DM
* (uses LIS2DH driver)
*/
#define CONFIG_ACCELGYRO_LSM6DSM /* Lid sensor: LSM6DS3
* (uses LSM6DSM driver)
*/
#define CONFIG_MAG_LIS2MDL /* Lid sensor: LIS2DML */
#define CONFIG_MAG_CALIBRATE
#define CONFIG_ACCEL_INTERRUPTS
/* Enable sensor fifo, must also define the _SIZE and _THRES */
#define CONFIG_ACCEL_FIFO
/* FIFO size is a power of 2. */
#define CONFIG_ACCEL_FIFO_SIZE 256
/* Depends on how fast the AP boots and typical ODRs. */
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)
/* Sensors without hardware FIFO are in forced mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK (BIT(BASE_ACCEL) | BIT(LID_MAG))
#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(LID_ACCEL)
#define CONFIG_MKBP_EVENT
#define CONFIG_MKBP_USE_HECI
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_TABLET_MODE
#define CONFIG_GMR_TABLET_MODE
#define CONFIG_GMR_TABLET_MODE_CUSTOM
#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L
/* DMA paging between SRAM and DRAM */
#define CONFIG_DMA_PAGING
/* Host command over HECI */
#define CONFIG_HOSTCMD_HECI
/* I2C ports */
#define I2C_PORT_SENSOR ISH_I2C0
#define CONFIG_CMD_I2C_XFER
/* EC Console Commands */
#define CONFIG_CMD_ACCELS
#define CONFIG_CMD_ACCEL_INFO
#define CONFIG_CMD_TIMERINFO
/* Undefined features */
#undef CONFIG_CMD_HASH
#undef CONFIG_CMD_I2C_SCAN
#undef CONFIG_CMD_KEYBOARD
#undef CONFIG_CMD_POWER_AP
#undef CONFIG_CMD_POWERINDEBUG
#undef CONFIG_CMD_SHMEM
#undef CONFIG_EXTPOWER
#undef CONFIG_KEYBOARD_KSO_BASE
#undef CONFIG_FLASH
#undef CONFIG_FMAP
#undef CONFIG_SWITCH
/* Modules we want to exclude */
#undef CONFIG_CMD_HASH
#undef CONFIG_CMD_TEMP_SENSOR
#undef CONFIG_ADC
#undef CONFIG_SHA256
/* power management definitions */
#define CONFIG_LOW_POWER_IDLE
#define CONFIG_ISH_PM_D0I1
#define CONFIG_ISH_PM_D0I2
#define CONFIG_ISH_PM_D0I3
#define CONFIG_ISH_PM_D3
#define CONFIG_ISH_PM_RESET_PREP
#define CONFIG_ISH_D0I2_MIN_USEC (15*MSEC) /* need final tune */
#define CONFIG_ISH_D0I3_MIN_USEC (100*MSEC) /* need final tune */
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
/* Motion sensors
*
* Note: Since we aren't using LPC memory map to transmit sensor data, the
* order of this enum does not need to be accel, accel, gyro
*/
enum sensor_id {
LID_ACCEL,
LID_GYRO,
BASE_ACCEL,
LID_MAG,
SENSOR_COUNT
};
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */