GNUBoot
/
coreboot-libre-fam15h-rdimm
2
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
coreboot-libre-fam15h-rdimm/3rdparty/chromeec/common/usb_pd_protocol.c

5735 lines
157 KiB
C
Raw Normal View History

Initial commit
2024-03-04 11:14:53 +01:00
/* Copyright 2014 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
#include "atomic.h"
#include "battery.h"
#include "battery_smart.h"
#include "board.h"
#include "charge_manager.h"
#include "charge_state.h"
#include "chipset.h"
#include "common.h"
#include "console.h"
#include "ec_commands.h"
#include "gpio.h"
#include "hooks.h"
#include "host_command.h"
#include "registers.h"
#include "system.h"
#include "task.h"
#include "timer.h"
#include "util.h"
#include "usb_charge.h"
#include "usb_common.h"
#include "usb_mux.h"
#include "usb_pd.h"
#include "usb_pd_tcpm.h"
#include "usb_pd_tcpc.h"
#include "usbc_ppc.h"
#include "tcpm.h"
#include "version.h"
#include "vboot.h"
#ifdef CONFIG_COMMON_RUNTIME
#define CPRINTF(format, args...) cprintf(CC_USBPD, format, ## args)
#define CPRINTS(format, args...) cprints(CC_USBPD, format, ## args)
BUILD_ASSERT(CONFIG_USB_PD_PORT_COUNT <= EC_USB_PD_MAX_PORTS);
/*
* If we are trying to upgrade the TCPC port that is supplying power, then we
* need to ensure that the battery has enough charge for the upgrade. 100mAh
* is about 5% of most batteries, and it should be enough charge to get us
* through the EC jump to RW and PD upgrade.
*/
#define MIN_BATTERY_FOR_TCPC_UPGRADE_MAH 100 /* mAH */
/*
* Debug log level - higher number == more log
* Level 0: Log state transitions
* Level 1: Level 0, plus state name
* Level 2: Level 1, plus packet info
* Level 3: Level 2, plus ping packet and packet dump on error
*
* Note that higher log level causes timing changes and thus may affect
* performance.
*
* Can be limited to constant debug_level by CONFIG_USB_PD_DEBUG_LEVEL
*/
#ifdef CONFIG_USB_PD_DEBUG_LEVEL
static const int debug_level = CONFIG_USB_PD_DEBUG_LEVEL;
#else
static int debug_level;
#endif
/*
* PD communication enabled flag. When false, PD state machine still
* detects source/sink connection and disconnection, and will still
* provide VBUS, but never sends any PD communication.
*/
static uint8_t pd_comm_enabled[CONFIG_USB_PD_PORT_COUNT];
#else /* CONFIG_COMMON_RUNTIME */
#define CPRINTF(format, args...)
#define CPRINTS(format, args...)
static const int debug_level;
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE
#define DUAL_ROLE_IF_ELSE(port, sink_clause, src_clause) \
(pd[port].power_role == PD_ROLE_SINK ? (sink_clause) : (src_clause))
#else
#define DUAL_ROLE_IF_ELSE(port, sink_clause, src_clause) (src_clause)
#endif
#define READY_RETURN_STATE(port) DUAL_ROLE_IF_ELSE(port, PD_STATE_SNK_READY, \
PD_STATE_SRC_READY)
/* Type C supply voltage (mV) */
#define TYPE_C_VOLTAGE 5000 /* mV */
/* PD counter definitions */
#define PD_MESSAGE_ID_COUNT 7
#define PD_HARD_RESET_COUNT 2
#define PD_CAPS_COUNT 50
#define PD_SNK_CAP_RETRIES 3
/*
* The time that we allow the port partner to send any messages after an
* explicit contract is established. 200ms was chosen somewhat arbitrarily as
* it should be long enough for sources to decide to send a message if they were
* going to, but not so long that a "low power charger connected" notification
* would be shown in the chrome OS UI.
*/
#define READY_HOLD_OFF_US (200 * MSEC)
enum vdm_states {
VDM_STATE_ERR_BUSY = -3,
VDM_STATE_ERR_SEND = -2,
VDM_STATE_ERR_TMOUT = -1,
VDM_STATE_DONE = 0,
/* Anything >0 represents an active state */
VDM_STATE_READY = 1,
VDM_STATE_BUSY = 2,
VDM_STATE_WAIT_RSP_BUSY = 3,
};
#ifdef CONFIG_USB_PD_DUAL_ROLE
/* Port dual-role state */
enum pd_dual_role_states drp_state[CONFIG_USB_PD_PORT_COUNT] = {
[0 ... (CONFIG_USB_PD_PORT_COUNT - 1)] =
CONFIG_USB_PD_INITIAL_DRP_STATE};
/* Enable variable for Try.SRC states */
static uint8_t pd_try_src_enable;
#endif
#ifdef CONFIG_USB_PD_REV30
/*
* The spec. revision is used to index into this array.
* Rev 0 (PD 1.0) - return PD_CTRL_REJECT
* Rev 1 (PD 2.0) - return PD_CTRL_REJECT
* Rev 2 (PD 3.0) - return PD_CTRL_NOT_SUPPORTED
*/
static const uint8_t refuse[] = {
PD_CTRL_REJECT, PD_CTRL_REJECT, PD_CTRL_NOT_SUPPORTED};
#define REFUSE(r) refuse[r]
#else
#define REFUSE(r) PD_CTRL_REJECT
#endif
#ifdef CONFIG_USB_PD_REV30
/*
* The spec. revision is used to index into this array.
* Rev 0 (VDO 1.0) - return VDM_VER10
* Rev 1 (VDO 1.0) - return VDM_VER10
* Rev 2 (VDO 2.0) - return VDM_VER20
*/
static const uint8_t vdo_ver[] = {
VDM_VER10, VDM_VER10, VDM_VER20};
#define VDO_VER(v) vdo_ver[v]
#else
#define VDO_VER(v) VDM_VER10
#endif
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
/* Tracker for which task is waiting on sysjump prep to finish */
static volatile task_id_t sysjump_task_waiting = TASK_ID_INVALID;
#endif
static struct pd_protocol {
/* current port power role (SOURCE or SINK) */
uint8_t power_role;
/* current port data role (DFP or UFP) */
uint8_t data_role;
/* 3-bit rolling message ID counter */
uint8_t msg_id;
/* Port polarity : 0 => CC1 is CC line, 1 => CC2 is CC line */
uint8_t polarity;
/* PD state for port */
enum pd_states task_state;
/* PD state when we run state handler the last time */
enum pd_states last_state;
/* bool: request state change to SUSPENDED */
uint8_t req_suspend_state;
/* The state to go to after timeout */
enum pd_states timeout_state;
/* port flags, see PD_FLAGS_* */
uint32_t flags;
/* Timeout for the current state. Set to 0 for no timeout. */
uint64_t timeout;
/* Time for source recovery after hard reset */
uint64_t src_recover;
/* Time for CC debounce end */
uint64_t cc_debounce;
/* The cc state */
enum pd_cc_states cc_state;
/* status of last transmit */
uint8_t tx_status;
/* Last received */
uint8_t last_msg_id;
/* last requested voltage PDO index */
int requested_idx;
#ifdef CONFIG_USB_PD_DUAL_ROLE
/* Current limit / voltage based on the last request message */
uint32_t curr_limit;
uint32_t supply_voltage;
/* Signal charging update that affects the port */
int new_power_request;
/* Store previously requested voltage request */
int prev_request_mv;
/* Time for Try.SRC states */
uint64_t try_src_marker;
uint64_t try_timeout;
#endif
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/* Time to enter low power mode */
uint64_t low_power_time;
/* Tasks to notify after TCPC has been reset */
int tasks_waiting_on_reset;
/* Tasks preventing TCPC from entering low power mode */
int tasks_preventing_lpm;
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
/*
* Timer for handling TOGGLE_OFF/FORCE_SINK mode when auto-toggle
* enabled. See drp_auto_toggle_next_state() for details.
*/
uint64_t drp_sink_time;
#endif
/*
* Time to ignore Vbus absence due to external IC debounce detection
* logic immediately after a power role swap.
*/
uint64_t vbus_debounce_time;
/* PD state for Vendor Defined Messages */
enum vdm_states vdm_state;
/* Timeout for the current vdm state. Set to 0 for no timeout. */
timestamp_t vdm_timeout;
/* next Vendor Defined Message to send */
uint32_t vdo_data[VDO_MAX_SIZE];
uint8_t vdo_count;
/* VDO to retry if UFP responder replied busy. */
uint32_t vdo_retry;
/* Attached ChromeOS device id, RW hash, and current RO / RW image */
uint16_t dev_id;
uint32_t dev_rw_hash[PD_RW_HASH_SIZE/4];
enum ec_current_image current_image;
#ifdef CONFIG_USB_PD_REV30
/* PD Collision avoidance buffer */
uint16_t ca_buffered;
uint16_t ca_header;
uint32_t ca_buffer[PDO_MAX_OBJECTS];
enum tcpm_transmit_type ca_type;
/* protocol revision */
uint8_t rev;
#endif
/*
* Some port partners are really chatty after an explicit contract is
* established. Therefore, we allow this time for the port partner to
* send any messages in order to avoid a collision of sending messages
* of our own.
*/
uint64_t ready_state_holdoff_timer;
} pd[CONFIG_USB_PD_PORT_COUNT];
#ifdef CONFIG_COMMON_RUNTIME
static const char * const pd_state_names[] = {
"DISABLED", "SUSPENDED",
"SNK_DISCONNECTED", "SNK_DISCONNECTED_DEBOUNCE",
"SNK_HARD_RESET_RECOVER",
"SNK_DISCOVERY", "SNK_REQUESTED", "SNK_TRANSITION", "SNK_READY",
"SNK_SWAP_INIT", "SNK_SWAP_SNK_DISABLE",
"SNK_SWAP_SRC_DISABLE", "SNK_SWAP_STANDBY", "SNK_SWAP_COMPLETE",
"SRC_DISCONNECTED", "SRC_DISCONNECTED_DEBOUNCE",
"SRC_HARD_RESET_RECOVER", "SRC_STARTUP",
"SRC_DISCOVERY", "SRC_NEGOCIATE", "SRC_ACCEPTED", "SRC_POWERED",
"SRC_TRANSITION", "SRC_READY", "SRC_GET_SNK_CAP", "DR_SWAP",
"SRC_SWAP_INIT", "SRC_SWAP_SNK_DISABLE", "SRC_SWAP_SRC_DISABLE",
"SRC_SWAP_STANDBY",
"VCONN_SWAP_SEND", "VCONN_SWAP_INIT", "VCONN_SWAP_READY",
"SOFT_RESET", "HARD_RESET_SEND", "HARD_RESET_EXECUTE", "BIST_RX",
"BIST_TX",
"DRP_AUTO_TOGGLE",
};
BUILD_ASSERT(ARRAY_SIZE(pd_state_names) == PD_STATE_COUNT);
#endif
/*
* 4 entry rw_hash table of type-C devices that AP has firmware updates for.
*/
#ifdef CONFIG_COMMON_RUNTIME
#define RW_HASH_ENTRIES 4
static struct ec_params_usb_pd_rw_hash_entry rw_hash_table[RW_HASH_ENTRIES];
#endif
int pd_comm_is_enabled(int port)
{
#ifdef CONFIG_COMMON_RUNTIME
return pd_comm_enabled[port];
#else
return 1;
#endif
}
static inline void set_state_timeout(int port,
uint64_t timeout,
enum pd_states timeout_state)
{
pd[port].timeout = timeout;
pd[port].timeout_state = timeout_state;
}
#ifdef CONFIG_USB_PD_REV30
int pd_get_rev(int port)
{
return pd[port].rev;
}
int pd_get_vdo_ver(int port)
{
return vdo_ver[pd[port].rev];
}
#endif
/* Return flag for pd state is connected */
int pd_is_connected(int port)
{
if (pd[port].task_state == PD_STATE_DISABLED)
return 0;
#ifdef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
if (pd[port].task_state == PD_STATE_DRP_AUTO_TOGGLE)
return 0;
#endif
return DUAL_ROLE_IF_ELSE(port,
/* sink */
pd[port].task_state != PD_STATE_SNK_DISCONNECTED &&
pd[port].task_state != PD_STATE_SNK_DISCONNECTED_DEBOUNCE,
/* source */
pd[port].task_state != PD_STATE_SRC_DISCONNECTED &&
pd[port].task_state != PD_STATE_SRC_DISCONNECTED_DEBOUNCE);
}
/*
* Return true if partner port is a DTS or TS capable of entering debug
* mode (eg. is presenting Rp/Rp or Rd/Rd).
*/
int pd_ts_dts_plugged(int port)
{
return pd[port].flags & PD_FLAGS_TS_DTS_PARTNER;
}
/* Return true if partner port is known to be PD capable. */
int pd_capable(int port)
{
return pd[port].flags & PD_FLAGS_PREVIOUS_PD_CONN;
}
/*
* Return true if partner port is capable of communication over USB data
* lines.
*/
int pd_get_partner_usb_comm_capable(int port)
{
return pd[port].flags & PD_FLAGS_PARTNER_USB_COMM;
}
#ifdef CONFIG_USB_PD_DUAL_ROLE
void pd_vbus_low(int port)
{
pd[port].flags &= ~PD_FLAGS_VBUS_NEVER_LOW;
}
#endif
int pd_is_vbus_present(int port)
{
#ifdef CONFIG_USB_PD_VBUS_DETECT_TCPC
return tcpm_get_vbus_level(port);
#else
return pd_snk_is_vbus_provided(port);
#endif
}
#ifdef CONFIG_USB_PD_RETIMER
int pd_is_ufp(int port)
{
return pd[port].cc_state == PD_CC_UFP_ATTACHED;
}
int pd_is_debug_acc(int port)
{
return pd[port].cc_state == PD_CC_UFP_DEBUG_ACC ||
pd[port].cc_state == PD_CC_DFP_DEBUG_ACC;
}
#endif
static void set_polarity(int port, int polarity)
{
tcpm_set_polarity(port, polarity);
#ifdef CONFIG_USBC_PPC_POLARITY
ppc_set_polarity(port, polarity);
#endif /* defined(CONFIG_USBC_PPC_POLARITY) */
}
#ifdef CONFIG_USBC_VCONN
static void set_vconn(int port, int enable)
{
/*
* We always need to tell the TCPC to enable Vconn first, otherwise some
* TCPCs get confused when a PPC sets secondary CC line to 5V and TCPC
* immediately disconnect. If there is a PPC, both devices will
* potentially source Vconn, but that should be okay since Vconn has
* "make before break" electrical requirements when swapping anyway.
*/
tcpm_set_vconn(port, enable);
#ifdef CONFIG_USBC_PPC_VCONN
ppc_set_vconn(port, enable);
#endif
}
#endif /* defined(CONFIG_USBC_VCONN) */
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/* 10 ms is enough time for any TCPC transaction to complete. */
#define PD_LPM_DEBOUNCE_US (10 * MSEC)
/* This is only called from the PD tasks that owns the port. */
static void handle_device_access(int port)
{
/* This should only be called from the PD task */
assert(port == TASK_ID_TO_PD_PORT(task_get_current()));
pd[port].low_power_time = get_time().val + PD_LPM_DEBOUNCE_US;
if (pd[port].flags & PD_FLAGS_LPM_ENGAGED) {
CPRINTS("TCPC p%d Exit Low Power Mode", port);
pd[port].flags &= ~(PD_FLAGS_LPM_ENGAGED |
PD_FLAGS_LPM_REQUESTED);
/*
* Wake to ensure we make another pass through the main task
* loop after clearing the flags.
*/
task_wake(PD_PORT_TO_TASK_ID(port));
}
}
static int pd_device_in_low_power(int port)
{
/*
* If we are actively waking the device up in the PD task, do not
* let TCPC operation wait or retry because we are in low power mode.
*/
if (port == TASK_ID_TO_PD_PORT(task_get_current()) &&
(pd[port].flags & PD_FLAGS_LPM_TRANSITION))
return 0;
return pd[port].flags & PD_FLAGS_LPM_ENGAGED;
}
static int reset_device_and_notify(int port)
{
int rv;
int task, waiting_tasks;
/* This should only be called from the PD task */
assert(port == TASK_ID_TO_PD_PORT(task_get_current()));
pd[port].flags |= PD_FLAGS_LPM_TRANSITION;
rv = tcpm_init(port);
pd[port].flags &= ~PD_FLAGS_LPM_TRANSITION;
if (rv == EC_SUCCESS)
CPRINTS("TCPC p%d init ready", port);
else
CPRINTS("TCPC p%d init failed!", port);
/*
* Before getting the other tasks that are waiting, clear the reset
* event from this PD task to prevent multiple reset/init events
* occurring.
*
* The double reset event happens when the higher priority PD interrupt
* task gets an interrupt during the above tcpm_init function. When that
* occurs, the higher priority task waits correctly for us to finish
* waking the TCPC, but it has also set PD_EVENT_TCPC_RESET again, which
* would result in a second, unnecessary init.
*/
atomic_clear(task_get_event_bitmap(task_get_current()),
PD_EVENT_TCPC_RESET);
waiting_tasks = atomic_read_clear(&pd[port].tasks_waiting_on_reset);
/*
* Now that we are done waking up the device, handle device access
* manually because we ignored it while waking up device.
*/
handle_device_access(port);
/* Clear SW LPM state; the state machine will set it again if needed */
pd[port].flags &= ~PD_FLAGS_LPM_REQUESTED;
/* Wake up all waiting tasks. */
while (waiting_tasks) {
task = __fls(waiting_tasks);
waiting_tasks &= ~BIT(task);
task_set_event(task, TASK_EVENT_PD_AWAKE, 0);
}
return rv;
}
static void pd_wait_for_wakeup(int port)
{
if (port == TASK_ID_TO_PD_PORT(task_get_current())) {
/* If we are in the PD task, we can directly reset */
reset_device_and_notify(port);
} else {
/* Otherwise, we need to wait for the TCPC reset to complete */
atomic_or(&pd[port].tasks_waiting_on_reset,
1 << task_get_current());
/*
* NOTE: We could be sending the PD task the reset event while
* it is already processing the reset event. If that occurs,
* then we will reset the TCPC multiple times, which is
* undesirable but most likely benign. Empirically, this doesn't
* happen much, but it if starts occurring, we can add a guard
* to prevent/reduce it.
*/
task_set_event(PD_PORT_TO_TASK_ID(port),
PD_EVENT_TCPC_RESET, 0);
task_wait_event_mask(TASK_EVENT_PD_AWAKE, -1);
}
}
void pd_wait_exit_low_power(int port)
{
if (pd_device_in_low_power(port))
pd_wait_for_wakeup(port);
}
/*
* This can be called from any task. If we are in the PD task, we can handle
* immediately. Otherwise, we need to notify the PD task via event.
*/
void pd_device_accessed(int port)
{
if (port == TASK_ID_TO_PD_PORT(task_get_current())) {
/* Ignore any access to device while it is waking up */
if (pd[port].flags & PD_FLAGS_LPM_TRANSITION)
return;
handle_device_access(port);
} else {
task_set_event(PD_PORT_TO_TASK_ID(port),
PD_EVENT_DEVICE_ACCESSED, 0);
}
}
void pd_prevent_low_power_mode(int port, int prevent)
{
const int current_task_mask = (1 << task_get_current());
if (prevent)
atomic_or(&pd[port].tasks_preventing_lpm, current_task_mask);
else
atomic_clear(&pd[port].tasks_preventing_lpm, current_task_mask);
}
/* This is only called from the PD tasks that owns the port. */
static void exit_low_power_mode(int port)
{
if (pd[port].flags & PD_FLAGS_LPM_ENGAGED)
reset_device_and_notify(port);
else
pd[port].flags &= ~PD_FLAGS_LPM_REQUESTED;
}
#else /* !CONFIG_USB_PD_TCPC_LOW_POWER */
/* We don't need to notify anyone if low power mode isn't involved. */
static int reset_device_and_notify(int port)
{
const int rv = tcpm_init(port);
if (rv == EC_SUCCESS)
CPRINTS("TCPC p%d init ready", port);
else
CPRINTS("TCPC p%d init failed!", port);
return rv;
}
#endif /* CONFIG_USB_PD_TCPC_LOW_POWER */
#ifdef CONFIG_USB_PD_DUAL_ROLE
static int get_bbram_idx(int port)
{
switch (port) {
case 2:
return SYSTEM_BBRAM_IDX_PD2;
case 1:
return SYSTEM_BBRAM_IDX_PD1;
case 0:
return SYSTEM_BBRAM_IDX_PD0;
default:
return -1;
}
}
static int pd_get_saved_port_flags(int port, uint8_t *flags)
{
if (system_get_bbram(get_bbram_idx(port), flags) != EC_SUCCESS) {
#ifndef CHIP_HOST
CPRINTS("PD NVRAM FAIL");
#endif
return EC_ERROR_UNKNOWN;
}
return EC_SUCCESS;
}
static void pd_set_saved_port_flags(int port, uint8_t flags)
{
if (system_set_bbram(get_bbram_idx(port), flags) != EC_SUCCESS) {
#ifndef CHIP_HOST
CPRINTS("PD NVRAM FAIL");
#endif
}
}
static void pd_update_saved_port_flags(int port, uint8_t flag, uint8_t val)
{
uint8_t saved_flags;
if (pd_get_saved_port_flags(port, &saved_flags) != EC_SUCCESS)
return;
if (val)
saved_flags |= flag;
else
saved_flags &= ~flag;
pd_set_saved_port_flags(port, saved_flags);
}
#endif /* defined(CONFIG_USB_PD_DUAL_ROLE) */
/**
* Invalidate last message received at the port when the port gets disconnected
* or reset(soft/hard). This is used to identify and handle the duplicate
* messages.
*
* @param port USB PD TCPC port number
*/
static void invalidate_last_message_id(int port)
{
/*
* Message id starts from 0 to 7. If last_msg_id is initialized to 0,
* it will lead to repetitive message id with first received packet,
* so initialize it with an invalid value 0xff.
*/
pd[port].last_msg_id = 0xff;
}
/**
* Identify and drop any duplicate messages received at the port.
*
* @param port USB PD TCPC port number
* @param msg_header Message Header containing the RX message ID
* @return 1 if the received message is a duplicate one, 0 otherwise.
*/
static int consume_repeat_message(int port, uint16_t msg_header)
{
uint8_t msg_id = PD_HEADER_ID(msg_header);
/* If repeat message ignore, except softreset control request. */
if (PD_HEADER_TYPE(msg_header) == PD_CTRL_SOFT_RESET &&
PD_HEADER_CNT(msg_header) == 0) {
return 0;
} else if (pd[port].last_msg_id != msg_id) {
pd[port].last_msg_id = msg_id;
} else if (pd[port].last_msg_id == msg_id) {
CPRINTF("C%d Repeat msg_id %d\n", port, msg_id);
return 1;
}
return 0;
}
/**
* Returns true if the port is currently in the try src state.
*/
static inline int is_try_src(int port)
{
return pd[port].flags & PD_FLAGS_TRY_SRC;
}
static inline void set_state(int port, enum pd_states next_state)
{
enum pd_states last_state = pd[port].task_state;
#ifdef CONFIG_LOW_POWER_IDLE
int i;
#endif
set_state_timeout(port, 0, 0);
pd[port].task_state = next_state;
if (last_state == next_state)
return;
#if defined(CONFIG_USBC_PPC) && defined(CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE)
/* If we're entering DRP_AUTO_TOGGLE, there is no sink connected. */
if (next_state == PD_STATE_DRP_AUTO_TOGGLE) {
ppc_sink_is_connected(port, 0);
/*
* Clear the overcurrent event counter
* since we've detected a disconnect.
*/
ppc_clear_oc_event_counter(port);
}
#endif /* CONFIG_USBC_PPC && CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE */
#ifdef CONFIG_USB_PD_DUAL_ROLE
#ifdef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
/* Clear flag to allow DRP auto toggle when possible */
if (last_state != PD_STATE_DRP_AUTO_TOGGLE)
pd[port].flags &= ~PD_FLAGS_TCPC_DRP_TOGGLE;
#endif
/* Ignore dual-role toggling between sink and source */
if ((last_state == PD_STATE_SNK_DISCONNECTED &&
next_state == PD_STATE_SRC_DISCONNECTED) ||
(last_state == PD_STATE_SRC_DISCONNECTED &&
next_state == PD_STATE_SNK_DISCONNECTED))
return;
if (next_state == PD_STATE_SRC_DISCONNECTED ||
next_state == PD_STATE_SNK_DISCONNECTED) {
#ifdef CONFIG_USBC_PPC
enum tcpc_cc_voltage_status cc1, cc2;
tcpm_get_cc(port, &cc1, &cc2);
/*
* Neither a debug accessory nor UFP attached.
* Tell the PPC module that there is no sink connected.
*/
if (!cc_is_at_least_one_rd(cc1, cc2)) {
ppc_sink_is_connected(port, 0);
/*
* Clear the overcurrent event counter
* since we've detected a disconnect.
*/
ppc_clear_oc_event_counter(port);
}
#endif /* CONFIG_USBC_PPC */
/* Clear the holdoff timer since the port is disconnected. */
pd[port].ready_state_holdoff_timer = 0;
/*
* We should not clear any flags when transitioning back to the
* disconnected state from the debounce state as the two states
* here are really the same states in the state diagram.
*/
if (last_state != PD_STATE_SNK_DISCONNECTED_DEBOUNCE &&
last_state != PD_STATE_SRC_DISCONNECTED_DEBOUNCE) {
pd[port].flags &= ~PD_FLAGS_RESET_ON_DISCONNECT_MASK;
reset_pd_cable(port);
}
/* Clear the input current limit */
pd_set_input_current_limit(port, 0, 0);
#ifdef CONFIG_CHARGE_MANAGER
typec_set_input_current_limit(port, 0, 0);
charge_manager_set_ceil(port,
CEIL_REQUESTOR_PD,
CHARGE_CEIL_NONE);
#endif
#ifdef CONFIG_BC12_DETECT_DATA_ROLE_TRIGGER
/*
* When data role set events are used to enable BC1.2, then CC
* detach events are used to notify BC1.2 that it can be powered
* down.
*/
task_set_event(USB_CHG_PORT_TO_TASK_ID(port),
USB_CHG_EVENT_CC_OPEN, 0);
#endif /* CONFIG_BC12_DETECT_DATA_ROLE_TRIGGER */
#ifdef CONFIG_USBC_VCONN
set_vconn(port, 0);
#endif /* defined(CONFIG_USBC_VCONN) */
pd_update_saved_port_flags(port, PD_BBRMFLG_EXPLICIT_CONTRACT,
0);
#else /* CONFIG_USB_PD_DUAL_ROLE */
if (next_state == PD_STATE_SRC_DISCONNECTED) {
#ifdef CONFIG_USBC_VCONN
set_vconn(port, 0);
#endif /* CONFIG_USBC_VCONN */
#endif /* !CONFIG_USB_PD_DUAL_ROLE */
/* If we are source, make sure VBUS is off and restore RP */
if (pd[port].power_role == PD_ROLE_SOURCE) {
/* Restore non-active ports to CONFIG_USB_PD_PULLUP */
pd_power_supply_reset(port);
tcpm_set_cc(port, TYPEC_CC_RP);
}
#ifdef CONFIG_USB_PD_REV30
/* Adjust rev to highest level*/
pd[port].rev = PD_REV30;
#endif
pd[port].dev_id = 0;
#ifdef CONFIG_CHARGE_MANAGER
charge_manager_update_dualrole(port, CAP_UNKNOWN);
#endif
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
pd_dfp_exit_mode(port, 0, 0);
#endif
/*
* Indicate that the port is disconnected so the board
* can restore state from any previous data swap.
*/
pd_execute_data_swap(port, PD_ROLE_DISCONNECTED);
#ifdef CONFIG_USBC_SS_MUX
usb_mux_set(port, TYPEC_MUX_NONE, USB_SWITCH_DISCONNECT,
pd[port].polarity);
#endif
/* Disable TCPC RX */
tcpm_set_rx_enable(port, 0);
/* Invalidate message IDs. */
invalidate_last_message_id(port);
#ifdef CONFIG_COMMON_RUNTIME
/* detect USB PD cc disconnect */
hook_notify(HOOK_USB_PD_DISCONNECT);
#endif
}
#ifdef CONFIG_LOW_POWER_IDLE
/* If a PD device is attached then disable deep sleep */
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++) {
if (pd_capable(i))
break;
}
if (i == CONFIG_USB_PD_PORT_COUNT)
enable_sleep(SLEEP_MASK_USB_PD);
else
disable_sleep(SLEEP_MASK_USB_PD);
#endif
if (debug_level > 0)
CPRINTF("C%d st%d %s\n", port, next_state,
pd_state_names[next_state]);
else
CPRINTF("C%d st%d\n", port, next_state);
}
/* increment message ID counter */
static void inc_id(int port)
{
pd[port].msg_id = (pd[port].msg_id + 1) & PD_MESSAGE_ID_COUNT;
}
#ifdef CONFIG_USB_PD_REV30
static void sink_can_xmit(int port, int rp)
{
tcpm_select_rp_value(port, rp);
tcpm_set_cc(port, TYPEC_CC_RP);
}
static inline void pd_ca_reset(int port)
{
pd[port].ca_buffered = 0;
}
#endif
void pd_transmit_complete(int port, int status)
{
if (status == TCPC_TX_COMPLETE_SUCCESS)
inc_id(port);
pd[port].tx_status = status;
task_set_event(PD_PORT_TO_TASK_ID(port), PD_EVENT_TX, 0);
}
static int pd_transmit(int port, enum tcpm_transmit_type type,
uint16_t header, const uint32_t *data)
{
int evt;
/* If comms are disabled, do not transmit, return error */
if (!pd_comm_is_enabled(port))
return -1;
#ifdef CONFIG_USB_PD_REV30
/* Source-coordinated collision avoidance */
/*
* In order to avoid message collisions due to asynchronous Messaging
* sent from the Sink, the Source sets Rp to SinkTxOk to indicate to
* the Sink that it is ok to initiate an AMS. When the Source wishes
* to initiate an AMS it sets Rp to SinkTxNG. When the Sink detects
* that Rp is set to SinkTxOk it May initiate an AMS. When the Sink
* detects that Rp is set to SinkTxNG it Shall Not initiate an AMS
* and Shall only send Messages that are part of an AMS the Source has
* initiated. Note that this restriction applies to SOP* AMS’s i.e.
* for both Port to Port and Port to Cable Plug communications.
*
* This starts after an Explicit Contract is in place
* PD R3 V1.1 Section 2.5.2.
*
* Note: a Sink can still send Hard Reset signaling at any time.
*/
if ((pd[port].rev == PD_REV30) &&
(pd[port].flags & PD_FLAGS_EXPLICIT_CONTRACT)) {
if (pd[port].power_role == PD_ROLE_SOURCE) {
/*
* Inform Sink that it can't transmit. If a sink
* transmition is in progress and a collsion occurs,
* a reset is generated. This should be rare because
* all extended messages are chunked. This effectively
* defaults to PD REV 2.0 collision avoidance.
*/
sink_can_xmit(port, SINK_TX_NG);
} else if (type != TCPC_TX_HARD_RESET) {
enum tcpc_cc_voltage_status cc1, cc2;
tcpm_get_cc(port, &cc1, &cc2);
if (cc1 == TYPEC_CC_VOLT_RP_1_5 ||
cc2 == TYPEC_CC_VOLT_RP_1_5) {
/* Sink can't transmit now. */
/* Check if message is already buffered. */
if (pd[port].ca_buffered)
return -1;
/* Buffer message and send later. */
pd[port].ca_type = type;
pd[port].ca_header = header;
memcpy(pd[port].ca_buffer,
data, sizeof(uint32_t) *
PD_HEADER_CNT(header));
pd[port].ca_buffered = 1;
return 1;
}
}
}
#endif
tcpm_transmit(port, type, header, data);
/* Wait until TX is complete */
evt = task_wait_event_mask(PD_EVENT_TX, PD_T_TCPC_TX_TIMEOUT);
#ifdef CONFIG_USB_PD_REV30
/*
* If the source just completed a transmit, tell
* the sink it can transmit if it wants to.
*/
if ((pd[port].rev == PD_REV30) &&
(pd[port].power_role == PD_ROLE_SOURCE) &&
(pd[port].flags & PD_FLAGS_EXPLICIT_CONTRACT)) {
sink_can_xmit(port, SINK_TX_OK);
}
#endif
if (evt & TASK_EVENT_TIMER)
return -1;
/* TODO: give different error condition for failed vs discarded */
return pd[port].tx_status == TCPC_TX_COMPLETE_SUCCESS ? 1 : -1;
}
#ifdef CONFIG_USB_PD_REV30
static void pd_ca_send_pending(int port)
{
enum tcpc_cc_voltage_status cc1, cc2;
/* Check if a message has been buffered. */
if (!pd[port].ca_buffered)
return;
tcpm_get_cc(port, &cc1, &cc2);
if ((cc1 != TYPEC_CC_VOLT_RP_1_5) &&
(cc2 != TYPEC_CC_VOLT_RP_1_5))
if (pd_transmit(port, pd[port].ca_type,
pd[port].ca_header,
pd[port].ca_buffer) < 0)
return;
/* Message was sent, so free up the buffer. */
pd[port].ca_buffered = 0;
}
#endif
static void pd_update_roles(int port)
{
/* Notify TCPC of role update */
tcpm_set_msg_header(port, pd[port].power_role, pd[port].data_role);
}
static int send_control(int port, int type)
{
int bit_len;
uint16_t header = PD_HEADER(type, pd[port].power_role,
pd[port].data_role, pd[port].msg_id, 0,
pd_get_rev(port), 0);
bit_len = pd_transmit(port, TCPC_TX_SOP, header, NULL);
if (debug_level >= 2)
CPRINTF("C%d CTRL[%d]>%d\n", port, type, bit_len);
return bit_len;
}
static int send_source_cap(int port)
{
int bit_len;
#if defined(CONFIG_USB_PD_DYNAMIC_SRC_CAP) || \
defined(CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT)
const uint32_t *src_pdo;
const int src_pdo_cnt = charge_manager_get_source_pdo(&src_pdo, port);
#else
const uint32_t *src_pdo = pd_src_pdo;
const int src_pdo_cnt = pd_src_pdo_cnt;
#endif
uint16_t header;
if (src_pdo_cnt == 0)
/* No source capabilities defined, sink only */
header = PD_HEADER(PD_CTRL_REJECT, pd[port].power_role,
pd[port].data_role, pd[port].msg_id, 0,
pd_get_rev(port), 0);
else
header = PD_HEADER(PD_DATA_SOURCE_CAP, pd[port].power_role,
pd[port].data_role, pd[port].msg_id, src_pdo_cnt,
pd_get_rev(port), 0);
bit_len = pd_transmit(port, TCPC_TX_SOP, header, src_pdo);
if (debug_level >= 2)
CPRINTF("C%d srcCAP>%d\n", port, bit_len);
return bit_len;
}
#ifdef CONFIG_USB_PD_REV30
static int send_battery_cap(int port, uint32_t *payload)
{
int bit_len;
uint16_t msg[6] = {0, 0, 0, 0, 0, 0};
uint16_t header = PD_HEADER(PD_EXT_BATTERY_CAP,
pd[port].power_role,
pd[port].data_role,
pd[port].msg_id,
3, /* Number of Data Objects */
pd[port].rev,
1 /* This is an exteded message */
);
/* Set extended header */
msg[0] = PD_EXT_HEADER(0, /* Chunk Number */
0, /* Request Chunk */
9 /* Data Size in bytes */
);
/* Set VID */
msg[1] = USB_VID_GOOGLE;
/* Set PID */
msg[2] = CONFIG_USB_PID;
if (battery_is_present()) {
/*
* We only have one fixed battery,
* so make sure batt cap ref is 0.
*/
if (BATT_CAP_REF(payload[0]) != 0) {
/* Invalid battery reference */
msg[5] = 1;
} else {
uint32_t v;
uint32_t c;
/*
* The Battery Design Capacity field shall return the
* Battery’s design capacity in tenths of Wh. If the
* Battery is Hot Swappable and is not present, the
* Battery Design Capacity field shall be set to 0. If
* the Battery is unable to report its Design Capacity,
* it shall return 0xFFFF
*/
msg[3] = 0xffff;
/*
* The Battery Last Full Charge Capacity field shall
* return the Battery’s last full charge capacity in
* tenths of Wh. If the Battery is Hot Swappable and
* is not present, the Battery Last Full Charge Capacity
* field shall be set to 0. If the Battery is unable to
* report its Design Capacity, the Battery Last Full
* Charge Capacity field shall be set to 0xFFFF.
*/
msg[4] = 0xffff;
if (battery_design_voltage(&v) == 0) {
if (battery_design_capacity(&c) == 0) {
/*
* Wh = (c * v) / 1000000
* 10th of a Wh = Wh * 10
*/
msg[3] = DIV_ROUND_NEAREST((c * v),
100000);
}
if (battery_full_charge_capacity(&c) == 0) {
/*
* Wh = (c * v) / 1000000
* 10th of a Wh = Wh * 10
*/
msg[4] = DIV_ROUND_NEAREST((c * v),
100000);
}
}
}
}
bit_len = pd_transmit(port, TCPC_TX_SOP, header, (uint32_t *)msg);
if (debug_level >= 2)
CPRINTF("C%d batCap>%d\n", port, bit_len);
return bit_len;
}
static int send_battery_status(int port, uint32_t *payload)
{
int bit_len;
uint32_t msg = 0;
uint16_t header = PD_HEADER(PD_DATA_BATTERY_STATUS,
pd[port].power_role,
pd[port].data_role,
pd[port].msg_id,
1, /* Number of Data Objects */
pd[port].rev,
0 /* This is NOT an extended message */
);
if (battery_is_present()) {
/*
* We only have one fixed battery,
* so make sure batt cap ref is 0.
*/
if (BATT_CAP_REF(payload[0]) != 0) {
/* Invalid battery reference */
msg |= BSDO_INVALID;
} else {
uint32_t v;
uint32_t c;
if (battery_design_voltage(&v) != 0 ||
battery_remaining_capacity(&c) != 0) {
msg |= BSDO_CAP(BSDO_CAP_UNKNOWN);
} else {
/*
* Wh = (c * v) / 1000000
* 10th of a Wh = Wh * 10
*/
msg |= BSDO_CAP(DIV_ROUND_NEAREST((c * v),
100000));
}
/* Battery is present */
msg |= BSDO_PRESENT;
/*
* For drivers that are not smart battery compliant,
* battery_status() returns EC_ERROR_UNIMPLEMENTED and
* the battery is assumed to be idle.
*/
if (battery_status(&c) != 0) {
msg |= BSDO_IDLE; /* assume idle */
} else {
if (c & STATUS_FULLY_CHARGED)
/* Fully charged */
msg |= BSDO_IDLE;
else if (c & STATUS_DISCHARGING)
/* Discharging */
msg |= BSDO_DISCHARGING;
/* else battery is charging.*/
}
}
} else {
msg = BSDO_CAP(BSDO_CAP_UNKNOWN);
}
bit_len = pd_transmit(port, TCPC_TX_SOP, header, &msg);
if (debug_level >= 2)
CPRINTF("C%d batStat>%d\n", port, bit_len);
return bit_len;
}
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE
static void send_sink_cap(int port)
{
int bit_len;
uint16_t header = PD_HEADER(PD_DATA_SINK_CAP, pd[port].power_role,
pd[port].data_role, pd[port].msg_id, pd_snk_pdo_cnt,
pd_get_rev(port), 0);
bit_len = pd_transmit(port, TCPC_TX_SOP, header, pd_snk_pdo);
if (debug_level >= 2)
CPRINTF("C%d snkCAP>%d\n", port, bit_len);
}
static int send_request(int port, uint32_t rdo)
{
int bit_len;
uint16_t header = PD_HEADER(PD_DATA_REQUEST, pd[port].power_role,
pd[port].data_role, pd[port].msg_id, 1,
pd_get_rev(port), 0);
bit_len = pd_transmit(port, TCPC_TX_SOP, header, &rdo);
if (debug_level >= 2)
CPRINTF("C%d REQ>%d\n", port, bit_len);
return bit_len;
}
#endif /* CONFIG_USB_PD_DUAL_ROLE */
#ifdef CONFIG_COMMON_RUNTIME
static int send_bist_cmd(int port)
{
/* currently only support sending bist carrier 2 */
uint32_t bdo = BDO(BDO_MODE_CARRIER2, 0);
int bit_len;
uint16_t header = PD_HEADER(PD_DATA_BIST, pd[port].power_role,
pd[port].data_role, pd[port].msg_id, 1,
pd_get_rev(port), 0);
bit_len = pd_transmit(port, TCPC_TX_SOP, header, &bdo);
CPRINTF("C%d BIST>%d\n", port, bit_len);
return bit_len;
}
#endif
static void queue_vdm(int port, uint32_t *header, const uint32_t *data,
int data_cnt)
{
pd[port].vdo_count = data_cnt + 1;
pd[port].vdo_data[0] = header[0];
memcpy(&pd[port].vdo_data[1], data, sizeof(uint32_t) * data_cnt);
/* Set ready, pd task will actually send */
pd[port].vdm_state = VDM_STATE_READY;
}
static void handle_vdm_request(int port, int cnt, uint32_t *payload)
{
int rlen = 0;
uint32_t *rdata;
if (pd[port].vdm_state == VDM_STATE_BUSY) {
/* If UFP responded busy retry after timeout */
if (PD_VDO_CMDT(payload[0]) == CMDT_RSP_BUSY) {
pd[port].vdm_timeout.val = get_time().val +
PD_T_VDM_BUSY;
pd[port].vdm_state = VDM_STATE_WAIT_RSP_BUSY;
pd[port].vdo_retry = (payload[0] & ~VDO_CMDT_MASK) |
CMDT_INIT;
return;
} else {
pd[port].vdm_state = VDM_STATE_DONE;
}
}
if (PD_VDO_SVDM(payload[0]))
rlen = pd_svdm(port, cnt, payload, &rdata);
else
rlen = pd_custom_vdm(port, cnt, payload, &rdata);
if (rlen > 0) {
queue_vdm(port, rdata, &rdata[1], rlen - 1);
return;
}
if (debug_level >= 2)
CPRINTF("C%d Unhandled VDM VID %04x CMD %04x\n",
port, PD_VDO_VID(payload[0]), payload[0] & 0xFFFF);
}
static __maybe_unused int pd_is_disconnected(int port)
{
return pd[port].task_state == PD_STATE_SRC_DISCONNECTED
#ifdef CONFIG_USB_PD_DUAL_ROLE
|| pd[port].task_state == PD_STATE_SNK_DISCONNECTED
#endif
;
}
static void set_usb_mux_with_current_data_role(int port)
{
#ifdef CONFIG_USBC_SS_MUX
/*
* If the SoC is down, then we disconnect the MUX to save power since
* no one cares about the data lines.
*/
#ifdef CONFIG_POWER_COMMON
if (chipset_in_or_transitioning_to_state(CHIPSET_STATE_ANY_OFF)) {
usb_mux_set(port, TYPEC_MUX_NONE, USB_SWITCH_DISCONNECT,
pd[port].polarity);
return;
}
#endif /* CONFIG_POWER_COMMON */
/*
* When PD stack is disconnected, then mux should be disconnected, which
* is also what happens in the set_state disconnection code. Once the
* PD state machine progresses out of disconnect, the MUX state will
* be set correctly again.
*/
if (pd_is_disconnected(port))
usb_mux_set(port, TYPEC_MUX_NONE, USB_SWITCH_DISCONNECT,
pd[port].polarity);
/*
* If new data role isn't DFP and we only support DFP, also disconnect.
*/
else if (IS_ENABLED(CONFIG_USBC_SS_MUX_DFP_ONLY) &&
pd[port].data_role != PD_ROLE_DFP)
usb_mux_set(port, TYPEC_MUX_NONE, USB_SWITCH_DISCONNECT,
pd[port].polarity);
/*
* Otherwise connect mux since we are in S3+
*/
else
usb_mux_set(port, TYPEC_MUX_USB, USB_SWITCH_CONNECT,
pd[port].polarity);
#endif /* CONFIG_USBC_SS_MUX */
}
static void pd_set_data_role(int port, int role)
{
pd[port].data_role = role;
#ifdef CONFIG_USB_PD_DUAL_ROLE
pd_update_saved_port_flags(port, PD_BBRMFLG_DATA_ROLE, role);
#endif /* defined(CONFIG_USB_PD_DUAL_ROLE) */
pd_execute_data_swap(port, role);
set_usb_mux_with_current_data_role(port);
pd_update_roles(port);
#ifdef CONFIG_BC12_DETECT_DATA_ROLE_TRIGGER
/*
* For BC1.2 detection that is triggered on data role change events
* instead of VBUS changes, need to set an event to wake up the USB_CHG
* task and indicate the current data role.
*/
if (role == PD_ROLE_UFP)
task_set_event(USB_CHG_PORT_TO_TASK_ID(port),
USB_CHG_EVENT_DR_UFP, 0);
else if (role == PD_ROLE_DFP)
task_set_event(USB_CHG_PORT_TO_TASK_ID(port),
USB_CHG_EVENT_DR_DFP, 0);
#endif /* CONFIG_BC12_DETECT_DATA_ROLE_TRIGGER */
}
#ifdef CONFIG_USBC_VCONN
static void pd_set_vconn_role(int port, int role)
{
if (role == PD_ROLE_VCONN_ON)
pd[port].flags |= PD_FLAGS_VCONN_ON;
else
pd[port].flags &= ~PD_FLAGS_VCONN_ON;
#ifdef CONFIG_USB_PD_DUAL_ROLE
pd_update_saved_port_flags(port, PD_BBRMFLG_VCONN_ROLE, role);
#endif
}
#endif /* CONFIG_USBC_VCONN */
void pd_execute_hard_reset(int port)
{
int hard_rst_tx = pd[port].last_state == PD_STATE_HARD_RESET_SEND;
CPRINTF("C%d HARD RST %cX\n", port, hard_rst_tx ? 'T' : 'R');
pd[port].msg_id = 0;
invalidate_last_message_id(port);
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
pd_dfp_exit_mode(port, 0, 0);
#endif
#ifdef CONFIG_USB_PD_REV30
pd[port].rev = PD_REV30;
pd_ca_reset(port);
#endif
/*
* Fake set last state to hard reset to make sure that the next
* state to run knows that we just did a hard reset.
*/
pd[port].last_state = PD_STATE_HARD_RESET_EXECUTE;
#ifdef CONFIG_USB_PD_DUAL_ROLE
/*
* If we are swapping to a source and have changed to Rp, restore back
* to Rd and turn off vbus to match our power_role.
*/
if (pd[port].task_state == PD_STATE_SNK_SWAP_STANDBY ||
pd[port].task_state == PD_STATE_SNK_SWAP_COMPLETE) {
tcpm_set_cc(port, TYPEC_CC_RD);
pd_power_supply_reset(port);
}
/* Set initial data role (matching power role) */
pd_set_data_role(port, pd[port].power_role);
if (pd[port].power_role == PD_ROLE_SINK) {
/* Clear the input current limit */
pd_set_input_current_limit(port, 0, 0);
#ifdef CONFIG_CHARGE_MANAGER
charge_manager_set_ceil(port,
CEIL_REQUESTOR_PD,
CHARGE_CEIL_NONE);
#endif /* CONFIG_CHARGE_MANAGER */
#ifdef CONFIG_USBC_VCONN
/*
* Sink must turn off Vconn after a hard reset if it was being
* sourced previously
*/
if (pd[port].flags & PD_FLAGS_VCONN_ON) {
set_vconn(port, 0);
pd_set_vconn_role(port, PD_ROLE_VCONN_OFF);
}
#endif
set_state(port, PD_STATE_SNK_HARD_RESET_RECOVER);
return;
}
#endif /* CONFIG_USB_PD_DUAL_ROLE */
if (!hard_rst_tx)
usleep(PD_T_PS_HARD_RESET);
/* We are a source, cut power */
pd_power_supply_reset(port);
pd[port].src_recover = get_time().val + PD_T_SRC_RECOVER;
#ifdef CONFIG_USBC_VCONN
set_vconn(port, 0);
#endif
set_state(port, PD_STATE_SRC_HARD_RESET_RECOVER);
}
static void execute_soft_reset(int port)
{
pd[port].msg_id = 0;
invalidate_last_message_id(port);
set_state(port, DUAL_ROLE_IF_ELSE(port, PD_STATE_SNK_DISCOVERY,
PD_STATE_SRC_DISCOVERY));
CPRINTF("C%d Soft Rst\n", port);
}
void pd_soft_reset(void)
{
int i;
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; ++i)
if (pd_is_connected(i)) {
set_state(i, PD_STATE_SOFT_RESET);
task_wake(PD_PORT_TO_TASK_ID(i));
}
}
#ifdef CONFIG_USB_PD_DUAL_ROLE
/*
* Request desired charge voltage from source.
* Returns EC_SUCCESS on success or non-zero on failure.
*/
static int pd_send_request_msg(int port, int always_send_request)
{
uint32_t rdo, curr_limit, supply_voltage;
int res;
#ifdef CONFIG_CHARGE_MANAGER
int charging = (charge_manager_get_active_charge_port() == port);
#else
const int charging = 1;
#endif
#ifdef CONFIG_USB_PD_CHECK_MAX_REQUEST_ALLOWED
int max_request_allowed = pd_is_max_request_allowed();
#else
const int max_request_allowed = 1;
#endif
/* Clear new power request */
pd[port].new_power_request = 0;
/* Build and send request RDO */
/*
* If this port is not actively charging or we are not allowed to
* request the max voltage, then select vSafe5V
*/
pd_build_request(pd_get_src_cap_cnt(port), pd_get_src_caps(port), 0,
&rdo, &curr_limit, &supply_voltage,
charging && max_request_allowed ?
PD_REQUEST_MAX : PD_REQUEST_VSAFE5V,
get_max_request_mv());
if (!always_send_request) {
/* Don't re-request the same voltage */
if (pd[port].prev_request_mv == supply_voltage)
return EC_SUCCESS;
#ifdef CONFIG_CHARGE_MANAGER
/* Limit current to PD_MIN_MA during transition */
else
charge_manager_force_ceil(port, PD_MIN_MA);
#endif
}
CPRINTF("C%d Req [%d] %dmV %dmA", port, RDO_POS(rdo),
supply_voltage, curr_limit);
if (rdo & RDO_CAP_MISMATCH)
CPRINTF(" Mismatch");
CPRINTF("\n");
pd[port].curr_limit = curr_limit;
pd[port].supply_voltage = supply_voltage;
pd[port].prev_request_mv = supply_voltage;
res = send_request(port, rdo);
if (res < 0)
return res;
set_state(port, PD_STATE_SNK_REQUESTED);
return EC_SUCCESS;
}
#endif
static void pd_update_pdo_flags(int port, uint32_t pdo)
{
#ifdef CONFIG_CHARGE_MANAGER
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
int charge_whitelisted =
(pd[port].power_role == PD_ROLE_SINK &&
pd_charge_from_device(pd_get_identity_vid(port),
pd_get_identity_pid(port)));
#else
const int charge_whitelisted = 0;
#endif
#endif
/* can only parse PDO flags if type is fixed */
if ((pdo & PDO_TYPE_MASK) != PDO_TYPE_FIXED)
return;
#ifdef CONFIG_USB_PD_DUAL_ROLE
if (pdo & PDO_FIXED_DUAL_ROLE)
pd[port].flags |= PD_FLAGS_PARTNER_DR_POWER;
else
pd[port].flags &= ~PD_FLAGS_PARTNER_DR_POWER;
if (pdo & PDO_FIXED_EXTERNAL)
pd[port].flags |= PD_FLAGS_PARTNER_EXTPOWER;
else
pd[port].flags &= ~PD_FLAGS_PARTNER_EXTPOWER;
if (pdo & PDO_FIXED_COMM_CAP)
pd[port].flags |= PD_FLAGS_PARTNER_USB_COMM;
else
pd[port].flags &= ~PD_FLAGS_PARTNER_USB_COMM;
#endif
if (pdo & PDO_FIXED_DATA_SWAP)
pd[port].flags |= PD_FLAGS_PARTNER_DR_DATA;
else
pd[port].flags &= ~PD_FLAGS_PARTNER_DR_DATA;
#ifdef CONFIG_CHARGE_MANAGER
/*
* Treat device as a dedicated charger (meaning we should charge
* from it) if it does not support power swap, or if it is externally
* powered, or if we are a sink and the device identity matches a
* charging white-list.
*/
if (!(pd[port].flags & PD_FLAGS_PARTNER_DR_POWER) ||
(pd[port].flags & PD_FLAGS_PARTNER_EXTPOWER) ||
charge_whitelisted)
charge_manager_update_dualrole(port, CAP_DEDICATED);
else
charge_manager_update_dualrole(port, CAP_DUALROLE);
#endif
}
static void handle_data_request(int port, uint16_t head,
uint32_t *payload)
{
int type = PD_HEADER_TYPE(head);
int cnt = PD_HEADER_CNT(head);
switch (type) {
#ifdef CONFIG_USB_PD_DUAL_ROLE
case PD_DATA_SOURCE_CAP:
if ((pd[port].task_state == PD_STATE_SNK_DISCOVERY)
|| (pd[port].task_state == PD_STATE_SNK_TRANSITION)
|| (pd[port].task_state == PD_STATE_SNK_REQUESTED)
#ifdef CONFIG_USB_PD_VBUS_DETECT_NONE
|| (pd[port].task_state ==
PD_STATE_SNK_HARD_RESET_RECOVER)
#endif
|| (pd[port].task_state == PD_STATE_SNK_READY)) {
#ifdef CONFIG_USB_PD_REV30
/*
* Only adjust sink rev if source rev is higher.
*/
if (PD_HEADER_REV(head) < pd[port].rev)
pd[port].rev = PD_HEADER_REV(head);
#endif
/* Port partner is now known to be PD capable */
pd[port].flags |= PD_FLAGS_PREVIOUS_PD_CONN;
/* src cap 0 should be fixed PDO */
pd_update_pdo_flags(port, payload[0]);
pd_process_source_cap(port, cnt, payload);
/* Source will resend source cap on failure */
pd_send_request_msg(port, 1);
}
break;
#endif /* CONFIG_USB_PD_DUAL_ROLE */
case PD_DATA_REQUEST:
if ((pd[port].power_role == PD_ROLE_SOURCE) && (cnt == 1)) {
#ifdef CONFIG_USB_PD_REV30
/*
* Adjust the rev level to what the sink supports. If
* they're equal, no harm done.
*/
pd[port].rev = PD_HEADER_REV(head);
#endif
if (!pd_check_requested_voltage(payload[0], port)) {
if (send_control(port, PD_CTRL_ACCEPT) < 0)
/*
* if we fail to send accept, do
* nothing and let sink timeout and
* send hard reset
*/
return;
/* explicit contract is now in place */
pd[port].flags |= PD_FLAGS_EXPLICIT_CONTRACT;
#ifdef CONFIG_USB_PD_DUAL_ROLE
pd_update_saved_port_flags(
port, PD_BBRMFLG_EXPLICIT_CONTRACT, 1);
#endif /* CONFIG_USB_PD_DUAL_ROLE */
#ifdef CONFIG_USB_PD_REV30
/*
* Start Source-coordinated collision
* avoidance
*/
if (pd[port].rev == PD_REV30 &&
pd[port].power_role == PD_ROLE_SOURCE)
sink_can_xmit(port, SINK_TX_OK);
#endif
pd[port].requested_idx = RDO_POS(payload[0]);
set_state(port, PD_STATE_SRC_ACCEPTED);
return;
}
}
/* the message was incorrect or cannot be satisfied */
send_control(port, PD_CTRL_REJECT);
/* keep last contract in place (whether implicit or explicit) */
set_state(port, PD_STATE_SRC_READY);
break;
case PD_DATA_BIST:
/* If not in READY state, then don't start BIST */
if (DUAL_ROLE_IF_ELSE(port,
pd[port].task_state == PD_STATE_SNK_READY,
pd[port].task_state == PD_STATE_SRC_READY)) {
/* currently only support sending bist carrier mode 2 */
if ((payload[0] >> 28) == 5) {
/* bist data object mode is 2 */
pd_transmit(port, TCPC_TX_BIST_MODE_2, 0,
NULL);
/* Set to appropriate port disconnected state */
set_state(port, DUAL_ROLE_IF_ELSE(port,
PD_STATE_SNK_DISCONNECTED,
PD_STATE_SRC_DISCONNECTED));
}
}
break;
case PD_DATA_SINK_CAP:
pd[port].flags |= PD_FLAGS_SNK_CAP_RECVD;
/* snk cap 0 should be fixed PDO */
pd_update_pdo_flags(port, payload[0]);
if (pd[port].task_state == PD_STATE_SRC_GET_SINK_CAP)
set_state(port, PD_STATE_SRC_READY);
break;
#ifdef CONFIG_USB_PD_REV30
case PD_DATA_BATTERY_STATUS:
break;
#endif
case PD_DATA_VENDOR_DEF:
handle_vdm_request(port, cnt, payload);
break;
default:
CPRINTF("C%d Unhandled data message type %d\n", port, type);
}
}
#ifdef CONFIG_USB_PD_DUAL_ROLE
void pd_request_power_swap(int port)
{
if (pd[port].task_state == PD_STATE_SRC_READY)
set_state(port, PD_STATE_SRC_SWAP_INIT);
else if (pd[port].task_state == PD_STATE_SNK_READY)
set_state(port, PD_STATE_SNK_SWAP_INIT);
task_wake(PD_PORT_TO_TASK_ID(port));
}
#ifdef CONFIG_USBC_VCONN_SWAP
static void pd_request_vconn_swap(int port)
{
if (pd[port].task_state == PD_STATE_SRC_READY ||
pd[port].task_state == PD_STATE_SNK_READY)
set_state(port, PD_STATE_VCONN_SWAP_SEND);
task_wake(PD_PORT_TO_TASK_ID(port));
}
void pd_try_vconn_src(int port)
{
/*
* If we don't currently provide vconn, and we can supply it, send
* a vconn swap request.
*/
if (!(pd[port].flags & PD_FLAGS_VCONN_ON)) {
if (pd_check_vconn_swap(port))
pd_request_vconn_swap(port);
}
}
#endif
#endif /* CONFIG_USB_PD_DUAL_ROLE */
void pd_request_data_swap(int port)
{
if (DUAL_ROLE_IF_ELSE(port,
pd[port].task_state == PD_STATE_SNK_READY,
pd[port].task_state == PD_STATE_SRC_READY))
set_state(port, PD_STATE_DR_SWAP);
task_wake(PD_PORT_TO_TASK_ID(port));
}
static void pd_set_power_role(int port, int role)
{
pd[port].power_role = role;
#ifdef CONFIG_USB_PD_DUAL_ROLE
pd_update_saved_port_flags(port, PD_BBRMFLG_POWER_ROLE, role);
#endif /* defined(CONFIG_USB_PD_DUAL_ROLE) */
}
static void pd_dr_swap(int port)
{
pd_set_data_role(port, !pd[port].data_role);
pd[port].flags |= PD_FLAGS_CHECK_IDENTITY;
}
static void handle_ctrl_request(int port, uint16_t head,
uint32_t *payload)
{
int type = PD_HEADER_TYPE(head);
int res;
switch (type) {
case PD_CTRL_GOOD_CRC:
/* should not get it */
break;
case PD_CTRL_PING:
/* Nothing else to do */
break;
case PD_CTRL_GET_SOURCE_CAP:
if (pd[port].task_state == PD_STATE_SRC_READY)
set_state(port, PD_STATE_SRC_DISCOVERY);
else {
res = send_source_cap(port);
if ((res >= 0) &&
(pd[port].task_state == PD_STATE_SRC_DISCOVERY))
set_state(port, PD_STATE_SRC_NEGOCIATE);
}
break;
case PD_CTRL_GET_SINK_CAP:
#ifdef CONFIG_USB_PD_DUAL_ROLE
send_sink_cap(port);
#else
send_control(port, REFUSE(pd[port].rev));
#endif
break;
#ifdef CONFIG_USB_PD_DUAL_ROLE
case PD_CTRL_GOTO_MIN:
#ifdef CONFIG_USB_PD_GIVE_BACK
if (pd[port].task_state == PD_STATE_SNK_READY) {
/*
* Reduce power consumption now!
*
* The source will restore power to this sink
* by sending a new source cap message at a
* later time.
*/
pd_snk_give_back(port, &pd[port].curr_limit,
&pd[port].supply_voltage);
set_state(port, PD_STATE_SNK_TRANSITION);
}
#endif
break;
case PD_CTRL_PS_RDY:
if (pd[port].task_state == PD_STATE_SNK_SWAP_SRC_DISABLE) {
set_state(port, PD_STATE_SNK_SWAP_STANDBY);
} else if (pd[port].task_state == PD_STATE_SRC_SWAP_STANDBY) {
/* reset message ID and swap roles */
pd[port].msg_id = 0;
pd_set_power_role(port, PD_ROLE_SINK);
pd_update_roles(port);
/*
* Give the state machine time to read VBUS as high.
* Note: This is empirically determined, not strictly
* part of the USB PD spec.
*/
pd[port].vbus_debounce_time =
get_time().val + PD_T_DEBOUNCE;
set_state(port, PD_STATE_SNK_DISCOVERY);
#ifdef CONFIG_USBC_VCONN_SWAP
} else if (pd[port].task_state == PD_STATE_VCONN_SWAP_INIT) {
/*
* If VCONN is on, then this PS_RDY tells us it's
* ok to turn VCONN off
*/
if (pd[port].flags & PD_FLAGS_VCONN_ON)
set_state(port, PD_STATE_VCONN_SWAP_READY);
#endif
} else if (pd[port].task_state == PD_STATE_SNK_DISCOVERY) {
/* Don't know what power source is ready. Reset. */
set_state(port, PD_STATE_HARD_RESET_SEND);
} else if (pd[port].task_state == PD_STATE_SNK_SWAP_STANDBY) {
/* Do nothing, assume this is a redundant PD_RDY */
} else if (pd[port].power_role == PD_ROLE_SINK) {
/*
* Give the source some time to send any messages before
* we start our interrogation. Add some jitter of up to
* 100ms, taken from the current system time, to prevent
* multiple collisions.
*/
if (pd[port].task_state == PD_STATE_SNK_TRANSITION)
pd[port].ready_state_holdoff_timer =
get_time().val + READY_HOLD_OFF_US
+ (get_time().le.lo % (100 * MSEC));
set_state(port, PD_STATE_SNK_READY);
pd_set_input_current_limit(port, pd[port].curr_limit,
pd[port].supply_voltage);
#ifdef CONFIG_CHARGE_MANAGER
/* Set ceiling based on what's negotiated */
charge_manager_set_ceil(port,
CEIL_REQUESTOR_PD,
pd[port].curr_limit);
#endif
}
break;
#endif
case PD_CTRL_REJECT:
case PD_CTRL_WAIT:
if (pd[port].task_state == PD_STATE_DR_SWAP) {
if (type == PD_CTRL_WAIT) /* try again ... */
pd[port].flags |= PD_FLAGS_CHECK_DR_ROLE;
set_state(port, READY_RETURN_STATE(port));
}
#ifdef CONFIG_USBC_VCONN_SWAP
else if (pd[port].task_state == PD_STATE_VCONN_SWAP_SEND)
set_state(port, READY_RETURN_STATE(port));
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE
else if (pd[port].task_state == PD_STATE_SRC_SWAP_INIT)
set_state(port, PD_STATE_SRC_READY);
else if (pd[port].task_state == PD_STATE_SNK_SWAP_INIT)
set_state(port, PD_STATE_SNK_READY);
else if (pd[port].task_state == PD_STATE_SNK_REQUESTED) {
/*
* On reception of a WAIT message, transition to
* PD_STATE_SNK_READY after PD_T_SINK_REQUEST ms to
* send another request.
*
* On reception of a REJECT message, transition to
* PD_STATE_SNK_READY but don't resend the request if
* we already have a contract in place.
*
* On reception of a REJECT message without a contract,
* transition to PD_STATE_SNK_DISCOVERY instead.
*/
if (type == PD_CTRL_WAIT) {
/*
* Trigger a new power request when
* we enter PD_STATE_SNK_READY
*/
pd[port].new_power_request = 1;
/*
* After the request is triggered,
* make sure the request is sent.
*/
pd[port].prev_request_mv = 0;
/*
* Transition to PD_STATE_SNK_READY
* after PD_T_SINK_REQUEST ms.
*/
set_state_timeout(port,
get_time().val +
PD_T_SINK_REQUEST,
PD_STATE_SNK_READY);
} else {
/* The request was rejected */
const int in_contract =
pd[port].flags &
PD_FLAGS_EXPLICIT_CONTRACT;
set_state(port,
in_contract ? PD_STATE_SNK_READY
: PD_STATE_SNK_DISCOVERY);
}
}
#endif
break;
case PD_CTRL_ACCEPT:
if (pd[port].task_state == PD_STATE_SOFT_RESET) {
/*
* For the case that we sent soft reset in SNK_DISCOVERY
* on startup due to VBUS never low, clear the flag.
*/
pd[port].flags &= ~PD_FLAGS_VBUS_NEVER_LOW;
execute_soft_reset(port);
} else if (pd[port].task_state == PD_STATE_DR_SWAP) {
/* switch data role */
pd_dr_swap(port);
set_state(port, READY_RETURN_STATE(port));
#ifdef CONFIG_USB_PD_DUAL_ROLE
#ifdef CONFIG_USBC_VCONN_SWAP
} else if (pd[port].task_state == PD_STATE_VCONN_SWAP_SEND) {
/* switch vconn */
set_state(port, PD_STATE_VCONN_SWAP_INIT);
#endif
} else if (pd[port].task_state == PD_STATE_SRC_SWAP_INIT) {
/* explicit contract goes away for power swap */
pd[port].flags &= ~PD_FLAGS_EXPLICIT_CONTRACT;
pd_update_saved_port_flags(port,
PD_BBRMFLG_EXPLICIT_CONTRACT,
0);
set_state(port, PD_STATE_SRC_SWAP_SNK_DISABLE);
} else if (pd[port].task_state == PD_STATE_SNK_SWAP_INIT) {
/* explicit contract goes away for power swap */
pd[port].flags &= ~PD_FLAGS_EXPLICIT_CONTRACT;
pd_update_saved_port_flags(port,
PD_BBRMFLG_EXPLICIT_CONTRACT,
0);
set_state(port, PD_STATE_SNK_SWAP_SNK_DISABLE);
} else if (pd[port].task_state == PD_STATE_SNK_REQUESTED) {
/* explicit contract is now in place */
pd[port].flags |= PD_FLAGS_EXPLICIT_CONTRACT;
pd_update_saved_port_flags(port,
PD_BBRMFLG_EXPLICIT_CONTRACT,
1);
set_state(port, PD_STATE_SNK_TRANSITION);
#endif
}
break;
case PD_CTRL_SOFT_RESET:
execute_soft_reset(port);
/* We are done, acknowledge with an Accept packet */
send_control(port, PD_CTRL_ACCEPT);
break;
case PD_CTRL_PR_SWAP:
#ifdef CONFIG_USB_PD_DUAL_ROLE
if (pd_check_power_swap(port)) {
send_control(port, PD_CTRL_ACCEPT);
/*
* Clear flag for checking power role to avoid
* immediately requesting another swap.
*/
pd[port].flags &= ~PD_FLAGS_CHECK_PR_ROLE;
set_state(port,
DUAL_ROLE_IF_ELSE(port,
PD_STATE_SNK_SWAP_SNK_DISABLE,
PD_STATE_SRC_SWAP_SNK_DISABLE));
} else {
send_control(port, REFUSE(pd[port].rev));
}
#else
send_control(port, REFUSE(pd[port].rev));
#endif
break;
case PD_CTRL_DR_SWAP:
if (pd_check_data_swap(port, pd[port].data_role)) {
/*
* Accept switch and perform data swap. Clear
* flag for checking data role to avoid
* immediately requesting another swap.
*/
pd[port].flags &= ~PD_FLAGS_CHECK_DR_ROLE;
if (send_control(port, PD_CTRL_ACCEPT) >= 0)
pd_dr_swap(port);
} else {
send_control(port, REFUSE(pd[port].rev));
}
break;
case PD_CTRL_VCONN_SWAP:
#ifdef CONFIG_USBC_VCONN_SWAP
if (pd[port].task_state == PD_STATE_SRC_READY ||
pd[port].task_state == PD_STATE_SNK_READY) {
if (pd_check_vconn_swap(port)) {
if (send_control(port, PD_CTRL_ACCEPT) > 0)
set_state(port,
PD_STATE_VCONN_SWAP_INIT);
} else {
send_control(port, REFUSE(pd[port].rev));
}
}
#else
send_control(port, REFUSE(pd[port].rev));
#endif
break;
default:
#ifdef CONFIG_USB_PD_REV30
send_control(port, PD_CTRL_NOT_SUPPORTED);
#endif
CPRINTF("C%d Unhandled ctrl message type %d\n", port, type);
}
}
#ifdef CONFIG_USB_PD_REV30
static void handle_ext_request(int port, uint16_t head, uint32_t *payload)
{
int type = PD_HEADER_TYPE(head);
switch (type) {
case PD_EXT_GET_BATTERY_CAP:
send_battery_cap(port, payload);
break;
case PD_EXT_GET_BATTERY_STATUS:
send_battery_status(port, payload);
break;
case PD_EXT_BATTERY_CAP:
break;
default:
send_control(port, PD_CTRL_NOT_SUPPORTED);
}
}
#endif
static void handle_request(int port, uint16_t head,
uint32_t *payload)
{
int cnt = PD_HEADER_CNT(head);
int data_role = PD_HEADER_DROLE(head);
int p;
/* dump received packet content (only dump ping at debug level 3) */
if ((debug_level == 2 && PD_HEADER_TYPE(head) != PD_CTRL_PING) ||
debug_level >= 3) {
CPRINTF("C%d RECV %04x/%d ", port, head, cnt);
for (p = 0; p < cnt; p++)
CPRINTF("[%d]%08x ", p, payload[p]);
CPRINTF("\n");
}
/*
* If we are in disconnected state, we shouldn't get a request. Do
* a hard reset if we get one.
*/
if (!pd_is_connected(port))
set_state(port, PD_STATE_HARD_RESET_SEND);
/*
* When a data role conflict is detected, USB-C ErrorRecovery
* actions shall be performed, and transitioning to unattached state
* is one such legal action.
*/
if (pd[port].data_role == data_role) {
/*
* If the port doesn't support removing the terminations, just
* go to the unattached state.
*/
if (tcpm_set_cc(port, TYPEC_CC_OPEN) == EC_SUCCESS) {
/* Do not drive VBUS or VCONN. */
pd_power_supply_reset(port);
#ifdef CONFIG_USBC_VCONN
set_vconn(port, 0);
#endif /* defined(CONFIG_USBC_VCONN) */
usleep(PD_T_ERROR_RECOVERY);
/* Restore terminations. */
tcpm_set_cc(port, DUAL_ROLE_IF_ELSE(port, TYPEC_CC_RD,
TYPEC_CC_RP));
}
set_state(port,
DUAL_ROLE_IF_ELSE(port,
PD_STATE_SNK_DISCONNECTED,
PD_STATE_SRC_DISCONNECTED));
return;
}
#ifdef CONFIG_USB_PD_REV30
/* Check if this is an extended chunked data message. */
if (pd[port].rev == PD_REV30 && PD_HEADER_EXT(head)) {
handle_ext_request(port, head, payload);
return;
}
#endif
if (cnt)
handle_data_request(port, head, payload);
else
handle_ctrl_request(port, head, payload);
}
void pd_send_vdm(int port, uint32_t vid, int cmd, const uint32_t *data,
int count)
{
if (count > VDO_MAX_SIZE - 1) {
CPRINTF("C%d VDM over max size\n", port);
return;
}
/* set VDM header with VID & CMD */
pd[port].vdo_data[0] = VDO(vid, ((vid & USB_SID_PD) == USB_SID_PD) ?
1 : (PD_VDO_CMD(cmd) <= CMD_ATTENTION), cmd);
#ifdef CONFIG_USB_PD_REV30
pd[port].vdo_data[0] |= VDO_SVDM_VERS(vdo_ver[pd[port].rev]);
#endif
queue_vdm(port, pd[port].vdo_data, data, count);
task_wake(PD_PORT_TO_TASK_ID(port));
}
static inline int pdo_busy(int port)
{
/*
* Note, main PDO state machine (pd_task) uses READY state exclusively
* to denote port partners have successfully negociated a contract. All
* other protocol actions force state transitions.
*/
int rv = (pd[port].task_state != PD_STATE_SRC_READY);
#ifdef CONFIG_USB_PD_DUAL_ROLE
rv &= (pd[port].task_state != PD_STATE_SNK_READY);
#endif
return rv;
}
static uint64_t vdm_get_ready_timeout(uint32_t vdm_hdr)
{
uint64_t timeout;
int cmd = PD_VDO_CMD(vdm_hdr);
/* its not a structured VDM command */
if (!PD_VDO_SVDM(vdm_hdr))
return 500*MSEC;
switch (PD_VDO_CMDT(vdm_hdr)) {
case CMDT_INIT:
if ((cmd == CMD_ENTER_MODE) || (cmd == CMD_EXIT_MODE))
timeout = PD_T_VDM_WAIT_MODE_E;
else
timeout = PD_T_VDM_SNDR_RSP;
break;
default:
if ((cmd == CMD_ENTER_MODE) || (cmd == CMD_EXIT_MODE))
timeout = PD_T_VDM_E_MODE;
else
timeout = PD_T_VDM_RCVR_RSP;
break;
}
return timeout;
}
static void pd_vdm_send_state_machine(int port)
{
int res;
uint16_t header;
switch (pd[port].vdm_state) {
case VDM_STATE_READY:
/* Only transmit VDM if connected. */
if (!pd_is_connected(port)) {
pd[port].vdm_state = VDM_STATE_ERR_BUSY;
break;
}
/*
* if there's traffic or we're not in PDO ready state don't send
* a VDM.
*/
if (pdo_busy(port))
break;
/*
* To communicate with the cable plug, an explicit contract
* should be established, VCONN should be enabled and data role
* that can communicate with the cable plug should be in place.
* For USB3.0, UFP/DFP can communicate whereas in case of
* USB2.0 only DFP can talk to the cable plug.
*
* For communication between USB2.0 UFP and cable plug,
* data role swap takes place during source and sink
* negotiation and in case of failure, a soft reset is issued.
*/
if (is_sop_prime_ready(port, pd[port].data_role,
pd[port].flags)) {
/* Prepare SOP'/SOP'' header and send VDM */
header = PD_HEADER(PD_DATA_VENDOR_DEF, PD_PLUG_DFP_UFP,
0, pd[port].msg_id,
(int)pd[port].vdo_count,
pd_get_rev(port), 0);
res = pd_transmit(port, TCPC_TX_SOP_PRIME, header,
pd[port].vdo_data);
/*
* If there is no ack from the cable, its a non-emark
* cable and since, the pd flow should continue
* irrespective of cable response, sending
* discover_svid so the pd flow remains intact.
*/
if (res < 0) {
header = PD_HEADER(PD_DATA_VENDOR_DEF,
pd[port].power_role,
pd[port].data_role,
pd[port].msg_id,
(int)pd[port].vdo_count,
pd_get_rev(port), 0);
pd[port].vdo_data[0] =
VDO(USB_SID_PD, 1, CMD_DISCOVER_SVID);
res = pd_transmit(port, TCPC_TX_SOP, header,
pd[port].vdo_data);
reset_pd_cable(port);
}
} else {
/* Prepare SOP header and send VDM */
header = PD_HEADER(PD_DATA_VENDOR_DEF,
pd[port].power_role,
pd[port].data_role,
pd[port].msg_id,
(int)pd[port].vdo_count,
pd_get_rev(port), 0);
res = pd_transmit(port, TCPC_TX_SOP, header,
pd[port].vdo_data);
}
if (res < 0) {
pd[port].vdm_state = VDM_STATE_ERR_SEND;
} else {
pd[port].vdm_state = VDM_STATE_BUSY;
pd[port].vdm_timeout.val = get_time().val +
vdm_get_ready_timeout(pd[port].vdo_data[0]);
}
break;
case VDM_STATE_WAIT_RSP_BUSY:
/* wait and then initiate request again */
if (get_time().val > pd[port].vdm_timeout.val) {
pd[port].vdo_data[0] = pd[port].vdo_retry;
pd[port].vdo_count = 1;
pd[port].vdm_state = VDM_STATE_READY;
}
break;
case VDM_STATE_BUSY:
/* Wait for VDM response or timeout */
if (pd[port].vdm_timeout.val &&
(get_time().val > pd[port].vdm_timeout.val)) {
pd[port].vdm_state = VDM_STATE_ERR_TMOUT;
}
break;
default:
break;
}
}
#ifdef CONFIG_CMD_PD_DEV_DUMP_INFO
static inline void pd_dev_dump_info(uint16_t dev_id, uint8_t *hash)
{
int j;
ccprintf("DevId:%d.%d Hash:", HW_DEV_ID_MAJ(dev_id),
HW_DEV_ID_MIN(dev_id));
for (j = 0; j < PD_RW_HASH_SIZE; j += 4) {
ccprintf(" 0x%02x%02x%02x%02x", hash[j + 3], hash[j + 2],
hash[j + 1], hash[j]);
}
ccprintf("\n");
}
#endif /* CONFIG_CMD_PD_DEV_DUMP_INFO */
int pd_dev_store_rw_hash(int port, uint16_t dev_id, uint32_t *rw_hash,
uint32_t current_image)
{
#ifdef CONFIG_COMMON_RUNTIME
int i;
#endif
pd[port].dev_id = dev_id;
memcpy(pd[port].dev_rw_hash, rw_hash, PD_RW_HASH_SIZE);
#ifdef CONFIG_CMD_PD_DEV_DUMP_INFO
if (debug_level >= 2)
pd_dev_dump_info(dev_id, (uint8_t *)rw_hash);
#endif
pd[port].current_image = current_image;
#ifdef CONFIG_COMMON_RUNTIME
/* Search table for matching device / hash */
for (i = 0; i < RW_HASH_ENTRIES; i++)
if (dev_id == rw_hash_table[i].dev_id)
return !memcmp(rw_hash,
rw_hash_table[i].dev_rw_hash,
PD_RW_HASH_SIZE);
#endif
return 0;
}
#if defined(CONFIG_POWER_COMMON) || defined(CONFIG_USB_PD_ALT_MODE_DFP)
static void exit_dp_mode(int port)
{
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
int opos = pd_alt_mode(port, USB_SID_DISPLAYPORT);
if (opos <= 0)
return;
CPRINTS("C%d Exiting DP mode", port);
if (!pd_dfp_exit_mode(port, USB_SID_DISPLAYPORT, opos))
return;
pd_send_vdm(port, USB_SID_DISPLAYPORT,
CMD_EXIT_MODE | VDO_OPOS(opos), NULL, 0);
pd_vdm_send_state_machine(port);
/* Have to wait for ACK */
#endif /* CONFIG_USB_PD_ALT_MODE_DFP */
}
#endif /* CONFIG_POWER_COMMON */
#ifdef CONFIG_POWER_COMMON
static void handle_new_power_state(int port)
{
if (chipset_in_or_transitioning_to_state(CHIPSET_STATE_ANY_OFF))
/* The SoC will negotiated DP mode again when it boots up */
exit_dp_mode(port);
/* Ensure mux is set properly after chipset transition */
set_usb_mux_with_current_data_role(port);
}
#endif /* CONFIG_POWER_COMMON */
#ifdef CONFIG_USB_PD_DUAL_ROLE
enum pd_dual_role_states pd_get_dual_role(int port)
{
return drp_state[port];
}
#ifdef CONFIG_USB_PD_TRY_SRC
static void pd_update_try_source(void)
{
int i;
int try_src = 0;
int batt_soc = usb_get_battery_soc();
try_src = 0;
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++)
try_src |= drp_state[i] == PD_DRP_TOGGLE_ON;
/*
* Enable try source when dual-role toggling AND battery is present
* and at some minimum percentage.
*/
pd_try_src_enable = try_src &&
batt_soc >= CONFIG_USB_PD_TRY_SRC_MIN_BATT_SOC;
#ifdef CONFIG_BATTERY_REVIVE_DISCONNECT
/*
* Don't attempt Try.Src if the battery is in the disconnect state. The
* discharge FET may not be enabled and so attempting Try.Src may cut
* off our only power source at the time.
*/
pd_try_src_enable &= (battery_get_disconnect_state() ==
BATTERY_NOT_DISCONNECTED);
#elif defined(CONFIG_BATTERY_PRESENT_CUSTOM) || \
defined(CONFIG_BATTERY_PRESENT_GPIO)
/*
* When battery is cutoff in ship mode it may not be reliable to
* check if battery is present with its state of charge.
* Also check if battery is initialized and ready to provide power.
*/
pd_try_src_enable &= (battery_is_present() == BP_YES);
#endif /* CONFIG_BATTERY_PRESENT_[CUSTOM|GPIO] */
/*
* Clear this flag to cover case where a TrySrc
* mode went from enabled to disabled and trying_source
* was active at that time.
*/
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++)
pd[i].flags &= ~PD_FLAGS_TRY_SRC;
}
#endif /* CONFIG_USB_PD_TRY_SRC */
#ifdef CONFIG_USB_PD_RESET_MIN_BATT_SOC
static void pd_update_snk_reset(void)
{
int i;
int batt_soc = usb_get_battery_soc();
if (batt_soc < CONFIG_USB_PD_RESET_MIN_BATT_SOC)
return;
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++) {
if (pd[i].flags & PD_FLAGS_SNK_WAITING_BATT) {
/*
* Battery has gained sufficient charge to kick off PD
* negotiation and withstand a hard reset. Clear the
* flag and let reset begin if task is waiting in
* SNK_DISCOVERY.
*/
pd[i].flags &= ~PD_FLAGS_SNK_WAITING_BATT;
if (pd[i].task_state == PD_STATE_SNK_DISCOVERY) {
CPRINTS("C%d: Starting soft reset timer", i);
set_state_timeout(i,
get_time().val + PD_T_SINK_WAIT_CAP,
PD_STATE_SOFT_RESET);
}
}
}
}
#endif
#if defined(CONFIG_USB_PD_TRY_SRC) || defined(CONFIG_USB_PD_RESET_MIN_BATT_SOC)
static void pd_update_battery_soc_change(void)
{
#ifdef CONFIG_USB_PD_TRY_SRC
pd_update_try_source();
#endif
#ifdef CONFIG_USB_PD_RESET_MIN_BATT_SOC
pd_update_snk_reset();
#endif
}
DECLARE_HOOK(HOOK_BATTERY_SOC_CHANGE, pd_update_battery_soc_change,
HOOK_PRIO_DEFAULT);
#endif /* CONFIG_USB_PD_TRY_SRC || CONFIG_USB_PD_RESET_MIN_BATT_SOC */
static inline void pd_set_dual_role_no_wakeup(int port,
enum pd_dual_role_states state)
{
drp_state[port] = state;
#ifdef CONFIG_USB_PD_TRY_SRC
pd_update_try_source();
#endif
}
void pd_set_dual_role(int port, enum pd_dual_role_states state)
{
pd_set_dual_role_no_wakeup(port, state);
/* Wake task up to process change */
task_set_event(PD_PORT_TO_TASK_ID(port),
PD_EVENT_UPDATE_DUAL_ROLE, 0);
}
/* This must only be called from the PD task */
static void pd_update_dual_role_config(int port)
{
/*
* Change to sink if port is currently a source AND (new DRP
* state is force sink OR new DRP state is either toggle off
* or debug accessory toggle only and we are in the source
* disconnected state).
*/
if (pd[port].power_role == PD_ROLE_SOURCE &&
((drp_state[port] == PD_DRP_FORCE_SINK && !pd_ts_dts_plugged(port))
|| (drp_state[port] == PD_DRP_TOGGLE_OFF
&& pd[port].task_state == PD_STATE_SRC_DISCONNECTED))) {
pd_set_power_role(port, PD_ROLE_SINK);
set_state(port, PD_STATE_SNK_DISCONNECTED);
tcpm_set_cc(port, TYPEC_CC_RD);
/* Make sure we're not sourcing VBUS. */
pd_power_supply_reset(port);
}
/*
* Change to source if port is currently a sink and the
* new DRP state is force source.
*/
if (pd[port].power_role == PD_ROLE_SINK &&
drp_state[port] == PD_DRP_FORCE_SOURCE) {
pd_set_power_role(port, PD_ROLE_SOURCE);
set_state(port, PD_STATE_SRC_DISCONNECTED);
tcpm_set_cc(port, TYPEC_CC_RP);
}
}
int pd_get_role(int port)
{
return pd[port].power_role;
}
static int pd_is_power_swapping(int port)
{
/* return true if in the act of swapping power roles */
return pd[port].task_state == PD_STATE_SNK_SWAP_SNK_DISABLE ||
pd[port].task_state == PD_STATE_SNK_SWAP_SRC_DISABLE ||
pd[port].task_state == PD_STATE_SNK_SWAP_STANDBY ||
pd[port].task_state == PD_STATE_SNK_SWAP_COMPLETE ||
pd[port].task_state == PD_STATE_SRC_SWAP_SNK_DISABLE ||
pd[port].task_state == PD_STATE_SRC_SWAP_SRC_DISABLE ||
pd[port].task_state == PD_STATE_SRC_SWAP_STANDBY;
}
/*
* Provide Rp to ensure the partner port is in a known state (eg. not
* PD negotiated, not sourcing 20V).
*/
static void pd_partner_port_reset(int port)
{
uint64_t timeout;
uint8_t flags;
/*
* If there is no contract in place (or if we fail to read the BBRAM
* flags), there is no need to reset the partner.
*/
if (pd_get_saved_port_flags(port, &flags) != EC_SUCCESS ||
!(flags & PD_BBRMFLG_EXPLICIT_CONTRACT))
return;
/*
* If we reach here, an explicit contract is in place.
*
* If PD communications are allowed, don't apply Rp. We'll issue a
* SoftReset later on and renegotiate our contract. This particular
* condition only applies to unlocked RO images with an explicit
* contract in place.
*/
if (pd_comm_is_enabled(port))
return;
/* If we just lost power, don't apply Rp. */
if (system_get_reset_flags() &
(EC_RESET_FLAG_BROWNOUT | EC_RESET_FLAG_POWER_ON))
return;
/*
* Clear the active contract bit before we apply Rp in case we
* intentionally brown out because we cut off our only power supply.
*/
pd_update_saved_port_flags(port, PD_BBRMFLG_EXPLICIT_CONTRACT, 0);
/* Provide Rp for 200 msec. or until we no longer have VBUS. */
CPRINTF("C%d Apply Rp!\n", port);
cflush();
tcpm_set_cc(port, TYPEC_CC_RP);
timeout = get_time().val + 200 * MSEC;
while (get_time().val < timeout && pd_is_vbus_present(port))
msleep(10);
}
#endif /* CONFIG_USB_PD_DUAL_ROLE */
#ifdef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
static enum pd_states drp_auto_toggle_next_state(int port,
enum tcpc_cc_voltage_status cc1, enum tcpc_cc_voltage_status cc2)
{
enum pd_states next_state;
/* Set to appropriate port state */
if (cc_is_open(cc1, cc2)) {
/*
* If nothing is attached then use drp_state to determine next
* state. If DRP auto toggle is still on, then remain in the
* DRP_AUTO_TOGGLE state. Otherwise, stop dual role toggling
* and go to a disconnected state.
*/
switch (drp_state[port]) {
case PD_DRP_TOGGLE_OFF:
next_state = PD_DEFAULT_STATE(port);
break;
case PD_DRP_FREEZE:
if (pd[port].power_role == PD_ROLE_SINK)
next_state = PD_STATE_SNK_DISCONNECTED;
else
next_state = PD_STATE_SRC_DISCONNECTED;
break;
case PD_DRP_FORCE_SINK:
next_state = PD_STATE_SNK_DISCONNECTED;
break;
case PD_DRP_FORCE_SOURCE:
next_state = PD_STATE_SRC_DISCONNECTED;
break;
case PD_DRP_TOGGLE_ON:
default:
next_state = PD_STATE_DRP_AUTO_TOGGLE;
break;
}
} else if ((cc_is_rp(cc1) || cc_is_rp(cc2)) &&
drp_state[port] != PD_DRP_FORCE_SOURCE) {
/* SNK allowed unless ForceSRC */
next_state = PD_STATE_SNK_DISCONNECTED;
} else if (cc_is_at_least_one_rd(cc1, cc2) ||
cc_is_audio_acc(cc1, cc2)) {
/*
* SRC allowed unless ForceSNK or Toggle Off
*
* Ideally we wouldn't use auto-toggle when drp_state is
* TOGGLE_OFF/FORCE_SINK, but for some TCPCs, auto-toggle can't
* be prevented in low power mode. Try being a sink in case the
* connected device is dual-role (this ensures reliable charging
* from a hub, b/72007056). 100 ms is enough time for a
* dual-role partner to switch from sink to source. If the
* connected device is sink-only, then we will attempt
* SNK_DISCONNECTED twice (due to debounce time), then return to
* low power mode (and stay there). After 200 ms, reset ready
* for a new connection.
*/
if (drp_state[port] == PD_DRP_TOGGLE_OFF ||
drp_state[port] == PD_DRP_FORCE_SINK) {
if (get_time().val > pd[port].drp_sink_time + 200*MSEC)
pd[port].drp_sink_time = get_time().val;
if (get_time().val < pd[port].drp_sink_time + 100*MSEC)
next_state = PD_STATE_SNK_DISCONNECTED;
else
next_state = PD_STATE_DRP_AUTO_TOGGLE;
} else
next_state = PD_STATE_SRC_DISCONNECTED;
} else
/* Anything else, keep toggling */
next_state = PD_STATE_DRP_AUTO_TOGGLE;
return next_state;
}
#endif /* CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE */
int pd_get_polarity(int port)
{
return pd[port].polarity;
}
int pd_get_partner_data_swap_capable(int port)
{
/* return data swap capable status of port partner */
return pd[port].flags & PD_FLAGS_PARTNER_DR_DATA;
}
#ifdef CONFIG_COMMON_RUNTIME
void pd_comm_enable(int port, int enable)
{
/* We don't check port >= CONFIG_USB_PD_PORT_COUNT deliberately */
pd_comm_enabled[port] = enable;
/* If type-C connection, then update the TCPC RX enable */
if (pd_is_connected(port))
tcpm_set_rx_enable(port, enable);
#ifdef CONFIG_USB_PD_DUAL_ROLE
/*
* If communications are enabled, start hard reset timer for
* any port in PD_SNK_DISCOVERY.
*/
if (enable && pd[port].task_state == PD_STATE_SNK_DISCOVERY)
set_state_timeout(port,
get_time().val + PD_T_SINK_WAIT_CAP,
PD_STATE_HARD_RESET_SEND);
#endif
}
#endif
void pd_ping_enable(int port, int enable)
{
if (enable)
pd[port].flags |= PD_FLAGS_PING_ENABLED;
else
pd[port].flags &= ~PD_FLAGS_PING_ENABLED;
}
#if defined(CONFIG_CHARGE_MANAGER)
/**
* Signal power request to indicate a charger update that affects the port.
*/
void pd_set_new_power_request(int port)
{
pd[port].new_power_request = 1;
task_wake(PD_PORT_TO_TASK_ID(port));
}
#endif /* CONFIG_CHARGE_MANAGER */
#if defined(CONFIG_USBC_BACKWARDS_COMPATIBLE_DFP) && defined(CONFIG_USBC_SS_MUX)
/*
* Backwards compatible DFP does not support USB SS because it applies VBUS
* before debouncing CC and setting USB SS muxes, but SS detection will fail
* before we are done debouncing CC.
*/
#error "Backwards compatible DFP does not support USB"
#endif
#ifdef CONFIG_COMMON_RUNTIME
/* Initialize globals based on system state. */
static void pd_init_tasks(void)
{
static int initialized;
int enable = 1;
int i;
/* Initialize globals once, for all PD tasks. */
if (initialized)
return;
#if defined(HAS_TASK_CHIPSET) && defined(CONFIG_USB_PD_DUAL_ROLE)
/* Set dual-role state based on chipset power state */
if (chipset_in_state(CHIPSET_STATE_ANY_OFF))
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++)
drp_state[i] = PD_DRP_FORCE_SINK;
else if (chipset_in_state(CHIPSET_STATE_ANY_SUSPEND))
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++)
drp_state[i] = PD_DRP_TOGGLE_OFF;
else /* CHIPSET_STATE_ON */
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++)
drp_state[i] = PD_DRP_TOGGLE_ON;
#endif
#if defined(CONFIG_USB_PD_COMM_DISABLED)
enable = 0;
#elif defined(CONFIG_USB_PD_COMM_LOCKED)
/* Disable PD communication at init if we're in RO and locked. */
if (!system_is_in_rw() && system_is_locked())
enable = 0;
#ifdef CONFIG_VBOOT_EFS
if (vboot_need_pd_comm())
enable = 1;
#endif
#endif
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++)
pd_comm_enabled[i] = enable;
CPRINTS("PD comm %sabled", enable ? "en" : "dis");
initialized = 1;
}
#endif /* CONFIG_COMMON_RUNTIME */
#if !defined(CONFIG_USB_PD_TCPC) && defined(CONFIG_USB_PD_DUAL_ROLE)
static int pd_restart_tcpc(int port)
{
if (board_set_tcpc_power_mode) {
/* force chip reset */
board_set_tcpc_power_mode(port, 0);
}
return tcpm_init(port);
}
#endif
/* High-priority interrupt tasks implementations */
#if defined(HAS_TASK_PD_INT_C0) || defined(HAS_TASK_PD_INT_C1) || \
defined(HAS_TASK_PD_INT_C2)
/* Used to conditionally compile code in main pd task. */
#define HAS_DEFFERED_INTERRUPT_HANDLER
/* Events for pd_interrupt_handler_task */
#define PD_PROCESS_INTERRUPT BIT(0)
static uint8_t pd_int_task_id[CONFIG_USB_PD_PORT_COUNT];
void schedule_deferred_pd_interrupt(const int port)
{
task_set_event(pd_int_task_id[port], PD_PROCESS_INTERRUPT, 0);
}
/*
* Theoretically, we may need to support up to 480 USB-PD packets per second for
* intensive operations such as FW update over PD. This value has tested well
* preventing watchdog resets with a single bad port partner plugged in.
*/
#define ALERT_STORM_MAX_COUNT 480
#define ALERT_STORM_INTERVAL SECOND
/**
* Main task entry point that handles PD interrupts for a single port
*
* @param p The PD port number for which to handle interrupts (pointer is
* reinterpreted as an integer directly).
*/
void pd_interrupt_handler_task(void *p)
{
const int port = (int) p;
const int port_mask = (PD_STATUS_TCPC_ALERT_0 << port);
struct {
int count;
uint32_t time;
} storm_tracker[CONFIG_USB_PD_PORT_COUNT] = {};
ASSERT(port >= 0 && port < CONFIG_USB_PD_PORT_COUNT);
pd_int_task_id[port] = task_get_current();
while (1) {
const int evt = task_wait_event(-1);
if (evt & PD_PROCESS_INTERRUPT) {
/*
* While the interrupt signal is asserted; we have more
* work to do. This effectively makes the interrupt a
* level-interrupt instead of an edge-interrupt without
* having to enable/disable a real level-interrupt in
* multiple locations.
*
* Also, if the port is disabled do not process
* interrupts. Upon existing suspend, we schedule a
* PD_PROCESS_INTERRUPT to check if we missed anything.
*/
while ((tcpc_get_alert_status() & port_mask) &&
pd_is_port_enabled(port)) {
uint32_t now;
tcpc_alert(port);
now = get_time().le.lo;
if (time_after(now, storm_tracker[port].time)) {
storm_tracker[port].time =
now + ALERT_STORM_INTERVAL;
/*
* Start at 1 since we are processing
* an interrupt now
*/
storm_tracker[port].count = 1;
} else if (++storm_tracker[port].count >
ALERT_STORM_MAX_COUNT) {
CPRINTS("C%d Interrupt storm detected. "
"Disabling port for 5 seconds.",
port);
pd_set_suspend(port, 1);
pd_deferred_resume(port);
}
}
}
}
}
#endif /* HAS_TASK_PD_INT_C0 || HAS_TASK_PD_INT_C1 || HAS_TASK_PD_INT_C2 */
void pd_task(void *u)
{
int head;
int port = TASK_ID_TO_PD_PORT(task_get_current());
uint32_t payload[7];
int timeout = 10*MSEC;
enum tcpc_cc_voltage_status cc1, cc2;
int res, incoming_packet = 0;
int hard_reset_count = 0;
#ifdef CONFIG_USB_PD_DUAL_ROLE
uint64_t next_role_swap = PD_T_DRP_SNK;
uint8_t saved_flgs = 0;
#ifndef CONFIG_USB_PD_VBUS_DETECT_NONE
int snk_hard_reset_vbus_off = 0;
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
const int auto_toggle_supported = tcpm_auto_toggle_supported(port);
#endif
#if defined(CONFIG_CHARGE_MANAGER)
typec_current_t typec_curr = 0, typec_curr_change = 0;
#endif /* CONFIG_CHARGE_MANAGER */
#endif /* CONFIG_USB_PD_DUAL_ROLE */
enum pd_states this_state;
enum pd_cc_states new_cc_state;
timestamp_t now;
uint64_t next_src_cap = 0;
int caps_count = 0, hard_reset_sent = 0;
int snk_cap_count = 0;
int evt;
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/*
* Set the ports in Low Power Mode so that other tasks wait until
* TCPC is initialized and ready.
*/
pd[port].flags |= PD_FLAGS_LPM_ENGAGED;
#endif
#ifdef CONFIG_COMMON_RUNTIME
pd_init_tasks();
#endif
/*
* Ensure the power supply is in the default state and ensure we are not
* sourcing Vconn
*/
pd_power_supply_reset(port);
#ifdef CONFIG_USBC_VCONN
set_vconn(port, 0);
#endif
/* Initialize TCPM driver and wait for TCPC to be ready */
res = reset_device_and_notify(port);
invalidate_last_message_id(port);
#ifdef CONFIG_USB_PD_DUAL_ROLE
pd_partner_port_reset(port);
#endif
this_state = res ? PD_STATE_SUSPENDED : PD_DEFAULT_STATE(port);
#ifndef CONFIG_USB_PD_TCPC
if (!res) {
struct ec_response_pd_chip_info_v1 *info;
if (tcpm_get_chip_info(port, 0, &info) ==
EC_SUCCESS) {
CPRINTS("TCPC p%d VID:0x%x PID:0x%x DID:0x%x FWV:0x%lx",
port, info->vendor_id, info->product_id,
info->device_id, info->fw_version_number);
}
}
#endif
#ifdef CONFIG_USB_PD_REV30
/* Set Revision to highest */
pd[port].rev = PD_REV30;
pd_ca_reset(port);
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE
/*
* If VBUS is high, then initialize flag for VBUS has always been
* present. This flag is used to maintain a PD connection after a
* reset by sending a soft reset.
*/
pd[port].flags |=
pd_is_vbus_present(port) ? PD_FLAGS_VBUS_NEVER_LOW : 0;
#endif
/* Disable TCPC RX until connection is established */
tcpm_set_rx_enable(port, 0);
#ifdef CONFIG_USBC_SS_MUX
/* Initialize USB mux to its default state */
usb_mux_init(port);
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE
/*
* If there's an explicit contract in place, let's restore the data and
* power roles such that any messages we send to the port partner will
* still be valid.
*/
if (pd_comm_is_enabled(port) &&
(pd_get_saved_port_flags(port, &saved_flgs) == EC_SUCCESS) &&
(saved_flgs & PD_BBRMFLG_EXPLICIT_CONTRACT)) {
/* Only attempt to maintain previous sink contracts */
if ((saved_flgs & PD_BBRMFLG_POWER_ROLE) == PD_ROLE_SINK) {
pd_set_power_role(port,
(saved_flgs & PD_BBRMFLG_POWER_ROLE) ?
PD_ROLE_SOURCE : PD_ROLE_SINK);
pd_set_data_role(port,
(saved_flgs & PD_BBRMFLG_DATA_ROLE) ?
PD_ROLE_DFP : PD_ROLE_UFP);
#ifdef CONFIG_USBC_VCONN
pd_set_vconn_role(port,
(saved_flgs & PD_BBRMFLG_VCONN_ROLE) ?
PD_ROLE_VCONN_ON : PD_ROLE_VCONN_OFF);
#endif /* CONFIG_USBC_VCONN */
/*
* Since there is an explicit contract in place, let's
* issue a SoftReset such that we can renegotiate with
* our port partner in order to synchronize our state
* machines.
*/
this_state = PD_STATE_SOFT_RESET;
/*
* Re-discover any alternate modes we may have been
* using with this port partner.
*/
pd[port].flags |= PD_FLAGS_CHECK_IDENTITY;
} else {
/*
* Vbus was turned off during the power supply reset
* earlier, so clear the contract flag and re-start as
* default role
*/
pd_update_saved_port_flags(port,
PD_BBRMFLG_EXPLICIT_CONTRACT, 0);
}
/*
* Set the TCPC reset event such that we can set our CC
* terminations, determine polarity, and enable RX so we
* can hear back from our port partner if maintaining our old
* connection.
*/
task_set_event(task_get_current(), PD_EVENT_TCPC_RESET, 0);
}
#endif /* defined(CONFIG_USB_PD_DUAL_ROLE) */
/* Set the power role if we haven't already. */
if (this_state != PD_STATE_SOFT_RESET)
pd_set_power_role(port, PD_ROLE_DEFAULT(port));
/* Initialize PD protocol state variables for each port. */
pd[port].vdm_state = VDM_STATE_DONE;
set_state(port, this_state);
tcpm_select_rp_value(port, CONFIG_USB_PD_PULLUP);
#ifdef CONFIG_USB_PD_DUAL_ROLE
/*
* If we're not in an explicit contract, set our terminations to match
* our default power role.
*/
if (!(saved_flgs & PD_BBRMFLG_EXPLICIT_CONTRACT))
#endif /* CONFIG_USB_PD_DUAL_ROLE */
tcpm_set_cc(port, PD_ROLE_DEFAULT(port) == PD_ROLE_SOURCE ?
TYPEC_CC_RP : TYPEC_CC_RD);
#ifdef CONFIG_USBC_PPC
/*
* Wait to initialize the PPC after setting the correct Rd values in
* the TCPC otherwise the TCPC might not be pulling the CC lines down
* when the PPC connects the CC lines from the USB connector to the
* TCPC cause the source to drop Vbus causing a brown out.
*/
ppc_init(port);
#endif
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
/* Initialize PD Policy engine */
pd_dfp_pe_init(port);
#endif
#ifdef CONFIG_CHARGE_MANAGER
/* Initialize PD and type-C supplier current limits to 0 */
pd_set_input_current_limit(port, 0, 0);
typec_set_input_current_limit(port, 0, 0);
charge_manager_update_dualrole(port, CAP_UNKNOWN);
#endif
#ifdef HAS_DEFFERED_INTERRUPT_HANDLER
/*
* Since most boards configure the TCPC interrupt as edge
* and it is possible that the interrupt line was asserted between init
* and calling set_state, we need to process any pending interrupts now.
* Otherwise future interrupts will never fire because another edge
* never happens. Note this needs to happen after set_state() is called.
*/
schedule_deferred_pd_interrupt(port);
#endif
while (1) {
#ifdef CONFIG_USB_PD_REV30
/* send any pending messages */
pd_ca_send_pending(port);
#endif
/* process VDM messages last */
pd_vdm_send_state_machine(port);
/* Verify board specific health status : current, voltages... */
res = pd_board_checks();
if (res != EC_SUCCESS) {
/* cut the power */
pd_execute_hard_reset(port);
/* notify the other side of the issue */
pd_transmit(port, TCPC_TX_HARD_RESET, 0, NULL);
}
/* wait for next event/packet or timeout expiration */
evt = task_wait_event(timeout);
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
if (evt & PD_EXIT_LOW_POWER_EVENT_MASK)
exit_low_power_mode(port);
if (evt & PD_EVENT_DEVICE_ACCESSED)
handle_device_access(port);
#endif
#ifdef CONFIG_POWER_COMMON
if (evt & PD_EVENT_POWER_STATE_CHANGE)
handle_new_power_state(port);
#endif
#if defined(CONFIG_USB_PD_ALT_MODE_DFP)
if (evt & PD_EVENT_SYSJUMP) {
exit_dp_mode(port);
notify_sysjump_ready(&sysjump_task_waiting);
}
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE
if (evt & PD_EVENT_UPDATE_DUAL_ROLE)
pd_update_dual_role_config(port);
#endif
#ifdef CONFIG_USB_PD_TCPC
/*
* run port controller task to check CC and/or read incoming
* messages
*/
tcpc_run(port, evt);
#else
/* if TCPC has reset, then need to initialize it again */
if (evt & PD_EVENT_TCPC_RESET) {
reset_device_and_notify(port);
#ifdef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
}
if ((evt & PD_EVENT_TCPC_RESET) &&
(pd[port].task_state != PD_STATE_DRP_AUTO_TOGGLE)) {
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE
if (pd[port].task_state == PD_STATE_SOFT_RESET) {
enum tcpc_cc_voltage_status cc1, cc2;
/*
* Set the terminations to match our power
* role.
*/
tcpm_set_cc(port, pd[port].power_role ?
TYPEC_CC_RP : TYPEC_CC_RD);
/* Determine the polarity. */
tcpm_get_cc(port, &cc1, &cc2);
if (pd[port].power_role == PD_ROLE_SINK) {
pd[port].polarity =
get_snk_polarity(cc1, cc2);
} else {
pd[port].polarity =
(cc1 != TYPEC_CC_VOLT_RD);
}
} else
#endif /* CONFIG_USB_PD_DUAL_ROLE */
{
/* Ensure CC termination is default */
tcpm_set_cc(port, PD_ROLE_DEFAULT(port) ==
PD_ROLE_SOURCE ? TYPEC_CC_RP :
TYPEC_CC_RD);
}
/*
* If we have a stable contract in the default role,
* then simply update TCPC with some missing info
* so that we can continue without resetting PD comms.
* Otherwise, go to the default disconnected state
* and force renegotiation.
*/
if (pd[port].vdm_state == VDM_STATE_DONE && (
#ifdef CONFIG_USB_PD_DUAL_ROLE
(PD_ROLE_DEFAULT(port) == PD_ROLE_SINK &&
pd[port].task_state == PD_STATE_SNK_READY) ||
(pd[port].task_state == PD_STATE_SOFT_RESET) ||
#endif
(PD_ROLE_DEFAULT(port) == PD_ROLE_SOURCE &&
pd[port].task_state == PD_STATE_SRC_READY))) {
set_polarity(port, pd[port].polarity);
tcpm_set_msg_header(port, pd[port].power_role,
pd[port].data_role);
tcpm_set_rx_enable(port, 1);
} else {
/* Ensure state variables are at default */
pd_set_power_role(port, PD_ROLE_DEFAULT(port));
pd[port].vdm_state = VDM_STATE_DONE;
set_state(port, PD_DEFAULT_STATE(port));
}
}
#endif
#ifdef CONFIG_USBC_PPC
/*
* TODO: Useful for non-PPC cases as well, but only needed
* for PPC cases right now. Revisit later.
*/
if (evt & PD_EVENT_SEND_HARD_RESET)
set_state(port, PD_STATE_HARD_RESET_SEND);
#endif /* defined(CONFIG_USBC_PPC) */
/* process any potential incoming message */
incoming_packet = tcpm_has_pending_message(port);
if (incoming_packet) {
/* Dequeue and consume duplicate message ID. */
if (tcpm_dequeue_message(port, payload, &head) ==
EC_SUCCESS
&& !consume_repeat_message(port, head)
)
handle_request(port, head, payload);
/* Check if there are any more messages */
if (tcpm_has_pending_message(port))
task_set_event(PD_PORT_TO_TASK_ID(port),
TASK_EVENT_WAKE, 0);
}
if (pd[port].req_suspend_state)
set_state(port, PD_STATE_SUSPENDED);
/* if nothing to do, verify the state of the world in 500ms */
this_state = pd[port].task_state;
timeout = 500*MSEC;
switch (this_state) {
case PD_STATE_DISABLED:
/* Nothing to do */
break;
case PD_STATE_SRC_DISCONNECTED:
timeout = 10*MSEC;
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/*
* If SW decided we should be in a low power state and
* the CC lines did not change, then don't talk with the
* TCPC otherwise we might wake it up.
*/
if (pd[port].flags & PD_FLAGS_LPM_REQUESTED &&
!(evt & PD_EVENT_CC)) {
timeout = -1;
break;
}
#endif /* CONFIG_USB_PD_TCPC_LOW_POWER */
tcpm_get_cc(port, &cc1, &cc2);
#ifdef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
/*
* Attempt TCPC auto DRP toggle if it is
* not already auto toggling and not try.src
*/
if (auto_toggle_supported &&
!(pd[port].flags & PD_FLAGS_TCPC_DRP_TOGGLE) &&
!is_try_src(port) &&
cc_is_open(cc1, cc2)) {
set_state(port, PD_STATE_DRP_AUTO_TOGGLE);
timeout = 2*MSEC;
break;
}
#endif
/*
* Transition to DEBOUNCE if we detect appropriate
* signals
*
* (from 4.5.2.2.10.2 Exiting from Try.SRC State)
* If try_src -and-
* have only one Rd (not both) => DEBOUNCE
*
* (from 4.5.2.2.7.2 Exiting from Unattached.SRC State)
* If not try_src -and-
* have at least one Rd => DEBOUNCE -or-
* have audio access => DEBOUNCE
*
* try_src should not exit if both pins are Rd
*/
if ((is_try_src(port) && cc_is_only_one_rd(cc1, cc2)) ||
(!is_try_src(port) &&
(cc_is_at_least_one_rd(cc1, cc2) ||
cc_is_audio_acc(cc1, cc2)))) {
#ifdef CONFIG_USBC_BACKWARDS_COMPATIBLE_DFP
/* Enable VBUS */
if (pd_set_power_supply_ready(port))
break;
#endif
pd[port].cc_state = PD_CC_NONE;
set_state(port,
PD_STATE_SRC_DISCONNECTED_DEBOUNCE);
break;
}
#if defined(CONFIG_USB_PD_DUAL_ROLE)
now = get_time();
/*
* Try.SRC state is embedded here. The port
* shall transition to TryWait.SNK after
* tDRPTry (PD_T_DRP_TRY) and Vbus is within
* vSafe0V, or after tTryTimeout
* (PD_T_TRY_TIMEOUT). Otherwise we should stay
* within Try.SRC (break).
*/
if (is_try_src(port)) {
if (now.val < pd[port].try_src_marker) {
break;
} else if (now.val < pd[port].try_timeout) {
if (pd_is_vbus_present(port))
break;
}
/*
* Transition to TryWait.SNK now, so set
* state and update src marker time.
*/
set_state(port, PD_STATE_SNK_DISCONNECTED);
pd_set_power_role(port, PD_ROLE_SINK);
tcpm_set_cc(port, TYPEC_CC_RD);
pd[port].try_src_marker =
get_time().val + PD_T_DEBOUNCE;
timeout = 2 * MSEC;
break;
}
/*
* If Try.SRC state is not active, then handle
* the normal DRP toggle from SRC->SNK.
*/
if (now.val < next_role_swap ||
drp_state[port] == PD_DRP_FORCE_SOURCE ||
drp_state[port] == PD_DRP_FREEZE)
break;
/*
* Transition to SNK now, so set state and
* update next role swap time.
*/
set_state(port, PD_STATE_SNK_DISCONNECTED);
pd_set_power_role(port, PD_ROLE_SINK);
tcpm_set_cc(port, TYPEC_CC_RD);
next_role_swap = get_time().val + PD_T_DRP_SNK;
/* Swap states quickly */
timeout = 2 * MSEC;
#endif
break;
case PD_STATE_SRC_DISCONNECTED_DEBOUNCE:
timeout = 20*MSEC;
tcpm_get_cc(port, &cc1, &cc2);
if (cc_is_snk_dbg_acc(cc1, cc2)) {
/* Debug accessory */
new_cc_state = PD_CC_UFP_DEBUG_ACC;
} else if (cc_is_at_least_one_rd(cc1, cc2)) {
/* UFP attached */
new_cc_state = PD_CC_UFP_ATTACHED;
} else if (cc_is_audio_acc(cc1, cc2)) {
/* Audio accessory */
new_cc_state = PD_CC_UFP_AUDIO_ACC;
} else {
/* No UFP */
set_state(port, PD_STATE_SRC_DISCONNECTED);
timeout = 5*MSEC;
break;
}
/* Set debounce timer */
if (new_cc_state != pd[port].cc_state) {
pd[port].cc_debounce =
get_time().val +
(is_try_src(port) ? PD_T_DEBOUNCE
: PD_T_CC_DEBOUNCE);
pd[port].cc_state = new_cc_state;
break;
}
/* Debounce the cc state */
if (get_time().val < pd[port].cc_debounce)
break;
/* Debounce complete */
if (IS_ENABLED(CONFIG_COMMON_RUNTIME))
hook_notify(HOOK_USB_PD_CONNECT);
#ifdef CONFIG_USBC_PPC
/*
* If the port is latched off, just continue to
* monitor for a detach.
*/
if (ppc_is_port_latched_off(port))
break;
#endif /* CONFIG_USBC_PPC */
/* UFP is attached */
if (new_cc_state == PD_CC_UFP_ATTACHED ||
new_cc_state == PD_CC_UFP_DEBUG_ACC) {
#ifdef CONFIG_USBC_PPC
/* Inform PPC that a sink is connected. */
ppc_sink_is_connected(port, 1);
#endif /* CONFIG_USBC_PPC */
pd[port].polarity = (cc1 != TYPEC_CC_VOLT_RD);
set_polarity(port, pd[port].polarity);
/* initial data role for source is DFP */
pd_set_data_role(port, PD_ROLE_DFP);
if (new_cc_state == PD_CC_UFP_DEBUG_ACC)
pd[port].flags |=
PD_FLAGS_TS_DTS_PARTNER;
#ifdef CONFIG_USBC_VCONN
/*
* Do not source Vconn when debug accessory is
* detected. Section 4.5.2.2.17.1 in USB spec
* v1-3
*/
if (new_cc_state != PD_CC_UFP_DEBUG_ACC) {
/*
* Start sourcing Vconn before Vbus to
* ensure we are within USB Type-C
* Spec 1.3 tVconnON.
*/
set_vconn(port, 1);
pd_set_vconn_role(port,
PD_ROLE_VCONN_ON);
}
#endif
#ifndef CONFIG_USBC_BACKWARDS_COMPATIBLE_DFP
/* Enable VBUS */
if (pd_set_power_supply_ready(port)) {
#ifdef CONFIG_USBC_VCONN
/* Stop sourcing Vconn if Vbus failed */
set_vconn(port, 0);
pd_set_vconn_role(port,
PD_ROLE_VCONN_OFF);
#endif /* CONFIG_USBC_VCONN */
#ifdef CONFIG_USBC_SS_MUX
usb_mux_set(port, TYPEC_MUX_NONE,
USB_SWITCH_DISCONNECT,
pd[port].polarity);
#endif /* CONFIG_USBC_SS_MUX */
break;
}
/*
* Set correct Rp value determined during
* pd_set_power_supply_ready. This should be
* safe because Vconn is being sourced,
* preventing incorrect CCD detection.
*/
tcpm_set_cc(port, TYPEC_CC_RP);
#endif /* CONFIG_USBC_BACKWARDS_COMPATIBLE_DFP */
/* If PD comm is enabled, enable TCPC RX */
if (pd_comm_is_enabled(port))
tcpm_set_rx_enable(port, 1);
pd[port].flags |= PD_FLAGS_CHECK_PR_ROLE |
PD_FLAGS_CHECK_DR_ROLE;
hard_reset_count = 0;
timeout = 5*MSEC;
set_state(port, PD_STATE_SRC_STARTUP);
}
/*
* AUDIO_ACC will remain in this state indefinitely
* until disconnect.
*/
break;
case PD_STATE_SRC_HARD_RESET_RECOVER:
/* Do not continue until hard reset recovery time */
if (get_time().val < pd[port].src_recover) {
timeout = 50*MSEC;
break;
}
#ifdef CONFIG_USBC_VCONN
/*
* Start sourcing Vconn again and set the flag, in case
* it was 0 due to a previous swap
*/
set_vconn(port, 1);
pd_set_vconn_role(port, PD_ROLE_VCONN_ON);
#endif
/* Enable VBUS */
timeout = 10*MSEC;
if (pd_set_power_supply_ready(port)) {
set_state(port, PD_STATE_SRC_DISCONNECTED);
break;
}
#ifdef CONFIG_USB_PD_TCPM_TCPCI
/*
* After transmitting hard reset, TCPM writes
* to RECEIVE_DETECT register to enable
* PD message passing.
*/
if (pd_comm_is_enabled(port))
tcpm_set_rx_enable(port, 1);
#endif /* CONFIG_USB_PD_TCPM_TCPCI */
set_state(port, PD_STATE_SRC_STARTUP);
break;
case PD_STATE_SRC_STARTUP:
/* Reset cable attributes and flags */
reset_pd_cable(port);
/* Wait for power source to enable */
if (pd[port].last_state != pd[port].task_state) {
pd[port].flags |= PD_FLAGS_CHECK_IDENTITY;
/* reset various counters */
caps_count = 0;
pd[port].msg_id = 0;
snk_cap_count = 0;
set_state_timeout(
port,
#ifdef CONFIG_USBC_BACKWARDS_COMPATIBLE_DFP
/*
* delay for power supply to start up.
* subtract out debounce time if coming
* from debounce state since vbus is
* on during debounce.
*/
get_time().val +
PD_POWER_SUPPLY_TURN_ON_DELAY -
(pd[port].last_state ==
PD_STATE_SRC_DISCONNECTED_DEBOUNCE
? PD_T_CC_DEBOUNCE : 0),
#else
get_time().val +
PD_POWER_SUPPLY_TURN_ON_DELAY,
#endif
PD_STATE_SRC_DISCOVERY);
}
break;
case PD_STATE_SRC_DISCOVERY:
now = get_time();
if (pd[port].last_state != pd[port].task_state) {
caps_count = 0;
next_src_cap = now.val;
/*
* If we have had PD connection with this port
* partner, then start NoResponseTimer.
*/
if (pd_capable(port))
set_state_timeout(port,
get_time().val +
PD_T_NO_RESPONSE,
hard_reset_count <
PD_HARD_RESET_COUNT ?
PD_STATE_HARD_RESET_SEND :
PD_STATE_SRC_DISCONNECTED);
}
/* Send source cap some minimum number of times */
if (caps_count < PD_CAPS_COUNT &&
next_src_cap <= now.val) {
/* Query capabilities of the other side */
res = send_source_cap(port);
/* packet was acked => PD capable device) */
if (res >= 0) {
set_state(port,
PD_STATE_SRC_NEGOCIATE);
timeout = 10*MSEC;
hard_reset_count = 0;
caps_count = 0;
/* Port partner is PD capable */
pd[port].flags |=
PD_FLAGS_PREVIOUS_PD_CONN;
} else { /* failed, retry later */
timeout = PD_T_SEND_SOURCE_CAP;
next_src_cap = now.val +
PD_T_SEND_SOURCE_CAP;
caps_count++;
}
} else if (caps_count < PD_CAPS_COUNT) {
timeout = next_src_cap - now.val;
}
break;
case PD_STATE_SRC_NEGOCIATE:
/* wait for a "Request" message */
if (pd[port].last_state != pd[port].task_state)
set_state_timeout(port,
get_time().val +
PD_T_SENDER_RESPONSE,
PD_STATE_HARD_RESET_SEND);
break;
case PD_STATE_SRC_ACCEPTED:
/* Accept sent, wait for enabling the new voltage */
if (pd[port].last_state != pd[port].task_state)
set_state_timeout(
port,
get_time().val +
PD_T_SINK_TRANSITION,
PD_STATE_SRC_POWERED);
break;
case PD_STATE_SRC_POWERED:
/* Switch to the new requested voltage */
if (pd[port].last_state != pd[port].task_state) {
pd_transition_voltage(pd[port].requested_idx);
set_state_timeout(
port,
get_time().val +
PD_POWER_SUPPLY_TURN_ON_DELAY,
PD_STATE_SRC_TRANSITION);
}
break;
case PD_STATE_SRC_TRANSITION:
/* the voltage output is good, notify the source */
res = send_control(port, PD_CTRL_PS_RDY);
if (res >= 0) {
timeout = 10*MSEC;
/*
* Give the sink some time to send any messages
* before we may send messages of our own. Add
* some jitter of up to 100ms, taken from the
* current system time, to prevent multiple
* collisions.
*/
pd[port].ready_state_holdoff_timer =
get_time().val + READY_HOLD_OFF_US
+ (get_time().le.lo % (100 * MSEC));
/* it'a time to ping regularly the sink */
set_state(port, PD_STATE_SRC_READY);
} else {
/* The sink did not ack, cut the power... */
set_state(port, PD_STATE_SRC_DISCONNECTED);
}
break;
case PD_STATE_SRC_READY:
timeout = PD_T_SOURCE_ACTIVITY;
/*
* Don't send any traffic yet until our holdoff timer
* has expired. Some devices are chatty once we reach
* the SRC_READY state and we may end up in a collision
* of messages if we try to immediately send our
* interrogations.
*/
if (get_time().val <=
pd[port].ready_state_holdoff_timer)
break;
/*
* Don't send any PD traffic if we woke up due to
* incoming packet or if VDO response pending to avoid
* collisions.
*/
if (incoming_packet ||
(pd[port].vdm_state == VDM_STATE_BUSY))
break;
/* Send updated source capabilities to our partner */
if (pd[port].flags & PD_FLAGS_UPDATE_SRC_CAPS) {
res = send_source_cap(port);
if (res >= 0) {
set_state(port,
PD_STATE_SRC_NEGOCIATE);
pd[port].flags &=
~PD_FLAGS_UPDATE_SRC_CAPS;
}
break;
}
/* Send get sink cap if haven't received it yet */
if (!(pd[port].flags & PD_FLAGS_SNK_CAP_RECVD)) {
if (++snk_cap_count <= PD_SNK_CAP_RETRIES) {
/* Get sink cap to know if dual-role device */
send_control(port, PD_CTRL_GET_SINK_CAP);
set_state(port, PD_STATE_SRC_GET_SINK_CAP);
break;
} else if (debug_level >= 2 &&
snk_cap_count == PD_SNK_CAP_RETRIES+1) {
CPRINTF("C%d ERR SNK_CAP\n", port);
}
}
/* Check power role policy, which may trigger a swap */
if (pd[port].flags & PD_FLAGS_CHECK_PR_ROLE) {
pd_check_pr_role(port, PD_ROLE_SOURCE,
pd[port].flags);
pd[port].flags &= ~PD_FLAGS_CHECK_PR_ROLE;
break;
}
/* Check data role policy, which may trigger a swap */
if (pd[port].flags & PD_FLAGS_CHECK_DR_ROLE) {
pd_check_dr_role(port, pd[port].data_role,
pd[port].flags);
pd[port].flags &= ~PD_FLAGS_CHECK_DR_ROLE;
break;
}
/* Send discovery SVDMs last */
if (pd[port].data_role == PD_ROLE_DFP &&
(pd[port].flags & PD_FLAGS_CHECK_IDENTITY)) {
#ifndef CONFIG_USB_PD_SIMPLE_DFP
pd_send_vdm(port, USB_SID_PD,
CMD_DISCOVER_IDENT, NULL, 0);
#endif
pd[port].flags &= ~PD_FLAGS_CHECK_IDENTITY;
break;
}
if (!(pd[port].flags & PD_FLAGS_PING_ENABLED))
break;
/* Verify that the sink is alive */
res = send_control(port, PD_CTRL_PING);
if (res >= 0)
break;
/* Ping dropped. Try soft reset. */
set_state(port, PD_STATE_SOFT_RESET);
timeout = 10 * MSEC;
break;
case PD_STATE_SRC_GET_SINK_CAP:
if (pd[port].last_state != pd[port].task_state)
set_state_timeout(port,
get_time().val +
PD_T_SENDER_RESPONSE,
PD_STATE_SRC_READY);
break;
case PD_STATE_DR_SWAP:
if (pd[port].last_state != pd[port].task_state) {
res = send_control(port, PD_CTRL_DR_SWAP);
if (res < 0) {
timeout = 10*MSEC;
/*
* If failed to get goodCRC, send
* soft reset, otherwise ignore
* failure.
*/
set_state(port, res == -1 ?
PD_STATE_SOFT_RESET :
READY_RETURN_STATE(port));
break;
}
/* Wait for accept or reject */
set_state_timeout(port,
get_time().val +
PD_T_SENDER_RESPONSE,
READY_RETURN_STATE(port));
}
break;
#ifdef CONFIG_USB_PD_DUAL_ROLE
case PD_STATE_SRC_SWAP_INIT:
if (pd[port].last_state != pd[port].task_state) {
res = send_control(port, PD_CTRL_PR_SWAP);
if (res < 0) {
timeout = 10*MSEC;
/*
* If failed to get goodCRC, send
* soft reset, otherwise ignore
* failure.
*/
set_state(port, res == -1 ?
PD_STATE_SOFT_RESET :
PD_STATE_SRC_READY);
break;
}
/* Wait for accept or reject */
set_state_timeout(port,
get_time().val +
PD_T_SENDER_RESPONSE,
PD_STATE_SRC_READY);
}
break;
case PD_STATE_SRC_SWAP_SNK_DISABLE:
/* Give time for sink to stop drawing current */
if (pd[port].last_state != pd[port].task_state)
set_state_timeout(port,
get_time().val +
PD_T_SINK_TRANSITION,
PD_STATE_SRC_SWAP_SRC_DISABLE);
break;
case PD_STATE_SRC_SWAP_SRC_DISABLE:
if (pd[port].last_state != pd[port].task_state) {
/* Turn power off */
pd_power_supply_reset(port);
/*
* Switch to Rd and swap roles to sink
*
* The reason we do this as early as possible is
* to help prevent CC disconnection cases where
* both partners are applying an Rp. Certain PD
* stacks (e.g. qualcomm), reflexively apply
* their Rp once VBUS falls beneath
* ~3.67V. (b/77827528).
*/
tcpm_set_cc(port, TYPEC_CC_RD);
pd_set_power_role(port, PD_ROLE_SINK);
/* Inform TCPC of power role update. */
pd_update_roles(port);
set_state_timeout(port,
get_time().val +
PD_POWER_SUPPLY_TURN_OFF_DELAY,
PD_STATE_SRC_SWAP_STANDBY);
}
break;
case PD_STATE_SRC_SWAP_STANDBY:
/* Send PS_RDY to let sink know our power is off */
if (pd[port].last_state != pd[port].task_state) {
/* Send PS_RDY */
res = send_control(port, PD_CTRL_PS_RDY);
if (res < 0) {
timeout = 10*MSEC;
set_state(port,
PD_STATE_SRC_DISCONNECTED);
break;
}
/* Wait for PS_RDY from new source */
set_state_timeout(port,
get_time().val +
PD_T_PS_SOURCE_ON,
PD_STATE_SNK_DISCONNECTED);
}
break;
case PD_STATE_SUSPENDED: {
#ifndef CONFIG_USB_PD_TCPC
int rstatus;
#endif
CPRINTS("TCPC p%d suspended!", port);
pd[port].req_suspend_state = 0;
#ifdef CONFIG_USB_PD_TCPC
pd_rx_disable_monitoring(port);
pd_hw_release(port);
pd_power_supply_reset(port);
#else
rstatus = tcpm_release(port);
if (rstatus != 0 && rstatus != EC_ERROR_UNIMPLEMENTED)
CPRINTS("TCPC p%d release failed!", port);
#endif
/* Drain any outstanding software message queues. */
tcpm_clear_pending_messages(port);
/* Wait for resume */
while (pd[port].task_state == PD_STATE_SUSPENDED) {
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
int evt = task_wait_event(-1);
if (evt & PD_EVENT_SYSJUMP)
/* Nothing to do for sysjump prep */
notify_sysjump_ready(
&sysjump_task_waiting);
#else
task_wait_event(-1);
#endif
}
#ifdef CONFIG_USB_PD_TCPC
pd_hw_init(port, PD_ROLE_DEFAULT(port));
CPRINTS("TCPC p%d resumed!", port);
#else
if (rstatus != EC_ERROR_UNIMPLEMENTED &&
pd_restart_tcpc(port) != 0) {
/* stay in PD_STATE_SUSPENDED */
CPRINTS("TCPC p%d restart failed!", port);
break;
}
/* Set the CC termination and state back to default */
tcpm_set_cc(port,
PD_ROLE_DEFAULT(port) == PD_ROLE_SOURCE ?
TYPEC_CC_RP :
TYPEC_CC_RD);
set_state(port, PD_DEFAULT_STATE(port));
CPRINTS("TCPC p%d resumed!", port);
#endif
break;
}
case PD_STATE_SNK_DISCONNECTED:
#ifdef CONFIG_USB_PD_LOW_POWER
timeout = (drp_state[port] !=
PD_DRP_TOGGLE_ON ? SECOND : 10*MSEC);
#else
timeout = 10*MSEC;
#endif
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/*
* If SW decided we should be in a low power state and
* the CC lines did not change, then don't talk with the
* TCPC otherwise we might wake it up.
*/
if (pd[port].flags & PD_FLAGS_LPM_REQUESTED &&
!(evt & PD_EVENT_CC)) {
timeout = -1;
break;
}
#endif /* CONFIG_USB_PD_TCPC_LOW_POWER */
tcpm_get_cc(port, &cc1, &cc2);
#ifdef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
/*
* Attempt TCPC auto DRP toggle if it is not already
* auto toggling and not try.src, and dual role toggling
* is allowed.
*/
if (auto_toggle_supported &&
!(pd[port].flags & PD_FLAGS_TCPC_DRP_TOGGLE) &&
!is_try_src(port) &&
cc_is_open(cc1, cc2) &&
(drp_state[port] == PD_DRP_TOGGLE_ON)) {
set_state(port, PD_STATE_DRP_AUTO_TOGGLE);
timeout = 2*MSEC;
break;
}
#endif
/* Source connection monitoring */
if (!cc_is_open(cc1, cc2)) {
pd[port].cc_state = PD_CC_NONE;
hard_reset_count = 0;
new_cc_state = PD_CC_NONE;
pd[port].cc_debounce = get_time().val +
PD_T_CC_DEBOUNCE;
set_state(port,
PD_STATE_SNK_DISCONNECTED_DEBOUNCE);
timeout = 10*MSEC;
break;
}
/*
* If Try.SRC is active and failed to detect a SNK,
* then it transitions to TryWait.SNK. Need to prevent
* normal dual role toggle until tDRPTryWait timer
* expires.
*/
if (pd[port].flags & PD_FLAGS_TRY_SRC) {
if (get_time().val > pd[port].try_src_marker)
pd[port].flags &= ~PD_FLAGS_TRY_SRC;
break;
}
/* If no source detected, check for role toggle. */
if (drp_state[port] == PD_DRP_TOGGLE_ON &&
get_time().val >= next_role_swap) {
/* Swap roles to source */
pd_set_power_role(port, PD_ROLE_SOURCE);
set_state(port, PD_STATE_SRC_DISCONNECTED);
tcpm_set_cc(port, TYPEC_CC_RP);
next_role_swap = get_time().val + PD_T_DRP_SRC;
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/*
* Clear low power mode flag as we are swapping
* states quickly.
*/
pd[port].flags &= ~PD_FLAGS_LPM_REQUESTED;
#endif
/* Swap states quickly */
timeout = 2*MSEC;
break;
}
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/*
* If we are remaining in the SNK_DISCONNECTED state,
* let's go into low power mode and wait for a change on
* CC status.
*/
pd[port].flags |= PD_FLAGS_LPM_REQUESTED;
#endif/* CONFIG_USB_PD_TCPC_LOW_POWER */
break;
case PD_STATE_SNK_DISCONNECTED_DEBOUNCE:
tcpm_get_cc(port, &cc1, &cc2);
if (cc_is_rp(cc1) && cc_is_rp(cc2)) {
/* Debug accessory */
new_cc_state = PD_CC_DFP_DEBUG_ACC;
} else if (cc_is_rp(cc1) || cc_is_rp(cc2)) {
new_cc_state = PD_CC_DFP_ATTACHED;
} else {
/* No connection any more */
set_state(port, PD_STATE_SNK_DISCONNECTED);
timeout = 5*MSEC;
break;
}
timeout = 20*MSEC;
/* Debounce the cc state */
if (new_cc_state != pd[port].cc_state) {
pd[port].cc_debounce = get_time().val +
PD_T_CC_DEBOUNCE;
pd[port].cc_state = new_cc_state;
break;
}
/* Wait for CC debounce and VBUS present */
if (get_time().val < pd[port].cc_debounce ||
!pd_is_vbus_present(port))
break;
if (pd_try_src_enable &&
!(pd[port].flags & PD_FLAGS_TRY_SRC)) {
/*
* If TRY_SRC is enabled, but not active,
* then force attempt to connect as source.
*/
pd[port].try_src_marker = get_time().val
+ PD_T_DRP_TRY;
pd[port].try_timeout = get_time().val
+ PD_T_TRY_TIMEOUT;
/* Swap roles to source */
pd_set_power_role(port, PD_ROLE_SOURCE);
tcpm_set_cc(port, TYPEC_CC_RP);
timeout = 2*MSEC;
set_state(port, PD_STATE_SRC_DISCONNECTED);
/* Set flag after the state change */
pd[port].flags |= PD_FLAGS_TRY_SRC;
break;
}
/* We are attached */
if (IS_ENABLED(CONFIG_COMMON_RUNTIME))
hook_notify(HOOK_USB_PD_CONNECT);
pd[port].polarity = get_snk_polarity(cc1, cc2);
set_polarity(port, pd[port].polarity);
/* reset message ID on connection */
pd[port].msg_id = 0;
/* initial data role for sink is UFP */
pd_set_data_role(port, PD_ROLE_UFP);
#if defined(CONFIG_CHARGE_MANAGER)
typec_curr = usb_get_typec_current_limit(
pd[port].polarity, cc1, cc2);
typec_set_input_current_limit(
port, typec_curr, TYPE_C_VOLTAGE);
#endif
/* If PD comm is enabled, enable TCPC RX */
if (pd_comm_is_enabled(port))
tcpm_set_rx_enable(port, 1);
/* DFP is attached */
if (new_cc_state == PD_CC_DFP_ATTACHED ||
new_cc_state == PD_CC_DFP_DEBUG_ACC) {
pd[port].flags |= PD_FLAGS_CHECK_PR_ROLE |
PD_FLAGS_CHECK_DR_ROLE |
PD_FLAGS_CHECK_IDENTITY;
/* Reset cable attributes and flags */
reset_pd_cable(port);
if (new_cc_state == PD_CC_DFP_DEBUG_ACC)
pd[port].flags |=
PD_FLAGS_TS_DTS_PARTNER;
set_state(port, PD_STATE_SNK_DISCOVERY);
timeout = 10*MSEC;
hook_call_deferred(
&pd_usb_billboard_deferred_data,
PD_T_AME);
}
break;
case PD_STATE_SNK_HARD_RESET_RECOVER:
if (pd[port].last_state != pd[port].task_state)
pd[port].flags |= PD_FLAGS_CHECK_IDENTITY;
#ifdef CONFIG_USB_PD_VBUS_DETECT_NONE
/*
* Can't measure vbus state so this is the maximum
* recovery time for the source.
*/
if (pd[port].last_state != pd[port].task_state)
set_state_timeout(port, get_time().val +
PD_T_SAFE_0V +
PD_T_SRC_RECOVER_MAX +
PD_T_SRC_TURN_ON,
PD_STATE_SNK_DISCONNECTED);
#else
/* Wait for VBUS to go low and then high*/
if (pd[port].last_state != pd[port].task_state) {
snk_hard_reset_vbus_off = 0;
set_state_timeout(port,
get_time().val +
PD_T_SAFE_0V,
hard_reset_count <
PD_HARD_RESET_COUNT ?
PD_STATE_HARD_RESET_SEND :
PD_STATE_SNK_DISCOVERY);
}
if (!pd_is_vbus_present(port) &&
!snk_hard_reset_vbus_off) {
/* VBUS has gone low, reset timeout */
snk_hard_reset_vbus_off = 1;
set_state_timeout(port,
get_time().val +
PD_T_SRC_RECOVER_MAX +
PD_T_SRC_TURN_ON,
PD_STATE_SNK_DISCONNECTED);
}
if (pd_is_vbus_present(port) &&
snk_hard_reset_vbus_off) {
#ifdef CONFIG_USB_PD_TCPM_TCPCI
/*
* After transmitting hard reset, TCPM writes
* to RECEIVE_MESSAGE register to enable
* PD message passing.
*/
if (pd_comm_is_enabled(port))
tcpm_set_rx_enable(port, 1);
#endif /* CONFIG_USB_PD_TCPM_TCPCI */
/* VBUS went high again */
set_state(port, PD_STATE_SNK_DISCOVERY);
timeout = 10*MSEC;
}
/*
* Don't need to set timeout because VBUS changing
* will trigger an interrupt and wake us up.
*/
#endif
break;
case PD_STATE_SNK_DISCOVERY:
/* Wait for source cap expired only if we are enabled */
if ((pd[port].last_state != pd[port].task_state)
&& pd_comm_is_enabled(port)) {
#ifdef CONFIG_USB_PD_RESET_MIN_BATT_SOC
/*
* If the battery has not met a configured safe
* level for hard resets, refrain from starting
* reset timers as a hard reset could brown out
* the board. Note this may mean that
* high-power chargers will stay at 15W until a
* reset is sent, depending on boot timing.
*/
int batt_soc = usb_get_battery_soc();
if (batt_soc < CONFIG_USB_PD_RESET_MIN_BATT_SOC)
pd[port].flags |=
PD_FLAGS_SNK_WAITING_BATT;
else
pd[port].flags &=
~PD_FLAGS_SNK_WAITING_BATT;
#endif
if (pd[port].flags &
PD_FLAGS_SNK_WAITING_BATT) {
#ifdef CONFIG_CHARGE_MANAGER
/*
* Configure this port as dedicated for
* now, so it won't be de-selected by
* the charge manager leaving safe mode.
*/
charge_manager_update_dualrole(port,
CAP_DEDICATED);
#endif
CPRINTS("C%d: Battery low. "
"Hold reset timer", port);
/*
* If VBUS has never been low, and we timeout
* waiting for source cap, try a soft reset
* first, in case we were already in a stable
* contract before this boot.
*/
} else if (pd[port].flags &
PD_FLAGS_VBUS_NEVER_LOW) {
set_state_timeout(port,
get_time().val +
PD_T_SINK_WAIT_CAP,
PD_STATE_SOFT_RESET);
/*
* If we haven't passed hard reset counter,
* start SinkWaitCapTimer, otherwise start
* NoResponseTimer.
*/
} else if (hard_reset_count <
PD_HARD_RESET_COUNT) {
set_state_timeout(port,
get_time().val +
PD_T_SINK_WAIT_CAP,
PD_STATE_HARD_RESET_SEND);
} else if (pd_capable(port)) {
/* ErrorRecovery */
set_state_timeout(port,
get_time().val +
PD_T_NO_RESPONSE,
PD_STATE_SNK_DISCONNECTED);
}
#if defined(CONFIG_CHARGE_MANAGER)
/*
* If we didn't come from disconnected, must
* have come from some path that did not set
* typec current limit. So, set to 0 so that
* we guarantee this is revised below.
*/
if (pd[port].last_state !=
PD_STATE_SNK_DISCONNECTED_DEBOUNCE)
typec_curr = 0;
#endif
}
#if defined(CONFIG_CHARGE_MANAGER)
timeout = PD_T_SINK_ADJ - PD_T_DEBOUNCE;
/* Check if CC pull-up has changed */
tcpm_get_cc(port, &cc1, &cc2);
if (typec_curr != usb_get_typec_current_limit(
pd[port].polarity, cc1, cc2)) {
/* debounce signal by requiring two reads */
if (typec_curr_change) {
/* set new input current limit */
typec_curr =
usb_get_typec_current_limit(
pd[port].polarity,
cc1, cc2);
typec_set_input_current_limit(
port, typec_curr, TYPE_C_VOLTAGE);
} else {
/* delay for debounce */
timeout = PD_T_DEBOUNCE;
}
typec_curr_change = !typec_curr_change;
} else {
typec_curr_change = 0;
}
#endif
break;
case PD_STATE_SNK_REQUESTED:
/* Wait for ACCEPT or REJECT */
if (pd[port].last_state != pd[port].task_state) {
hard_reset_count = 0;
set_state_timeout(port,
get_time().val +
PD_T_SENDER_RESPONSE,
PD_STATE_HARD_RESET_SEND);
}
break;
case PD_STATE_SNK_TRANSITION:
/* Wait for PS_RDY */
if (pd[port].last_state != pd[port].task_state)
set_state_timeout(port,
get_time().val +
PD_T_PS_TRANSITION,
PD_STATE_HARD_RESET_SEND);
break;
case PD_STATE_SNK_READY:
timeout = 20*MSEC;
/*
* Don't send any traffic yet until our holdoff timer
* has expired. Some devices are chatty once we reach
* the SNK_READY state and we may end up in a collision
* of messages if we try to immediately send our
* interrogations.
*/
if (get_time().val <=
pd[port].ready_state_holdoff_timer)
break;
/*
* Don't send any PD traffic if we woke up due to
* incoming packet or if VDO response pending to avoid
* collisions.
*/
if (incoming_packet ||
(pd[port].vdm_state == VDM_STATE_BUSY))
break;
/* Check for new power to request */
if (pd[port].new_power_request) {
if (pd_send_request_msg(port, 0) != EC_SUCCESS)
set_state(port, PD_STATE_SOFT_RESET);
break;
}
/* Check power role policy, which may trigger a swap */
if (pd[port].flags & PD_FLAGS_CHECK_PR_ROLE) {
pd_check_pr_role(port, PD_ROLE_SINK,
pd[port].flags);
pd[port].flags &= ~PD_FLAGS_CHECK_PR_ROLE;
break;
}
/* Check data role policy, which may trigger a swap */
if (pd[port].flags & PD_FLAGS_CHECK_DR_ROLE) {
pd_check_dr_role(port, pd[port].data_role,
pd[port].flags);
pd[port].flags &= ~PD_FLAGS_CHECK_DR_ROLE;
break;
}
/* If DFP, send discovery SVDMs */
if (pd[port].data_role == PD_ROLE_DFP &&
(pd[port].flags & PD_FLAGS_CHECK_IDENTITY)) {
pd_send_vdm(port, USB_SID_PD,
CMD_DISCOVER_IDENT, NULL, 0);
pd[port].flags &= ~PD_FLAGS_CHECK_IDENTITY;
break;
}
/* Sent all messages, don't need to wake very often */
timeout = 200*MSEC;
break;
case PD_STATE_SNK_SWAP_INIT:
if (pd[port].last_state != pd[port].task_state) {
res = send_control(port, PD_CTRL_PR_SWAP);
if (res < 0) {
timeout = 10*MSEC;
/*
* If failed to get goodCRC, send
* soft reset, otherwise ignore
* failure.
*/
set_state(port, res == -1 ?
PD_STATE_SOFT_RESET :
PD_STATE_SNK_READY);
break;
}
/* Wait for accept or reject */
set_state_timeout(port,
get_time().val +
PD_T_SENDER_RESPONSE,
PD_STATE_SNK_READY);
}
break;
case PD_STATE_SNK_SWAP_SNK_DISABLE:
/* Stop drawing power */
pd_set_input_current_limit(port, 0, 0);
#ifdef CONFIG_CHARGE_MANAGER
typec_set_input_current_limit(port, 0, 0);
charge_manager_set_ceil(port,
CEIL_REQUESTOR_PD,
CHARGE_CEIL_NONE);
#endif
set_state(port, PD_STATE_SNK_SWAP_SRC_DISABLE);
timeout = 10*MSEC;
break;
case PD_STATE_SNK_SWAP_SRC_DISABLE:
/* Wait for PS_RDY */
if (pd[port].last_state != pd[port].task_state)
set_state_timeout(port,
get_time().val +
PD_T_PS_SOURCE_OFF,
PD_STATE_HARD_RESET_SEND);
break;
case PD_STATE_SNK_SWAP_STANDBY:
if (pd[port].last_state != pd[port].task_state) {
/* Switch to Rp and enable power supply. */
tcpm_set_cc(port, TYPEC_CC_RP);
if (pd_set_power_supply_ready(port)) {
/* Restore Rd */
tcpm_set_cc(port, TYPEC_CC_RD);
timeout = 10*MSEC;
set_state(port,
PD_STATE_SNK_DISCONNECTED);
break;
}
/* Wait for power supply to turn on */
set_state_timeout(
port,
get_time().val +
PD_POWER_SUPPLY_TURN_ON_DELAY,
PD_STATE_SNK_SWAP_COMPLETE);
}
break;
case PD_STATE_SNK_SWAP_COMPLETE:
/* Send PS_RDY and change to source role */
res = send_control(port, PD_CTRL_PS_RDY);
if (res < 0) {
/* Restore Rd */
tcpm_set_cc(port, TYPEC_CC_RD);
pd_power_supply_reset(port);
timeout = 10 * MSEC;
set_state(port, PD_STATE_SNK_DISCONNECTED);
break;
}
/* Don't send GET_SINK_CAP on swap */
snk_cap_count = PD_SNK_CAP_RETRIES+1;
caps_count = 0;
pd[port].msg_id = 0;
pd_set_power_role(port, PD_ROLE_SOURCE);
pd_update_roles(port);
set_state(port, PD_STATE_SRC_DISCOVERY);
timeout = 10*MSEC;
break;
#ifdef CONFIG_USBC_VCONN_SWAP
case PD_STATE_VCONN_SWAP_SEND:
if (pd[port].last_state != pd[port].task_state) {
res = send_control(port, PD_CTRL_VCONN_SWAP);
if (res < 0) {
timeout = 10*MSEC;
/*
* If failed to get goodCRC, send
* soft reset, otherwise ignore
* failure.
*/
set_state(port, res == -1 ?
PD_STATE_SOFT_RESET :
READY_RETURN_STATE(port));
break;
}
/* Wait for accept or reject */
set_state_timeout(port,
get_time().val +
PD_T_SENDER_RESPONSE,
READY_RETURN_STATE(port));
}
break;
case PD_STATE_VCONN_SWAP_INIT:
if (pd[port].last_state != pd[port].task_state) {
if (!(pd[port].flags & PD_FLAGS_VCONN_ON)) {
/* Turn VCONN on and wait for it */
set_vconn(port, 1);
set_state_timeout(port,
get_time().val + PD_VCONN_SWAP_DELAY,
PD_STATE_VCONN_SWAP_READY);
} else {
set_state_timeout(port,
get_time().val + PD_T_VCONN_SOURCE_ON,
READY_RETURN_STATE(port));
}
}
break;
case PD_STATE_VCONN_SWAP_READY:
if (pd[port].last_state != pd[port].task_state) {
if (!(pd[port].flags & PD_FLAGS_VCONN_ON)) {
/* VCONN is now on, send PS_RDY */
pd_set_vconn_role(port,
PD_ROLE_VCONN_ON);
res = send_control(port,
PD_CTRL_PS_RDY);
if (res == -1) {
timeout = 10*MSEC;
/*
* If failed to get goodCRC,
* send soft reset
*/
set_state(port,
PD_STATE_SOFT_RESET);
break;
}
set_state(port,
READY_RETURN_STATE(port));
} else {
/* Turn VCONN off and wait for it */
set_vconn(port, 0);
pd_set_vconn_role(port,
PD_ROLE_VCONN_OFF);
set_state_timeout(port,
get_time().val + PD_VCONN_SWAP_DELAY,
READY_RETURN_STATE(port));
}
}
break;
#endif /* CONFIG_USBC_VCONN_SWAP */
#endif /* CONFIG_USB_PD_DUAL_ROLE */
case PD_STATE_SOFT_RESET:
if (pd[port].last_state != pd[port].task_state) {
/* Message ID of soft reset is always 0 */
pd[port].msg_id = 0;
res = send_control(port, PD_CTRL_SOFT_RESET);
/* if soft reset failed, try hard reset. */
if (res < 0) {
set_state(port,
PD_STATE_HARD_RESET_SEND);
timeout = 5*MSEC;
break;
}
set_state_timeout(
port,
get_time().val + PD_T_SENDER_RESPONSE,
PD_STATE_HARD_RESET_SEND);
}
break;
case PD_STATE_HARD_RESET_SEND:
hard_reset_count++;
if (pd[port].last_state != pd[port].task_state)
hard_reset_sent = 0;
#ifdef CONFIG_CHARGE_MANAGER
if (pd[port].last_state == PD_STATE_SNK_DISCOVERY ||
(pd[port].last_state == PD_STATE_SOFT_RESET &&
(pd[port].flags & PD_FLAGS_VBUS_NEVER_LOW))) {
pd[port].flags &= ~PD_FLAGS_VBUS_NEVER_LOW;
/*
* If discovery timed out, assume that we
* have a dedicated charger attached. This
* may not be a correct assumption according
* to the specification, but it generally
* works in practice and the harmful
* effects of a wrong assumption here
* are minimal.
*/
charge_manager_update_dualrole(port,
CAP_DEDICATED);
}
#endif
/* try sending hard reset until it succeeds */
if (!hard_reset_sent) {
if (pd_transmit(port, TCPC_TX_HARD_RESET,
0, NULL) < 0) {
timeout = 10*MSEC;
break;
}
/* successfully sent hard reset */
hard_reset_sent = 1;
/*
* If we are source, delay before cutting power
* to allow sink time to get hard reset.
*/
if (pd[port].power_role == PD_ROLE_SOURCE) {
set_state_timeout(port,
get_time().val + PD_T_PS_HARD_RESET,
PD_STATE_HARD_RESET_EXECUTE);
} else {
set_state(port,
PD_STATE_HARD_RESET_EXECUTE);
timeout = 10*MSEC;
}
}
break;
case PD_STATE_HARD_RESET_EXECUTE:
#ifdef CONFIG_USB_PD_DUAL_ROLE
/*
* If hard reset while in the last stages of power
* swap, then we need to restore our CC resistor.
*/
if (pd[port].last_state == PD_STATE_SNK_SWAP_STANDBY)
tcpm_set_cc(port, TYPEC_CC_RD);
#endif
/* reset our own state machine */
pd_execute_hard_reset(port);
timeout = 10*MSEC;
break;
#ifdef CONFIG_COMMON_RUNTIME
case PD_STATE_BIST_RX:
send_bist_cmd(port);
/* Delay at least enough for partner to finish BIST */
timeout = PD_T_BIST_RECEIVE + 20*MSEC;
/* Set to appropriate port disconnected state */
set_state(port, DUAL_ROLE_IF_ELSE(port,
PD_STATE_SNK_DISCONNECTED,
PD_STATE_SRC_DISCONNECTED));
break;
case PD_STATE_BIST_TX:
pd_transmit(port, TCPC_TX_BIST_MODE_2, 0, NULL);
/* Delay at least enough to finish sending BIST */
timeout = PD_T_BIST_TRANSMIT + 20*MSEC;
/* Set to appropriate port disconnected state */
set_state(port, DUAL_ROLE_IF_ELSE(port,
PD_STATE_SNK_DISCONNECTED,
PD_STATE_SRC_DISCONNECTED));
break;
#endif
#ifdef CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
case PD_STATE_DRP_AUTO_TOGGLE:
{
enum pd_states next_state;
assert(auto_toggle_supported);
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/*
* If SW decided we should be in a low power state and
* the CC lines did not change, then don't talk with the
* TCPC otherwise we might wake it up.
*/
if (pd[port].flags & PD_FLAGS_LPM_REQUESTED &&
!(evt & PD_EVENT_CC))
break;
#endif
/* Check for connection */
tcpm_get_cc(port, &cc1, &cc2);
next_state = drp_auto_toggle_next_state(port, cc1, cc2);
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/*
* The next state is not determined just by what is
* attached, but also depends on DRP_STATE. Regardless
* of next state, if nothing is attached, then always
* request low power mode.
*/
if (cc_is_open(cc1, cc2))
pd[port].flags |= PD_FLAGS_LPM_REQUESTED;
#endif
if (next_state == PD_STATE_SNK_DISCONNECTED) {
tcpm_set_cc(port, TYPEC_CC_RD);
pd_set_power_role(port, PD_ROLE_SINK);
timeout = 2*MSEC;
} else if (next_state == PD_STATE_SRC_DISCONNECTED) {
tcpm_set_cc(port, TYPEC_CC_RP);
pd_set_power_role(port, PD_ROLE_SOURCE);
timeout = 2*MSEC;
} else {
/*
* We are staying in PD_STATE_DRP_AUTO_TOGGLE,
* therefore enable auto-toggle.
*/
tcpm_enable_drp_toggle(port);
pd[port].flags |= PD_FLAGS_TCPC_DRP_TOGGLE;
timeout = -1;
}
set_state(port, next_state);
break;
}
#endif
default:
break;
}
pd[port].last_state = this_state;
/*
* Check for state timeout, and if not check if need to adjust
* timeout value to wake up on the next state timeout.
*/
now = get_time();
if (pd[port].timeout) {
if (now.val >= pd[port].timeout) {
set_state(port, pd[port].timeout_state);
/* On a state timeout, run next state soon */
timeout = timeout < 10*MSEC ? timeout : 10*MSEC;
} else if (pd[port].timeout - now.val < timeout) {
timeout = pd[port].timeout - now.val;
}
}
#ifdef CONFIG_USB_PD_TCPC_LOW_POWER
/* Determine if we need to put the TCPC in low power mode */
if (pd[port].flags & PD_FLAGS_LPM_REQUESTED &&
!(pd[port].flags & PD_FLAGS_LPM_ENGAGED)) {
int64_t time_left;
/* If any task prevents LPM, wait another debounce */
if (pd[port].tasks_preventing_lpm) {
pd[port].low_power_time =
PD_LPM_DEBOUNCE_US + now.val;
}
time_left = pd[port].low_power_time - now.val;
if (time_left <= 0) {
pd[port].flags |= PD_FLAGS_LPM_ENGAGED;
pd[port].flags |= PD_FLAGS_LPM_TRANSITION;
tcpm_enter_low_power_mode(port);
pd[port].flags &= ~PD_FLAGS_LPM_TRANSITION;
CPRINTS("TCPC p%d Enter Low Power Mode", port);
timeout = -1;
} else if (timeout < 0 || timeout > time_left) {
timeout = time_left;
}
}
#endif
/* Check for disconnection if we're connected */
if (!pd_is_connected(port))
continue;
#ifdef CONFIG_USB_PD_DUAL_ROLE
if (pd_is_power_swapping(port))
continue;
#endif
if (pd[port].power_role == PD_ROLE_SOURCE) {
/* Source: detect disconnect by monitoring CC */
tcpm_get_cc(port, &cc1, &cc2);
if (pd[port].polarity)
cc1 = cc2;
if (cc1 == TYPEC_CC_VOLT_OPEN) {
set_state(port, PD_STATE_SRC_DISCONNECTED);
/* Debouncing */
timeout = 10*MSEC;
#ifdef CONFIG_USB_PD_DUAL_ROLE
/*
* If Try.SRC is configured, then ATTACHED_SRC
* needs to transition to TryWait.SNK. Change
* power role to SNK and start state timer.
*/
if (pd_try_src_enable) {
/* Swap roles to sink */
pd_set_power_role(port, PD_ROLE_SINK);
tcpm_set_cc(port, TYPEC_CC_RD);
/* Set timer for TryWait.SNK state */
pd[port].try_src_marker = get_time().val
+ PD_T_DEBOUNCE;
/* Advance to TryWait.SNK state */
set_state(port,
PD_STATE_SNK_DISCONNECTED);
/* Mark state as TryWait.SNK */
pd[port].flags |= PD_FLAGS_TRY_SRC;
}
#endif
}
}
#ifdef CONFIG_USB_PD_DUAL_ROLE
/*
* Sink disconnect if VBUS is low and
* 1) we are not waiting for VBUS to debounce after a power
* role swap.
* 2) we are not recovering from a hard reset.
*/
if (pd[port].power_role == PD_ROLE_SINK &&
pd[port].vbus_debounce_time < get_time().val &&
!pd_is_vbus_present(port) &&
pd[port].task_state != PD_STATE_SNK_HARD_RESET_RECOVER &&
pd[port].task_state != PD_STATE_HARD_RESET_EXECUTE) {
/* Sink: detect disconnect by monitoring VBUS */
set_state(port, PD_STATE_SNK_DISCONNECTED);
/* set timeout small to reconnect fast */
timeout = 5*MSEC;
}
#endif /* CONFIG_USB_PD_DUAL_ROLE */
}
}
#ifdef CONFIG_USB_PD_DUAL_ROLE
static void pd_chipset_resume(void)
{
int i;
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++) {
#ifdef CONFIG_CHARGE_MANAGER
if (charge_manager_get_active_charge_port() != i)
#endif
pd[i].flags |= PD_FLAGS_CHECK_PR_ROLE |
PD_FLAGS_CHECK_DR_ROLE;
pd_set_dual_role(i, PD_DRP_TOGGLE_ON);
}
CPRINTS("PD:S3->S0");
}
DECLARE_HOOK(HOOK_CHIPSET_RESUME, pd_chipset_resume, HOOK_PRIO_DEFAULT);
static void pd_chipset_suspend(void)
{
int i;
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++)
pd_set_dual_role(i, PD_DRP_TOGGLE_OFF);
CPRINTS("PD:S0->S3");
}
DECLARE_HOOK(HOOK_CHIPSET_SUSPEND, pd_chipset_suspend, HOOK_PRIO_DEFAULT);
static void pd_chipset_startup(void)
{
int i;
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++) {
pd_set_dual_role_no_wakeup(i, PD_DRP_TOGGLE_OFF);
pd[i].flags |= PD_FLAGS_CHECK_IDENTITY;
/* Reset cable attributes and flags */
reset_pd_cable(i);
task_set_event(PD_PORT_TO_TASK_ID(i),
PD_EVENT_POWER_STATE_CHANGE |
PD_EVENT_UPDATE_DUAL_ROLE,
0);
}
CPRINTS("PD:S5->S3");
}
DECLARE_HOOK(HOOK_CHIPSET_STARTUP, pd_chipset_startup, HOOK_PRIO_DEFAULT);
static void pd_chipset_shutdown(void)
{
int i;
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++) {
pd_set_dual_role_no_wakeup(i, PD_DRP_FORCE_SINK);
task_set_event(PD_PORT_TO_TASK_ID(i),
PD_EVENT_POWER_STATE_CHANGE |
PD_EVENT_UPDATE_DUAL_ROLE,
0);
}
CPRINTS("PD:S3->S5");
}
DECLARE_HOOK(HOOK_CHIPSET_SHUTDOWN, pd_chipset_shutdown, HOOK_PRIO_DEFAULT);
#endif /* CONFIG_USB_PD_DUAL_ROLE */
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
void pd_prepare_sysjump(void)
{
int i;
/* Exit modes before sysjump so we can cleanly enter again later */
for (i = 0; i < CONFIG_USB_PD_PORT_COUNT; i++) {
/*
* We can't be in an alternate mode if PD comm is disabled or
* the port is suspended, so no need to send the event
*/
if (!pd_comm_is_enabled(i) ||
pd[i].task_state == PD_STATE_SUSPENDED)
continue;
sysjump_task_waiting = task_get_current();
task_set_event(PD_PORT_TO_TASK_ID(i), PD_EVENT_SYSJUMP, 0);
task_wait_event_mask(TASK_EVENT_SYSJUMP_READY, -1);
sysjump_task_waiting = TASK_ID_INVALID;
}
}
#endif
#ifdef CONFIG_COMMON_RUNTIME
/*
* (enable=1) request pd_task transition to the suspended state. hang
* around for a while until we observe the state change. this can
* take a while (like 300ms) on startup when pd_task is sleeping in
* tcpci_tcpm_init.
*
* (enable=0) force pd_task out of the suspended state and into the
* port's default state.
*/
void pd_set_suspend(int port, int enable)
{
int tries = 300;
if (enable) {
pd[port].req_suspend_state = 1;
do {
task_wake(PD_PORT_TO_TASK_ID(port));
if (pd[port].task_state == PD_STATE_SUSPENDED)
break;
msleep(1);
} while (--tries != 0);
if (!tries)
CPRINTS("TCPC p%d set_suspend failed!", port);
} else {
if (pd[port].task_state != PD_STATE_SUSPENDED)
CPRINTS("TCPC p%d suspend disable request "
"while not suspended!", port);
set_state(port, PD_DEFAULT_STATE(port));
/*
* Since we did not service interrupts while we were suspended,
* see if there is a waiting interrupt to be serviced. If the
* interrupt line isn't asserted, we won't communicate with the
* TCPC.
*/
#ifdef HAS_TASK_PD_INT_C0
schedule_deferred_pd_interrupt(port);
#endif
task_wake(PD_PORT_TO_TASK_ID(port));
}
}
#ifdef CONFIG_USB_PD_TCPM_TCPCI
static uint32_t pd_ports_to_resume;
static void resume_pd_port(void)
{
uint32_t port;
uint32_t suspended_ports = atomic_read_clear(&pd_ports_to_resume);
while (suspended_ports) {
port = __builtin_ctz(suspended_ports);
suspended_ports &= ~BIT(port);
pd_set_suspend(port, 0);
}
}
DECLARE_DEFERRED(resume_pd_port);
void pd_deferred_resume(int port)
{
atomic_or(&pd_ports_to_resume, 1 << port);
hook_call_deferred(&resume_pd_port_data, 5 * SECOND);
}
#endif /* CONFIG_USB_PD_DEFERRED_RESUME */
int pd_is_port_enabled(int port)
{
switch (pd[port].task_state) {
case PD_STATE_DISABLED:
case PD_STATE_SUSPENDED:
return 0;
default:
return 1;
}
}
#if defined(CONFIG_CMD_PD) && defined(CONFIG_CMD_PD_FLASH)
static int hex8tou32(char *str, uint32_t *val)
{
char *ptr = str;
uint32_t tmp = 0;
while (*ptr) {
char c = *ptr++;
if (c >= '0' && c <= '9')
tmp = (tmp << 4) + (c - '0');
else if (c >= 'A' && c <= 'F')
tmp = (tmp << 4) + (c - 'A' + 10);
else if (c >= 'a' && c <= 'f')
tmp = (tmp << 4) + (c - 'a' + 10);
else
return EC_ERROR_INVAL;
}
if (ptr != str + 8)
return EC_ERROR_INVAL;
*val = tmp;
return EC_SUCCESS;
}
static int remote_flashing(int argc, char **argv)
{
int port, cnt, cmd;
uint32_t data[VDO_MAX_SIZE-1];
char *e;
static int flash_offset[CONFIG_USB_PD_PORT_COUNT];
if (argc < 4 || argc > (VDO_MAX_SIZE + 4 - 1))
return EC_ERROR_PARAM_COUNT;
port = strtoi(argv[1], &e, 10);
if (*e || port >= CONFIG_USB_PD_PORT_COUNT)
return EC_ERROR_PARAM2;
cnt = 0;
if (!strcasecmp(argv[3], "erase")) {
cmd = VDO_CMD_FLASH_ERASE;
flash_offset[port] = 0;
ccprintf("ERASE ...");
} else if (!strcasecmp(argv[3], "reboot")) {
cmd = VDO_CMD_REBOOT;
ccprintf("REBOOT ...");
} else if (!strcasecmp(argv[3], "signature")) {
cmd = VDO_CMD_ERASE_SIG;
ccprintf("ERASE SIG ...");
} else if (!strcasecmp(argv[3], "info")) {
cmd = VDO_CMD_READ_INFO;
ccprintf("INFO...");
} else if (!strcasecmp(argv[3], "version")) {
cmd = VDO_CMD_VERSION;
ccprintf("VERSION...");
} else {
int i;
argc -= 3;
for (i = 0; i < argc; i++)
if (hex8tou32(argv[i+3], data + i))
return EC_ERROR_INVAL;
cmd = VDO_CMD_FLASH_WRITE;
cnt = argc;
ccprintf("WRITE %d @%04x ...", argc * 4,
flash_offset[port]);
flash_offset[port] += argc * 4;
}
pd_send_vdm(port, USB_VID_GOOGLE, cmd, data, cnt);
/* Wait until VDM is done */
while (pd[port].vdm_state > 0)
task_wait_event(100*MSEC);
ccprintf("DONE %d\n", pd[port].vdm_state);
return EC_SUCCESS;
}
#endif /* defined(CONFIG_CMD_PD) && defined(CONFIG_CMD_PD_FLASH) */
#if defined(CONFIG_USB_PD_ALT_MODE) && !defined(CONFIG_USB_PD_ALT_MODE_DFP)
void pd_send_hpd(int port, enum hpd_event hpd)
{
uint32_t data[1];
int opos = pd_alt_mode(port, USB_SID_DISPLAYPORT);
if (!opos)
return;
data[0] = VDO_DP_STATUS((hpd == hpd_irq), /* IRQ_HPD */
(hpd != hpd_low), /* HPD_HI|LOW */
0, /* request exit DP */
0, /* request exit USB */
0, /* MF pref */
1, /* enabled */
0, /* power low */
0x2);
pd_send_vdm(port, USB_SID_DISPLAYPORT,
VDO_OPOS(opos) | CMD_ATTENTION, data, 1);
/* Wait until VDM is done. */
while (pd[0].vdm_state > 0)
task_wait_event(USB_PD_RX_TMOUT_US * (PD_RETRY_COUNT + 1));
}
#endif
int pd_fetch_acc_log_entry(int port)
{
timestamp_t timeout;
/* Cannot send a VDM now, the host should retry */
if (pd[port].vdm_state > 0)
return pd[port].vdm_state == VDM_STATE_BUSY ?
EC_RES_BUSY : EC_RES_UNAVAILABLE;
pd_send_vdm(port, USB_VID_GOOGLE, VDO_CMD_GET_LOG, NULL, 0);
timeout.val = get_time().val + 75*MSEC;
/* Wait until VDM is done */
while ((pd[port].vdm_state > 0) &&
(get_time().val < timeout.val))
task_wait_event(10*MSEC);
if (pd[port].vdm_state > 0)
return EC_RES_TIMEOUT;
else if (pd[port].vdm_state < 0)
return EC_RES_ERROR;
return EC_RES_SUCCESS;
}
#ifdef CONFIG_USB_PD_DUAL_ROLE
void pd_request_source_voltage(int port, int mv)
{
pd_set_max_voltage(mv);
if (pd[port].task_state == PD_STATE_SNK_READY ||
pd[port].task_state == PD_STATE_SNK_TRANSITION) {
/* Set flag to send new power request in pd_task */
pd[port].new_power_request = 1;
} else {
pd_set_power_role(port, PD_ROLE_SINK);
tcpm_set_cc(port, TYPEC_CC_RD);
set_state(port, PD_STATE_SNK_DISCONNECTED);
}
task_wake(PD_PORT_TO_TASK_ID(port));
}
void pd_set_external_voltage_limit(int port, int mv)
{
pd_set_max_voltage(mv);
if (pd[port].task_state == PD_STATE_SNK_READY ||
pd[port].task_state == PD_STATE_SNK_TRANSITION) {
/* Set flag to send new power request in pd_task */
pd[port].new_power_request = 1;
task_wake(PD_PORT_TO_TASK_ID(port));
}
}
void pd_update_contract(int port)
{
if ((pd[port].task_state >= PD_STATE_SRC_NEGOCIATE) &&
(pd[port].task_state <= PD_STATE_SRC_GET_SINK_CAP)) {
pd[port].flags |= PD_FLAGS_UPDATE_SRC_CAPS;
task_wake(PD_PORT_TO_TASK_ID(port));
}
}
#endif /* CONFIG_USB_PD_DUAL_ROLE */
#ifdef CONFIG_USBC_PPC
static void pd_send_hard_reset(int port)
{
task_set_event(PD_PORT_TO_TASK_ID(port), PD_EVENT_SEND_HARD_RESET, 0);
}
static uint32_t port_oc_reset_req;
static void re_enable_ports(void)
{
uint32_t ports = atomic_read_clear(&port_oc_reset_req);
while (ports) {
int port = __fls(ports);
ports &= ~BIT(port);
/*
* Let the board know that the overcurrent is
* over since we're going to attempt re-enabling
* the port.
*/
board_overcurrent_event(port, 0);
pd_send_hard_reset(port);
/*
* TODO(b/117854867): PD3.0 to send an alert message
* indicating OCP after explicit contract.
*/
}
}
DECLARE_DEFERRED(re_enable_ports);
void pd_handle_overcurrent(int port)
{
/* Keep track of the overcurrent events. */
CPRINTS("C%d: overcurrent!", port);
#ifdef CONFIG_USB_PD_LOGGING
pd_log_event(PD_EVENT_PS_FAULT, PD_LOG_PORT_SIZE(port, 0), PS_FAULT_OCP,
NULL);
#endif /* defined(CONFIG_USB_PD_LOGGING) */
ppc_add_oc_event(port);
/* Let the board specific code know about the OC event. */
board_overcurrent_event(port, 1);
/* Wait 1s before trying to re-enable the port. */
atomic_or(&port_oc_reset_req, BIT(port));
hook_call_deferred(&re_enable_ports_data, SECOND);
}
#endif /* defined(CONFIG_USBC_PPC) */
static int command_pd(int argc, char **argv)
{
int port;
char *e;
if (argc < 2)
return EC_ERROR_PARAM_COUNT;
if (!strcasecmp(argv[1], "dump")) {
if (argc >= 3) {
#ifdef CONFIG_USB_PD_DEBUG_LEVEL
return EC_ERROR_PARAM2;
#else
int level = strtoi(argv[2], &e, 10);
if (*e)
return EC_ERROR_PARAM2;
debug_level = level;
#endif
}
ccprintf("debug=%d\n", debug_level);
return EC_SUCCESS;
}
#ifdef CONFIG_CMD_PD
#ifdef CONFIG_CMD_PD_DEV_DUMP_INFO
else if (!strncasecmp(argv[1], "rwhashtable", 3)) {
int i;
struct ec_params_usb_pd_rw_hash_entry *p;
for (i = 0; i < RW_HASH_ENTRIES; i++) {
p = &rw_hash_table[i];
pd_dev_dump_info(p->dev_id, p->dev_rw_hash);
}
return EC_SUCCESS;
}
#endif /* CONFIG_CMD_PD_DEV_DUMP_INFO */
#ifdef CONFIG_USB_PD_TRY_SRC
else if (!strncasecmp(argv[1], "trysrc", 6)) {
int enable;
if (argc >= 3) {
enable = strtoi(argv[2], &e, 10);
if (*e)
return EC_ERROR_PARAM3;
pd_try_src_enable = enable ? 1 : 0;
}
ccprintf("Try.SRC %s\n", pd_try_src_enable ? "on" : "off");
return EC_SUCCESS;
}
#endif
#endif
/* command: pd <port> <subcmd> [args] */
port = strtoi(argv[1], &e, 10);
if (argc < 3)
return EC_ERROR_PARAM_COUNT;
if (*e || port >= CONFIG_USB_PD_PORT_COUNT)
return EC_ERROR_PARAM2;
#if defined(CONFIG_CMD_PD) && defined(CONFIG_USB_PD_DUAL_ROLE)
if (!strcasecmp(argv[2], "tx")) {
set_state(port, PD_STATE_SNK_DISCOVERY);
task_wake(PD_PORT_TO_TASK_ID(port));
} else if (!strcasecmp(argv[2], "bist_rx")) {
set_state(port, PD_STATE_BIST_RX);
task_wake(PD_PORT_TO_TASK_ID(port));
} else if (!strcasecmp(argv[2], "bist_tx")) {
if (*e)
return EC_ERROR_PARAM3;
set_state(port, PD_STATE_BIST_TX);
task_wake(PD_PORT_TO_TASK_ID(port));
} else if (!strcasecmp(argv[2], "charger")) {
pd_set_power_role(port, PD_ROLE_SOURCE);
tcpm_set_cc(port, TYPEC_CC_RP);
set_state(port, PD_STATE_SRC_DISCONNECTED);
task_wake(PD_PORT_TO_TASK_ID(port));
} else if (!strncasecmp(argv[2], "dev", 3)) {
int max_volt;
if (argc >= 4)
max_volt = strtoi(argv[3], &e, 10) * 1000;
else
max_volt = pd_get_max_voltage();
pd_request_source_voltage(port, max_volt);
ccprintf("max req: %dmV\n", max_volt);
} else if (!strcasecmp(argv[2], "disable")) {
pd_comm_enable(port, 0);
ccprintf("Port C%d disable\n", port);
return EC_SUCCESS;
} else if (!strcasecmp(argv[2], "enable")) {
pd_comm_enable(port, 1);
ccprintf("Port C%d enabled\n", port);
return EC_SUCCESS;
} else if (!strncasecmp(argv[2], "hard", 4)) {
set_state(port, PD_STATE_HARD_RESET_SEND);
task_wake(PD_PORT_TO_TASK_ID(port));
} else if (!strncasecmp(argv[2], "info", 4)) {
int i;
ccprintf("Hash ");
for (i = 0; i < PD_RW_HASH_SIZE / 4; i++)
ccprintf("%08x ", pd[port].dev_rw_hash[i]);
ccprintf("\nImage %s\n", system_image_copy_t_to_string(
(enum system_image_copy_t)pd[port].current_image));
} else if (!strncasecmp(argv[2], "soft", 4)) {
set_state(port, PD_STATE_SOFT_RESET);
task_wake(PD_PORT_TO_TASK_ID(port));
} else if (!strncasecmp(argv[2], "swap", 4)) {
if (argc < 4)
return EC_ERROR_PARAM_COUNT;
if (!strncasecmp(argv[3], "power", 5))
pd_request_power_swap(port);
else if (!strncasecmp(argv[3], "data", 4))
pd_request_data_swap(port);
#ifdef CONFIG_USBC_VCONN_SWAP
else if (!strncasecmp(argv[3], "vconn", 5))
pd_request_vconn_swap(port);
#endif
else
return EC_ERROR_PARAM3;
} else if (!strncasecmp(argv[2], "ping", 4)) {
int enable;
if (argc > 3) {
enable = strtoi(argv[3], &e, 10);
if (*e)
return EC_ERROR_PARAM3;
pd_ping_enable(port, enable);
}
ccprintf("Pings %s\n",
(pd[port].flags & PD_FLAGS_PING_ENABLED) ?
"on" : "off");
} else if (!strncasecmp(argv[2], "vdm", 3)) {
if (argc < 4)
return EC_ERROR_PARAM_COUNT;
if (!strncasecmp(argv[3], "ping", 4)) {
uint32_t enable;
if (argc < 5)
return EC_ERROR_PARAM_COUNT;
enable = strtoi(argv[4], &e, 10);
if (*e)
return EC_ERROR_PARAM4;
pd_send_vdm(port, USB_VID_GOOGLE, VDO_CMD_PING_ENABLE,
&enable, 1);
} else if (!strncasecmp(argv[3], "curr", 4)) {
pd_send_vdm(port, USB_VID_GOOGLE, VDO_CMD_CURRENT,
NULL, 0);
} else if (!strncasecmp(argv[3], "vers", 4)) {
pd_send_vdm(port, USB_VID_GOOGLE, VDO_CMD_VERSION,
NULL, 0);
} else {
return EC_ERROR_PARAM_COUNT;
}
#if defined(CONFIG_CMD_PD) && defined(CONFIG_CMD_PD_FLASH)
} else if (!strncasecmp(argv[2], "flash", 4)) {
return remote_flashing(argc, argv);
#endif
#if defined(CONFIG_CMD_PD) && defined(CONFIG_USB_PD_DUAL_ROLE)
} else if (!strcasecmp(argv[2], "dualrole")) {
if (argc < 4) {
ccprintf("dual-role toggling: ");
switch (drp_state[port]) {
case PD_DRP_TOGGLE_ON:
ccprintf("on\n");
break;
case PD_DRP_TOGGLE_OFF:
ccprintf("off\n");
break;
case PD_DRP_FREEZE:
ccprintf("freeze\n");
break;
case PD_DRP_FORCE_SINK:
ccprintf("force sink\n");
break;
case PD_DRP_FORCE_SOURCE:
ccprintf("force source\n");
break;
}
} else {
if (!strcasecmp(argv[3], "on"))
pd_set_dual_role(port, PD_DRP_TOGGLE_ON);
else if (!strcasecmp(argv[3], "off"))
pd_set_dual_role(port, PD_DRP_TOGGLE_OFF);
else if (!strcasecmp(argv[3], "freeze"))
pd_set_dual_role(port, PD_DRP_FREEZE);
else if (!strcasecmp(argv[3], "sink"))
pd_set_dual_role(port, PD_DRP_FORCE_SINK);
else if (!strcasecmp(argv[3], "source"))
pd_set_dual_role(port,
PD_DRP_FORCE_SOURCE);
else
return EC_ERROR_PARAM4;
}
return EC_SUCCESS;
#endif
} else
#endif
if (!strncasecmp(argv[2], "state", 5)) {
ccprintf("Port C%d CC%d, %s - Role: %s-%s%s "
"State: %d(%s), Flags: 0x%04x\n",
port, pd[port].polarity + 1,
pd_comm_is_enabled(port) ? "Ena" : "Dis",
pd[port].power_role == PD_ROLE_SOURCE ? "SRC" : "SNK",
pd[port].data_role == PD_ROLE_DFP ? "DFP" : "UFP",
(pd[port].flags & PD_FLAGS_VCONN_ON) ? "-VC" : "",
pd[port].task_state,
debug_level > 0 ?
pd_state_names[pd[port].task_state] : "",
pd[port].flags);
} else {
return EC_ERROR_PARAM1;
}
return EC_SUCCESS;
}
DECLARE_CONSOLE_COMMAND(pd, command_pd,
"dump"
#ifdef CONFIG_USB_PD_TRY_SRC
"|trysrc"
#endif
" [0|1|2]"
#ifdef CONFIG_CMD_PD_DEV_DUMP_INFO
"|rwhashtable"
#endif
"\n\t<port> state"
#ifdef CONFIG_USB_PD_DUAL_ROLE
"|tx|bist_rx|bist_tx|charger|dev"
"\n\t<port> disable|enable|soft|info|hard|ping"
"\n\t<port> dualrole [on|off|freeze|sink|source]"
"\n\t<port> swap [power|data|vconn]"
"\n\t<port> vdm [ping|curr|vers]"
#ifdef CONFIG_CMD_PD_FLASH
"\n\t<port> flash [erase|reboot|signature|info|version]"
#endif /* CONFIG_CMD_PD_FLASH */
#endif /* CONFIG_USB_PD_DUAL_ROLE */
,
"USB PD");
#ifdef HAS_TASK_HOSTCMD
static enum ec_status hc_pd_ports(struct host_cmd_handler_args *args)
{
struct ec_response_usb_pd_ports *r = args->response;
r->num_ports = CONFIG_USB_PD_PORT_COUNT;
args->response_size = sizeof(*r);
return EC_RES_SUCCESS;
}
DECLARE_HOST_COMMAND(EC_CMD_USB_PD_PORTS,
hc_pd_ports,
EC_VER_MASK(0));
#ifdef CONFIG_USB_PD_DUAL_ROLE
static const enum pd_dual_role_states dual_role_map[USB_PD_CTRL_ROLE_COUNT] = {
[USB_PD_CTRL_ROLE_TOGGLE_ON] = PD_DRP_TOGGLE_ON,
[USB_PD_CTRL_ROLE_TOGGLE_OFF] = PD_DRP_TOGGLE_OFF,
[USB_PD_CTRL_ROLE_FORCE_SINK] = PD_DRP_FORCE_SINK,
[USB_PD_CTRL_ROLE_FORCE_SOURCE] = PD_DRP_FORCE_SOURCE,
[USB_PD_CTRL_ROLE_FREEZE] = PD_DRP_FREEZE,
};
#endif
#ifdef CONFIG_USBC_SS_MUX
static const enum typec_mux typec_mux_map[USB_PD_CTRL_MUX_COUNT] = {
[USB_PD_CTRL_MUX_NONE] = TYPEC_MUX_NONE,
[USB_PD_CTRL_MUX_USB] = TYPEC_MUX_USB,
[USB_PD_CTRL_MUX_AUTO] = TYPEC_MUX_DP,
[USB_PD_CTRL_MUX_DP] = TYPEC_MUX_DP,
[USB_PD_CTRL_MUX_DOCK] = TYPEC_MUX_DOCK,
};
#endif
__attribute__((weak)) uint8_t board_get_dp_pin_mode(int port)
{
return 0;
}
static enum ec_status hc_usb_pd_control(struct host_cmd_handler_args *args)
{
const struct ec_params_usb_pd_control *p = args->params;
struct ec_response_usb_pd_control_v2 *r_v2 = args->response;
struct ec_response_usb_pd_control_v1 *r_v1 = args->response;
struct ec_response_usb_pd_control *r = args->response;
if (p->port >= CONFIG_USB_PD_PORT_COUNT)
return EC_RES_INVALID_PARAM;
if (p->role >= USB_PD_CTRL_ROLE_COUNT ||
p->mux >= USB_PD_CTRL_MUX_COUNT)
return EC_RES_INVALID_PARAM;
if (p->role != USB_PD_CTRL_ROLE_NO_CHANGE)
#ifdef CONFIG_USB_PD_DUAL_ROLE
pd_set_dual_role(p->port, dual_role_map[p->role]);
#else
return EC_RES_INVALID_PARAM;
#endif
#ifdef CONFIG_USBC_SS_MUX
if (p->mux != USB_PD_CTRL_MUX_NO_CHANGE)
usb_mux_set(p->port, typec_mux_map[p->mux],
typec_mux_map[p->mux] == TYPEC_MUX_NONE ?
USB_SWITCH_DISCONNECT :
USB_SWITCH_CONNECT,
pd_get_polarity(p->port));
#endif /* CONFIG_USBC_SS_MUX */
if (p->swap == USB_PD_CTRL_SWAP_DATA)
pd_request_data_swap(p->port);
#ifdef CONFIG_USB_PD_DUAL_ROLE
else if (p->swap == USB_PD_CTRL_SWAP_POWER)
pd_request_power_swap(p->port);
#ifdef CONFIG_USBC_VCONN_SWAP
else if (p->swap == USB_PD_CTRL_SWAP_VCONN)
pd_request_vconn_swap(p->port);
#endif
#endif
switch (args->version) {
case 0:
r->enabled = pd_comm_is_enabled(p->port);
r->role = pd[p->port].power_role;
r->polarity = pd[p->port].polarity;
r->state = pd[p->port].task_state;
args->response_size = sizeof(*r);
break;
case 1:
case 2:
r_v2->enabled =
(pd_comm_is_enabled(p->port) ?
PD_CTRL_RESP_ENABLED_COMMS : 0) |
(pd_is_connected(p->port) ?
PD_CTRL_RESP_ENABLED_CONNECTED : 0) |
((pd[p->port].flags & PD_FLAGS_PREVIOUS_PD_CONN) ?
PD_CTRL_RESP_ENABLED_PD_CAPABLE : 0);
r_v2->role =
(pd[p->port].power_role ? PD_CTRL_RESP_ROLE_POWER : 0) |
(pd[p->port].data_role ? PD_CTRL_RESP_ROLE_DATA : 0) |
((pd[p->port].flags & PD_FLAGS_VCONN_ON) ?
PD_CTRL_RESP_ROLE_VCONN : 0) |
((pd[p->port].flags & PD_FLAGS_PARTNER_DR_POWER) ?
PD_CTRL_RESP_ROLE_DR_POWER : 0) |
((pd[p->port].flags & PD_FLAGS_PARTNER_DR_DATA) ?
PD_CTRL_RESP_ROLE_DR_DATA : 0) |
((pd[p->port].flags & PD_FLAGS_PARTNER_USB_COMM) ?
PD_CTRL_RESP_ROLE_USB_COMM : 0) |
((pd[p->port].flags & PD_FLAGS_PARTNER_EXTPOWER) ?
PD_CTRL_RESP_ROLE_EXT_POWERED : 0);
r_v2->polarity = pd[p->port].polarity;
if (debug_level > 0)
strzcpy(r_v2->state,
pd_state_names[pd[p->port].task_state],
sizeof(r_v2->state));
else
r_v2->state[0] = '\0';
r_v2->cc_state = pd[p->port].cc_state;
r_v2->dp_mode = board_get_dp_pin_mode(p->port);
r_v2->cable_type = get_usb_pd_mux_cable_type(p->port);
if (args->version == 1)
args->response_size = sizeof(*r_v1);
else
args->response_size = sizeof(*r_v2);
break;
default:
return EC_RES_INVALID_PARAM;
}
return EC_RES_SUCCESS;
}
DECLARE_HOST_COMMAND(EC_CMD_USB_PD_CONTROL,
hc_usb_pd_control,
EC_VER_MASK(0) | EC_VER_MASK(1) | EC_VER_MASK(2));
#ifdef CONFIG_HOSTCMD_FLASHPD
static enum ec_status hc_remote_flash(struct host_cmd_handler_args *args)
{
const struct ec_params_usb_pd_fw_update *p = args->params;
int port = p->port;
const uint32_t *data = &(p->size) + 1;
int i, size, rv = EC_RES_SUCCESS;
timestamp_t timeout;
if (port >= CONFIG_USB_PD_PORT_COUNT)
return EC_RES_INVALID_PARAM;
if (p->size + sizeof(*p) > args->params_size)
return EC_RES_INVALID_PARAM;
#if defined(CONFIG_BATTERY_PRESENT_CUSTOM) || \
defined(CONFIG_BATTERY_PRESENT_GPIO)
/*
* Do not allow PD firmware update if no battery and this port
* is sinking power, because we will lose power.
*/
if (battery_is_present() != BP_YES &&
charge_manager_get_active_charge_port() == port)
return EC_RES_UNAVAILABLE;
#endif
/*
* Busy still with a VDM that host likely generated. 1 deep VDM queue
* so just return for retry logic on host side to deal with.
*/
if (pd[port].vdm_state > 0)
return EC_RES_BUSY;
switch (p->cmd) {
case USB_PD_FW_REBOOT:
pd_send_vdm(port, USB_VID_GOOGLE, VDO_CMD_REBOOT, NULL, 0);
/*
* Return immediately to free pending i2c bus. Host needs to
* manage this delay.
*/
return EC_RES_SUCCESS;
case USB_PD_FW_FLASH_ERASE:
pd_send_vdm(port, USB_VID_GOOGLE, VDO_CMD_FLASH_ERASE, NULL, 0);
/*
* Return immediately. Host needs to manage delays here which
* can be as long as 1.2 seconds on 64KB RW flash.
*/
return EC_RES_SUCCESS;
case USB_PD_FW_ERASE_SIG:
pd_send_vdm(port, USB_VID_GOOGLE, VDO_CMD_ERASE_SIG, NULL, 0);
timeout.val = get_time().val + 500*MSEC;
break;
case USB_PD_FW_FLASH_WRITE:
/* Data size must be a multiple of 4 */
if (!p->size || p->size % 4)
return EC_RES_INVALID_PARAM;
size = p->size / 4;
for (i = 0; i < size; i += VDO_MAX_SIZE - 1) {
pd_send_vdm(port, USB_VID_GOOGLE, VDO_CMD_FLASH_WRITE,
data + i, MIN(size - i, VDO_MAX_SIZE - 1));
timeout.val = get_time().val + 500*MSEC;
/* Wait until VDM is done */
while ((pd[port].vdm_state > 0) &&
(get_time().val < timeout.val))
task_wait_event(10*MSEC);
if (pd[port].vdm_state > 0)
return EC_RES_TIMEOUT;
}
return EC_RES_SUCCESS;
default:
return EC_RES_INVALID_PARAM;
break;
}
/* Wait until VDM is done or timeout */
while ((pd[port].vdm_state > 0) && (get_time().val < timeout.val))
task_wait_event(50*MSEC);
if ((pd[port].vdm_state > 0) ||
(pd[port].vdm_state == VDM_STATE_ERR_TMOUT))
rv = EC_RES_TIMEOUT;
else if (pd[port].vdm_state < 0)
rv = EC_RES_ERROR;
return rv;
}
DECLARE_HOST_COMMAND(EC_CMD_USB_PD_FW_UPDATE,
hc_remote_flash,
EC_VER_MASK(0));
#endif /* CONFIG_HOSTCMD_FLASHPD */
#ifdef CONFIG_HOSTCMD_RWHASHPD
static enum ec_status
hc_remote_rw_hash_entry(struct host_cmd_handler_args *args)
{
int i, idx = 0, found = 0;
const struct ec_params_usb_pd_rw_hash_entry *p = args->params;
static int rw_hash_next_idx;
if (!p->dev_id)
return EC_RES_INVALID_PARAM;
for (i = 0; i < RW_HASH_ENTRIES; i++) {
if (p->dev_id == rw_hash_table[i].dev_id) {
idx = i;
found = 1;
break;
}
}
if (!found) {
idx = rw_hash_next_idx;
rw_hash_next_idx = rw_hash_next_idx + 1;
if (rw_hash_next_idx == RW_HASH_ENTRIES)
rw_hash_next_idx = 0;
}
memcpy(&rw_hash_table[idx], p, sizeof(*p));
return EC_RES_SUCCESS;
}
DECLARE_HOST_COMMAND(EC_CMD_USB_PD_RW_HASH_ENTRY,
hc_remote_rw_hash_entry,
EC_VER_MASK(0));
#endif /* CONFIG_HOSTCMD_RWHASHPD */
static enum ec_status hc_remote_pd_dev_info(struct host_cmd_handler_args *args)
{
const uint8_t *port = args->params;
struct ec_params_usb_pd_rw_hash_entry *r = args->response;
if (*port >= CONFIG_USB_PD_PORT_COUNT)
return EC_RES_INVALID_PARAM;
r->dev_id = pd[*port].dev_id;
if (r->dev_id) {
memcpy(r->dev_rw_hash, pd[*port].dev_rw_hash,
PD_RW_HASH_SIZE);
}
r->current_image = pd[*port].current_image;
args->response_size = sizeof(*r);
return EC_RES_SUCCESS;
}
DECLARE_HOST_COMMAND(EC_CMD_USB_PD_DEV_INFO,
hc_remote_pd_dev_info,
EC_VER_MASK(0));
#ifndef CONFIG_USB_PD_TCPC
#ifdef CONFIG_EC_CMD_PD_CHIP_INFO
static enum ec_status hc_remote_pd_chip_info(struct host_cmd_handler_args *args)
{
const struct ec_params_pd_chip_info *p = args->params;
struct ec_response_pd_chip_info_v1 *info;
if (p->port >= CONFIG_USB_PD_PORT_COUNT)
return EC_RES_INVALID_PARAM;
if (tcpm_get_chip_info(p->port, p->live, &info))
return EC_RES_ERROR;
/*
* Take advantage of the fact that v0 and v1 structs have the
* same layout for v0 data. (v1 just appends data)
*/
args->response_size =
args->version ? sizeof(struct ec_response_pd_chip_info_v1)
: sizeof(struct ec_response_pd_chip_info);
memcpy(args->response, info, args->response_size);
return EC_RES_SUCCESS;
}
DECLARE_HOST_COMMAND(EC_CMD_PD_CHIP_INFO,
hc_remote_pd_chip_info,
EC_VER_MASK(0) | EC_VER_MASK(1));
#endif
#endif
#ifdef CONFIG_USB_PD_ALT_MODE_DFP
static enum ec_status hc_remote_pd_set_amode(struct host_cmd_handler_args *args)
{
const struct ec_params_usb_pd_set_mode_request *p = args->params;
if ((p->port >= CONFIG_USB_PD_PORT_COUNT) || (!p->svid) || (!p->opos))
return EC_RES_INVALID_PARAM;
switch (p->cmd) {
case PD_EXIT_MODE:
if (pd_dfp_exit_mode(p->port, p->svid, p->opos))
pd_send_vdm(p->port, p->svid,
CMD_EXIT_MODE | VDO_OPOS(p->opos), NULL, 0);
else {
CPRINTF("Failed exit mode\n");
return EC_RES_ERROR;
}
break;
case PD_ENTER_MODE:
if (pd_dfp_enter_mode(p->port, p->svid, p->opos))
pd_send_vdm(p->port, p->svid, CMD_ENTER_MODE |
VDO_OPOS(p->opos), NULL, 0);
break;
default:
return EC_RES_INVALID_PARAM;
}
return EC_RES_SUCCESS;
}
DECLARE_HOST_COMMAND(EC_CMD_USB_PD_SET_AMODE,
hc_remote_pd_set_amode,
EC_VER_MASK(0));
#endif /* CONFIG_USB_PD_ALT_MODE_DFP */
#endif /* HAS_TASK_HOSTCMD */
#ifdef CONFIG_CMD_PD_CONTROL
static enum ec_status pd_control(struct host_cmd_handler_args *args)
{
static int pd_control_disabled[CONFIG_USB_PD_PORT_COUNT];
const struct ec_params_pd_control *cmd = args->params;
int enable = 0;
if (cmd->chip >= CONFIG_USB_PD_PORT_COUNT)
return EC_RES_INVALID_PARAM;
/* Always allow disable command */
if (cmd->subcmd == PD_CONTROL_DISABLE) {
pd_control_disabled[cmd->chip] = 1;
return EC_RES_SUCCESS;
}
if (pd_control_disabled[cmd->chip])
return EC_RES_ACCESS_DENIED;
if (cmd->subcmd == PD_SUSPEND) {
/*
* The AP is requesting to suspend PD traffic on the EC so it
* can perform a firmware upgrade. If Vbus is present on the
* connector (it is either a source or sink), then we will
* prevent the upgrade if there is not enough battery to finish
* the upgrade. We cannot rely on the EC's active charger data
* as the EC just rebooted into RW and has not necessarily
* picked the active charger yet.
*/
#ifdef HAS_TASK_CHARGER
if (pd_is_vbus_present(cmd->chip)) {
struct batt_params batt = { 0 };
/*
* The charger task has not re-initialized, so we need
* to ask the battery directly.
*/
battery_get_params(&batt);
if (batt.remaining_capacity <
MIN_BATTERY_FOR_TCPC_UPGRADE_MAH ||
batt.flags & BATT_FLAG_BAD_REMAINING_CAPACITY) {
CPRINTS("C%d: Cannot suspend for upgrade, not "
"enough battery (%dmAh)!",
cmd->chip, batt.remaining_capacity);
return EC_RES_BUSY;
}
}
#else
if (pd_is_vbus_present(cmd->chip)) {
CPRINTS("C%d: Cannot suspend for upgrade, Vbus "
"present!",
cmd->chip);
return EC_RES_BUSY;
}
#endif
enable = 0;
} else if (cmd->subcmd == PD_RESUME) {
enable = 1;
} else if (cmd->subcmd == PD_RESET) {
#ifdef HAS_TASK_PDCMD
board_reset_pd_mcu();
#else
return EC_RES_INVALID_COMMAND;
#endif
} else if (cmd->subcmd == PD_CHIP_ON && board_set_tcpc_power_mode) {
board_set_tcpc_power_mode(cmd->chip, 1);
return EC_RES_SUCCESS;
} else {
return EC_RES_INVALID_COMMAND;
}
pd_comm_enable(cmd->chip, enable);
pd_set_suspend(cmd->chip, !enable);
return EC_RES_SUCCESS;
}
DECLARE_HOST_COMMAND(EC_CMD_PD_CONTROL, pd_control, EC_VER_MASK(0));
#endif /* CONFIG_CMD_PD_CONTROL */
#endif /* CONFIG_COMMON_RUNTIME */